Contact Applications Research Articles

A Review of the Mineral Contact Angle Measurements and Applications in the Froth Flotation Process: Techniques and Influential Parameters, Part II

A Review of the Mineral Contact Angle Measurements and Applications in the Froth Flotation Process: Techniques and Influential Parameters, Part II

The effects of load conditions and structural parameters on fretting wear of annular flat in heavy-duty gas turbine

Heavy-duty gas turbine is the core equipment in energy and electricity systems. In the compressor of a heavy-duty gas turbine, the forces and torques are usually transmitted by the friction force of the annular flat contact interfaces between two adjacent discs. Aimed at the annular flat connection structure of the combined rotor in heavy-duty gas turbine, the distribution of fretting characteristics on the annular flat is analyzed. The wear depth was calculated on the contact interface based on the modified Archard's wear theory and finite element method. On the annular flat, the time-varying distributions of fretting characteristics with the progress of wear are investigated. The increase of fretting cycles increases the wear depth of the annular flat. Moreover, the effects of load conditions and disc geometrical parameters on the fretting characteristics are studied. The increase of tie rod preload force and transmitted torque will intensify the fretting wear on the annular flat. In addition, the decrease of the distance between the tie rod and the annular flat and the decrease of the width of the annular flat will exacerbate the fretting wear on the annular flat. A fretting wear experiment is conducted to verify the finite element model. The experimental results show the fitting curve of wear depth decreases from the inner radius to the outer radius, which aligns with the results obtained from the finite element simulation. Ultimately, the research of this paper will provide a reference for the design and engineering application of the annular flat contact interfaces.

Current-carrying low friction of hydrogenated amorphous carbon film

Hydrogenated amorphous carbon (a-C:H) films, which equip excellent low friction performance but insulated, are naturally excluded from sliding electrical contact applications. In this work, we achieved current-carrying low friction of a-C:H film by utilizing a triboelectric triggered ignition effect. Protective resistors were introduced in the circuit during run-in for effectively alleviating undesired arc ablation. A T-shape crystalline structure of graphite was observed in the wear track by transmission electron microscopy. The parallel-aligned graphite at the top surface induced low friction, while the vertical-aligned graphite in the interior formed efficient electron transmission channels. This study expands the selection range of current-carrying friction films and provides a novel insight for the design and regulation of current-carrying friction films.

Synthesis of Polyether Block Copolymers from 1,2-Epoxybutane and AEOn and Comparative Study of Physicochemical and Application Properties before and after the Synthesis.

In this study, the AEOnBO2 series of block polyoxybutenol ethers was synthesized by combining the AEO series of polyoxyethylene and preparing 1,2-epoxybutane (BO) block polyether using a semicontinuous method. The synthesis was performed by HPLC, MALDI-TOF-MS, FT-IR, and 1H NMR for structural analysis. The interaction parameters and surface tension of the systems before and after synthesis were studied using surface tension meter. The diffusion process of the systems before and after synthesis was studied using a KRÜSS bubble pressure tensiometer. The surfactant properties of AEOn and AEOnBO2 were evaluated by static and dynamic surface tension measurements. Each system formed a saturated adsorption layer in a water solution. The critical micelle concentration decreased dramatically after the introduction of BO groups, and the diffusion-adsorption process was consistent with the kinetic mechanism of hybrid diffusion. The microscopic self-assembled aggregate micellar behavior of all the systems was investigated using DLS, TEM, and SEM. The micellization process in all systems was spontaneous and enthalpy-driven, forming spherical aggregates, with the BO block reducing the aggregate diameter of the feedstock from 220.06 nm to about one-third of 80.02 nm. In addition, the dynamic contact angle, application, and physicochemical properties such as foaming and foam stabilization of each system were investigated. The contact angle was reduced from 70 to 50° at 120 s of stabilization, with a foam volume of 80 mL in all systems at 200 s. However, the AEOnBO2 showed accelerated foam decay at 500 s, with an increase in the contact angle from 70 to 50° at 200 s, but the AEOnBO2 showed accelerated foam decay at 500 s, with a decrease in the contact angle from 70 to 50° at 120 s stabilization. At 200 s, the foam volume of all systems was 80 mL, but AEOnBO2 showed an accelerated foam decay process, which shows that the BO group can accelerate the foam decay, and the comparative results show that the BO group can also optimize other application properties and physicochemical properties.

