Continuous Dynamic Recrystallization Research Articles

The impact fretting corrosion behavior and damage mechanism of Inconel 690TT under different impact forces in high temperature pressurized water

The impact fretting corrosion of Inconel 690TT under different impact forces was investigated. The results indicated that there was a competitive relationship between formation of third body layer (TBL) and fragmentation of TBL caused by impact force. With the increase of impact forces, damage mechanism changed from adhesive wear to delamination wear, and crack initiation sites gradually shifted from TBL to internal oxidation zone in tribologically transformed structure (TTS) layer. Nanocrystalline boundaries and defects induced by impact force provided channels for internal oxidation. The formation mechanism of TTS was the combined effect of continuous dynamic recrystallization (cDRX) and twin-assisted cDRX.

Hot deformation behavior and microstructural evolutions of a Mg-Gd-Y-Zn-Zr alloy prepared by hot extrusion

The hot deformation behavior of extruded Mg-9.5Gd-4Y-2Zn-0.5Zr alloy was studied through hot compression tests conducted at deformation temperatures of 350–500 °C and strain rates of 0.001–1 s−1. Under most deformation conditions, the flow stress first reached a maximum before decreasing to a stable value, demonstrating characteristics of dynamic recrystallization (DRX). The constitutive equation of the alloy was established as ε.=1.03*1011sinh0.01287*σp2.422exp(−171150/RT) through calculations and derivation. The influences of the deformation temperature and strain rate on the microstructure and DRX of the alloy during the hot compression process were investigated using electron backscatter diffraction. It was found that at temperatures between 350 °C and 450 °C, the alloy texture exhibited multiple {0001} peak rings distributed around the normal axis of the compression direction. When the strain rate was 0.001 s−1, the average equivalent grain diameter significantly increased from 3.3 μm to 22.4 μm with the rise in deformation temperature, whereas when the deformation temperature was 450 °C, the volume fraction of DRX grains noticeably decreased from 87.6 % to 13.2 % with the increasing strain rate. Further research revealed that due to the restriction of strain rate on grain boundary migration, discontinuous dynamic recrystallization and continuous dynamic recrystallization were the predominant DRX mechanisms at low and high strain rates, respectively.

Hot deformation behavior and dynamic recrystallization mechanism of GH2132 superalloy

In order to study the hot deformation and dynamic recrystallization behavior of annealed GH2132 superalloy, this paper conducted hot compression tests of GH2132 superalloy at different temperatures (950°C–1150°C) and different strain rates (0.01/s–10/s) using Thermocmaster Z thermal simulation testing machine, and made an in-depth analysis of recrystallization behavior via electron backscattered diffraction (EBSD). The results indicate that the flow stresses of GH2132 alloy first increase and then decrease at high temperature, among which the curves present a more obvious flow softening at 10/s. Continuous dynamic recrystallization (CDRX) is dominant at high temperature and low strain rate, while discontinuous dynamic recrystallization (DDRX) plays the major role at low temperature and high strain rate. The type of recrystallization has a significant impact on the formation and volume fraction of twinning. In addition, high-temperature constitutive model, hot processing map, and an unified dynamic recrystallization kinetic model of GH2132 superalloy were established. Thus, the optimal range of hot working parameters was obtained. The research results provide guidance for determining the hot working process window of GH2132 superalloy.

Grain Microstructure in Friction-Stir-Welded Dissimilar Al/Mg Joints of Thin Sheets with/without Ultrasonic Vibration.

