Ground-level Air Concentrations Research Articles

Burden of Disease (BoD) Assessment to Estimate Risk Factors Impact in a Real Nanomanufacturing Scenario.

An industrial nanocoating process air emissions impact on public health was quantified by using the burden of disease (BoD) concept. The health loss was calculated in Disability Adjusted Life Years (DALYs), which is an absolute metric that enables comparisons of the health impacts of different causes. Here, the health loss was compared with generally accepted risk levels for air pollution. Exposure response functions were not available for Ag nanoform. The health loss for TiO2 nanoform emissions were 0.0006 DALYs per 100,000 persons per year. Moreover, the exposure risk characterization was performed by comparing the ground level air concentrations with framework values. The exposure levels were ca. 3 and 18 times lower than the derived limit values of 0.1 μg-TiO2/m3 and 0.01 μg-Ag/m3 for the general population. The accumulations of TiO2 and Ag nanoforms on the soil top layer were estimated to be up to 85 μg-TiO2/kg and 1.4 μg-Ag/kg which was considered low as compared to measured elemental TiO2 and Ag concentrations. This assessment reveals that the spray coating process air emissions are adequately controlled. This study demonstrated how the BoD concept can be applied to quantify health impacts of nanoform outdoor air emissions from an industrial site.

EUNADICS-AV early warning system dedicated to supporting aviation in the case of a crisis from natural airborne hazards and radionuclide clouds

Abstract. The purpose of the EUNADICS-AV (European Natural Airborne Disaster Information and Coordination System for Aviation) prototype early warning system (EWS) is to develop the combined use of harmonised data products from satellite, ground-based and in situ instruments to produce alerts of airborne hazards (volcanic, dust, smoke and radionuclide clouds), satisfying the requirement of aviation air traffic management (ATM) stakeholders (https://cordis.europa.eu/project/id/723986, last access: 5 November 2021). The alert products developed by the EUNADICS-AV EWS, i.e. near-real-time (NRT) observations, email notifications and netCDF (Network Common Data Form) alert data products (called NCAP files), have shown significant interest in using selective detection of natural airborne hazards from polar-orbiting satellites. The combination of several sensors inside a single global system demonstrates the advantage of using a triggered approach to obtain selective detection from observations, which cannot initially discriminate the different aerosol types. Satellite products from hyperspectral ultraviolet–visible (UV–vis) and infrared (IR) sensors (e.g. TROPOMI – TROPOspheric Monitoring Instrument – and IASI – Infrared Atmospheric Sounding Interferometer) and a broadband geostationary imager (Spinning Enhanced Visible and InfraRed Imager; SEVIRI) and retrievals from ground-based networks (e.g. EARLINET – European Aerosol Research Lidar Network, E-PROFILE and the regional network from volcano observatories) are combined by our system to create tailored alert products (e.g. selective ash detection, SO2 column and plume height, dust cloud, and smoke from wildfires). A total of 23 different alert products are implemented, using 1 geostationary and 13 polar-orbiting satellite platforms, 3 external existing service, and 2 EU and 2 regional ground-based networks. This allows for the identification and the tracking of extreme events. The EUNADICS-AV EWS has also shown the need to implement a future relay of radiological data (gamma dose rate and radionuclides concentrations in ground-level air) in the case of a nuclear accident. This highlights the interest of operating early warnings with the use of a homogenised dataset. For the four types of airborne hazard, the EUNADICS-AV EWS has demonstrated its capability to provide NRT alert data products to trigger data assimilation and dispersion modelling providing forecasts and inverse modelling for source term estimate. Not all of our alert data products (NCAP files) are publicly disseminated. Access to our alert products is currently restricted to key users (i.e. Volcanic Ash Advisory Centres, national meteorological services, the World Meteorological Organization, governments, volcano observatories and research collaborators), as these are considered pre-decisional products. On the other hand, thanks to the EUNADICS-AV–SACS (Support to Aviation Control Service) web interface (https://sacs.aeronomie.be, last access: 5 November 2021), the main part of the satellite observations used by the EUNADICS-AV EWS is shown in NRT, with public email notification of volcanic emission and delivery of tailored images and NCAP files. All of the ATM stakeholders (e.g. pilots, airlines and passengers) can access these alert products through this free channel.

