Concentrations Of Polycyclic Aromatic Compounds Research Articles

Determination of polycyclic aromatic hydrocarbons, dibenzothiophene, and alkylated homologs in the lichen Hypogymnia physodes by gas chromatography using single quadrupole mass spectrometry and time-of-flight mass spectrometry

Development of the Athabasca Oil Sands Region in northeastern Alberta, Canada has contributed polycyclic aromatic hydrocarbons (PAHs) and polycyclic aromatic compounds (PACs), which include alkyl PAHs and dibenzothiophenes, to the regional environment. A new analytical method was developed for quantification of PAHs and PACs in the epiphytic lichen bioindicator species Hypogymnia physodes for use in the development of receptor models for attribution of PAH and PAC concentrations to anthropogenic and natural emission sources. Milled lichens were extracted with cyclohexane, and extracts were cleaned on silica gel using automated solid phase extraction techniques. Quantitative analysis was performed by gas chromatography with selected ion monitoring (GC-SIM-MS) for PAHs, and by GC with time-of-flight mass spectrometry (GC-TOF-MS) for PACs. PACs were quantitated in groups using representative reference compounds as calibration standards. Analytical detection limits were ≤2.5ngg−1 for all individual compounds. Precision as measured by laboratory duplicates was variable; for individual analytes above 5ngg−1 the mean absolute difference between duplicates was typically <20%. Selection of single-analyte markers for source attribution should include consideration of data quality indicators. Use of TOF-MS to spectrally characterize PAC group constituents identified significant challenges for the accurate quantitation of PACs with more than two carbons in their side chain(s). Total PAH concentrations in lichen samples ranged from 12 to 482ngg−1. Total PACs in each sample varied from a fraction of total PAHs to more than four times total PAHs. Results of our analyses of H. physodes are compared with other studies using other species of lichens as PAH receptors and with passive monitoring data using polyurethane foam (PUF) samplers in the Athabasca Oil Sands Region (AOSR). This study presents the first analytical methodology developed for the determination of PACs in an epiphytic lichen bioindicator species.

Temporal variation in the deposition of polycyclic aromatic compounds in snow in the Athabasca Oil Sands area of Alberta.

Atmospheric deposition of polycyclic aromatic compounds (PACs) via and onto snow, and their releasing during spring snowmelt has been a concern in the Athabasca Oil Sands Region of Alberta. This study was designed to evaluate the concentrations, loadings, and distribution of PACs in springtime snowpack and how they have changed since the first study in 2008. Snowpack samples were collected in late winters 2011-2014 at varying distances from the main developments. PAC concentration and deposition declined exponentially with distance, with pyrenes, chrysenes, and dibenzothiophenes dominating the distribution within the first 50km. The distribution of PACs was different between sites located close to upgraders and others located close to mining facilities. Overall, PAC loadings were correlated with priority pollutant elements and water chemistry parameters, while wind direction and speed were not strong contributors to the variability observed. Total PAC mass deposition during winter months and within the first 50km was initially estimated by integrating the exponential decay function fitted through the data using a limited number of sites from 2011 to 2014: 1236kg (2011), 1800kg (2012), 814kg (2013), and 1367 (2014). Total loadings were estimated to have a twofold increase between 2008 and 2014, although the increase observed was not constant. Finally, kriging interpolation is presented as an alternative and more robust approach to estimate PAC mass deposition in the area. After a more intensive sampling campaign in 2014, the PAC mass deposition was estimated to be 1968kg.

Probing the Adsorption of Polycyclic Aromatic Compounds onto Water Droplets Using Molecular Dynamics Simulations

A series of molecular dynamics (MD) simulations were performed to probe the adsorption behaviors of polycyclic aromatic compounds (PACs) from n-heptane and toluene onto water droplets. In n-heptane, the simulations revealed distinct adsorbed structures of PAC molecules on the water droplets with different sizes. In the system with a small water droplet (radius 1.86 nm), the adsorbed PAC aggregate renders a straight one-dimensional (1D) structure; contrarily, in the presence of a large water droplet (radius 3.10 nm), a bent 1D structure of nonzero curvature is formed. Such size effect is a result from the delicate balance between the deformation energy required for adsorption and the available attractions between the PAC and water molecules. While the adsorbed structures are sensitive to the size of the water droplet at relatively low PAC concentration in n-heptane, the size effect in toluene is only prominent when the concentration of PAC molecules is sufficiently high.