Revealing contaminants in China's recycled PET: Enabling safe food contact applications

The lack of data on chemical contamination in recycled polyethylene terephthalate (rPET) in food contact applications, impedes the legalization of rPET in food contact applications in China. This study offers a comprehensive analysis of contaminants in hot-washed rPET flakes, identifying 1011 compounds. While most substances were detected infrequently, some i.e., bis(2-ethylhexyl) phthalate and mineral oil aromatic hydrocarbons stood out for their relatively high average concentrations. Limonene emerged as the most frequently detected flavorants. Rare genotoxic compounds like safrole and diethyl sulfate were detected at low levels, emphasizing the importance of adopting a conservative evaluation approach. Molecular descriptor analysis guided the proposal of four new surrogates, i.e., dimethyl pentanedioate, 2-tridecanone, bis(2-ethylhexyl) terephthalate, and 2,2-dimethoxy-1,2-diphenylethanone, for challenge tests, aiming to better capture the chemical diversity of rPET contaminants. This research unveils the contamination profile of Chinese rPET and suggests adjustments to evaluation protocols, potentially facilitating its high-value applications and minimizing potential harms.

Impacts of washing and deodorization treatment on packaging-sourced post-consumer polypropylene

AbstractEmerging legal requirements will likely considerably heighten demand for high-quality recycled raw materials for e.g., packaging and automotive applications; key EU legislation mandates recycling as the future end-of-life option for municipal solid plastic waste. Yet recycled plastic use remains low due to safety concerns, undesirable aesthetic, olfactory, and mechanical properties, mainly attributable to contaminants present in recyclates. Advanced treatment options for recovered polypropylene (PP) packaging and the impact of such treatments on the polymer are currently poorly documented. We investigated the effectiveness of hot/cold washing and hot air devolatilization treatments in removing volatile substances from residential post-consumer PP plastic waste to improve its scope of application and value and to assess possible side effects on mechanical and processing parameters. Cold- and hot-washed recyclates exhibited similar contaminant levels and most substances were removed within 7 h. The recycling procedure had no adverse effects on mechanical or processing parameters although reprocessing caused polymer degradation, indicated by decreasing viscosity, elongation at break, and tensile strength. Washing and hot air devolatilization treatment of plastic wastes improve their scope of application and value by enhancing mechanical properties and considerably reducing the amounts of odorous substances, but is often not suited to high-quality applications, such as packaging. The dominance of packaging waste and strict legislation on food-grade recyclate applications will make widespread recyclate use challenging since it represents the primary use of plastic. Recyclate must consequently be extensively utilized in non-food contact applications until advances in waste sorting, washing, and devolatilization yield less contaminated recyclates with improved properties.

Copper-Nickel/SiC composites for applications on contact electrodes

Novel copper-nickel matrix composites reinforced with silicon carbide (SiC) micro particles for metal contact applications were manufactured by powder metallurgy technology and were experimentally characterized. Cu and Cu alloys are commonly used as metal contact for either vacuum, oil, or SF6 in low-voltage circuit breaker devices, but their application in environments with the presence of oxygen is limited due to their tendency to form high-resistance copper oxides. Thus, the addition of Ni as an alloying element provides resistance to both humidity and several corrosive environments and increases the composites' hardness, mechanical strength, and wear resistance. Moreover, SiC was chosen due to its contribution to mechanical strength, mouldability, low production cost, and non-reactive nature at ordinary temperatures. Here, three SiC particle size distributions were considered, and it was found that the composites' physical properties are also dependent on the ceramic loading. After evaluating these properties, two specific SiC concentrations were potentially considered for electrode applications: 10 wt% and 20 wt%. The obtained hardness values are in the range of 55 – 65 HR30T which guarantees the necessary strength without detriment of the contact area whereas the welding is minimized. In addition to a homogeneous particle distribution in the solid material, specific wear resistance of ∼10-5 mm3N-1m-1 and electrical conductivities of ∼20 %IACS were obtained. Considering these parameters, Cu-Ni/SiC composites' performance is not compromised compared to commercial Ag/WC materials commonly used in metal contact applications.

