O2 Concentration Research Articles

Efficient estimation of gas exchange and respiration kinetics in apple using pathlength-resolved GASMAS

Optimization of controlled atmosphere (CA) storage of pome fruit crucially depends on understanding of respiratory gas exchange. Different fruit properties are involved in describing gas transfer and respiration kinetics, which can vary between cultivars, fruit batches and individual fruit. Determination of these properties currently requires a combination of different time-consuming techniques and data analysis procedures. This study introduces a more efficient single method for O2 gas exchange characterization of fruit based on the non-destructive pathlength-resolved GASMAS (gas in scattering media absorption spectroscopy) technique. GASMAS was used to measure the absolute intercellular O2 concentration in fruit of different apple cultivars (Malus x domestica Borkh.) with distinct porosity including 'Jonagold', 'Braeburn', and 'Nicoter'. To resolve the ambiguity between variation in pathlength and O2 concentration inherent to GASMAS, the pathlength travelled through pores cavities was quantified through a second GASMAS measurement at the absorption line of H2O vapour. Dynamic experiments were then performed in which the fruit was subjected to varying external O2 concentrations while measuring the internal O2 response. The observed dynamic profiles of external and internal O2 concentration were fitted with a lumped -respiration model to estimate the effective mass transfer coefficient, maximum respiration rate and Michaelis Menten constant of intact fruit. The model showed a good fit (R2>0.95) with the measured data and reliable estimates for the model parameters. The proposed method provides a novel and more efficient way to estimate the gas exchange properties of fruit that are essential for optimizing CA storage conditions. Future challenges for the proposed method are with applications to other gasses such as CO2 and ethylene.

On the evolution and formation of discharge morphology in pulsed dielectric barrier discharge

The discharge morphology of pulsed dielectric barrier discharge (PDBD) plays important roles in its applications. Here, we systematically investigated the effects of the voltage amplitude, discharge gap, and O2 content on the PDBD morphology, and revealed the possible underlying mechanism of the U-shaped formation. First, the morphological evolution under different conditions was recorded. A unique U-shaped region appears in the middle edge region when the gap is larger than 2 mm, while the entire discharge region remains columnar under a 2 mm gap in He PDBD. The width of the discharge and the U-shaped region increase with the increase in voltage, and decrease with the increase of the gap and O2 content. To explain this phenomenon, a two-dimensional symmetric model was developed to simulate the spatiotemporal evolution of different species and calculate the electric thrust. The discharge morphology evolution directly corresponds to the excited-state atomic reduction process. The electric thrust on the charged particles mainly determines the reaction region and strongly influences the U-shaped formation. When the gap is less than 2 mm, the electric thrust is homogeneous throughout the entire region, resulting in a columnar shape. However, when the gap is larger than 2 mm or O2 is added, the electric thrust in the edge region becomes greater than that in the middle, leading to the U-shaped formation. Furthermore, in He PDBD, the charged particles generating electric thrust are mainly electrons and helium ions, while in He/O2 PDBD those that generate electric thrust at the outer edge of the electrode surface are mainly various oxygen-containing ions.

Enhanced hydrodechlorination of 4-chlorophenol through carboxymethylcellulose-modified Pd/Fe nanosuspension synthesized by one-step methods

Palladized iron (Pd/Fe) represents one of the most common modification strategies for nanoscale zero-valent iron (nZVI). Most studies prepared Pd/Fe by reducing iron salts and depositing Pd species on the surface of pre-synthesized nZVI, which can be called the two-step method. In this study, we proposed a one-step method to obtain Pd/Fe by the concurrent formation of Fe0 and Pd0 and investigated the effects of these two methods on 4-chlorophenol (4-CP) removal, with carboxymethylcellulose (CMC) coated as a surface modifier. Results indicated that the one-step method, not only streamlined the synthesis process, but also Pd/Fe-CMCone-step, synthesized by it, exhibited a higher 4-CP removal rate (97.9%) compared to the two-step method material Pd/Fe-CMCtwo-step (82.4%). Electrochemical analyses revealed that the enhanced activity of Pd/Fe-CMCone-step was attributed to its higher electron transfer efficiency and more available reactive species, active adsorbed hydrogen species (Hads*). Detection of intermediate products demonstrated that, under the influence of Pd/Fe-CMCone-step, the main route of 4-CP was through hydrodechlorination (HDC) to form phenol and H* was the main active specie, supported by EPR tests, quenching experiments and product analysis. Additionally, the effects of initial 4-CP concentration, initial pH, O2 concentration, anions such as Cl−, SO42−, HCO3−, and humic acid (HA) were also investigated. In conclusion, the results of this study suggest that Pd/Fe-CMCone-step, synthesized through the one-step method, is a convenient and efficient nZVI-modifying material suitable for the HDC of chlorinated organic compounds.