Electron backscattered diffraction (EBSD) characterization was conducted on the typical regions in friction-stir-welded dissimilar Al/Mg joints of 2 mm thick sheets with/without ultrasonic assistance. The effects of ultrasonic vibration (UV) on the grain size, recrystallization mechanisms, and degree of recrystallization on both sides of the Al-Mg bonding interface and the intermetallic compounds (IMCs) were investigated. It was found that on the Mg side of the weld nugget zone (WNZ), the primary dynamic recrystallization (DRX) mechanisms were discontinuous dynamic recrystallization (DDRX) and continuous dynamic recrystallization (CDRX), with geometric dynamic recrystallization (GDRX) playing a secondary role. On the Al side of the WNZ, CDRX was identified as the primary mechanism, with GDRX as a secondary contributor. While UV did not significantly alter the DRX mechanisms in either alloy within the WNZ, it promoted the aggregation and rearrangement of dislocations. This led to an increase in high-angle grain boundaries (HAGBs) and an enhanced degree of recrystallization in the welds. The average grain size in both the Al and Mg alloys of the WNZ followed a pattern of initially increasing and then decreasing along the thickness direction, reaching a maximum in the upper-middle part and a minimum at the bottom. The influence of UV on the average grain size in the WNZ was minimal, with only slight grain refinement observed, and the minimum refinement degree was only 0.9%. The Schmid factor (SF) on the WNZ and thermo-mechanically affected zone (TMAZ) boundary regions of the advancing side (AS) indicates that the application of UV increased the likelihood of basal slip and extension twinning in the crystal structure. In addition, UV reduced the thickness of IMCs and improved the strength of the Al-Mg bonding interface. These results suggest a higher probability of fracture along the TMAZ and WNZ boundary on the AS when UV was applied.

High-temperature hot deformation behavior and processing map of Ti-22Al-25Nb alloy

The high-temperature deformation behavior of the Ti-22Al-25Nb alloy was investigated by conducting hot compression experiments. A constitutive equation predicting the flow behavior of the Ti-22Al-25Nb alloy was established by analyzing its stress–strain curves. The strain-compensated constitutive equation effectively predicted the flow stress of the alloy with a correlation coefficient of 0.992 between the measured and predicted values and an average absolute relative error of 6.548 %. A hot processing map was obtained based on a dynamic material model. It demonstrated that the optimal processing region corresponded to the deformation temperatures of 1273–1353 K and strain rates of 0.001–0.01 s−1. Using electron backscatter diffraction data, thermal deformation mechanisms were elucidated under different deformation conditions within the safe region. The obtained results revealed that under the low temperature (T ≤ 1323 K) and low strain rate (ε̇ ≤ 1 s−1) conditions, continuous dynamic recrystallization and dynamic recovery (DRV) were the main thermal deformation mechanisms. Under the medium-to-high temperature (T ≥ 1323 K) and low strain rate (ε̇ ≤ 1 s−1) conditions, the main thermal deformation mechanisms were discontinuous dynamic recrystallization and DRV. At high strain rates (ε̇ ≥ 1 s−1), the primary thermaldeformation mechanism was DRV. The occurrence of discontinuous yielding in the alloy at high strain rates was related to the proliferation of mobile dislocations at grain boundaries.

Origins and optimization mechanisms of periodic microstructures in Al-Cu alloys fabricated by wire arc additive manufacturing combined with Interlayer Friction Stir Processing

Inter-layer Friction Stir Processing on Arc Additive Manufactured Components offers significant potential for performance enhancement, yet the homogenization of microstructures has become a challenge for industrial application. To address this, 2319 Al-Cu alloy components were fabricated through the Wire Arc Additive Manufacturing + Interlayer Friction Stir Processing (WAAM-IFSP)1 technique, and a systematic study was conducted on the effects of deformation degree, deformation temperature, and strain rate changes on the microstructural evolution, revealing three distinct periodic microstructures. An increase in deformation degree resulted in a uniform periodic microstructure, attributed to the more uniform internal deformation caused by the increased deformation degree. At a deformation degree of 24.1 %, higher strength and ductility were achieved, along with a notable bimodal grain structure (BGS). Further research indicated that this structure would distribute more widely within the matrix with increasing strain rate, aiding in further performance breakthroughs, ultimately reaching an ultimate tensile strength (UTS) of 404 MPa and an elongation (EL) of 32 %. However, imperfections in the process led to inhomogeneity in the structure. Focusing on the dynamic recrystallization (DRX) mechanisms during stirring can improve this phenomenon. The research revealed that the fine grains in the BGS were controlled by a synergy of dominant discontinuous dynamic recrystallization (DDRX) and auxiliary continuous dynamic recrystallization (CDRX) nucleation mechanisms. The findings are expected to provide a theoretical basis for the optimization of WAAM-IFSP processes and microstructural and performance regulation, which is crucial for enhancing the industrial application prospects of aluminum alloys.