Three-Point Contact Repair Technique for Partial Subscapularis Tears Using U-Stitch and Cow Hitch Knot Loaded on a Single Knotless Anchor: Simple, Reliable and Quick Method

The importance of repairing the subscapularis tendon to facilitate restoration of the rotator cuff force couple is obvious. However, identifying and repairing subscapularis tears can be challenging for surgeons. In this technical note, we present our preferred surgical method for Lafosse type 1, 2, and 3 and Yoo and Rhee type 1-2A and 2B subscapularis tears, providing a 3-point suture contact achieved with FiberTape (Arthrex) and knotless anchors. In this technique, fiber suture is placed into the superolateral edge of the subscapularis tendon as a traction stitch (cow hitch knot). Second, the FiberTape is passed through the medial upper and lower parts of the tendon, just perpendicular to the fibers, using a suture passer. The FiberTape’s free ends remain on the tendon’s anterior side, shaping a U form. The U-shaped FiberTape and traction suture are loaded to a knotless anchor and placed on the footprint area. This creates a 3-point contact between the FiberTape U-suture and the cow hitch knot on the area. We believe that this technique provides fast and reliable fixation due to its 3-point contact application and simplicity.

Contact damage response of alumina-based layered architectures under different loading configurations

Hertzian contact damage upon spherical indentation is investigated in alumina-based ceramics designed with embedded textured compressive layers. The effect of the location of the embedded layer and the testing configuration (parallel or normal to the layer orientation) on the sub-surface damage evolution is explored. An acoustic emission system for crack detection and post-mortem cross sectioning are employed to evaluate the onset and extension of damage in the different samples. Distinct acoustic signals detected at different contact loads are correlated with the onset of the ring crack, cone crack propagation and quasi-plastic deformation within the textured layer. The distinct damage mechanisms are influenced by the location of the embedded textured compressive layer and the loading orientation with respect to the layers. The design of layered ceramics for contact applications should consider the loading orientation as well as the contact stress field with respect to the “protective” layer to enhance damage tolerance.

Plasma Spraying NiCoCrAlY-Cr2O3-AgMo Coatings: Fabrication and Tribological Mechanisms

The increasing demand for high-performance aircraft engines has led to a greater emphasis being placed on advanced sealing coating technologies. Developing long-life, self-lubricating, and wear-resistant coatings is of significant research value. This study focuses on the fabrication of a novel self-lubricating and wear-resistant NiCoCrAlY-Cr2O3-AgMo composite coating. This coating was deposited onto a GH4169 substrate utilizing plasma spraying. Scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS) and X-ray diffraction (XRD) methods were employed to characterize the elemental composition and microstructure of the fabricated NiCoCrAlY-Cr2O3-AgMo composite coating. Microhardness measurements across the coating cross-section indicated a gradual increase in hardness from the GH4169 substrate to the NiCoCrAlY-Cr2O3-AgMo coating. The average hardness of the GH4169 substrate was 413.92 HV0.2, while the CoNiCrAlY bonding layer region exhibited an average hardness of 467.60 HV0.2. The NiCoCrAlY-Cr2O3-AgMo coating itself demonstrated an average microhardness of 643.22 HV0.2. Room temperature friction tests indicated that the average coefficient of friction (COF) of the GH4169 substrate was 0.665. In contrast, the NiCoCrAlY-Cr2O3-AgMo coating exhibited a significantly lower average COF of 0.16, representing a 75.94% reduction compared to the uncoated GH4169 substrate. High-temperature friction tests were conducted at 400 °C, 500 °C, and 600 °C, indicating average COF values of 0.438, 0.410, and 0.268, respectively, for the NiCoCrAlY-Cr2O3-AgMo coating. Specifically, at 600 °C, the formation of a lubricious NiMoO4 tribofilm on the coating surface was observed. This tribofilm effectively reduced the wear rate of the GH605 pin to 2.78 × 10−6 mm3/N·m, highlighting the potential of the NiCoCrAlY-Cr2O3-AgMo coating to reduce wear in high-temperature sliding contact applications.