Target Analysis of Polycyclic Aromatic Hydrocarbons (PAHs) in Consumer Products and Total Content of Polycyclic Aromatic Compounds (PACs)

ABSTRACTThe fabrication of consumer products is tightly linked to the usage of polymeric materials. The application of mineral oil products as plasticizers or lubricants in this manufacture is very common and so is the addition of carbon black for coloring and abrasion resistance purposes. Whereas mineral oils often contain highly alkylated aromatic species, alkylation of polycyclic aromatic compounds (PACs) is rather low or even absent in the case of carbon black. Since they are broadly applied in various products, consumers might get exposed to PACs, for instance, via dermal contacts. Here, we characterized several commodities not only via the common way of targeted analysis for their contents on PAHs, but also with regard to its total amounts of unsubstituted and substituted aromatic hydrocarbons. The methods applied to analyze consumer products were as follows: (i) online coupling of liquid chromatography to gas chromatography with flame ionization detection (LC-GC-FID) for quantification of total PAH and mineral oil saturated hydrocarbon (MOSH) contents; (ii) coupling of tandem mass spectrometry to gas chromatography (GC-MS/MS) to quantify occasionally occurring PAHs with high specificity; and (iii) 2D gas chromatography coupled to time-of-flight mass spectrometry (GCxGC-MS) to characterize the complex mixtures concerning analytes’ ring systems and degrees of alkylation. We found PAH contents in the range of parts per million (ppm) in consumer products, while overall amounts of aromatics were in the percent range.

One-year study of polycyclic aromatic compounds at an urban site in Grenoble (France): Seasonal variations, gas/particle partitioning and cancer risk estimation

21 PAHs, 27 oxy-PAHs and 32 nitro-PAHs were measured every third day over a year in both gaseous (G) and particulate PM10 (P) phases in ambient air of Grenoble (France). Mean total concentrations (G+P) of PAHs and oxy-PAHs were in the same range and about 10ngm−3. Nitro-PAHs were 50 to 100 times less concentrated averaging 100pgm−3. Polycyclic aromatic compound (PAC) concentrations were 5 to 7 times higher in “cold” period (October to March) than in “warm” period (April to September). Seasonal variations may be explained by higher primary emissions from residential heating, especially biomass burning in “cold” season. Meteorological conditions and influence of the geomorphology around Grenoble, with the formation of thermal inversion layers leading to the stagnation of pollutants, were additional key parameters. Maximum individual PAC concentrations were observed during two PM10 pollution events in December and February–March. Chemical processes and secondary formation of oxy- and nitro-PAH were probably enhanced by the accumulation of the pollutants during these events. PAC gas/particle partitioning depended on compound molecular weight and vapour pressure. Gas/particle partitioning of oxy- and nitro-PAHs were evaluated using a multi-phase poly-parameter linear free energy relationship model. The PAC cancer risk was assessed using toxic equivalency factors available in the literature (19 PAHs, 10 nitro-PAHs and 1 oxy-PAH). Overall, particle-bound PACs contributed about 76% of the cancer risk. While PAHs accounted for most of the total PAC cancer risk, oxy- and nitro-PAHs could account for up to 24%. The risk quantification across substance classes is limited by toxicological data availability.