Spatial, Seasonal, and Diel Controls of Nitrogen‐Carbon‐Oxygen Cycling During Lake‐Water Infiltration to an Aquifer

AbstractMany freshwater lakes are groundwater flow‐through systems. Although lakes commonly are considered to be sinks for nitrogen inputs, relatively little is known about carbon and nitrogen export from lakes to groundwater. The current study focused on lake‐bottom biogeochemical processes accompanying the transport of nitrogen, dissolved oxygen (O2), and dissolved organic carbon (DOC) during lake‐water recharge from a groundwater flow‐through lake. Lake‐water and porewater (15–100 cm below lakebed) samples were collected along transects within the lake downwelling zone. Infiltrating porewater O2 and DOC concentrations decreased with depth while nitrate (NO3−) concentrations increased, indicating nitrification of organic matter within the profiles. The depth of NO3− production and transport was seasonally dependent. In winter, NO3− and O2 were exported beyond 100‐cm depth; whereas in summer, shallow nitrification zones were underlain by deeper NO3− reduction zones, and diel patterns of O2 and NO3− penetration depths were observed. Microbial community compositions and stable isotope profiles (δ15N[NO3−], δ18O[NO3−], δ18O[O2]) were consistent with apparent C–N–O reaction stoichiometries indicating O2 reduction and nitrification in shallower porewater, followed by varying NO3− reduction at depth. Maximum porewater NO3− concentrations (∼10–20 μM) were limited by infiltrating O2 concentrations and C/N ratios of reacting organic matter. Lake‐water level variations caused changes in shoreline position and porewater velocities, while variations in lake‐water temperature, DOC, and O2 contributed to changes in reaction rates and depth of O2 and NO3− penetration into the lakebed. The quality of groundwater recharged by lake water reflected temporally and spatially varying physical and biogeochemical processes in the sediment porewater.

Retrofit and application of pulverized coal burners with LNG and oxygen ignition in utility boiler under ultra-low load operation

An oxygen-rich and low NOx burner integrated with liquefied natural gas (LNG) was proposed to address unstable combustion and high NOx emissions from a 330 MW subcritical boiler under ultra-low load operation in China. To assess the effectiveness of the retrofit, Chemkin and Fluent softwares were utilized to construct a new NOx model and calculate NOx generation, based on the combustion of pulverized coal gas and LNG. Further, an eddy dissipation concept (EDC) model, which can reflect detailed chemical reactions, was applied to calculate gas-phase reactions in the furnace. The results showed that when performing the deep peak shaving after the retrofit, the combustion in the furnace was stable under 50% or more load, and NOx emission level at the furnace outlet was lower than 350 mg/m3 (6% O2 content, dry basis). Under 25% load, the oxygen-rich burner integrated with LNG was applied, and the pulverized coal flow entered the furnace in a state of high-intensity combustion, which effectively promoted the stability of combustion in the furnace. The reductive combustion state with reductive free radicals generated by LNG decomposition inhibited NOx formation. Consequently, NOx emissions from the furnace outlet decreased from 380 mg/m3 to 316 mg/m3.

Hyperoxia and brain: the link between necessity and injury from a molecular perspective.