Determination of Diffusion Coefficients of Bisphenol A (BPA) in Polyethylene Terephthalate (PET) to Estimate Migration of BPA from Recycled PET into Foods

Bisphenol A (BPA) is a known substance that is found in food contact materials as an intentionally added as well as a non-intentionally added substance. Traces of BPA were found as a non-intentionally added substance in recycled PET (rPET). In 2023, the EFSA proposed a new TDI of 0.0002 µg/kg bw/d, which is lower than the previous (temporary) TDI of 4 µg/kg bw/d by a factor of 20,000. The TDI of 0.0002 µg/kg bw/d would translate for a default 60 kg person eating one kilogram of food into a migration limit of 0.012 µg/kg in the food. This very low migration limit is a challenge to measuring BPA levels in food. A solution is to use migration modeling to establish maximum concentrations in rPET for different food contact applications. Precise diffusion coefficients for BPA in PET were determined within this study by use of migration kinetics. In June 2024, the European Commission proposed a new migration threshold limit for BPA of 1 µg/kg, which should be understood as a detection limit. From the results of this study, it can be concluded that a BPA concentration in the PET bottle wall of 297 mg/kg (3% acetic acid), 255 mg/kg (10% ethanol), and 192 mg/kg (20% ethanol) after storage for 365 d at 25 °C is in compliance with the migration threshold limit of 1 µg/kg. These maximum concentrations are far above the measured BPA concentrations on rPET bottles in Europe between 2019 and 2023. Therefore, the new proposed migration threshold limit for BPA cannot be exceeded.

Synergistic-strengthening strategy induce excellent electrical and mechanical properties in Cu/AlCrCuFeNi2.5 composites

A novel high-strength conductive Cu-based composite, utilizing AlCrCuFeNi2.5 (Ni2.5) high-entropy alloy particles as the reinforcing phase, is synthesized through a combination of ball milling and spark plasma sintering processes. The mechanical and electrical properties of the composites are optimized by adjusting the composition. Under the synergistic effect of multiple strengthening mechanisms, the fabricated Cu-20 wt% Ni2.5 composites achieve an exceptional compressive strength of 920 MPa while maintaining an electrical conductivity of 44.3 % IACS (International Standard Copper Standard). The establishment of robust interface bonding between Ni2.5 reinforcement and Cu matrix stands as a pivotal assurance for the holistic performance of composites. Ni2.5 HEA is distinguished by good plasticity and high strength compared with traditional brittle reinforcements. An insight into the differences brought about by the distinctive dual-phase structure in terms of interfacial bonding, crack propagation, and performance is provided. It paves the way for selecting and projecting the composites for electrical contact applications, ushering in a realm of fresh possibilities.

Identification and health risk assessment of volatile and semi-volatile migrants along with chemical elements in food contact water-borne coating paper

Water-borne coating paper, with its food contact potential, raises concerns due to unknown contaminants. Herein, the presence and migration of volatile and semi-volatile compounds, along with chemical elements from two water-borne coating paperboards were investigated using 4 % acetic acid, 50 % ethanol, and 95 % ethanol, while also evaluating associated health risks. The results showed that the overall migration to 95 % ethanol from both papers indicated the non-compliance with the reference limit of 10 mg/dm2. Utilizing an optimized direct immersion-solid-phase microextraction coupled to gas chromatography-mass spectrometry method, a total of 66 migrants were identified, among which 16 and 7 were classified as Cramer Ⅲ and Cramer Ⅱ, respectively, linked to coating and paper raw materials. Additionally, 28 chemical elements released from papers were analysed using inductively coupled plasma mass spectrometry, where higher levels of elements (i.e., Na, K) were observed in the migration of 4 % acetic acid, potentially from additives or raw materials used in papermaking processes. More importantly, health risk assessment based on the Threshold of Toxicological Concern approach or worst-case dietary intake assumption indicated that, the estimated daily intake of most migrants and chemical elements through human exposure fell below toxicological reference values. However, certain migrants (e.g., 2-ethylhexyl acrylate, methyl benzoate, phenanthrene, and longifolene) exhibited concerning migration levels in 50 % ethanol and 95 % ethanol that exceed their safety thresholds and may pose health risks. Overall, understanding the migration and potential risk of migrants are imperative for ensuring the safety of using commercially available water-borne coating paper in food contact applications.

A polyester- stainless steel based smart wristband sensor for skin temperature monitoring

This study presents the development and characterization of a novel textile-based wristband sensor for continuous temperature monitoring. The sensor, woven with a blend of polyester-stainless steel and polyester-cotton yarns, exhibited high sensitivity (0.0315/°C) and a rapid response time (∼35 sec). Stainless steel was selected for its excellent electrical conductivity and biocompatibility, crucial for accurate and safe skin contact applications, while polyester and cotton contribute its lightweight, breathable, and durable properties, ensuring prolonged comfort and wearability. Through systematic testing and optimization, the sensor’s sensitivity was fine-tuned by adjusting the number and length of conductive yarns. The study also introduced a theoretical resistance equivalent model, comparing its theoretical sensitivity with experimental findings. The sensor, lightweight and cost-effective, proved comfortable during 8–10 h of continuous wear. This study addresses challenges faced by existing textile temperature sensors and offers a reliable alternative with high linearity, repeatability, and suitability for individuals with sensitive skin.

