Continuous Production Of Monoclonal Antibodies Research Articles

Advanced control strategies for continuous capture of monoclonal antibodies based upon biolayer interferometry.

The semi and fully continuous production of monoclonal antibodies (mAbs) has been gaining traction as a lower cost, and efficient production of mAbs to broaden patient access. To be truly flexible and adaptive to process demands, the industry has lacked sufficient advanced control strategies. The variation of the upstream product concentration typically cannot be handled by the downstream capture step, which is configured for a constant feed concentration and fixed binding capacity. This inflexibility leads to losses of efficiency and product yield. This study shows that these challenges can be overcome by a novel advanced control strategy concept that includes dynamic control throughout a perfusion bioreactor, with cell retention by alternating tangential flow, integrated with simulated moving bed (SMB) multi-column chromatography. The automation workflow and advanced control strategy were implemented through the use of a visual programming development environment. This enabled dynamic flow control across the upstream and downstream process integrated with a dynamic column loading of the SMB. A sensor prototype, based on continuous biolayer interferometry measurements was applied to detect mAb breakthrough within the last column flow-through to manage column switching. This novel approach provided higher specificity and lower background signal compared to commonly used spectroscopy methods, resulting in an optimized resin utilization while simultaneously avoiding product loss. The dynamic loading was found to provide a twofold increase of the mAb concentration in the eluate compared to a conservative approach with a predefined recipe with similar impurity removal. This concept shows that advanced control strategies can lead to significant process efficiency and yield improvement.

Model predictive control for steady-state performance in integrated continuous bioprocesses

Perfusion bioreactors are commonly used for the continuous production of monoclonal antibodies (mAb). One potential benefit of continuous bioprocessing is the ability to operate under steady-state conditions for an extended process time. However, the process performance is often limited by the feedback control of feed, harvest, and bleed flow rates. If the future behavior of a bioprocess can be adequately described, predictive control can reduce set point deviations and thereby maximize process stability. In this study, we investigated the predictive control of biomass in a perfusion bioreactor integrated to a non-chromatographic capture step, in a series of Monte-Carlo simulations. A simple algorithm was developed to estimate the current and predict the future viable cell concentrations (VCC) of the bioprocess. This feature enabled the single prediction controller (SPC) to compensate for process variations that would normally be transported to adjacent units in integrated continuous bioprocesses (ICB). Use of this SPC strategy significantly reduced biomass, product concentration, and harvest flow variability and stabilized the operation over long periods of time compared to simulations using feedback control strategies. Additionally, we demonstrated the possibility of maximizing product yields simply by adjusting perfusion control strategies. This method could be used to prevent savings in total product losses of 4.5–10% over 30 days of protein production.

Simulation of continuous low pH viral inactivation inside a coiled flow inverter.

Continuous production of monoclonal antibodies is gaining more and more importance. To ensure continuous flow through the entire process as well as viral safety, continuous viral clearance needs to be investigated as well. This study focuses on low pH viral inactivation inside a coiled flow inverter (CFI). Computational fluid dynamics (CFD) simulation is used to gain further insight into the inactivation process inside the apparatus. The influence of viruses in comparison to different tracer elements on the residence time distribution (RTD) behavior is investigated. Finally, the viral inactivation kinetics are implemented into the CFD simulation and real process conditions are simulated. These are compared to experimental results. To the authors' knowledge, this study represents the first successful simulation of continuous viral inactivation inside a CFI. It allows the detailed analysis of processes inside the apparatus and the prediction of experimental virus study results and will therefore contribute to the effective planning of future validation studies.

An NIR-based PAT approach for real-time control of loading in Protein A chromatography in continuous manufacturing of monoclonal antibodies.

Control of column loading in Protein A chromatography is a crucial part of development of robust and flexible process platforms for continuous production of monoclonal antibody (mAb) products. In this paper, we propose a control system that uses near infrared spectroscopy (NIRS) flow cells to accomplish the above. Two applications have been demonstrated using a periodic counter-current continuous chromatography setup. The first application involves use of single NIR flow cell before the inlet of the loading column to measure the concentration of mAb in the harvested broth. Measurement was in real-time (every 3 s) and within ±0.05 mg/ml, significantly better than making UV-based concentration estimations. The second application involved use of an additional NIR flow cell at the outlet of the loading column to measure column breakthrough in real time. The concentration data was transferred to a Python-based monitoring and control algorithm layered over a Cadence BioSMB system. The program could successfully run a three-column periodic counter current method on the BioSMB whereas controlling loading to ensure optimal resin utilization in each loading cycle phase based on precharacterized dynamic binding capacity models, whereas maintaining periodic elutions. The system was tested with multiple perturbations in harvest concentration, modeled after deviations that could arise downstream of a perfusion cell culture system. The results show that the proposed control is a spectroscopy-based process analytical technology tool that facilitates real time monitoring and control of loading in process chromatography. It is adaptable to any continuous chromatography equipment and is very well suited for implementation in a continuous mAb production train.