Five Years (2014–2018) of Beta Activity Concentration and the Impact of Synoptic and Local Meteorological Conditions in Bilbao (Northern Spain)

The aim of this paper is to statistically characterize gross beta activity concentrations in ground-level air in Bilbao (northern Spain) by analysing five years (2014–2018) worth of weekly measurements in aerosols collected in filters to analyse the impact of local meteorological parameters on concentrations. In addition, synoptic meteorological scenarios associated with anomalous beta surface activity concentrations were identified. Over this five-year period, beta activity concentrations ranged from 35.45 µBq/m3 to 1778 µBq/m3 with a mean of 520.12 ± 281.77 µBq/m3. A positive correlation was found with the alpha concentrations (0.67), with an average of 0.138 for the alpha/beta ratio, and a low correlation was found with 7Be (0.16). Statistical analysis identified a seasonal component in the time series, increasing, on average, beta activity concentrations from winter to autumn. The highest beta activity concentrations were measured under the arrival of southerly land winds with low wind speeds, while the wind analysis (surface winds and air masses) of two different seasonal periods (autumn 2015 and winter 2017) have highlighted how small variations in synoptic and local winds highly influence beta activity concentrations. These results are relevant to understand the meteorological factors affecting beta activity concentrations in this area and hence to define meteorological scenarios that are in favour to high/anomalous surface activity concentrations that are harmful to the environmental and public health.

Retrospective Modeling of NO2 and PM10 Concentrations over the Lyon Metropolitan Area (France), 1990–2010—Performance Evaluation, Exposure Assessment and Correlation between Pollutants

Numerous cancers develop years after subjects have been exposed to chemical compounds. Thus, environmental epidemiological studies need to accurately reconstruct exposures over long periods. To estimate exposure to NO2 and PM10 concentrations, we modelled ground-level air concentrations, at very fine temporal (1 h) and spatial (10 m) resolutions, over a large European metropolitan area and at subject’s address of a French national cohort, for five different years (1990, 1995, 2000, 2005 and 2010). Model performances were assessed by comparing the annual modelled concentration against monitoring station measurements. As input data, we used background concentrations from a large-scale dispersion model. The relevance of our approach was assessed by comparing results in 2010, with a modelling using monitoring values as background data. The comparison with measurement data showed good performance of the model for the majority of the period, with a performance declined in 1990. Concentrations at the subject’s residence decreased by 45% for PM10 and 38% for NO2. The proportion of subjects exposed above the WHO recommendations declined from 100% to 50% for PM10 and from 79% to 16% for NO2. The results of this study would provide a reference for future models to assess chronic exposures to PM10 and NO2 on a larger scale.

Analysis of Alpha Activity Levels and Dependence on Meteorological Factors over a Complex Terrain in Northern Iberian Peninsula (2014-2018).

Alpha ambient concentrations in ground-level air were measured weekly in Bilbao (northern Spain) by collecting aerosols in filters between 2014 and 2018. Over this period, the alpha activity concentrations in the aerosol’s samples range from 13.9 µBq/m3 to 246.5 µBq/m3, with a mean of 66.49 ± 39.33 µBq/m3. The inter-annual and intra-annual (seasonal and monthly) variations are analyzed, with the highest activity in autumn months and the lowest one in winter months. Special attention has been paid to alpha peak concentrations (weekly concentrations above the 90th percentile) and its relationship with regional meteorological scenarios by means of air mass trajectories and local meteorological parameters. The meteorological analysis of these high alpha concentrations has revealed two airflow patterns-one from the south with land origin and one from the north with maritime origin-mainly associated with these alpha peak concentrations. Surface winds during representative periods of both airflow patterns are also analyzed in combination with 222Rn concentrations, which demonstrated the different daily evolution associated with each airflow pattern. The present results are relevant in understanding trends and meteorological factors affecting alpha activity concentrations in this area, and hence, to control potential atmospheric environmental releases and ensure the environmental and public health.