Assessing the contribution of combustion-derived contaminants to a remote subarctic environment from traffic on the Tibbitt to Contwoyto winter road (Northwest Territories, Canada)

Remote mining operations in Canada's Northwest Territories and Nunavut are supported by a 600km winter road, which spans the transition from subarctic boreal forest in Yellowknife to low Arctic tundra. Each year, thousands of truckloads of fuel, large equipment, and other heavy loads are hauled up the winter road. We investigated whether diesel emissions from commercial truck traffic is a major source of metals and polycyclic aromatic compounds (PACs) to aquatic ecosystems along the winter road. In March 2014, at the end of the hauling season, we collected integrated snow samples, water, and sediment from nine lakes located along the winter road, as well as from six lakes located within the city of Yellowknife. Examination of PAC composition and diagnostic ratios in snow samples showed that wildfires are an important source of PACs to lakes along the winter road, while anthropogenic sources are more prevalent in snow from Yellowknife lakes. Concentrations of PACs, including those associated with diesel emissions, were variable in snow, water, and sediment across all sites. The highest concentrations of PACs in snow were reported in winter road lakes located in the subarctic boreal forest, where forest fires are common. No compositional differences were observed for PACs in sediment and water samples between Yellowknife and winter road lakes. We did not observe any evidence of metal contamination in snow collected along the winter road, and metal concentrations in snow from winter road sites were consistently lower than Yellowknife sites. Our results show that a high contribution of PACs from natural sources can obscure potential contributions from diesel traffic emissions along the winter road.

Stability of polycyclic aromatic compounds in polyurethane foam-type passive air samplers upon O3 exposure

Stability of polycyclic aromatic compounds (PACs) in polyurethane foam (PUF) disks upon O3 exposure was studied in a flow tube. A wide range of PACs was evaluated by spiking PUF disks with PACs and exposing to O3 at concentrations that were equivalent to two months exposure, a typical deployment period for these passive air samplers. Ambient concentrations of O3 (∼50 ppb) at 0% and 50% relative humidity (RH) were applied. At 0% RH, 23 of 68 PACs yielded more than 50% loss after exposure. The mean percent loss was 30% with perylene and 9,10-dimethylanthracene the most reactive polycyclic aromatic hydrocarbons (PAHs) and alkylated PAHs, respectively. At 50% RH, 77% of the studied PACs was stable upon O3 exposure (PACexposed/PACunexposed > 0.7). The mean percent loss was 17% and only 7 of 68 PACs yielded greater than 50% loss. In general, the reactivity of most of the PACs decreased at higher RH, except for the reactive PAHs (acenaphthylene, 2,3-dimethylanthracene, 9,10-dimethylanthracene, dibenzothiophene, and 2-methyldibenzothiophene) which demonstrated lower RH dependence. The experimental conditions in this study represent a worst case scenario for the stability of PACs sorbed to PUF. In reality, the sampling of PACs in ambient air represents an ‘aged’ component of PACs where the most reactive species have already partially been removed. Also, PACs in ambient air will be associated with the particle phase to varying extents that will help to enhance their stability. Therefore, under regular operating conditions, over a 2-month exposure, we expect a minimal error in the measurement of total concentration of PACs in air using the PUF disk passive sampler.

Analysis of vacuum tower asphalt extender and effect on bitumen and asphalt properties

Interest has increased related to the impact on asphalt performance of bitumen containing vacuum tower asphalt extender (VTAE), the non-distillable fraction from re-refining used engine oil. This laboratory study provides information on bitumen and asphalt characteristics with and without VTAE. VTAE was blended with PG 64-22 to achieve bitumen grade of PG 58-28. To serve as control a second PG 58-28 was formulated using PG 52-28 with the same PG 64-22. The bitumens were analysed for Superpave PG grade, X-ray fluorescence and polycyclic aromatic compound content, and also using gel permeation chromatography and thermogravimetric analysis. Grade results showed no appreciable difference in ageing between the two PG 58-28 bitumens after Rolling Thin-Film Oven and Pressure Ageing Vessel ageing. The second portion of the study compares asphalt prepared with the two PG 58-28 bitumens including volumetric properties, resistance to moisture damage and rutting, stiffness and fatigue resistance. Fatigue specimens were subjected to short-term and long-term ageing. Asphalt with the VTAE bitumen had equal or increased fatigue resistance in both the short-term and long-term aged conditions. Bitumen was recovered from each ageing condition and tested for binder grade. Comparing the two PG 58-28 bitumens showed no significant difference in stiffness or low temperature properties.