Fish Scales for Wearable Patches: Tailoring Films Assembled From Fish Waste Gelatin, Carbon Dots and Chitin Nanocrystals

AbstractThe properties of gelatin and collagen extracted from fishery wastes, specifically from mullet (Mugil Cephalus) scales, are modified with the aim to achieve biocompatible films with tunable characteristics to design sustainable UV protection solutions in the healthcare sector. Different additives are used to the scope including plasticizers, cross‐linkers, surfactants and optical modifiers. Carbon dots (CDs) obtained from seabass (Dicentrarchus labrax) scales combined with polysorbate‐20 (PS) as a dispersant agent, enable the fabrication of materials capable of blocking UV radiation almost completely, a crucial feature for dermal contact applications. The addition of hydrophobic surfactants and crosslinkers as citric acid, chitosan and surface deacetylated chitin nanocrystals (CsNCs) allowed to modulate the water adsorption of the films in the range 3–30% and to reach a twofold and 4.5‐fold increase of tensile strength and elastic modulus, respectively, as compared to the neat gelatin film. Moreover, film thickness is shown to be another adjustable parameter to enhance optic, mechanical, and permeation properties: the higher the thickness, the greater the UV‐blocking properties, elongation‐at‐break and water vapor permeability, leading to films with attractive characteristics as wearable patches.

'The Garlic Gambit': an alternative strategy for controlling vine weevil (Otiorhynchus sulcatus F.; Coleoptera: Curculionidae).

Plant protection products derived from plant material are proposed to be a sustainable alternative to conventional synthetic chemical pesticides. This study determines the efficacy of a commercially available bioinsecticide based on garlic (Allium sativum L.; Asparagales: Amaryllidaceae) extract against vine weevil (Otiorhynchus sulcatus F.; Coleoptera: Curculionidae) eggs and larvae in contact, fumigation and a combination of contact and fumigation bioassays under laboratory conditions. Results showed that garlic significantly reduced egg hatch rate compared to the control group when applied as a fumigant. Similarly, the egg hatch rate was reduced compared to the control group when garlic was applied as combined contact and fumigant applications. No effect was observed when the garlic product was applied as a contact application. The bioinsecticide significantly reduced larval survival when either contact or fumigant applications were used. A combined contact and fumigant effect was shown also when vine weevil eggs were exposed to the bioinsecticide for 30 days in plastic containers containing growing media. The number of larvae recovered after this period was significantly reduced compared to the control group. This study demonstrates the potential of garlic-based bioinsecticides, such as Pitcher GR, for vine weevil control. Further studies are, however, needed to determine the efficacy of such bioinsecticides under field conditions and investigate how these products can be most effectively used as a part of a wider vine weevil integrated pest management program.

Screening and safety assessment of migrating substances released from biodegradable packaging materials into milk

Biodegradable polymeric packaging materials are being studied for their potential to replace traditional petroleum-based ones for food contact applications. However, potential safety concerns associated with the utilization of these biodegradable polymers have not been studied in detail. In this study, we conducted non-targeted screening and migration studies on two types of biodegradable milk packaging materials, which were composed of a mixture of polylactic acid (PLA), poly(butylene adipate-co-terephthalate) (PBAT), polybutylene succinate (PBS), and cellulose. In particular, we monitored the transfer of migrating substances from the packaging materials into a food simulant (50% ethanol) and into a real food (fat free and whole milk). A screening study identified seven compounds in the biodegradable packaging bags, including degradation products of antioxidants, lubricants, and plasticizers such as triethylene glycol, diethyl succinate, glycerin, 2,4-di-tert-butylphenol, and 13-docosenamide were identified. The migration studies indicated that the types and amounts of migrating substances transferred into the real food were appreciably lower than those transferred into the food simulant. Most of the detected migrating substances were below the levels established in the European Union regulations. However, the triethylene glycol levels (68-144 mg/kg) in the food simulant exceeded the limits (60 mg/kg) for one of the packaging materials tested. A safety assessment suggested that there is a low level of safety risk associated with one of the biodegradable packaging materials. This study provides important insights into the safety of biodegradable packaging materials that might be used in the food industry.