Modelling atmospheric oxidation of 2-aminoethanol (MEA) emitted from post-combustion capture using WRF–Chem

Carbon capture and storage (CCS) is a technological solution that can reduce the amount of carbon dioxide (CO2) emissions from the use of fossil fuel in power plants and other industries. A leading method today is amine based post-combustion capture, in which 2-aminoethanol (MEA) is one of the most studied absorption solvents. In this process, amines are released to the atmosphere through evaporation and entrainment from the CO2 absorber column. Modelling is a key instrument for simulating the atmospheric dispersion and chemical transformation of MEA, and for projections of ground-level air concentrations and deposition rates. In this study, the Weather Research and Forecasting model inline coupled with chemistry, WRF–Chem, was applied to quantify the impact of using a comprehensive MEA photo-oxidation sequence compared to using a simplified MEA scheme. Main discrepancies were found for iminoethanol (roughly doubled in the detailed scheme) and 2-nitro aminoethanol, short MEA-nitramine (reduced by factor of two in the detailed scheme). The study indicates that MEA emissions from a full-scale capture plant can modify regional background levels of isocyanic acid. Predicted atmospheric concentrations of isocyanic acid were however below the limit value of 1ppbv for ambient exposure. The dependence of the formation of hazardous compounds in the OH-initiated oxidation of MEA on ambient level of nitrogen oxides (NOx) was studied in a scenario without NOx emissions from a refinery area in the vicinity of the capture plant. Hourly MEA-nitramine peak concentrations higher than 40pgm−3 did only occur when NOx mixing ratios were above 2ppbv. Therefore, the spatial variability and temporal variability of levels of OH and NOx need to be taken into account in the health risk assessment. The health risk due to direct emissions of nitrosamines and nitramines from full-scale CO2 capture should be investigated in future studies.

Assessment of potential human health and environmental impacts of a nuclear power plant (NPP) based on atmospheric dispersion modeling

The United States Environmental Protection Agency (US-EPA) short-range atmospheric dispersion model (AERMOD, v. 12345) is a good candidate for the calculation of offsite radiation doses to the general public, and its advanced capability should provide better confidence in the accuracy of offsite public doses assessment. In this paper the AERMOD code has been used to assess the impact of routine and accidental atmospheric radioactive discharges from a new nuclear power plant (NPP) site in Geregu, Nigeria (7° 33’ N, 6° 41’ E) on the four major settlements (Ajakuta, Lokoja, Idah and Okene) that lay within the emergency planning zones of the NPP. The code has produced values of the scaling factors for ground level air concentrations and depositions of radionuclides (from the passing plume) over our areas of interest. The scaling factors have been used to assess the potential radiological impact on the offsite human and non-human biota. While the radiological impacts on humans were calculated using the popular computation methods set by regulatory authorities, an integrated approach to the assessment and management of environmental risks from ionizing radiation (D-ERICA) was adopted for the non-human biota. The results of this work indicate that, under normal operations, the NPP does not pose any significant public health and environmental impacts. However, accidental conditions characterized by precipitation will lead to discernible radiological risks within the NPP sites emergency planning zone.

Temporal changes of beryllium-7 and lead-210 in ground level air in Serbia

7Be, 210Pb and 137Cs activity concentrations in ground level air at five monitoring stations (MS Vinca, Zeleno Brdo, Zajecar, Vranje and Zlatibor) in Serbia were determined during the period from May 2011. to September 2012., as part of the project monitoring of Serbia. Activity of the radionuclides in air was determined on an HPGe detector (Canberra, relative efficiency 20 %) by standard gamma spectrometry. Concentrations of cosmogenic 7Be, ranged from 1.5 to 8.8 mBq m-3 and exhibit maxima in the spring/summer period. The maximum concentrations for 210Pb were generally obtained in the fall for all investigated locations, and concentrations were in range 3.6 - 30 ? 10-4 Bq m-3. The activity concentrations of anthropogenic 137Cs in ground level air, during the observed period, were at level 0.3 - 8 ?Bq m-3. The variations in 7Be/210Pb activity ratio for the investigated stations are also presented.