Elemental carbon and polycyclic aromatic compounds in a 150-year sediment core from Lake Qinghai, Tibetan Plateau, China: influence of regional and local sources and transport pathways.

Elemental carbon (EC) and polycyclic aromatic compounds (PACs) are potential proxies for the reconstruction of change in human activities and the origin of air masses in historic times. In this study, the historic deposition of char and soot (the two subtypes of EC) and PACs in a 150-year sediment core from different topographic subbasins of Lake Qinghai on the Qinghai Tibetan Plateau (QTP) were reconstructed. The objective was to explore how the variations in the concentrations of EC and PACs, in the ratios of char to soot and of oxygenated polycyclic aromatic hydrocarbons (OPAHs) to parent PAHs, and in the composition of the PAC mixtures reflect historical changes in climate and human activity and the origin of air masses arriving at the QTP. The deposition fluxes of soot in the different subbasins were similar, averaging 0.18 (range of 0.15-0.25) and 0.16 (0.13-0.23) g m(-2) year(-1), respectively, but they varied for char (averaging 0.11 and 0.22 g m(-2) year(-1), respectively), suggesting ubiquitous atmospheric deposition of soot and local river inputs of char. The different vertical distributions of the char/soot ratios in the different subbasins can be interpreted in terms of the different transport mechanisms of char and soot. An abrupt increase in soot concentrations since 1980 coincides with results from the QTP ice cores that were interpreted to be indicative of soot transport from South Asia. Similar concentration patterns of PAHs with soot and 9,10-anthraquinone/anthracene (9,10-AQ/ANT) ratios all >2.0 suggest regional PAC sources. Increasing PAH/soot ratios and decreasing 9,10-AQ/ANT ratios since the beginning of the 1970s indicate increasing local emissions. The historical trends of these diagnostic ratios indicate an increase in the fossil-fuel contribution since the beginning of the 1970s. The increase of perylene concentrations with increasing core depth and the ratio of perylene to its penta-aromatic isomers indicate that perylene originates mainly from in situ biogenic diagenesis. We demonstrate that the concentrations of EC, char, soot, and PACs in sediments can be used to reconstruct local, regional, and remote sources and transport pathways of pollutants to the QTP.

First results from the oil sands passive air monitoring network for polycyclic aromatic compounds.

Results are reported from an ongoing passive air monitoring study for polycyclic aromatic compounds (PACs) in the Athabasca oil sands region in Alberta, Canada. Polyurethane foam (PUF) disk passive air samplers were deployed for consecutive 2-month periods from November 2010 to June 2012 at 17 sites. Samples were analyzed for polycyclic aromatic hydrocarbons (PAHs), alkylated PAHs, dibenzothiophene and its alkylated derivatives (DBTs). Relative to parent PAHs, alkylated PAHs and DBTs are enriched in bitumen and therefore considered to be petrogenic markers. Concentrations in air were in the range 0.03-210 ng/m(3), 0.15-230 ng/m(3) and 0.01-61 ng/m(3) for ∑PAHs, ∑alkylated PAHs and ΣDBTs, respectively. An exponential decline of the PAC concentrations in air with distance from mining areas and related petrogenic sources was observed. The most significant exponential declines were for the alkylated PAHs and DBTs and attributed to their association with mining-related emissions and near-source deposition, due to their lower volatility and greater association with depositing particles. Seasonal trends in concentrations in air for PACs were not observed for any of the compound classes. However, a forest fire episode during April to July 2011 resulted in greatly elevated PAH levels at all passive sampling locations. Alkylated PAHs and DBTs were not elevated during the forest fire period, supporting their association with petrogenic sources. Based on the results of this study, an "Athabasca PAC profile" is proposed as a potential source marker for the oil sands region. The profile is characterized by ∑PAHs/∑Alkylated PAHs = ∼0.2 and ∑PAHs/∑DBTs = ∼5.

Chemical fingerprinting of hydrocarbon-contamination in soil.

