Common Microscopy Techniques Research Articles

Spatially-coded Fourier ptychography: flexible and detachable coded thin films for quantitative phase imaging with uniform phase transfer characteristics.

Fourier ptychography (FP) is an enabling imaging technique that produces high-resolution complex-valued images with extended field coverages. However, when FP images a phase object with any specific spatial frequency, the captured images contain only constant values, rendering the recovery of the corresponding linear phase ramp impossible. This challenge is not unique to FP but also affects other common microscopy techniques -- a rather counterintuitive outcome given their widespread use in phase imaging. The underlying issue originates from the non-uniform phase transfer characteristic inherent in microscope systems, which impedes the conversion of object wavefields into discernible intensity variations. To address this challenge, we present spatially-coded Fourier ptychography (scFP), a new method that synergizes FP with spatial-domain coded detection for true quantitative phase imaging. In scFP, a flexible and detachable coded thin film is attached atop the image sensor in a regular FP setup. The spatial modulation of this thin film ensures a uniform phase response across the entire synthetic bandwidth. It improves reconstruction quality and corrects refractive index underestimation issues prevalent in conventional FP and related tomographic implementations. The inclusion of the coded thin film further adds a new dimension of measurement diversity in the spatial domain. The development of scFP is expected to catalyse new research directions and applications for phase imaging, emphasizing the need for true quantitative accuracy with uniform frequency response.

Breaking the Time Barrier in Kelvin Probe Force Microscopy: Fast Free Force Reconstruction Using the G-Mode Platform.

Atomic force microscopy (AFM) offers unparalleled insight into structure and material functionality across nanometer length scales. However, the spatial resolution afforded by the AFM tip is counterpoised by slow detection speeds compared to other common microscopy techniques (e.g., optical, scanning electron microscopy, etc.). In this work, we develop an ultrafast AFM imaging approach allowing direct reconstruction of the tip-sample forces with ∼3 order of magnitude higher time resolution than is achievable using standard AFM detection methods. Fast free force recovery (F3R) overcomes the widely viewed temporal bottleneck in AFM, that is, the mechanical bandwidth of the cantilever, enabling time-resolved imaging at sub-bandwidth speeds. We demonstrate quantitative recovery of electrostatic forces with ∼10 μs temporal resolution, free from influences of the cantilever ring-down. We further apply the F3R method to Kelvin probe force microscopy (KPFM) measurements. F3R-KPFM is an open loop imaging approach (i.e., no bias feedback), allowing ultrafast surface potential measurements (e.g., <20 μs) to be performed at regular KPFM scan speeds. F3R-KPFM is demonstrated for exploration of ion migration in organometallic halide perovskite materials and shown to allow spatiotemporal imaging of positively charged ion migration under applied electric field, as well as subsequent formation of accumulated charges at the perovskite/electrode interface. In this work, we demonstrate quantitative F3R-KPFM measurements-however, we fully expect the F3R approach to be valid for all modes of noncontact AFM operation, including noninvasive probing of ultrafast electrical and magnetic dynamics.

Substrate-Deposited Sea Spray Aerosol Particles: Influence of Analytical Method, Substrate, and Storage Conditions on Particle Size, Phase, and Morphology.

Atmospheric aerosols are often collected on substrates and analyzed weeks or months after the initial collection. We investigated how the selection of substrate and microscopy method influence the measured size, phase, and morphology of sea spray aerosol (SSA) particles and how sample storage conditions affect individual particles using three common microscopy techniques: optical microscopy, atomic force microscopy, and scanning electron microscopy. Micro-Raman spectroscopy was used to determine changes in the water content of stored particles. The results show that microscopy techniques operating under ambient conditions provide the most relevant and robust measurement of particle size. Samples stored in a desiccator and at ambient conditions leads to similar sizes and morphologies, while storage that involves freezing and thawing leads to irreversible changes due to phase changes and water condensation. Typically, SSA particles are deposited wet and, if possible, samples used for single-particle analysis should be stored at or near conditions at which they were collected in order to avoid dehydration. However, if samples need to be dry, as is often the case, then this study found that storing SSA particles at ambient laboratory conditions (17-23% RH and 19-21 °C) was effective at preserving them and reducing changes that would alter samples and subsequent data interpretation.

Versatile optical manipulation system for inspection, laser processing, and isolation of individual living cells

Isolation of individual cells from a heterogeneous cell population is an invaluable step in the analysis of single cell properties. The demands in molecular and cellular biology as well as molecular medicine are the selection, isolation, and monitoring of single cells and cell clusters of biopsy material. Of particular interest are methods which complement a passive optical or spectroscopic selection with a variety of active single cell processing techniques such as mechanical, biochemical, or genetic manipulation prior to isolation. Sophisticated laser-based cell processing systems are available which can perform single cell processing in a contact-free and sterile manner. Until now, however, these multipurpose turnkey systems offer only basic micromanipulation and are not easily modified or upgraded, whereas laboratory situations often demand simple but versatile and adaptable solutions. We built a flexible laser micromanipulation platform combining contact-free microdissection and catapulting capabilities using a pulsed ultraviolet (337nm) laser with simultaneous generation of optical tweezing forces using a continuous wave infrared (1064nm) laser. The potential of our platform is exemplified with techniques such as local laser-induced injection of biomolecules into individual living cells, laser surgery, isolation of single cells by laser catapulting, and control of neuronal growth using optical gradient forces. Arbitrary dynamic optical force patterns can be created by fast laser scanning with acousto-optical deflectors and galvanometer mirrors, allowing multibeam contact-free micromanipulation, a prerequisite for reliable handling of material in laboratory-on-a-chip applications. All common microscopy techniques can be used simultaneously with the offered palette of micromanipulation methods. Taken together, we show that advanced optical micromanipulation systems can be designed which combine quality, cost efficiency, and adaptability.