Simulation of pH level distribution inside a coiled flow inverter for continuous low pH viral inactivation.

The continuous production of monoclonal antibodies (mAbs) with the help of disposable equipment poses one of the future major changes in the pharmaceutical industry. Consequently, continuous viral clearance needs to be developed as well. The coiled flow inverter (CFI) was successfully implemented in the continuous downstream as a residence time module for low pH viral inactivation. As the elution profile of the upstream continuously operated protein A chromatography results in fluctuating pH values, the pH level distribution inside the CFI is highly relevant. This study presents a detailed investigation of pH level distribution inside the CFI at varying inlet conditions with the help of computational fluid dynamics simulation. The simulation model was validated first with the help of experimental data. Afterwards, the model was used for further investigations. It was determined that with a pH sine curve as input, the duration until steady state at the outlet requires two times the minimum residence time of the apparatus. Moreover, it could be observed that the CFI itself offers a progressive dampening effect on the pH level distribution. Afterwards, different forms of the sine curve representing different operation modes of the continuous protein A chromatograph were tested to evaluate this dampening capability. It became clear that the switch time has the highest influence on the resulting pH of the outlet stream and should be considered for process development. Finally, the radial pH profiles at different positions inside the CFI were determined. This once again revealed the high radial mixing capability of the CFI and its influence on the resulting product stream.

Monoclonal Antibody Production Using a New Supermacroporous Cryogel Bioreactor

A supermacroporous cryogel bioreactor has been developed to culture hybridoma cells for long-term continuous production of monoclonal antibodies (mAb). Hybridoma clone M2139, secreting antibodies against J1 epitope (GERGAAGIAGPK; amino acids, 551-564) of collagen type II, are immobilized in the porous bed matrix of a cryogel column (10 mL bed volume). The cells got attached to the matrix within 48 h after inoculation and grew as a confluent sheet inside the cryogel matrix. Cells were in the lag phase for 15 days and secreted mAb into the circulation medium. Glucose consumption and lactic acid production were also monitored, and during the exponential phase (approximately 20 days), the hybridoma cell line consumed 0.75 mM day-1 glucose, produced 2.48 mM day-1 lactic acid, and produced 6.5 microg mL-1 day-1 mAb during the exponential phase. The mAb concentration reached 130 microg mL-1 after continuous run of the cryogel column for 36 days. The yield of the mAb after purification was 67.5 mg L-1, which was three times greater than the mAb yield obtained from T-flask batch cultivation. Even after the exchange of medium reservoir, cells in the cryogel column were still active and had relatively stable mAb production for an extended period of time. The bioreactor was operated continuously for 55 days without any contamination. The results from ELISA as well as arthritis experiments demonstrate that the antibodies secreted by cells grown on the cryogel column did not differ from antibodies purified from the cells grown in commercial CL-1000 culture flasks. Thus, supermacroporous cryogels can be useful as a supporting material for productive hybridoma cell culture. Cells were found to be viable inside the porous matrix of the cryogel during the study period and secreted antibodies continuously. The antibodies thus obtained from the cryogel reactor were found to be functionally active in vivo, as demonstrated by their capacity to induce arthritis in mice.

Cosecretion of Protease Inhibitor Stabilizes Antibodies Produced by Plant Roots

A plant-based system for continuous production of monoclonal antibodies based on the secretion of immunoglobulin complexes from plant roots into a hydroponic medium (rhizosecretion) was engineered to produce high levels of single-chain and full-size immunoglobulins. Replacing the original signal peptides of monoclonal antibodies with a plant-derived calreticulin signal increased the levels of antibody yield 2-fold. Cosecretion of Bowman-Birk Ser protease inhibitor reduced degradation of the immunoglobulin complexes in the default secretion pathway and further increased antibody production to 36.4 microg/g root dry weight per day for single-chain IgG1 and 21.8 microg/g root dry weight per day for full-size IgG4 antibodies. These results suggest that constitutive cosecretion of a protease inhibitor combined with the use of the plant signal peptide and the antibiotic marker-free transformation system offers a novel strategy to achieve high yields of complex therapeutic proteins secreted from plant roots.