Chemical fingerprinting analyses of 29 hydrocarbon-contaminated soils were performed to assess the soil quality and determine the main contaminant sources. The results were compared to an assessment based on concentrations of the 16 priority polycyclic aromatic hydrocarbons pointed out by the U.S. Environmental Protection Agency (EPAPAH16) and total petroleum hydrocarbon (TPH). The chemical fingerprinting strategy proposed in this study included four tiers: (i) qualitative analysis of GC-FID chromatograms, (ii) comparison of the chemical composition of both un-substituted and alkyl-substituted polycyclic aromatic compounds (PACs), (iii) diagnostic ratios of selected PACs, and (iv) multivariate data analysis of sum-normalized PAC concentrations. The assessment criteria included quantitative analysis of 19 PACs and C1-C4 alkyl-substituted homologues of naphthalene, fluorene, dibenzothiophene, phenanthrene, pyrene, and chrysene; and 13 oxygenated polycyclic aromatic compounds (O-PACs). The chemical composition of un-substituted and alkyl-substituted PACs and visual interpretation of GC-FID chromatograms were in combination successful in differentiating pyrogenic and petrogenic hydrocarbon sources and in assessing weathering trends of hydrocarbon contamination in the soils. Multivariate data analysis of sum-normalized concentrations could as a stand-alone tool distinguish between hydrocarbon sources of petrogenic and pyrogenic origin, differentiate within petrogenic sources, and detect weathering trends. Diagnostic ratios of PACs were not successful for source identification of the heavily weathered hydrocarbon sources in the soils. The fingerprinting of contaminated soils revealed an underestimation of PACs in petrogenic contaminated soils when the assessment was based solely on EPAPAH16. As alkyl-substituted PACs are dominant in petrogenic sources, the evaluation of the total load of PACs based on EPAPAH16 was not representative. Likewise, the O-PACs are not represented in soil quality assessments based on EPAPAH16 and TPH. The ∑O-PACs ranged between <limit of detection (LOD) (0.03 mg kg(-1) (dw)) and 150.61 mg kg(-1) (dw). The pyrogenic contaminated soils contained considerable amount of O-PACs corresponding to between 6 and 18% of the ∑EPAPAH16.

Polycyclic aromatic hydrocarbons (PAHs) and their derivatives (alkyl-PAHs, oxygenated-PAHs, nitrated-PAHs and azaarenes) in urban road dusts from Xi’an, Central China

Urban road dusts are carriers of polycyclic aromatic compounds (PACs) and are therefore considered to be a major source of contamination of other environmental compartments and a source of exposure to PACs for urban populations. We determined the occurrence, composition pattern and sources of several PACs (29 alkyl- and parent-PAHs, 15 oxygenated-PAHs (OPAHs), 4 azaarenes (AZAs), and 11 nitrated-PAHs (NPAHs)) in twenty urban road dusts and six suburban surface soils (0–5cm) from Xi’an, central China. The average concentrations of ∑29PAHs, ∑4AZAs, ∑15OPAHs, and ∑11NPAHs were 15767, 673, 4754, and 885ngg−1 in road dusts and 2067, 784, 854, and 118ngg−1 in surface soils, respectively. The concentrations of most individual PACs were higher in street dusts than suburban soils, particularly for PACs with molecular weight>192gmol−1. The enrichment factors of individual PACs were significantly positively correlated with log KOA and log KOW, indicating an increasing deposition and co-sorption of the PACs in urban dusts with decreasing volatility and increasing hydrophobicity. Significant correlations between the concentrations of individual and sum of PACs, carbon fractions (soot and char), and source-characteristic PACs (combustion-derived PAHs and retene, etc.), indicated that PAHs, OPAHs and AZAs were mostly directly emitted from combustion activities and had similar post-emission fates, but NPAHs were possibly more intensely photolyzed after deposition as well as being emitted from vehicle exhaust sources. The incremental lifetime cancer risk (ILCR) resulting from exposure to urban dust bound-PACs was higher than 10−6, indicating a non-negligible cancer risk to residents of Xi’an.