Oxygen (O2) supplementation is commonly used to treat hypoxia in patients with respiratory failure. However, indiscriminate use can lead to hyperoxia, a condition detrimental to living tissues, particularly the brain. The brain is sensitive to reactive oxygen species (ROS) and inflammation caused by high concentrations of O2, which can result in brain damage and mitochondrial dysfunction, common features of neurodegenerative disorders. Hyperoxia leads to increased production of ROS, causing oxidative stress, an imbalance between oxidants and antioxidants, which can damage tissues. The brain is particularly vulnerable to oxidative stress due to its lipid composition, high O2 consumption rate, and low levels of antioxidant enzymes. Moreover, hyperoxia can cause vasoconstriction and decreased O2 supply to the brain, posing a challenge to redox balance and neurodegenerative processes. Studies have shown that the severity of hyperoxia-induced brain damage varies with inspired O2 concentration and duration of exposure. Therefore, careful evaluation of the balance between benefits and risks of O2 supplementation, especially in clinical settings, is crucial.

Statistical analysis on branching characteristics of positive streamer discharges in N2–O2 mixtures

Streamers are fast-propagating ionization channels that can usually branch and form complex tree-like structures in dielectric media. In this paper, we perform experiments on positive streamers in different N2–O2 mixtures under varying conditions including voltage, pressure, and electrode geometry, with at least 125 discharge images captured for each condition. We present a statistical analysis on streamer branching characteristics from 3D models that are reconstructed by stereoscopic stroboscopic images and our dedicated semi-automatic 3D reconstruction method.We found that by varying the concentration of O2, the morphology and branching characteristics are greatly changed. Specifically, the average branching angle decrease significantly from 90∘ in air to 66∘ in 1% O2, suggesting that photoionization plays an important role in streamer branching. The branching angles in our work are generally larger than previously reported results due to the resolved 3D structures of discharges by our method. A linear relation between the streamer diameter ratio and the branching direction difference of two daughter branches is found, which intersects the vertical axis almost at unity. It is also found that the average branching angles, streamer velocities and diameters increase as the voltage increases. This is again attributed to stronger photoionization effect under higher voltages. The velocities and diameters are similar at different pressures but at the same reduced electric field. The average branching angle decreases from 90∘ at 133 mbar to 79∘ at 200 mbar. This suggests that stochastic fluctuations become dominant over photoionization effect at higher pressures.

Shaded streams with permeable watersheds provide naturally resilient fish habitat refugia during heatwaves

AbstractStreamflow, dissolved oxygen, and water temperature underpin stream fish habitat suitability, so climate change could cause widespread habitat deterioration. Identifying stream characteristics that mediate habitat resilience to heatwaves will allow conservation effort prioritisation. Here, a set of readily applied metrics were used to assess hydrological and oxythermal responses of neighbouring salmonid streams, with distinctive geologies, soil‐types, and localised riparian shading, to periods of anomalously warm conditions. During heatwaves, low flows, warm‐water temperatures, and diel oxygen variability, associated with biogenic production and respiration, predominated. In a low‐shade stream lacking significant catchment water storage, high daytime (>22°C) and night‐time (>19°C) water temperatures and low early morning O2 concentrations (<5 mg L−1) accumulated oxythermal stress for salmonids throughout summer. A stream with localised shading and a higher proportion of underlying aquifers and permeable soils throughout its watershed experienced considerably less cumulative oxythermal stress (O2 > 6 mg L−1; temperatures <19°C), whilst slower release of subsurface water bolstered base flows during dry spells. Our findings support conservation of shaded streams with permeable watersheds characterised by higher soil infiltration rates and aquifer storage capacity as salmonid sanctuaries under a warmer, drier summer climate. Preventing water quality and hydromorphological deterioration are paramount for safeguarding their role as climate refugia.

Magnetospheric‐Ionospheric‐Atmospheric Implications From the Juno Flyby of Ganymede