Continuous production of monoclonal antibody in a packed‐bed bioreactor

In the present study the growth and MAb (monoclonal antibody) production of a mouse x mouse hybridoma cell producing anti-digoxin MAb was evaluated. The hybridoma cells entrapped within the support matrix Fibra-Cel were cultured in batch and continuous mode following special protocols. Cell-culture studies were performed in a 1-litre spinner basket containing 3 g.litre-1 support matrix. Batch culture was operated with the cell density of 42x10(6) cells. During the 7 days of culture, the medium was sampled daily in order to assess glucose and MAb concentrations and the lactate dehydrogenase released into the culture medium. After a culture period of 72 h, the cell density and MAb concentration were found to be 10.4x10(7) cells/3 g of NWPF (non-woven polyester fibre) discs and 250 microg/ml respectively. This yield gradually decreased to 0.55x10(6) cells/3 g of packaging material and 60 microg/ml respectively at the end of the batch culture. In the continuous-culture studies, the batch culture was initially operated for 64.5 h and then continuous flow was started at the dilution rates of 0.15, 0.2, 0.25 and 0.3 day-1 and finally stabilized at 0.25 day-1 within 288 h (12 days). The MAb concentration at steady state was found to be 116-120 microg/day per ml, and the yield of operation was 62.5 mg/day per ml, which was 3.5 times higher than that of batch culture. In conclusion, a packed-bed bioreactor with the support matrix Fibra-Cel, operated in continuous-feeding mode, is more efficient for large-scale MAb production than a batch culture. On the other hand, by using a continuous-culture system, a better supply of nutrients and removal of inhibitory metabolites and proteolytic enzymes was obtained.

A fibrous-bed bioreactor for continuous production of monoclonal antibody by hybridoma.

A fibrous-bed bioreactor (FBB) has been developed to culture hybridoma cells for long-term continuous production of monoclonal antibody (MAb). A non-woven polyester fibrous matrix was used to immobilize the cells to reach a high viable cell density of 3 x 10(8) cells cm(-3) packed bed, which gave a high volumetric MAb productivity of 1 g L(-1) day(-1) under continuous feed conditions with the medium containing 10% serum. Reducing the medium serum content to 1% increased MAb production to 6.5 g L(-1) day(-1) in a repeated batch FBB culture. MAb production was higher at higher dissolved oxygen (DO) levels in the range between 10% and 70% of air saturation, although DO did not significantly affect glucose metabolism and lactate production. The medium LDH (lactate dehydrogenase) level increased dramatically when the DO level was decreased from 30% to 10%, suggesting that a critical DO level of approximately 30% is necessary for maintaining the FBB culture for long-term operation. Compared with suspension cultures in T-flasks and spinner flasks, the FBB culture had a lower lactate yield from glucose (0.80 vs. 0.91 g g(-1), produced MAb at a higher concentration (up to 442 mg L(-1) vs. 83.5 mg L(-1), and was stable for continuous long-term operation (more than 1 month). The superior FBB performance was attributed to the highly porous fibrous matrix that enabled the efficient mass transfer, cell immobilization, and continued growth and regeneration that are critical to maintaining a high density of viable and productive cell populations. The cells immobilized in the fibrous matrix had high viability (>85%) even though many of them were in growth arrest (G1/G0 phase) as indicated by their smaller cell size (<10 microm). Scanning electron microscopic studies of the cell-matrix showed that the high density of cells formed large clumps within the interstitial spaces of the fibrous matrix. Their close contact and interaction with each other might have contributed to their ability to survive well under adverse conditions such as low DO and low serum content in the medium. It was also found that the cells present inside the fibrous matrix had a higher viability and lower apoptosis than those present in the liquid suspension, indicating that the fibrous matrix had selectively retained healthy, nonapoptotic cells and dislodged apoptotic and dead cells; this also might have contributed to the stability of the long-term culture. This work demonstrated that the FBB originally developed for microbial fermentation also gave excellent results in achieving high cell density, productivity, and product concentrations, and should have a good potential for industrial animal cell culture applications.

Long-term Continuous Production of Monoclonal Antibody by Hybridoma Cells Immobilized in a Fibrous-Bed Bioreactor