Measurements of abatement of particles and exhaust gases in a marine gas scrubber

Measurements of exhaust gases from a marine engine equipped with an open-loop wet scrubber using seawater for sulphur dioxide (SO2) abatement are reported. The scrubber reduces the SO2 emissions effectively to levels corresponding to &lt;0.1% S in the fuel (the level that applies to sulphur emission control areas from 2015). The scrubber also reduces the emissions of particulate matter by mass by 75%. The impact on the number of particles is studied for the total particle number and the solid fraction. The total number of particles is reduced by about 92% and the solid fraction by 48% in the scrubber indicating most effective abatement of volatile particles. Also, the content of polycyclic aromatic compounds in the exhaust is significantly reduced by the scrubber. The captured SO2 gives a low pH and high sulphate content in the scrubber water. The reduction in particulate matter is of the same order as what is obtained with a fuel switch from heavy fuel oil to marine gas oil.

Hydrogenation of aromatic hydrocarbons in the presence of dibenzothiophene over platinum-palladium catalysts based on Al-SBA-15 aluminosilicates

The hydrogenation of a 2-methylnaphthalene solution in n-heptane in the presence of dibenzothiophene (400 ppm in terms of sulfur) over Pt-Pd catalysts containing Al-SBA-15 mesoporous aluminosilicates has been studied. Supports for the catalysts contained 35 wt % Al-SBA-15 and 65 wt % γ-Al2O3. The Pt and Pd contents of the catalysts was 0.25 and 1.0 wt %, respectively. Experiments with the model feedstock were conducted in an autoclave at 240–260°C, an initial hydrogen pressure of 30 atm, and a substrate/metal weight ratio of 30. It has been found that a catalyst based on Al-SBA-15 with Si/Al = 5 exhibits the highest activity under poisoning with 400 ppm sulfur. Thus, the conversion of 2-methylnaphthalene at 260°C after 3 h was 85% with the selectivity for methyltetralins of 97%. The dearomatization of a hydrotreated diesel fraction with 45 ppm sulfur at 260°C at a pressure of 30 atm and a space velocity of 2.4 h−1 has made it possible to decrease the total aromatic content, in particular reduce the concentration of polycyclic aromatic compounds to a level of less than 1 wt %.

Acute, Subchronic, and Developmental Toxicological Properties of Lubricating Oil Base Stocks

Lubricating oil base stocks (LOBs) are substances used in the manufacture of finished lubricants and greases. They are produced from residue remaining after atmospheric distillation of crude oil that is subsequently fractionated by vacuum distillation and additional refining steps. Initial LOB streams that have been produced by vacuum distillation but not further refined may contain polycyclic aromatic compounds (PACs) and may present carcinogenic hazards. In modern refineries, LOBs are further refined by multistep processes including solvent extraction and/or hydrogen treatment to reduce the levels of PACs and other undesirable constituents. Thus, mildly (insufficiently) refined LOBs are potentially more hazardous than more severely (sufficiently) refined LOBs. This article discusses the evaluation of LOBs using statistical models based on content of PACs; these models indicate that insufficiently refined LOBs (potentially carcinogenic LOBs) can also produce systemic and developmental effects with repeated dermal exposure. Experimental data were also obtained in ten 13-week dermal studies in rats, eight 4-week dermal studies in rabbits, and seven dermal developmental toxicity studies with sufficiently refined LOBs (noncarcinogenic and commonly marketed) in which no observed adverse effect levels for systemic toxicity and developmental toxicity were 1000 to 2000 mg/kg/d with dermal exposures, typically the highest dose tested. Results in both oral and inhalation developmental toxicity studies were similar. This absence of toxicologically relevant findings was consistent with lower PAC content of sufficiently refined LOBs. Based on data on reproductive organs with repeated dosing and parameters in developmental toxicity studies, sufficiently refined LOBs are likely to have little, if any, effect on reproductive parameters.

