Component Of Magnetic Flux Density Research Articles

Long-period oscillations in the lower solar atmosphere prior to flare events

Multiple studies have identified a range of oscillation periods in active regions, from 3-5 minutes to long-period oscillations that last from tens of minutes to several hours. Recently, it was also suggested that these periods are connected with eruptive activity in the active regions. Thus, it is essential to understand the relation between oscillations in solar active regions and their solar eruption activity. We investigate the long-period oscillations of NOAA12353 prior to a series of C-class flares and correlate the findings with the 3- to 5-minute oscillations that were previously studied in the same active region. The objective of this work is to elucidate the presence of various oscillations with long periods in the lower solar atmosphere both before and after the flare events. To detect long-period oscillations, we assessed the emergence, shearing, and total magnetic helicity flux components from the photosphere to the top of the chromosphere. To analyze the magnetic helicity flux in the lower solar atmosphere, we used linear force-free field extrapolation to construct a model of the magnetic field structure of the active region. Subsequently, the location of long-period oscillations in the active region was probed by examining the spectral energy density of the measured intensity signal in the 1700\,AA , 1600\,AA , and 304\,AA channels of the Atmospheric Imaging Assembly (AIA) of the Solar Dynamics Observatory (SDO). Significant oscillation periods were determined by means of a wavelet analysis. Based on the evolution of the three magnetic helicity flux components, 3- to 8-hour periods were found both before and after the flare events, spanning from the photosphere to the chromosphere. These 3- to 8-hour periods were also evident throughout the active region in the photosphere in the 1700\,AA channel. Observations of AIA 1600\,AA and 304\,AA channels, which cover the chromosphere to the transition region, revealed oscillations of 3-8 hours near the region in which the flare occurred. The spatial distribution of the measured long-period oscillations mirror the previously reported distribution of 3- to 5-minute oscillations in NOAA12353 that were seen both before and after the flares. This case study suggest that the varying oscillation properties in a solar active region could be indicative of future flaring activity.

Design, scalable construction, and test of optimal linear Halbach arrays for mobile applications

Advancing permanent magnet arrays for linear electric machines is a compelling endeavor with the potential to further improve efficiencies in the fields of power generation or passenger and cargo transportation. Permanent magnets offer an unparalleled advantage by providing a consistent and efficient source of magnetic flux density without the need for external power input. This remarkable property allows for the development of smaller, lighter, and more energy-efficient electric machines, making them ideal for applications in several industries. Here, we present the design of an optimal linear Halbach array with a sinusoidal distribution of the magnetic flux density component Bz perpendicular to the surface of the array. A large scale and easy scalable six-segmented Halbach array has been built without the use of a steel backplate enabling a lightweight and compact design. Numerical results of the magnetic flux density distributions are calculated by relying on finite element methods and are compared with experimental measurements of the magnetic flux density, showing good agreement. The demonstration revealed that, with an optimal magnet configuration, the absence of a backplate does not result in any diminishment of magnetic flux density strength.

2D Analytical Calculation of the Open Circuit Electromagnetic Field Distribution in an Axial Flux Slotted Permanent Magnet Machine using Fourier Analysis.

The paper presents an analytical method in order to obtain the electromagnetic field distribution in an axial flux slotted permanent magnet machine under no-load conditions. The method solves the Laplace equation in the gap of an slotted machine via magnetic scalar potential. Once the magnetic scalar potential is defined, the magnetic flux density components are computed.. Results issued from the proposed model are compared with those stemming from a 3D finite-element method (FEM) simulation. In addition to permanent magnet machines, this technique can be applied to any 2D geometry with the restriction that the geometry should consist of rectangular regions.

Stator Core Loss Analysis and Suppression of Permanent Magnet Vernier Machines

Permanent magnet vernier machine is a new type of permanent magnet machine, which is operated based on flux modulation effect. In this paper, the stator core loss of the permanent magnet vernier machine is investigated based on the relationship of the stator core loss to harmonic components of the airgap magnetic flux density crossing airgap and leakage flux not crossing airgap. In this manner, the stator core loss can be analyzed with consideration of flux modulation effect and flux modulation pole structure. First, stator core losses generated by magnetic fields of permanent magnet and armature winding are analyzed. Then, stator tooth fluxes coming from airgap magnetic flux and leakage flux are derived. Also, non-working stator tooth flux contributing stator core loss but not contributing torque is identified. Based on this, two approaches to suppress the stator core loss of the permanent magnet vernier machine are proposed. Finally, the effectiveness of the stator core loss analysis and suppression is verified by finite element analysis and experiments.