Investigation of the Effectiveness of Barrier Layers to Inhibit Mutagenic Effects of Recycled LDPE Films, Using a Miniaturized Ames Test and GC-MS Analysis

To fulfil the European Green Deal targets and implement a circular economy, there is an urgent need to increase recycling rates of packaging materials. However, before recycled materials can be used in food contact applications, they must meet high safety standards. According to the European Food Safety Authority (EFSA), a worst-case scenario must be applied and unknown substances must be evaluated as being potentially genotoxic. The Ames test, which detects direct DNA-reactive effects, together with chromatographic analysis is very promising to complement risk assessment. This study aims to evaluate the effectiveness of functional barriers in ten different samples, including virgin and recycled LDPE foils. FT-IR analysis did not show major differences between virgin and recycled films. Light microscopy revealed differences in quality and an increased number of particles. GC-MS analysis detected and quantified 35 substances, including eight unknowns. Using a miniaturized version of the Ames test, four of ten samples tested positive in two individual migrates up to a dilution of 12.5%. All virgin LDPE materials tested negative; however, recycled material F showed an increased mutagenic activity, with an n-fold induction up to 28. Samples with functional barriers lowered migration and reduced mutagenicity. Nonetheless, further investigations are needed to identify possible sources of contamination.

Peach Gum Polysaccharide as an Additive for Thermoplastic Starch to Produce Water-Soluble Films

Thermoplastic starch (TPS) has gained considerable attention during the last few years in developing starch-based biodegradable food packaging materials or edible coatings due to its high availability and low cost. TPS is manufactured from starch plasticized with food-grade plasticizers, making it suitable for food contact applications. In addition, TPS is bio-based and biodegradable, which, from an environmental perspective, closes the circle of the circular economy. However, the industrial application of TPS is somewhat limited due to its poor mechanical performance and low water resistance. However, the low water resistance could increase the water sensitivity of TPS, which could be advantageous for coating application or food encapsulation. The present work aims to tailor the water sensitivity of TPS by adding peach gum polysaccharide to obtain water-soluble films. With this aim, peach gum polysaccharide (PGP) was extracted from peach gum (PG) using the thermal hydrolysis method. Films of TPS-PG and TPS-PGP were prepared and characterized by their water sensitivity and mechanical, microstructural, and thermal properties. The results show that PGP allows the obtaining of films with water sensitivities higher than 70% but also improves TPS elongation at break, making the material more suitable for application as film.

Construct functional PEGDA/CSMA/CuII photosensitive ink for SLA 3D printing of blood contact appliance

Stereolithography (SLA) is an emerging technology in three-dimensional printing that has garnered significant attention in the biomedical field due to its high printing fidelity, good biocompatibility, and high spatial resolution. Polyethylene glycol diacrylate (PEGDA) is commonly used as a photosensitive printing ink in SLA, and it possesses excellent biocompatibility, photosensitivity, processability, water solubility, and biomechanical tunability. Additionally, PEGDA exhibits unique anti-protein, platelet, and cell adhesion possibilities, making it a promising material for blood contact applications. However, cross-linking PEGDA using chain growth photopolymerization results in a high concentration of reactive functional groups, leading to high print volume shrinkage, decreased precision of the finished product, warping, deformation, and cracking. This study introduces a chemically modified methacryloylated chitosan (CSMA) as a cross-linking agent into the PEGDA ink. This strategy effectively reduces the volume shrinkage of the ink and imparts antimicrobial properties to the final product. The dual anticoagulation properties of PEGDA were achieved by loading divalent copper ion (CuII) into the ink, which better addresses the antimicrobial and anticoagulant needs in the physiological environment of blood. The results show that SLA printable inks based on PEGDA/CSMA/CuII have low swelling, high print fidelity, high stability, and good cell compatibility. Furthermore, by verifying the functionality of PEGDA/CSMA/CuII, the research shows that the bioprinting ink exhibits excellent antibacterial and anticoagulant properties, making it a promising material candidate for SLA 3D printing of blood purification, central venous catheter, and other semi-implanted blood materials. This study provides new ideas for developing multifunctional photosensitive inks in biomedical engineering.