Cosmogenic 7Be and 22Na in ground level air in Switzerland (1994–2011)

We report monthly averages of weekly 7Be and 22Na concentrations in aerosol samples collected with high volume aerosol filters at 5 sampling sites in Switzerland from 1994 to 2011 (7Be) and from 2000 to 2011 (22Na). Monthly average concentrations of the two cosmogenic isotopes varied between 2600 and 4600 μBq/m3 for 7Be and between 0.2 μBq/m3 and 0.5 μBq/m3 for 22Na. The 22Na concentration in ground level air strongly increased from March to May, while a corresponding 7Be increase was seen from March until July. The observed variations of the 7Be and 22Na activities together with the changes in the 7Be/22Na ratio indicate input of stratospheric air between March and May, increased mixing of upper tropospheric air from June to August, and less exchange between the upper and lower troposphere in autumn and winter. Additionally, the 11-year solar cycle is clearly seen in the annual averages of the 7Be concentrations.

Studies on the Rain Scavenging Process of Tritium in a Tropical Site at Narora in India

This study presents the results of systematic experiments on tritium (3H) concentrations in ground level air against those in rainwater near a pressurized heavy water reactor in a tropical region. The samples were collected over the rainy season of year 2011 from eight locations in the environment around Narora Atomic Power Station. The specific activity ratio of 3H between rainwater and air moisture at ground level was calculated for each data set. The average specific activity ratio was found to be ranged from 0.12 to 1.1. A correlation ( to 0.76, ) was observed between the total rain hours in a day and the rainwater 3H activity. Higher rain duration with slower rain rate yielded higher 3H concentrations as more time was available for the scavenging/wash-out process to take effect together with lower dilution. Annual tritium (HTO) wet deposition has been measured and calculated for the year 2011 within 0.8 km distance from 145 m high stack of Narora Atomic Power Station (NAPS) at nine locations in different directions. The range of deposition velocity, (m·s−1), at nine locations for the years 2011 is found to be from 4.43E − 04 to 6.42E − 03. The average value for wet deposition velocity for NAPS site is estimated as 3.17E − 03 m·s−1.

Studies on the rain scavenging process of tritium in a tropical site in India

This study presents the results of one of the first systematic experiments on tritium ( 3H) concentrations in ground level air against that in rainwater near a pressurized heavy water reactor in a tropical region. The samples were collected over the rainy season of three years (2007, 2008 and 2010). For this study, 31 data sets were collected and interpreted based on the theoretical information available in the literature. The specific activity ratio of 3H between rainwater and air moisture at ground level was calculated for each data set. The average specific activity ratio was found to be 1.96 ± 2.72. A correlation ( r = 0.82, p < 0.001) was observed between the total rain hours in a day and the rainwater 3H activity. Higher rain duration with slower rain rate yielded higher 3H concentrations as more time was available for the scavenging/wash out process to take effect together with lower dilution. The present data also suggested the need to further investigate the influence of raindrop distribution and other local meteorological parameters on the 3H wash out process. An attempt was also made to predict the 3H concentration in air moisture samples using a Gaussian plume dispersion model and the values were compared with the measured 3H activity. The measured values were generally lower than the predictions.