Magnetic field patterns as a tool for stress estimation in steel samples

In this work, steel square samples were subjected to varying degrees of compression, resulting in a distribution of simultaneous compressive and tensile stresses within the samples. The tangential component of the surface magnetic flux density was mapped along both the direction of compression and perpendicular to it, using a magnetic sensor, for each level of compression. The results show that the maps of the relative difference of magnetic flux density for different levels of applied stress, with respect to the flux density at zero stress, exhibited a diagonal stripes pattern. This pattern was discovered thanks to the particular surface stress distribution in square samples. The formation of these patterns could be attributed to the re-orientation of magnetic domains due to stress and the magneto-elastic effect, which was confirmed by the change in orientation of the magnetic flux density vectors obtained from the measurement of two of their components. Additionally, the maps showed an increase in contrast between high and low values with an increase in applied stress. Finally, the maps of the module of the gradient of magnetic flux density displayed a distinct diagonal chessboard-like pattern, and the contrast between low and high values increased with an increase in applied stress.

Preferable PMSM rotor geometry for reduced axial flux components in the stator core

This paper describes various rotor geometries for the axial end region of permanent magnet synchronous machines (PMSMs) with the aim of reducing the axial magnetic stator flux component. This is achieved by considering the degrees of freedom for the three-dimensional geometry provided by state-of-the-art manufacturing technologies. The comparison of various approaches against conventional arrangements is discussed based on the effects on the axial magnetic stator flux in the end region and on the magnetic flux within the air-gap.

A review on analytical models of brushless permanent magnet machines

AbstractThis study provides an in‐depth investigation of the use of analytical and numerical methods in analyzing electrical machines. Although numerical models such as the finite‐element method (FEM) can handle complex geometries and saturation effects, they have significant computational burdens, are time‐consuming, and are inflexible when it comes to changing machine geometries or input values. Analytical models based on magnetic equivalent circuits (MEC) or solving Maxwell's equations can be faster and more flexible, but less accurate for complex machine structures. The paper focuses on the recent development of analytical models for brushless permanent‐magnet (PM) machines that have become increasingly popular in low and medium‐power applications. The literature review covers the recent developments in analytical models for PM machines with respect to various machine quantities such as magnetic flux density components, induced voltage, inductances, electromagnetic force/torque, efficiency, or unbalanced magnetic force (UMF). It outlines the advantages and disadvantages of different analytical models such as the zero‐dimensional (0‐D), one‐dimensional (1‐D), two‐dimensional (2‐D), and three‐dimensional (3‐D) analytical methods, as well as the Maxwell and basic mathematical analysis. Although the MEC models are faster than the numerical model, they are not as accurate for various structures of electrical machines including a great magnetic air gap. They also note that the analytical models based on the Maxwell equations are faster than the numerical ones and have the potential to obtain acceptable accuracy similar to the numerical models in electrical machines. Overall, this literature review provides valuable insights for researchers and engineers in selecting appropriate analytical models for PM machines. It highlights the trade‐offs between accuracy and computational efficiency when choosing between numerical and analytical models, and the flexibility of analytical models to address changes in machine geometries or input values. Additionally, this helps researchers save time in determining appropriate references regarding the analytical models of brushless PM machines.

Development of the CMS Magnetic Field Map

This article focuses on pioneering work on the performance of the three-dimensional (3D) magnetic field map in the entire volume of the Compact Muon Solenoid (CMS) detector at the Large Hadron Collider at CERN. In the CMS heterogeneous magnetic system, the magnetic flux is created by a superconducting solenoid coil enclosed in a steel flux-return yoke. To describe the CMS magnetic flux distribution, a system of the primitive 3D volumes containing the values of the magnetic flux density measured inside the superconducting coil inner volume and modelled outside the coil across a special mesh of reference nodes was developed. This system, called the CMS magnetic field map, follows the geometric features of the yoke and allows the interpolation of the magnetic flux density between the nodes to obtain the magnetic field values at any spatial point inside a cylinder of 18 m in diameter and 48 m in length, where all the CMS sub-detectors are located. The geometry of the volumes is described inside one 30° azimuthal sector of the CMS magnet. To obtain the values of the magnetic flux density components across the entire azimuth angle of the CMS detector, rotational symmetry is applied.