Microstructure evolution after hot working and heat treatment in 6082 aluminum alloy manufactured by horizontal continuous casting

In this paper, 6082 aluminum alloy manufactured by horizontal continuous casting was subjected to high-temperature plastic deformation under 20–70 % deformation levels with following T6 heat treatment process. Microstructural and phase changes were investigated by light and scanning electron microscopy together with energy dispersive spectroscopy, while grain, grain boundary, dislocation and texture evolution was studied by electron-backscattered diffraction. The results are showing that continuous dynamic recrystallization processes are active during the hot working while influence of static recrystallization is significant only for highest deformation degrees. The abnormally coarse-grained microstructure does locally occur in the subsurface layer after the 70 % deformation and T6 heat treatment. Crystallographic texture components are gradually evolving from the various types (Goss, Brass, D) for the low deformations (up to 40 %) into fiber-type textures (α-fiber, γ-fiber or C2-fiber) for high deformations due to the inhomogeneity of plastic deformation. The formation of AlMnSi dispersoids, CSL-boundaries Σ25b and an increase in fraction of GND, MgSi and Fe-based intermetallic particles was observed during the phase transformation which promotes ongoing nucleation of recrystallization processes.

Microstructure evolution of pure magnesium based on dynamic recrystallization during ambient equal channel angular pressing

An as-extruded pure Mg bar was subjected to ambient equal channel angular pressing (ECAP) up to four passes. Recrystallization behavior of as-ECAPed samples was investigated by scanning electron microscope-electron back-scatter diffraction (SEM-EBSD). After four-pass ECAP, grain orientation was significantly changed and basal-oriented texture was formed with c-axes of most grains nearly parallel to transverse direction (TD). Dynamic recrystallization (DRX) shows obvious orientation dependence during ambient ECAP, with continuous dynamic recrystallization (CDRX) partly transforming into discontinuous dynamic recrystallization (DDRX) after the four-pass ECAP.

Unraveling dynamic recrystallization mechanisms in Ni-based wrought superalloy GH4698 through comprehensive EBSD analysis

A comprehensive examination of dynamic recrystallization (DRX) mechanisms in wrought superalloy GH4698 has been conducted, leveraging Gleeble thermal simulation experiments and advanced Electron Backscatter Diffraction (EBSD) characterization techniques. Rigorous analysis elucidates four distinct recrystallization processes: Discontinuous Dynamic Recrystallization (DDRX), instigated by strain-induced boundary migration (SIBM); Continuous Dynamic Recrystallization (CDRX), characterized by progressive lattice rotation; Particle Stimulated Nucleation (PSN), driven by the Zener pinning effect of MC-type carbides; and Twin-induced Dynamic Recrystallization (TDRX), facilitated by the interaction between twin boundaries and existing dislocations.