Subchronic and Developmental Toxicity of Aromatic Extracts

Aromatic extracts (AEs; distillate AEs [DAEs] and residual AEs [RAEs]) are complex, highly viscous liquid petroleum streams with variable compositions derived by extraction of aromatic compounds from distillate and residual petroleum fractions from a vacuum distillation tower, respectively. The DAEs generally contain significant amounts of polycyclic aromatic compounds (PACs) and are carcinogenic. The RAEs typically contain lower concentrations of biologically active PACs. The PACs in refinery streams can cause effects in repeated-dose and developmental toxicity studies. In a 13-week dermal study, light paraffinic DAE had several dose-related effects involving multiple organs; no-observed-effect level was <5 mg/kg/d, with no overt toxicity. Predicted dose-responses at 10% (PDR10s), modeled doses causing a 10% effect on sensitive end points based on PAC content, ranged from 25 to 78 mg/kg/d for untested paraffinic DAEs. The no observed adverse effect level (NOAEL) for developmental toxicity for light paraffinic DAE was 5 mg/kg/d. Statistically significant developmental effects at higher doses were associated with maternal effects. The PDR10s for developmental toxicity of paraffinic DAEs ranged from 7 to >2000 mg/kg/d, reflecting differences due to variation in PACs. The NOAELs for RAEs were 500 mg/kg for 90-day studies and 2000 mg/kg for developmental toxicity. Reproductive toxicity is not considered to be a sensitive end point for AEs based on the toxicity tests with DAEs, RAEs, and other PAC-containing petroleum substances. In vivo micronucleus tests on heavy paraffinic DAE, RAEs, and a range of other petroleum substances have been negative. The exception to this general trend was a marginally positive response with light paraffinic DAE. Most DAEs are considered unlikely to produce chromosomal effects in vivo.

PM2.5-bound oxygenated PAHs, nitro-PAHs and parent-PAHs from the atmosphere of a Chinese megacity: Seasonal variation, sources and cancer risk assessment

Polycyclic aromatic compounds (PACs) in air particulate matter contribute considerably to the health risk of air pollution. The objectives of this study were to assess the occurrence and variation in concentrations and sources of PM2.5-bound PACs [Oxygenated PAHs (OPAHs), nitro-PAHs and parent-PAHs] sampled from the atmosphere of a typical Chinese megacity (Xi'an), to study the influence of meteorological conditions on PACs and to estimate the lifetime excess cancer risk to the residents of Xi'an (from inhalation of PM2.5-bound PACs). To achieve these objectives, we sampled 24-h PM2.5 aerosols (once in every 6days, from 5 July 2008 to 8 August 2009) from the atmosphere of Xi'an and measured the concentrations of PACs in them. The PM2.5-bound concentrations of Σcarbonyl-OPAHs, ∑hydroxyl+carboxyl-OPAHs, Σnitro-PAHs and Σalkyl+parent-PAHs ranged between 5–22, 0.2–13, 0.3–7, and 7–387ngm−3, respectively, being markedly higher than in most western cities. This represented a range of 0.01–0.4% and 0.002–0.06% of the mass of organic C in PM2.5 and the total mass of PM2.5, respectively. The sums of the concentrations of each compound group had winter-to-summer ratios ranging from 3 to 8 and most individual OPAHs and nitro-PAHs had higher concentrations in winter than in summer, suggesting a dominant influence of emissions from household heating and winter meteorological conditions. Ambient temperature, air pressure, and wind speed explained a large part of the temporal variation in PACs concentrations. The lifetime excess cancer risk from inhalation (attributable to selected PAHs and nitro-PAHs) was six fold higher in winter (averaging 1450 persons per million residents of Xi'an) than in summer. Our results call for the development of emission control measures.