Determination of Symmetrical Index for 3H in Precipitation and 137Cs in Ground Level Air

The paper presents results of a long-term investigations of tritium activity concentrations in precipitation and radiocesium activity concentrations in ground level air in Belgrade, Serbia. Samples were collected at three locations in Belgrade (Meteorological Station of Belgrade MS at Zeleno Brdo (ZB), Meteorological Station MS Usek (USEK), and Vinca Institute of Nuclear Sciences (VINS)). Presented data cover the period 1985–1997. Significantly higher tritium levels were measured in samples in VINS compared with off-site location, while the impact of research reactor for 137Cs was not detected. It was found that the value of the symmetrical index n is higher for VINS in case of tritium, compared to other locations, which is in accordance with the fact that the highest average monthly concentrations of tritium were obtained in the samples from the cited place. Although the highest value of index n in case of 137Cs was also obtained for VINS, average monthly concentrations of 137Cs in ground level air for this location were the lowest. The 137Cs concentration in the ground level air is described by a kinetic equation of the first order and provides a good description of the time changes in these concentrations.

Polonium-210 and lead-210 in the terrestrial environment: a historical review

The radionuclides 210Po and 210Pb widely present in the terrestrial environment are the final long-lived radionuclides in the decay of 238U in the earth’s crust. Their presence in the atmosphere is due to the decay of 222Rn diffusing from the ground. The range of activity concentrations in ground level air for 210Po is 0.03–0.3 Bq m −3 and for 210Pb 0.2–1.5 Bq m −3. In drinking water from private wells the activity concentration of 210Po is in the order of 7–48 mBq l −1 and for 210Pb around 11–40 mBq l −1. From water works, however, the activity concentration for both 210Po and 210Pb is only in the order of 3 mBq l −1. Mosses, lichens and peat have a high efficiency in capturing 210Po and 210Pb from atmospheric fallout and exhibit an inventory of both 210Po and 210Pb in the order of 0.5–5 kBq m −2 in mosses and in lichens around 0.6 kBq m −2. The activity concentrations in lichens lies around 250 Bq kg −1, dry mass. Reindeer and caribou graze lichen which results in an activity concentration of 210Po and 210Pb of about 1–15 Bq kg −1 in meat from these animals. The food chain lichen-reindeer or caribou, and Man constitutes a unique model for studying the uptake and retention of 210Po and 210Pb in humans. The effective annual dose due to 210Po and 210Pb in people with high consumption of reindeer/caribou meat is estimated to be around 260 and 132 μSv a −1 respectively. In soils, 210Po is adsorbed to clay and organic colloids and the activity concentration varies with soil type and also correlates with the amount of atmospheric precipitation. The average activity concentration levels of 210Po in various soils are in the range of 20–240 Bq kg −1. Plants become contaminated with radioactive nuclides both by absorption from the soil (supported Po) and by deposition of radioactive fallout on the plants directly (unsupported Po). In fresh leafy plants the level of 210Po is particularly high as the result of the direct deposition of 222Rn daughters from atmospheric deposition. Tobacco is a terrestrial product with high activity concentrations of 210Po and 210Pb. The overall average activity concentration of 210Po is 13 ± 2 Bq kg −1. It is rather constant over time and by geographical origin. The average median daily dietary intakes of 210Po and 210Pb for the adult world population was estimated to 160 mBq day −1 and 110 mBq day −1, corresponding to annual effective doses of 70 μSv a −1 and 28 μSv a −1, respectively. The dietary intakes of 210Po and 210Pb from vegetarian food was estimated to only 70 mBq day −1 and 40 mBq day −1 corresponding to annual effective doses of 30.6 μSv a −1 and 10 μSv a −1, respectively. Since the activity concentration of 210Po and 210Pb in seafood is significantly higher than in vegetarian food the effective dose to populations consuming a lot of seafood might be 5–15 fold higher.