Effect of Trace Bismuth on Deformation Behavior of Ultrahigh-Purity Copper during Hot Compression

The effect of trace Bi impurities on the flow stress, microstructure evolution, and dynamic recrystallization (DRX) of the ultrahigh-purity copper was systematically investigated by a hot compression test at 600 °C. The results show that the peak stress of the ultrahigh-purity copper gradually decreases with increasing Bi content. Trace Bi impurities can refine the microstructure of ultrahigh-purity copper. However, the refinement effect of 50 wt ppm Bi is much more significant than that of 140 wt ppm Bi during the hot deformation. This effect is ascribed to the higher concentration of Bi at GBs, which induces severe GB cracks that reduces the driving force for the nucleation of DRX grains. In addition, the introduction of Bi inhibits the DRX of the ultrahigh-purity copper and transforms its DRX process from the discontinuous dynamic recrystallization (DDRX) to the coexistence of DDRX and continuous dynamic recrystallization (CDRX) mechanisms.

Relationship between grain structure evolution and tensile anisotropy in Al-Zn-Mg-Cu cylindrical part formed by additive friction stir deposition

The thick-walled Al-Zn-Mg-Cu cylindrical part was obtained by additive friction stir deposition, and the relationship between grain structure evolution and tensile anisotropy was investigated in detail. The intra-layer grains are significantly refined due to continuous dynamic recrystallization (CDRX), and the grains at the interface are further refined by 30%-45% due to geometric dynamic recrystallization (GDRX). The early cracking and ductility deterioration under Z direction loading are caused by strain localization due to coarse and fine grain distribution and pre-existing strain at the interface. The grain growth rates for specific orientations (Cube, P, Q, and Rotated Goss) are higher than average, and the mismatch in elastic modulus between these grown grains and the matrix results in ductility differences in the X and Y directions. Texture components and residual stresses affect yield strength in the X and Y directions. Meanwhile, dissolution of η/η' and the coarsening of the particles due to the thermal cycling effect leads to a decrease in the yield strength in the building direction. The average ultimate tensile strength (UTS) and elongation (El) of the part could reach 370 MPa and 20%, respectively. The tensile properties of the as-deposited Al-Zn-Mg-Cu cylindrical part are generally higher than those of melt-based additive manufacturing, but lower than those of the extruded and forged states due to the dissolution and coarsening of the strengthening precipitates during thermal cycling.

Unique grain refinement mechanism of graphene oxide reinforced high-temperature titanium alloy matrix composite

Grain refinement is an effective way to improve the comprehensive mechanical properties of titanium matrix composites. In this work, the strong grain refinement effect of GO on 600 ℃ high-temperature titanium alloy prepared by hot isostatic pressing was found. The refinement mechanism was studied by experimental analysis, first-principles calculation and cellular automaton simulation. The α grain size of the composite with 0.50wt.% GO decreased by 53.2% compared with the matrix alloy. The direct effect of GO on grain refinement was weak. GO introduced C and O as α-stable elements to increase α phase content, resulting in the solid solubility of Si decreasing and fine (TiZr)6Si3 particles precipitating. (TiZr)6Si3 particles prevented dislocation from moving to accelerate continuous dynamic recrystallization nucleation and pinned grain boundary to inhibit grain growth. The results of cellular automaton simulation show that the inhibitory efficiency of (TiZr)6Si3 on grain growth was 4.7 times that of GO. The unique mechanism that GO promoted silicide particles precipitation and indirectly refined grain provided a design route for novel titanium matrix composites synergistically strengthened by two-dimensional nanosheets, in-situ nanoparticles and grain refinement.

Dynamic recrystallization mechanisms and microstructure evolution of a novel Al-Zn-Mg-Cu-Zr alloy by isothermal compression

The dynamic recrystallization (DRX) behavior and microstructure evolution of a novel Al-Zn-Mg-Cu-Zr alloy was investigated by isothermal compression tests at temperature of 350–470 °C and strain rate of 0.0001–1 s−1. The results showed that the flow behavior revealed typical dynamic recovery (DRV) characteristics at a high strain rate (1 s−1), while exhibited a DRX shape when the strain rate decreased. The critical strains (εc) of the DRX decreased with the decrease of strain rate or the increase of deformation temperature. A low temperature was conductive to precipitation behavior, the coarse precipitates and dispersed Al3Zr particles would pin the dislocations and substructures, which inhibit the DRX process. The DRX mechanism of the Al-Zn-Mg-Cu-Zr alloy was dominated by continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX) during the hot deformation process, upon increasing the temperature and decreasing the strain rate, there was a transition point of DRX mechanism from DDRX to CDRX. Moreover, the linear relationship between the Zener-Hollomon (Z) parameter and DRX grain size was established for the further exploration of the transition of the dominant DRX mechanism.

