Commercial Off-the-shelf Devices Research Articles

Reliability risk analysis and control strategy of COTS devices in aviation equipment

With the rapid advancement of aviation equipment, the adoption of commercial off-the-shelf (COTS) devices in aviation equipment has witnessed a substantial rise. As these devices are not specifically designed for aviation equipment with high safety and reliability requirements, their widespread use may give rise to numerous challenges and issues. Therefore, conducting reliability risk analysis and control of COTS devices is crucial for ensuring the performance and reliability of aviation equipment. This paper examines the fundamental conditions and current issues regarding the test and evaluation work of COTS products in U.S. military aviation equipment. Furthermore, it conducts a thorough analysis of the reliability risks associated with COTS devices in aviation equipment. Subsequently, a strategy and procedure for managing reliability risks related to COTS devices in aviation equipment is proposed. The results of the application case analysis demonstrate the effectiveness of the proposed method in identifying and capturing the key factors associated with the reliability risk of COTS devices. This subsequently guides the assessment and control of reliability risks associated with COTS devices in aviation equipment.

RF Systems on Chip and Mixed-Signal Front-End Devices: Game-Changing RF Technologies for Space Applications

Growing interest in the commercialization of space (NewSpace) is leading to increased acceptance of commercial off-the-shelf (COTS) electronics and thus enabling use in space of the latest technologies developed for terrestrial applications. This opens new capabilities for applications in space missions. RF communication via satellites has been established for decades; traditionally used for military applications, it is becoming increasingly important for commercial users. Today, global connectivity and access to the Internet has never been so important, and the demand for worldwide connectivity increases significantly each year. Space-based Internet access is especially important for areas with poor terrestrial infrastructure, such as Africa and Antarctica. There are already geostationary-Earth orbit (GEO)-stationary-located satellites available such as <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">Inmarsat</i> or low-Earth orbit (LEO) satellite constellations like Iridium, which provide almost-global access to the Internet, but they are either very expensive or have low data rates and long latencies, so they are not very attractive. New solutions with high data rates, low latencies, and affordable fees are currently in development, such as StarLink, with its giga constellation <xref ref-type="bibr" rid="ref1" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">[1]</xref> , <xref ref-type="bibr" rid="ref2" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">[2]</xref> , and Amazon’s Project Kuiper <xref ref-type="bibr" rid="ref3" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">[3]</xref> , <xref ref-type="bibr" rid="ref4" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">[4]</xref> , <xref ref-type="bibr" rid="ref5" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">[5]</xref> . So it is true: there really has been a change in the market with the NewSpace Era. With NewSpace, or in other words, the commercialization of space, traditional space missions with high-quality assurance requirements, very long design and manufacturing times, and extraordinary costs may become obsolete at a certain point, at least when it comes to commercial services like satellite-based Internet access. To decrease the lead time and costs of such missions, satellite designers and manufacturers need to rely on commercially available electronics, namely, COTS devices, which are usually much cheaper and have better performance and shorter lead times compared to space-qualified parts. In terms of performance, COTS devices have great benefits over space-qualified parts simply because the design, development, and qualification processes for space parts are very complex and take years before they are qualified and available for the market. It is likely that state-of-the-art space-qualified parts are 10 years behind what we currently have available for terrestrial applications, such as for the automotive or industrial markets <xref ref-type="bibr" rid="ref6" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">[6]</xref> . One obvious reason is certainly that electronic parts manufacturers develop products for certain markets, and space is yet not one of the biggest or most attractive markets. But this has already started changing and big players such as Texas Instruments and Analog Devices are moving forward with the NewSpace wave and establishing ever-more products for commercial space applications. Truly, using state-of-the art electronics is not only of interest for the space-based Internet, there are also other space-related applications that can clearly benefit from using the latest technologies.

UltraMotion: High-precision Ultrasonic Arm Tracking for Real-world Exercises

Home exercise and self-served gyms allow a larger population to exercise regularly without the cost of hiring private coaches. In absence of professional guidance, however, exercisers can suffer from injuries to muscles and joints. High-precision, affordable arm tracking with commercial, off-the-shelf (COTS) wearable devices has become an urgent need to prevent workout injuries and improve exercise performance. Recent studies with inertial measurement units (IMUs) or audio signals are neither computationally feasible for real-time motion tracking with satisfactory accuracy using COTS devices nor practically usable due to the interference with noisy ambient environments. In this paper, we propose UltraMotion, a real-time, high-precision ultrasonic arm motion tracking system designed for practical use. UltraMotion performs point cloud queries based on hidden Markov models (HMMs), a novel ultrasonic acoustic ranging method, and an extended Kalman filter (EKF) to predict the locations of all three arm joints, making it the first system offering shoulder locations. Experimental results with only a smartphone and a smartwatch demonstrate the effectiveness of UltraMotion in tracking shoulder, elbow, and wrist locations with impressively small median errors of 6.4 cm, 7.1 cm, and 8.5 cm in real-world environments, outperforming all previous systems, making UltraMotion an ideal choice for daily exercise.