Comparison of the Industrial Source Complex and AERMOD Dispersion Models: Case Study for Human Health Risk Assessment

Air quality models are typically used to predict the fate and transport of air emissions from industrial sources to comply with federal and state regulatory requirements and environmental standards, as well as to determine pollution control requirements. For many years, the U.S. Environmental Protection Agency (EPA) widely used the Industrial Source Complex (ISC) model because of its broad applicability to multiple source types. Recently, EPA adopted a new rule that replaces ISC with AERMOD, a state-of-the-practice air dispersion model, in many air quality impact assessments. This study compared the two models as well as their enhanced versions that incorporate the Plume Rise Model Enhancements (PRIME) algorithm. PRIME takes into account the effects of building downwash on plume dispersion. The comparison used actual point, area, and volume sources located on two separate facilities in conjunction with site-specific terrain and meteorological data. The modeled maximum total period average ground-level air concentrations were used to calculate potential health effects for human receptors. The results show that the switch from ISC to AERMOD and the incorporation of the PRIME algorithm tend to generate lower concentration estimates at the point of maximum ground-level concentration. However, the magnitude of difference varies from insignificant to significant depending on the types of the sources and the site-specific conditions. The differences in human health effects, predicted using results from the two models, mirror the concentrations predicted by the models.

Health risk assessment of air emissions from a municipal solid waste incineration plant – A case study

A health risk assessment of long-term emissions of carcinogenic and non-carcinogenic air pollutants has been carried out for the municipal solid waste incinerator (MSWI) of the city of Taranto, Italy. Ground level air concentrations and soil deposition of carcinogenic (Polychlorinated Dibenzo-p-Dioxins/Furans and Cd) and non-carcinogenic (Pb and Hg) pollutants have been estimated using a well documented atmospheric dispersion model. Health risk values for air inhalation, dermal contact, soil and food ingestion have been calculated based on a combination of these concentrations and a matrix of environmental exposure factors. Exposure of the surrounding population has been addressed for different release scenarios based on four pollutants, four exposure pathways and two receptor groups (children and adults). Spatial risk distribution and cancer excess cases projected from plant emissions have been compared with background mortality records. Estimated results based on the MSWI emissions show: (1) individual risks well below maximum acceptable levels, (2) very small incremental cancer risk compared with background level.

Dispersion Modeling as a Dioxin Exposure Indicator in the Vicinity of a Municipal Solid Waste Incinerator: A Validation Study

Whether low environmental doses of dioxin affect the general population is the matter of intense debate and controversy. In a previous study, we found a 2.3-fold risk for non-Hodgkin lymphoma associated with residence in areas classified as highly exposed to dioxin emitted from a municipal solid waste incinerator (MSWI) (Besançon, France). The main limitation lay within the use of a first-generation Gaussian-type dispersion model as a proxy for dioxin exposure, since its accuracy had not been assessed before. The aim of this study was to validate this geographic-based exposure through PCDD/F measurements from soil samples. PCDD/F concentration, pH, organic carbon concentration, cation exchange capacity, and geomorphology and ecology features were assessed for 75 sampling points. In simple terrain (i.e. northeast of the MSWI), a significant association was highlighted between modeled dioxin ground-level air concentrations and log-transformed measured dioxin soil concentrations with a strong gradient across exposure categories. Conversely, in a complex topography situation (i.e. southwest of the MSWI), the model overpredicted ground-level air concentrations, particularly in the high exposure zone. First-generation modeling provided a reliable proxy for dioxin exposure in simple terrain, reinforcing the results of our case-control study. However, a more advanced atmospheric diffusion model should have been used for refined assessment in complex terrain.

A study of the movement of radioactive material discharged during the windscale fire in October 1957

In October 1957, an accident involving a fire in a nuclear reactor at Windscale Works, Sellafield, on the Cumbrian coast of England released a quantity of radioactive material into the atmosphere. Past studies have examined the resultant ground-level concentrations of radioactivity in the UK and the rest of Europe using trajectory models or the analysis of milk samples taken at the time. Presented here is the latest study into the levels of radioactivity attributed to these releases which has been undertaken using the Met Office's Nuclear Accident Model, NAME. The study examines the direction and timing of the transport, indicating the most likely spread within Europe of radioactive material from the accident. Best estimates are presented of likely time-integrated air concentrations and ground-level air concentrations of radioactivity throughout the initial few days after the accident. Although these estimates were not expected to be very accurate due to the source term being ill-defined, the results have been presented for completeness. The report concludes that NAME manages to successfully recreate the general movement of the radioactive plume and is in broad agreement with previous analyses. Discrepancies between modelled and measured plume arrival and activity for certain locations are primarily associated with errors in the calculation of the wind fields used by the model. Model predictions for this event could be improved by reducing the uncertainties in the release scenario and Met data used by NAME, and this possibility will be explored in future work.