Personal Breathing Zone Exposures among Hot-Mix Asphalt Paving Workers; Preliminary Analysis for Trends and Analysis of Work Practices That Resulted in the Highest Exposure Concentrations

An exposure assessment of hot-mix asphalt (HMA) paving workers was conducted to determine which of four exposure scenarios impacted worker exposure and dose. Goals of this report are to present the personal-breathing zone (PBZ) data, discuss the impact of substituting the releasing/cleaning agent, and discuss work practices that resulted in the highest exposure concentration for each analyte. One-hundred-seven PBZ samples were collected from HMA paving workers on days when diesel oil was used as a releasing/cleaning agent. An additional 36 PBZ samples were collected on days when B-100 (100% biodiesel, containing no petroleum-derived products) was used as a substitute releasing/cleaning agent. Twenty-four PBZ samples were collected from a reference group of concrete workers, who also worked in outdoor construction but had no exposure to asphalt emissions. Background and field blank samples were also collected daily. Total particulates and the benzene soluble fraction were determined gravimetrically. Total organic matter was determined using gas chromatography (GC) with flame ionization detection and provided qualitative information about other exposure sources contributing to worker exposure besides asphalt emissions. Thirty-three individual polycyclic aromatic compounds (PACs) were determined using GC with time-of-flight mass spectrometry; results were presented as either the concentration of an individual PAC or a summation of the individual PACs containing either 2- to 3-rings or 4- to 6-rings. Samples were also screened for PACs containing 4- to 6-rings using fluorescence spectroscopy. Arithmetic means, medians, and box plots of the PBZ data were used to evaluate trends in the data. Box plots illustrating the diesel oil results were more variable than the B-100. Also, the highest diesel oil results were much higher in concentration than the highest B-100 results. An analysis of the highest exposure results and field notes revealed a probable association between these exposures and the use of diesel oil, use of a diesel-powered screed, elevated HMA paving application temperatures, lubricating and working on broken-down equipment, and operation of a broom machine. [Supplementary materials are available for this article. Go to the publisher's online edition of Journal of Occupational and Environmental Hygiene for the following free supplemental resource: a file containing tables summarizing statistical data and individual analyte results.]

Limited Waterborne Acute Toxicity of Native Polycyclic Aromatic Compounds from Coals of Different Types Compared to Their Total Hazard Potential

Coals contain native polycyclic aromatic compounds (PACs), which include polycyclic aromatic hydrocarbons (PAHs), and heterocyclic aromatic compounds (NSO-PACs) in considerably varying amounts up to 2500 mg/kg. Whereas PAC bioavailability and toxicity from coals are generally considered to be low, few studies have considered potential variations arising from the composition of different coal types including native PAC content. In the present study, fine particles of different coal types exhibiting variable properties were systematically investigated regarding their PAC bioavailability. PAH content reached up to 79 mg/kg EPA-PAH and 865 mg/kg total PAH. Determination of the toxic potential of extracted PACs in bioassays showed inhibition of Caenorhabditis elegans reproduction (up to 94%) and increased mortality of Danio rerio embryos (up to 100%) after exposure to extracts from lignite, sub-bituminous, and bituminous coals. Anthracite extracts showed no effects. Contact assays using whole coal samples revealed no toxicity to D. rerio embryos in any of the coal samples, suggesting low bioavailability of PACs. In contrast, C. elegans reproduction was inhibited by direct coal contact; however, the observed toxicity probably resulted from other coal effects. The results suggest that despite the high toxic potential of PACs present, their bioavailability from different coal types is very limited and independent of coal properties and native PAH content.

Genetic toxicity of high-boiling petroleum substances

There are several specific types of high-boiling petroleum substances (HBPS) having final boiling points >343°C), in which genetic toxicity can be related to the content of polycyclic aromatic compounds (PACs), specifically crude oils, gas oils, heavy fuel oils, lubricant base oils, waxes and aromatic extracts. Evaluation of optimized Salmonella tests covering over 250 samples from 43 types of HBPS revealed that gene mutation can be determined for these substances using a protocol optimized for the detection of mutagenic PAC. The outcomes of modified Salmonella assays can be predicted using HBPS compositional information as input to a newly developed statistical model. The general outcome of the optimized Salmonella assay can be predicted for an untested substance based on its Aromatic Ring Class (ARC) profile. Review of the results from numerous cytogenetic tests showed that although a few positive study results have been reported, most HBPS do not produce chromosomal effects when tested in rodent bone marrow assays or in in vitro chromosomal aberration assays. Results of both bacterial and cytogenetic studies can be used to satisfy genetic toxicity endpoints for the HBPS category substances.