AbstractJuno flew over the northern mid‐latitudes of Ganymede during orbit 34 of the Juno mission, reaching an altitude of 1,053 km (16:56:07.972 UTC) at a sub spacecraft latitude/longitude of 33.66N, 57.5W degrees on 7 June 2021. Between 16:43 and 17:02 UT, Juno pierced Ganymede's magnetosphere at a velocity relative to Ganymede of 18.57 km s−1. Juno's instrumentation provided a unique opportunity to sample the local environment of Ganymede and its magnetosphere. We present measurements of the composition of the polar ionospheric outflow and the energetic electrons that penetrate Ganymede's atmosphere and produce its aurora. When these new observations are combined with modeling, conclusions can be drawn that affect our understanding of the atmosphere of Ganymede. The measured JADE precipitating plasma electrons provide an energy flux beyond that needed to create the observed oxygen emissions measured by UVS, but the electron energy spectrum is optically thin to the sparse atmosphere and does not provide the observed oxygen ultraviolet emission unless the O2 column density is increased by over an order of magnitude compared to previous atmospheric models. More than 99% of the electron energy flux passes through the atmosphere into the ice, thereby increasing the H2 and O2 content of the atmosphere. The increased H2 and O2 production is largely responsible for increasing the oxygen column density to a level that produces within known uncertainties the OI135.6 and OI130.4 nm emissions when bombarded by the electron energy flux observed by JADE. This suggests that past modeling efforts have underestimated the density of the atmosphere by over an order of magnitude.

Towards a sustainable energy future: Evaluating Arundo donax L. in continuous anaerobic digestion for biogas production

AbstractIn response to the EU's REPowerEU initiative (COM (2022) 108) which encourages an increase in biogas production by 20% in member states by 2030 to boost energy independence, it has become essential to identify sustainable alternatives to traditional feedstocks for biogas production, especially in the EU Member states where there is still high dependence on corn silage as the main raw material in biogas plants. While corn silage, predominantly used in the European biogas plants today, serves primarily for the livestock sector, alternative sources need to be explored. Therefore, this study aimed to evaluate the potential of Arundo donax, a perennial energy crop, as an alternative feedstock in a continuous anaerobic process. The biogas yield and its quality, characterized by CH4, CO2, H2S and O2 content, were determined during a continuous process with A. donax, compared with two mixed feedstocks of A. donax and corn silage over a 5‐month period in a continuous anaerobic digestion process. The results revealed that A. donax exhibits a biogas yield and methane content comparable to corn silage, indicating its potential as a viable and sustainable alternative feedstock for biogas production.

Experimental study and equilibrium analysis on thermal reduction of CO2 by CFB gasification

CO2 can be involved in the CFB gasification process as one of the gasifying agents and be reduced to CO. In this paper, the feasibility of using CFB gasification process to reduce CO2 was investigated by using a bench-scale CFB gasifier. The effect of gasifying agent parameters including the CO2 substitution for N2, the O2 concentration and O2/C were studied. The result of experiments was compared with the chemical equilibrium calculations. The experimental result shows that the reduction of CO2 can be realized in CFB gasification, and the yield of CO in O2/CO2 atmosphere is higher than that in air atmosphere. When the O2 concentration is 30%, the CO2 conversion reached the maximum of 0.017 Nm3(CO2)/kg (coal). However, the conversion of CO2 is limited by temperature and char reactivity at higher CO2 concentration. The gradual increase in CO2 yield with increasing O2/C suggests that at approximate temperature, the increase in O2/C enhances the oxidation of C and CO. When O2/C is greater than 0.45, the gasification results reach equilibrium. Under other conditions, the gasification results differ from the chemical equilibrium significantly. This is due to the change in the dominant reaction of the gasification process from the combustion reactions to the Boudouard reaction.

Numerical Analysis of the Coal Mixture Composition Effects on Combustion and Gas Emissions in CFB Boiler

The combustion system in the CFB boiler had a high complexity, in order to identify and understand the combustion process that occurs in the CFB boiler, CFD analysis was applied. This study was conducted to analyze the combustion and gas emissions produced in a CFB boiler with several variations of coal mixture. Coal particles injected into the furnace were modeled with DPM, specifically the Euler-Lagrange approach. The coal used came from two coal mining industries and mixed with the percentages of 20% : 80%, 30% : 70% and 40% : 60%. The amounts and conditions of combustion air and coal had been determined. The simulation process in the CFB boiler was carried out at a maximum load (110 MWe) without involving bed material. The results showed that the energy and combustion temperature produced in the mixture of 20% : 80% reached the highest value, the mixture of 40% : 60% produced the highest concentration of H2O and produced the lowest concentrations of CO2, O2, NO and SO2. On the other hand, the distribution of pressure and gas velocity had relatively the same value in each mixture. This could be caused by the characteristics of coal mixture, the amount of air and coal injected, and the absence of bed material.