High temperature electropalsticity in Aermet100 steel by decoupling electron wind effect

Aermet100 ultra-high strength steel (UHSS) is one of the highest strength-plasticity-matched metallic materials. It is widely used in critical load-bearing components in aerospace and weaponry. Compared to traditional forging processes, electropulsing assisted forming technology significantly enhances manufacturing efficiency and forming limits. Particularly in the forming of hard-to-deform materials into complex structures, it demonstrates significant application potential. However, quantitative studies on the decoupling of electron wind effects during high-temperature deformation and their impact on microstructural evolution, deformation mechanisms, and mechanical properties remain few reported, resulting in limiting the ability to select optimal process parameters in electropulsing assisted forming technology to precisely control material structure and properties. In this paper, the impact of varying degrees of electron wind effects on flow stress through high-temperature compression tests was investigated. The evolution of the microstructure was analyzed in conjunction with the thermodynamic and kinetic mechanisms of recrystallization. Moreover, the hitherto unexplained relationship between the activation of slip systems and texture components in Aermet100 UHSS is examined. Results indicate that with the enhancement of the electron wind effect, the flow stress of Aermet100 UHSS is reduced by 59.4 %. The electron wind effect not only reduces the activation energy for recrystallization but also enhances vacancy concentration, dislocation climb diffusion flux, and driving force, thus promoting continuous dynamic recrystallization. Furthermore, as the intensity of the electron wind effect increases to 0.85 Ew and above, S and Brass textures are observed for the first time. It is notable that the Dillamore texture, Brass texture, and S texture respectively activate specific slip systems (1‾ 10)[11 1‾], (0 1‾1‾)[11 1‾] and (110)[1‾ 11‾] during the hot deformation process of Aermet100 UHSS. This investigation sheds new insight into tailoring high temperature electroplasticity by regulating electron wind effects.

Crystallographic orientation and slip behavior of powder metallurgy Ti–6Al–4V via multi-directional forging

In this study, we present a microstructural and mechanical analysis of Ti–6Al–4V alloys processed by low-temperature multi-directional forging at 900 °C, achieving near-theoretical density (99.9%), with a tensile strength of 1070 MPa and elongation of 14.9%. The microstructure is defined by both continuous and discontinuous dynamic recrystallization occurring simultaneously, related to an increase in dislocation density. Significantly, this study reveals the interaction between crystallographic orientation and spheroidization during the forging process. Specifically, changes in crystallographic orientation include the asynchronous formation of new subgrains/grains, the disruption of the Burgers orientation relationship, and rotation around the <11 2‾ 0>axis, which not only increases the orientation differences between α lamellae but also enhances the spheroidization process. Moreover, our findings demonstrate that during deformation, the activation of basal and pyramidal slip systems is favored over prismatic slip, indicating that the forging process has enhanced slip activity. The average misorientation angle and the fraction of high-angle grain boundaries are quantified, providing a detailed characterization of the evolved microstructure. This study adopts a new perspective to examine the microstructural evolution during the multidirectional forging process in powder metallurgy, presenting findings that elucidate how multidirectional forging effectively controls.