트랙션용 다자유도 구형 전동기의 구동을 위한 간접 벡터 제어 연구

The multi-degree-of-freedom spherical motor for traction has characteristics of rotation and steering. Although it is base on the rotation principle of an induction motor, only a spherical motor control method is required for rotation and steering. In order to estimate the speed command of the rotor, the mechanical angular velocity of the rotor is measured using an optical sensor, and the slip angular velocity is calculated with the current command of the d-q axis stator of the synchronous coordinate system. The rotor magnetic flux angle can be obtained in the above two ways, and through this, the vector control of the spherical motor is achieved. The desired magnetic flux component current and torque component current are distributed to operate the spherical motor. As such, the indirect vector control method has advantages in that it is simple to implement because it does not use the magnetic flux linkage of the rotor and that it is easy to operate from low speed to rated speed.

Computational analysis of conductive fluid flow with tangential components of magnetic flux density and electric field in metallic and non-metallic circular pipe

This paper has focused on the study of flow characteristics of a steady conductive fluid through a circular pipe in the presence of an applied transverse uniform magnetic field. A numerical simulation of the fluid flow was performed using a multi-physics computational tool. The radial velocity distribution due to the effect of the tangential component of induced magnetic flux density and electric fields at various axial positions is examined in metallic and non-metallic surfaces of the circular pipe. This simulation study helps to analyse the effect of drag force on the variation in axial velocity close to the metallic and non-metallic walls. The induced electric potential is directed along the normal to the Laplacian tangential surface of the pipe. In addition to that, sigmoidal-shaped field profiles are observed when the fluid flow crosses from the upstream to downstream of the magnet edge and vice versa along the axial length of the circular pipe. Simultaneously, it is observed that the average velocity of the fluid flow decreases for a laminar and increases for turbulent Reynolds number. Streamline plots pertinent flow variable such as flow velocity are presented for non-conducting and conducting walls.

Characteristics of electromagnetic vector field generated from rock fracturing

Rock fracturing is often accompanied by electromagnetic phenomenon. As a vector field, in addition to the intensity that is widely concerned, the generated electromagnetic field also has obvious directionality. To this end, a set of electromagnetic antennas capable of simultaneous three-axis measurement is used to monitor the electromagnetic vector field generated from rock fracturing based on Brazilian tests. The signal amplitude on each axis can represent the magnitude of actual magnetic flux density component on the three axes. The intensity and directional characteristics of electromagnetic signals received at different positions are studied using vector synthesis. The directionality of electromagnetic radiation measured using a three-axis electromagnetic antenna shows that the direction of the magnetic flux intensity generated by rock fracturing tends to be parallel to the crack surface, and the measured signal intensity is greater in a direction closer to the crack surface.

Theoretical Predictions of Perturbed Magnetic Flux Density Components Due to Narrow Flaws in ECT

This work proposes a semianalytical technique based on the boundary element method (BEM) to predict the signals due to flaws (cracks) that are typically encountered in eddy current (ECT) nondestructive testing (NDT). Two case studies, for two different narrow opening notches in a finite thickness aluminium plate, were performed by experimental measurements to corroborate the theoretical model. The signal which has been modelled is the perturbation in the magnetic flux density (MFD) components <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">B_x</i> , <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">B_y</i> , and <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">B_z</i> due to narrow opening flaws. The proposed analytical model uses the magnetic vector potential (MVP), arising from electric dipole sources, to determine the voltage induced in a hypothetical small circular loop located around the evaluation point. Based on the linear relationship between the voltage induced and the magnetic flux in the surface enclosed by the hypothetical loop, a linearity constant that transforms the induced voltage to the MFD component has been computed. Appropriate vector potential Green’s functions have been used to transform the electric dipole sources to the magnetic vector potential components to determine the voltage induced in the hypothetical loop.