Understanding of MILD Combustion Characteristics of NH3 Air Flames in N2 And H2O Steam Diluted Environment at Atmospheric Pressure

Ammonia is becoming increasingly popular as a carbon-neutral fuel with zero carbon dioxide emissions. However, a significant hurdle lies in its combustion, which leads to substantial emissions of NOx. The current research involves conducting a chemical kinetic investigation to examine the characteristics of Intense Low oxygen Dilution (MILD) or Moderate combustion in ammonia (NH3)/air flames. This study is carried out under specific conditions, such as oxygen concentrations ranging from 11to 23%, premixed reactant temperatures between 1300 and 1700 K, and a pressure of one atmosphere. The study focuses on investigating the combustion characteristics of MILD using dilution with H2O and N2.With the rise in the inlet temperature of the premixed reactant, the peak temperature of the flame also rises. Moreover, flames diluted with H2O exhibit lower peak temperatures compared to flames diluted with N2.Flames diluted with H2O result in lower NOx emissions compared to flames diluted with N2. Additionally, for N2diluted flames, the exit NOx emissions rise as the oxygen concentration increases.Despite this, NOx emissions from H2Odiluted flames demonstrate non-monotonic behaviour.This means that the exit NOx increases initially as the oxygen concentration reaches 21%, but then begins to decrease. In contrast to N2and H2Odiluted flames exhibits a wider regime of no-ignition.Moreover, the rise in peak temperature in H2Odiluted flames is less apparent than in N2diluted flames, corresponding to broader ranges MILD combustion ranges.Furthermore, to attain MILD combustion in H2O diluted flames at a specific O2 concentration, the temperature of reactant needs to be higher than that required for N2diluted flames.

Oxygen levels affect oviduct epithelium functions in air–liquid interface culture

Key reproductive events such as fertilization and early embryonic development occur in the lumen of the oviduct. Since investigating these processes in vivo is both technically challenging and ethically sensitive, cell culture models have been established to reproduce the oviductal microenvironment. Compartmentalized culture systems, particularly air–liquid interface cultures (ALI; cells access the culture medium only from the basolateral cell side), result in highly differentiated oviduct epithelial cell cultures. The oxygen (O2) tension within the oviduct is 4–10% across species, and its reduced O2 content is presumed to be important for early reproductive processes. However, cell culture models of the oviduct are typically cultivated without O2 regulation and therefore at about 18% O2. To investigate the impact of O2 levels on oviduct epithelium functions in vitro, we cultured porcine oviduct epithelial cells (POEC) at the ALI using both physiological (5%) and supraphysiological (18%) O2 levels and two different media regimes. Epithelium architecture, barrier function, secretion of oviduct fluid surrogate (OFS), and marker gene expression were comparatively assessed. Under all culture conditions, ALI-POEC formed polarized, ciliated monolayers with appropriate barrier function. Exposure to 18% O2 accelerated epithelial differentiation and significantly increased the apical OFS volume and total protein content. Expression of oviduct genes and the abundance of OVGP1 (oviduct-specific glycoprotein 1) in the OFS were influenced by both O2 tension and medium choice. In conclusion, oviduct epithelial cells can adapt to a supraphysiological O2 environment. This adaptation, however, may alter their capability to replicate in vivo tissue characteristics.

Numerical Analysis of Thermal Flow Dynamics of Arc Plasma and Molten Pool in Hollow Cathode Arc Welding with Oxygen Content

The mechanism of the pulsed hollow cathode arc welding (HCAW) process was revealed using a fully coupled model with a hollow cathode. We solved the governing equations with the Marangoni effect to study the dynamic behaviors of a molten pool with a square pulsing current (200~400 A, 900 Hz) and varying O2 content; the dynamics of the arc plasma and the weld pool in the HCAW process were investigated quantitatively. The results show that the intensity of the arc plasma was more significantly weakened by the design of the hollow cathode in HCAW than that in GTAW with a solid hollow cathode. We could obtain a stable molten pool even with a large pulsing current section (200 A–400 A) at higher frequencies. The flow dynamics of the molten pool were mainly dominated by the Marangoni effect with varying oxygen content, and we could promote penetration by increasing O2 content in HCAW.