The effect of pre-heat parameters and final-heat parameters on microstructure evolution and mechanical properties of Mg-Gd-Y-Zn-Zr alloy

In this study, an ultra-high strength Mg-13Gd-4Y–0Zn-0.5Zr (wt.%) alloy with tensile yield strength (TYS) of 456 MPa and ultimate tensile strength (UTS) of 486 MPa was prepared by using different pre-heat parameters and subsequent final-heat treatment combined with backward extrusion (BE) deformation process. It was shown that the pre-heat teratment could significantly enhance the UTS and TYS of the secondary backward extruded (BEed) alloy compared with none treatment. The reason was that the pre-heat treatment promoted the particle stimulated nucleation (PSN) mechanism and continuous dynamic recrystallization (CDRX), significantly increasing the fraction of dynamic recrystallization (DRX). The strengthening of the secondary BEed alloy was attributed to the unique microstructure characteristics: (I) the fine DRXed grains pinned by dynamic precipitates, (II) the dense dynamic precipitation phases, (III) the effect of the fine-grain strengthening. However, the overly densely distributed second phase, which increased the local dislocation density due to the narrower spacing, made it difficult to prevent crack propagation and caused premature fracture of the alloy. In addition, the subsequent final-heat treatment also facilitated the precipitation of the second phases of the secondary BEed alloys and brought in the ultra-high mechanical properties.

An efficient synergistic double-sided friction stir spot welding method: A case study on process optimization, interfacial characteristics and mechanical properties of 2198-T8 aluminum‑lithium alloy joints

Friction stir spot welding has important applications in the joining of thin metallic plates. However, the asymmetric thermomechanical action inherent in the single-sided friction stir spot welding inevitably generates the hook defect at the joint interface, and the defect deteriorates with the improvement of the interfacial metallurgical bonding, which causes the irreconcilable contradiction and significantly restricts the breakthrough of the process stability and welding efficiency. The synergistic double-sided probeless friction stir spot welding (SDP-FSSW) technology proposed in this study adopts a dual-axis synergistic control system, which introduces intense plastic deformation from both sides of the interface to form a wavy hook by accurate axial motion during the welding process. This innovative process solves the problem of hook warpage while realizing rapid metallurgical bonding and mechanical interlocking at the interface, thus obtaining AA2198-T8 aluminum‑lithium alloy spot joints with a tensile/shear strength exceeding 9kN in a short dwell time (0–3 s). Through response surface methodology, the optimal process parameters are identified, i.e. rotation speed of 603 rpm, dwell time of 3 s, and plunge depth of 0.26 mm, at which condition the average joint strength is 13.0 ± 0.5kN, a 47 % increase compared to an optimized joint of single-sided probeless friction stir spot welding (8.9kN). The optical microscope examination shows that the wavy hook can be adjusted by the rotation speed and the higher rotation speeds will make the wave disappear and produce an approximately straight interface. The fractographic analysis shows that the wavy hook can inhibit crack propagation and has good mechanical interlocking effect, but the flat hook at high rotation speeds leads to crack propagation directly along the interface, and the failure mode is changed from plug-pull fracture to interfacial fracture. Therefore, the joint strength at 1000 rpm is only 7.0kN, which decreases by about 47 % compared with the optimal strength. The electron backscattering diffraction analysis shows that continuous dynamic recrystallization occurs in the hook region and good metallurgical bonding is formed, and there are also some discontinuous dynamic recrystallized grains distributed between the large grains due to the larger strain rates and lower temperature at the interface during the SDP-FSSW process. It has been found that the wavy hook with good metallurgical bonding and mechanical interlocking can be introduced in spot welded joints by controlling the interface forming, which is a viable method to create high quality, efficient and reliable spot joints.