REBCO Trapezoidal Armature Windings for Superconducting Induction Motors

For extensive use in electric vehicles, electric airplanes, and other such applications, superconducting motors are designed to be lightweight and have a high power density. Rare-earth barium copper oxide (REBCO) tapes are considered a potential material for use in these motors because of their high critical current density. Because REBCO can be modeled into tape shapes, motors with racetrack coils as armature windings have been studied. However, racetrack coils are inferior in terms of increasing the interlinkage flux to the rotor compared with distributed windings. In this study, we propose trapezoidal REBCO tape coils for shaping armature windings into distributed windings. Next, 2 kW-class induction motors using two types of coils—the trapezoidal and racetrack coils—were designed to compare the characteristics of the two motors. The JMAG-Designer software was used to perform electromagnetic simulations on the two models. The results revealed that the motor with trapezoidal coils required less REBCO tapes and exhibited a lower vertical component of magnetic flux density than the racetrack coils did. Therefore, the AC loss of the trapezoidal coils becomes lower than that of the racetrack coils, and the trapezoidal coils weigh less than racetrack coils.

Magnetic Field and Radial Force Analysis of Six-Phase Rotary Machine

Six-phase permanent magnet synchronous machine and the control system are also widely used in industry, precision instruments and aerospace. However, most PMSMs employ magnet patterns either in alternatively radial magnetization or Halbach array, which may constrain the performance improvement in a certain degree. Therefore, a novel six-phase trapezoidal Halbach magnet array (THMA) is proposed in this paper. Six-phase permanent magnet synchronous machines (PMSMs) can reduce the harmonic components of magnetic flux in air gap, and decrease the iron loss and electromagnetic vibration caused by harmonic torque. Thus, it helps to improve the working efficiency and depress the torque ripple of the electrical machine. Dual three-phase windings are employed for the stator design to further improve the power density and reliability of the machine. Six-phase vector model of the machine is built based on dual dq control. It can minimize the electric coupling, magnetic coupling and thermal coupling. The radial electromagnetic force of the machine under load or no load is extracted, then the harmonic decomposition of the radial electromagnetic force for the spatial with time Fourier decomposition is carried out to obtain the force amplitude of different orders which is conducive to analyze the vibration characteristics of the machine.

Automatic defect identification in magnetic particle testing using a digital model aided De-noising method

Magnetic particle testing (MPT) has high sensitivity, which is popular in ferromagnetic material detection. However, results of MPT always mix with fake magnetic particle indication (FMPI) and point noise caused by nonrelevant magnetic particles. It mainly depends on manual work to find defects in MPT. In this paper, Hough Transform, which is robust to the point noise, is introduced to automatically identify the linear features of magnetic particle indication (MPI) caused by defects. However, the algorithm cannot distinguish between the similarly shaped FMPI and MPI. To address the problem, we proposed a digital model aided de-noising Method. Specifically, the density of normal component of magnetic flux on specimen surface is calculated by finite element analysis to evaluate the possibilities of FMPI occurrence. Then detection results are compared with the calculation to eliminate FMPI. Experiments show that scratches on hub bearing can be successfully identified by the proposed method.

Surface and back-side defects identification combined with magnetic flux leakage and boundary magnetic perturbation.

In magnetic flux leakage (MFL) detection, the identification of surface and back-side defects is required to obtain more accurate defect quantification and risk assessment results. However, current MFL techniques can detect both surface and back-side defects but are generally unable to distinguish between them. Therefore, this paper proposes a new boundary magnetic perturbation (BMP) testing method, combining the results of MFL to distinguish between surface and back-side defects. First, the detection mechanism of the BMP testing method and the impact of the tested magnetic flux density components are presented and analyzed by simulations to further develop an identification method. Then, the influences of the BMP sensor's lift-off and installation position are investigated by experiments to improve distinguishing performance. Finally, the repeated measurements show that the surface and back-side defects within the wide range of sizes can be identified accurately, even when the defect depths are in the range of 12.5%-87.5% of the sample thickness. Furthermore, the BMP testing method neither increases the length of the detection device nor requires additional magnetizers or signal generators. Therefore, the proposed method is highly suitable for the existing MFL detection devices to distinguish between surface and back-side defects.