The kinetics and long-term stability of continuous production of monoclonal antibody IgG2b by hybridoma HD-24 cells immobilized in a fibrous-bed bioreactor (FBB) were studied for a period of approximately 8 months. The cells were immobilized in the fibrous bed by surface attachment of cells and entrapment of large cell clumps in the void space of the fibrous matrix. A high viable cell density of 1.01 x 10(8)/ml was attained in the bioreactor, which was about 63 times higher than those in conventional T-flask and spinner flask cultures. The continuous FBB produced IgG at a concentration of approximately 0.5 g/l, with reactor productivity of approximately 7 mg/h.l, which was about 23 times higher than those from conventional T-flask and spinner flask cultures. The IgG concentration can be further increased to approximately 0.67 g/l by using higher feed (glucose and glutamine) concentrations and running the reactor at a recycle batch or fed-batch mode. The long-term performance of this bioreactor was also evaluated. For a period of 36 days monitored, the MAb produced in the continuous well-mixed bioreactor at 50 h retention time (0.02/h dilution rate) was maintained at a steady concentration level of approximately 0.3 g/l with less than 8% drift. At the end of the study, it was found that approximately 25% of the cells were strongly attached to the fiber surfaces and the other approximately 75% entrapped or weakly immobilized in the fibrous matrix. The strongly attached cells had a high viability of approximately 90%, compared to approximately 75% for cells weakly immobilized and only approximately 1.4% for freely suspended cells, suggesting that the fibrous matrix preferentially retained and protected the viable (productive) cells. The FBB thus was able to maintain its long-term productivity because nonviable and dead cells were continuously washed off from the fibrous matrix. The high MAb concentration and production rate and excellent stability for continuous long-term production obtained in this study compare favorably to other bioreactor studies reported in the literature. The reactor performance can be further improved by providing better pH and aeration controls at higher feed concentrations. The FBB is easy to operate and scale-up, and thus can be used economically for industrial production of MAb.

Calcium alginate immobilized hybridomas grown using a fluidized-bed perfusion system with a protein-free medium

Hybridoma SPO1 cells were immobilized in calcium alginate beads and were further grown in a fluidized-bed perfusion system with a protein-free medium. The presence of serum in the steps of entrapment was shown to be helpful for the preservation of cell viability. Each step during immobilization was investigated with respect to the extent of cell damage caused. The immobilization process using small beads caused a lower cell viability initially but allowed a higher rate of cell growth subsequently, compared to those in large beads. In a perfusion system for the continuous production of monoclonal antibodies (MAb), the viable cell density reached 2 x 10(7) cells per ml of beads with a viability of 40%. Compared with the cells in suspension culture, the immobilized SPO1 cells showed higher viable cell based specific rates of substrate uptake (glucose and glutamine) and of MAb production. A significant drop in the formation of lactate after the cell growth entered a steady state suggested a higher activity of the Tricarboxylic Acid Cycle in the cells when the cell density became high.

Immobilization of animal cells using photo-crosslinkable resin

A photo-crosslinkable resin, BIX12, was selected from among various photo-crosslinkable resins for the immobilization of animal cells. BIX12 had no cytotoxic effect on the growth of hybridoma cells and the production of monoclonal antibody, although other photo-crosslinkable resins had significant inhibitory effects. Using BIX12-alginate hybrid gel particles, hybridoma cells could grow in the resins and produce monoclonal antibody. For the continuous production of monoclonal antibody, perfusion culture using a fluidized-bed bioreactor with direct air bubbling was carried out. By this cultivation, monoclonal antibody could be produced stably for more than 50 d. A high viable cell density of more than 10 7 cells/ml-gel was attained, and the antibody productivity was improved 8.5-fold compared with conventional suspension culture using a spinner flask. Anchorage-dependent cells were also immobilized in the resin particles by three immobilization procedures. Among these procedures, porous BIX12 formed by adding gelatin powder provided good support strength and allowed the cells to grow on the surface inside of the support.

ChemInform Abstract: Continuous Production of Monoclonal Antibody by Hybridoma Cells Immobilized in Hardened Alginate Gel Particles

AbstractChemInform is a weekly Abstracting Service, delivering concise information at a glance that was extracted from about 100 leading journals. To access a ChemInform Abstract of an article which was published elsewhere, please select a “Full Text” option. The original article is trackable via the “References” option.

Continuous Production of Monoclonal Antibody by Hybridoma Cells Immobilized in Hardened Alginate Gel Particlesa

Continuous Production of Monoclonal Antibody by Hybridoma Cells Immobilized in Hardened Alginate Gel Particles^a

Effects of oxygen aeration on production of monoclonal antibody in immobilized hybridoma-cell bioreactor

Continuous production of monoclonal antibody by hybridoma cells immobilized with alginate and urethane polymer was done using a fluidized bed bioreactor with direct bubbling. Increasing the dilution rate did not affect the antibody production rate under aeration with air. By changing the aeration gas to oxygen instead of air, the antibody production rate was increased 2-fold. The monoclonal antibody could be produced continuously for more than 40 d.

Continuous production of monoclonal antibody with immobilized hybridoma cells in an expanded bed fermentor

Continuous production of monoclonal antibody was achieved in serum-free medium by hybridoma cells immobilized by calcium alginate. The cells were cultivated in an expanded bed fermentor under mild flow conditions which reduced destruction of the immobilized gel particles. Monoclonal antibody was produced continuously for more than 40 days.

Ceramic‐supported Hybridomas for Continuous Production of Monoclonal Antibodies

Description de la souche de la matrice et du reacteur. Methodes analytiques, observation des cellules immobilisees au microscope electronique