Microstructural evolution of GH4079 superalloy during hot deformation and heat treatment

Through hot compression and subsequent heat treatment experiments on GH4079 superalloy, the influence of different hot deformation and heat treatment conditions on the evolution of GH4079 superalloy microstructure was studied. The evolution of grains and γ′ phases under different thermomechanical conditions was investigated. The results indicate that at deformation temperatures above 1100 °C and strain rates ranging from 0.01 to 0.1 s−1, the primary mechanism of dynamic softening in the alloy is discontinuous dynamic recrystallization (DDRX). When the deformation temperature is below 1100 °C and strain rates range from 0.01 to 0.1 s−1, both continuous dynamic recrystallization (CDRX) and DDRX are the main dynamic softening mechanisms. Due to high strain energy accumulation, the samples deformed at lower temperatures (below 1100 °C) and then solution-treated at 1120 °C for 8 h exhibit significant increases in recrystallization volume fraction and recrystallization grain size. Conversely, the samples deformed at higher temperatures (above 1100 °C) and then solution-treated at 1120 °C for 8 h show minimal changes in recrystallization volume fraction and recrystallization grain size. After solution treatment at 1140 °C, the grain size of the alloy significantly increases. The samples deformed at higher strain rates exhibit the evolution of fine γ′ phases into elongated rod shapes during solution treatment, while larger γ′ phases undergo splitting processes.

A polycrystal plasticity-cellular automaton integrated modeling method for continuous dynamic recrystallization and its application to AA2196 alloy

Continuous dynamic recrystallization usually dominates the microstructural evolution in hot working of aluminum alloys, in which the high-angle grain boundaries of new grains mainly originate from the gradual increase in subgrain misorientation angles. In this work, an integrated computational method is proposed to simulate continuous dynamic recrystallization process of aluminum alloys by coupling three-dimensional cellular automaton and visco-plastic self-consistent models. The stress response, dislocation accumulation and recovery, and evolution of crystal orientations are computed in the context of polycrystal plasticity; the formation and rotation of subgrains, followed by stored energy and curvature-driven boundary migration, are captured and visualized by cellular automaton. The non-octahedral slip mode {110}<110> is additionally introduced to capture the 〈001〉 texture during hot compression. A universal cell topology deformation method is adopted to achieve an effective track of grain morphology evolution during plastic deformation. The proposed simulation framework is validated through simulating the isothermal uniaxial compression process of AA2196 alloy under different temperatures and strain rates. The orientation dependence of CDRX during compression is numerically reproduced by correlating the subgrain formation and rotation process with the activation state of slip systems. The simulated macroscopic flow stress, 3D microstructure and inherent microstructural characteristics such as subgrain size, subgrain boundaries and textures are in good agreement with the experimental results. The proposed method provides an effective and efficient tool for multi-scale simulation of hot forming process of aluminum alloys.

Superplastic behavior of a metastable β-type Ti alloy governed by grain size: Microstructure evolution and underlying deformation mechanism

The superplastic forming (SPF) technology has gained widespread adoption in the manufacturing of intricately shaped components made from Ti alloys with high dimensional accuracy due to its near net forming capabilities. It is crucial to systematically investigate the superplastic behavior in metastable β-type Ti alloys. However, the microstructure evolution and underlying superplastic deformation mechanism governed by grain size in these alloys remain unclear. In this study, three types of fine-grained (<10 μm) Ti-15V-3Cr-3Sn-3Al (Ti-15-3) alloys were obtained using friction stir processing (FSP), and tensile tests were conducted at temperature of 650 °C with strain rates ranging from 1 × 10−4 s−1 to 3 × 10−3 s−1. The deformation behavior of the coarse-grained (>3 μm) Ti-15-3 alloy can be described as quasi-superplastic rather than strictly superplastic. In this microstructure, plasticity is synergistically contributed by grain boundary sliding (GBS), continuous dynamic recrystallization (CDRX), and dynamic phase transformation (DPT). For the fine-grained (<3 μm) Ti-15-3 alloy, deformation enters into the superplastic region with GBS becoming the predominant deformation mechanism accompanied by DPT. Additionally, strain/stress promotes α phase precipitation from the β matrix, which inhibits grain growth and serves as a supplementary stress accommodation mechanism facilitating continuous operation of GBS and ultimately achieving exceptional superplasticity.