Assessment of the radiological impacts of a zircon sand processing plant

The paper presents the results of a study on radiological impacts resulting from a zircon sand processing plant located in the North-Eastern part of Italy. Activity concentrations of radionuclides found in materials associated with this industrial process are presented as well as the results of the assessment of the annual effective doses to the workers and the members of the public. γ-Spectrometric analyses were performed on “raw” sands, end-products, and soils sampled near the plant. Thermoluminescent dosimeters, electric pumps and electret ion chambers were used to measure the external irradiation, the indoor dust concentrations and the radon concentrations, respectively. The ground-level air concentration of radioactive particulate near the plant and the deposition of particulate matter were estimated by a Gaussian model (ISCLT3). Finally, the annual effective doses, calculated as provided for by Directive 96/29/Euratom, were estimated to be 1.7 mSv y −1 for workers and 4.4 μSv y −1 for members of the public.

Prompt detection of alpha particles from 210Po: another clue to the origin of rock varnish?

Alpha particles have been measured coming from the surfaces of rocks covered with dark red-brown rock varnish, as well as rocks that appear to have little, if any, varnish. A pronounced peak at 5.3 MeV indicates the presence of 210Po, a short-lived natural-radioactive element. Surface activities for 33 samples range from 0.008 Bq/cm 2 to 0.065 Bq/cm 2. It is estimated that this nuclide is concentrated 10 11 times in these paper-thin coatings above its concentration in ground-level air. Gamma rays from the decay of 137Cs, a product of testing nuclear weapons some 50 years ago, were also detected. Analysis of samples of varnish stripped from the rock revealed traces of 239,240Pu and 238Pu. The presence of all of these isotopes strongly supports the theory that varnish films derive their building blocks from the atmosphere and, with time, all rocks in arid environments will become coated.

Monitoring ground-level air for trace analysis: methods and results.

Trace analysis enables the sensitive detection of radionuclide concentrations in ground-level air in the range of microbecquerel per cubic meter (microBq m(-3)). Typical sampling intervals of less than one day up to a few days can be used in routine operation. Trace analysis measurements are performed in the framework of the German Integrated Measuring and Information system (IMIS) and the International Monitoring System (IMS) used for verification of the Comprehensive Nuclear-Test-Ban Treaty (CTBT). Within the environmental monitoring programmes of the German IMIS the Federal Office for Radiation Protection (BfS) performs measurements of aerosol-bound radionuclides and of radioactive noble gases in the atmosphere. Aerosols are collected on filters with high-volume air samplers and analysed by gamma-spectrometry, alpha-spectrometry, and integral measurements of beta-activity, with preceding radiochemical separation. Noble gas samples from 15 sites world-wide are analysed to observe the (85)Kr-release from nuclear fuel reprocessing plants and from seven sites in Germany to monitor the (133)Xe emitted from nuclear power plants. As part of the International Monitoring System (IMS) of the CTBT an automatic aerosol sampling and measuring system and an automatic noble gas sampling and measuring system will be operated by the BfS at Mount Schauinsland near Freiburg. Because of its expertise in noble gas measurements the BfS had been chosen to perform an intercomparison experiment in the BfS laboratory in Freiburg with several automatic noble gas sampling and measurement systems before their installation at IMS sites. To establish quality-assurance programmes for trace analysis performed for the German IMIS close collaboration between the involved German institutions has been established. First steps have been taken to expand cooperation to other European laboratories. Informal data exchange already occurs between trace-analysis laboratories in Europe (Ring of Five) and helps in cases of enhanced activity concentrations to get a rapid overview of the radiological situation and to identify possible sources.