Zone-specific longshore sampling as a strategy to reduce uncertainties of SGD-driven solute fluxes from high-energy beaches

Submarine groundwater discharge (SGD) from intertidal beach systems forms a source of fresh and saline, often nutrient-enriched water to the near-shore across the world. The chemical composition of solute flux via SGD depends on several factors, including solid phase composition, organic matter supply, hydraulic gradients, as well as pore water residence time and origin, which are partly related to the beach topography. High-energy sandy beaches are especially prone to frequent sediment relocation and a variable topography, often characterized by a ridge and runnel structure. Topography may not only change on a temporal scale, but also in the longshore direction, which may alter SGD-driven solute fluxes. However, sampling high-energy beach sites is challenging and often does not allow for high resolution cross- and longshore sampling. We tested the approach of zone-specific pore water sampling, whereby samples were taken at the high water line, in the runnel, on top of the ridge, and close to the low water line of eight cross-shore transects. This was done in order to assess the longshore variability of pore water composition and flux over a 2.5 km wide beach section. In this study we relied on relatively few data points per transect and still found a characteristic cross-shore distribution of pore water parameters, related to redox conditions of each zone. Recharge zones (high water line and ridge) exhibited higher O2 and NOx concentrations and discharge zones (runnel and low water line) exhibited higher nutrient, DOC, Mn, and Fe concentrations. Furthermore, DOC concentrations in pore waters were lower than in coastal seawater, supporting previous assumptions of rapid organic matter turnover. Nevertheless, we observed large concentration ranges among samples assigned to the same zone, which could partly be related to longshore topography differences. The measured pore water concentrations and calculated SGD-driven solute fluxes indicated that sampling of single cross-shore transects may be representative for a beach section when assessing a redox-independent parameter like Si, while it is less representative for parameters affected by more complex biogeochemical processes like P, NH4, Mn, and Fe. For these, we suggest that longshore distributed data coverage combined with higher resolution sampling in discharge zones is a good strategy to reduce the uncertainty associated with estimating SGD-driven solute fluxes in a practicable way.

Role of the molecular structure of humified organic matter in rice plant response to environmental lead pollution.

Humified organic matter has been shown to decrease Pb toxicity in plants. However, there are still gaps in our understanding of the mechanism by which this phenomenon occurs. In this study, we aimed to assess the ability of humic substances (HSs), humic acids (HAs), and fulvic acids (FAs) to enhance defense mechanisms in rice plants under lead (Pb)-stressed conditions. HS fractions were isolated from vermicompost using the chemical fractionation methodology established by the International Humic Substances Society. These fractions were characterized by solid-state NMR and FTIR. Chemometric analysis was used to compare humic structures and correlate them with bioactivity. Three treatments were tested to evaluate the protective effect of humic fractions on rice plants. The first experiment involved the application of humic fractions along with Pb. The second comprised pretreatment with humic fractions followed by subsequent exposure to Pb stress. The third experiment involved Pb stress and subsequent treatment with humic fractions. The root morphology and components of the antioxidative defense system were evaluated and quantified. The results showed that HS + Pb, HA + Pb, and FA + Pb treatment preserved root growth and reduced the levels of O2- and malondialdehyde (MDA) in the roots by up to 5% and 2%, respectively. Pretreatment of the plants with humic fractions promoted the maintenance of root growth and reduced the contents of O2-, H2O2, and MDA by up to 48%, 22%, and 20%, respectively. Combined application of humic fractions and Pb reduced the Pb content in plant tissues by up to 60%, while pretreatment reduced it by up to 80%. The protective capacity of humic fractions is related to the presence of peptides, lignin, and carbohydrate fragments in their molecular structures. These results suggest that products could be developed that can mitigate the adverse effects of heavy metals on agricultural crops.