Measurement and Exposure Assessment of Intermediate Frequency Magnetic Fields From Electronic Article Surveillance (EAS) Gates in Libraries.

Exposure to magnetic fields from the electronic article surveillance (EAS) gate was evaluated in consideration of the application to epidemiological studies of library workers who are exposed continually to intermediate frequency magnetic fields from the EAS gate. Two types of exposures were investigated. One was transient exposure due to passing through or beside the gate and another was chronic exposure in the room. We measured magnetic fields from five EAS gate models which were commonly used in libraries in Japan. Detailed measurements were performed for two of them in consideration of the phase difference of vector components of magnetic flux density. The polarization of the magnetic field in the gate was investigated with the index of ellipticity. The induced electric field in a human body was numerically calculated for exposures to magnetic fields of the two gate models. The results provide a quantitative understanding of exposures during passing through or by the EAS gate. Magnetic field distribution was measured in a large room for one gate model to quantify the chronic exposure of library workers during the work at the desk. It was found that the magnetic field was distributed as a function of the horizontal distance to the nearest gatepost. The 45-point average value BIEC defined by the IEC standard was suggested to be a useful quantity to characterize the magnitude of the magnetic field from the EAS gate. Exposures to different EAS gates are expected to be compared through this quantity without detailed measurements. These results are expected to provide useful means for exposure assessment of epidemiological studies on the association between the IF-EMF exposure and possible health outcomes.

On the Differences in the Periodic Behavior of Magnetic Helicity Flux in Flaring Active Regions with and without X-class Events

Abstract Observational precursors of large solar flares provide a basis for future operational systems for forecasting. Here, we study the evolution of the normalized emergence (EM), shearing (SH), and total (T) magnetic helicity flux components for 14 flaring (with at least one X-class flare) and 14 nonflaring (&lt;M5-class flares) active regions (ARs) using the Space-weather Helioseismic Magnetic Imager Active Region Patches vector magnetic field data. Each of the selected ARs contain a δ-type spot. The three helicity components of these ARs were analyzed using wavelet analysis. Localized peaks of the wavelet power spectrum (WPS) were identified and statistically investigated. We find that (i) the probability density function of the identified WPS peaks for all the EM/SH/T profiles can be fitted with a set of Gaussian functions centered at distinct periods between ∼3 and 20 hr. (ii) There is a noticeable difference in the distribution of periods found in the EM profiles between the flaring and nonflaring ARs, while no significant difference is found in the SH and T profiles. (iii) In flaring ARs, the distributions of the shorter EM/SH/T periods (&lt;10 hr) split up into two groups after flares, while the longer periods (&gt;10 hr) do not change. (iv) When the EM periodicity does not contain harmonics, the ARs do not host a large energetic flare. (v) Finally, significant power at long periods (∼20 hr) in the T and EM components may serve as a precursor for large energetic flares.

The Nonzero External Magnetic Field of Long Solenoids

A widespread assertion has existed for a long time, believing the external field of an infinitely long solenoid should be zero, but it is proofed to be wrong in this work. The components of magnetic flux density of current-carrying, closely wound cylindrical solenoids are calculated. At a distant field point, the external field definitely has a nonzero component, being equal to that of a straight wire of equal length. Since this equivalence is length-independent, it still holds true for ideal solenoids having infinite length. Hence the incorrect and still spreading inference about long solenoids should be rectified. Furthermore, theoretical and experimental discussions involving solenoids should be reviewed again carefully.

Comparative study between E-shaped and Fan-shaped Electromagnetic Guideway for HTS maglev

Permanent magnet guideway (PMG) has commonly been used for HTS maglev system so far. In some previous studies, electromagnetic guideway (EMG) was proved to have some advantages in practical HTS maglev construction.EMGs with different geometries produce different magnetic field distributions and have different operation performances in HTS maglev system. In this study, comparative experiments of E-shaped and Fan-shaped EMG prototypes have been conducted under the same condition of vertical direction component of magnetic flux density (Bz), power consumption (P), and total magnetic potential (F). The experimental results were compared and discussed, and a 2D finite element simulation model was used to explain and analyze the experimental phenomenon more deeply under condition of the same F. These results may be helpful for further development of EMG for HTS maglev applications and explaining the regularities of levitation and guidance force in principle.