Reaction mechanism and light gas conversion in pyrolysis and oxidation of dimethyl ether (DME): A ReaxFF molecular dynamics study

To uncover the microscopic reaction mechanisms of dimethyl ether (DME) pyrolysis and oxidation, reactive molecular dynamics simulations were employed to investigate the reaction processes under various O2/DME ratios and impurity environments at 2200 K–3200 K. The results show that DME pyrolysis begins with a decomposition reaction of CH3OCH3 → CH3O + CH3, ultimately leading to the formation of CO, H2 and PAHs. The reaction pathways of DME oxidation contain light gas conversion and combustion. In fuel rich conditions, the oxidation produces mainly H2 and CO, while in fuel lean conditions, the oxidation products tend to be H2O and CO2. The carbon components of DME are completely converted into CO2 and CO regardless of O2 content. In the presence of impurities H2O or CO2, the oxidation reaction pathway is altered, causing consumption and transformation of these impurities into active radicals such as OH, further promoting the progress of the reaction. The top three light gases produced are hydrogen, methanol and methane, and increasing H2 production in the DME oxidation process can be achieved through both oxygen subtraction and water addition. The rate of formaldehyde generation during pyrolysis is higher than that during oxidation. However, a higher oxygen content leads to increased formaldehyde production.

Quantitative measurement of sodium emissions during oxy-fuel combustion of a beech wood biomass particle using laser-induced breakdown spectroscopy

Oxy-fuel biomass combustion in a circulating fluidized bed is a clean and sustainable biomass utilization technology. Woody forest biomass is considered a promising source of renewable energy because of its widespread availability across the globe. However, effective biomass utilization in thermal power plants is largely limited by severe ash deposition and corrosion of heat transfer surfaces due to alkali metal and chlorine emissions during biomass combustion. In this study, laser-induced breakdown spectroscopy (LIBS) was applied to detect in-situ gas phase sodium (Na) emission during single particle combustion of widely available forest biomass, namely, beech wood. The operating conditions simulate the thermo-chemical conditions relevant to a fluidized bed combustor system, where the operating temperature varies between 1073K–1273K. This work aims to investigate the effect of O2 concentration, CO2 (oxyfuel environment), and particle size on the emission of sodium during the combustion of a single beech wood particle. The unresolved sodium doublet was used as the LIBS signal to quantify sodium emission concentration.Oxygen concentration is the most critical parameter affecting Na emissions, and an increase in O2 concentration led to higher Na emissions. It is observed that there is a significant reduction in the emission of Na in an O2/CO2 environment as compared to an O2/N2 environment. It is hypothesized that this drop in Na emissions in O2/CO2 environment could be due to lower particle temperatures caused by the lower diffusivity of O2 in CO2 as well as the endothermic gasification reaction in high CO2 environments. In addition, it is reported that the dissociation of sodium carboxylates and carbonates in the biomass matrix to release gaseous Na due to thermal decomposition is retarded at higher CO2 concentrations which could explain the drop in Na emissions. The effect of biomass particle size is pronounced mainly at lower concentration of O2 where, larger particles keep Na trapped in its matrix, however, at higher O2 concentrations (30%), the effect of particle size on Na emission is negligible.

Modelling and Design of a Novel Integrated Heat Exchange Reactor for Oxy-Fuel Combustion Flue Gas Deoxygenation

The concentration of residual O2 in oxy-fuel combustion flue gas needs to be reduced before CO2 transportation, utilization, or storage. An original application of the printed circuit heat exchanger (PCHE) for catalytic combustion with natural gas (catalytic deoxygenation) is described for reducing the residual O2 concentration. The PCHE design features multiple adiabatic packed beds with interstage cooling and fuel injection, allowing precise control over the reaction extent and temperature within each reaction stage through the manipulation of fuel and utility flow rates. This work describes the design of a PCHE for methane–oxygen catalytic combustion where the catalyst loading is minimized while reducing the O2 concentration from 3 vol% to 100 ppmv, considering a maximum adiabatic temperature rise of 50 °C per stage. Each PCHE design differs by the number of reaction stages and its individual bed lengths. As part of the design process, a one-dimensional transient reduced-order reactor model (1D ROM) was developed and compared to temperature and species concentration axial profiles from 3D CFD simulations. The final design consists of five reaction stages and four heat exchanger sections, providing a PCHE length of 1.09 m at a processing rate of 12.3 kg/s flue gas per m3 PCHE.