Multistatic UWB Radar-Based Passive Human Tracking Using COTS Devices

Due to its high delay resolution, the ultra-wideband (UWB) technique has been widely adopted for fine-grained indoor localization. Instead of active positioning, UWB radar-based passive human tracking is explored using commercial off-the-shelf (COTS) devices. To extract the time-of-flight (ToF) reflected by the moving person, the accumulated channel impulse responses (CIR) and the corresponding variances are used to train the convolutional neural networks (CNN) model. Particle filter algorithm is adopted to track the moving person based on the extracted ToFs of all pairs of links. Experimental results show that the proposed CIR- and variance-based CNN models achieve less than 30-cm root-mean-square errors (RMSEs). Especially, the variance-based CNN model is robust to the scenario changing and promising for practical applications.

Risk Assessment for the Use of COTS Devices in Space Systems under Consideration of Radiation Effects

In this paper, a new approach is presented to assess the risk of using commercial off-the-shelf (COTS) devices in space systems under consideration of radiation effects that can dramatically affect reliability and performance. In the NewSpace era, the use of COTS has become mandatory, since typical space-qualified (class-1) electrical, electronic and electromechanical (EEE) components for space missions are no longer attractive due to their extremely high costs, long lead times and low performance. This paper sets out the usual constraints for COTS devices and proposes a guideline on how to select non-space-qualified components and when class-1 EEE devices are recommended for use.

Assessing the Accuracy of Popular Commercial Technologies That Measure Resting Heart Rate and Heart Rate Variability.

Commercial off-the shelf (COTS) wearable devices continue development at unprecedented rates. An unfortunate consequence of their rapid commercialization is the lack of independent, third-party accuracy verification for reported physiological metrics of interest, such as heart rate (HR) and heart rate variability (HRV). To address these shortcomings, the present study examined the accuracy of seven COTS devices in assessing resting-state HR and root mean square of successive differences (rMSSD). Five healthy young adults generated 148 total trials, each of which compared COTS devices against a validation standard, multi-lead electrocardiogram (mECG). All devices accurately reported mean HR, according to absolute percent error summary statistics, although the highest mean absolute percent error (MAPE) was observed for CameraHRV (17.26%). The next highest MAPE for HR was nearly 15% less (HRV4Training, 2.34%). When measuring rMSSD, MAPE was again the highest for CameraHRV [112.36%, concordance correlation coefficient (CCC): 0.04], while the lowest MAPEs observed were from HRV4Training (4.10%; CCC: 0.98) and OURA (6.84%; CCC: 0.91). Our findings support extant literature that exposes varying degrees of veracity among COTS devices. To thoroughly address questionable claims from manufacturers, elucidate the accuracy of data parameters, and maximize the real-world applicative value of emerging devices, future research must continually evaluate COTS devices.

Deep Space In Situ Imaging Results of Commercial Off-the-Shelf Visual Monitoring System Aboard the Hayabusa2 Spacecraft

Visual images are effective tools for monitoring the condition of spacecraft. In this article, we developed a low-cost, low impact, compact visual monitoring system using commercial off-the-shelf (COTS) devices to perform critical situation monitoring of the Hayabusa2 touchdown mission. The in situ performance of all devices for the touchdown mission, such as the field programmable gate array, complementary metal oxide semiconductor image sensor, analog decoder, and first-in-first-out memory, was examined in terms of the image capturing time and the tuning of image sensors. The in situ image capturing results indicated that these devices can be successfully used in deep space applications. Our findings can provide a reference for the use of COTS devices in deep space applications.

In-Band Secret-Free Pairing for COTS Wireless Devices

Many IoT devices lack the necessary interfaces (keyboards, screens) for entering passwords or changing default ones. For these devices, bootstrapping trust can be challenging. We address the problem of device pairing in the absence of any shared secrets. Pairing is a two-phase process that requires mutual authentication between the two parties and the agreement to a common key that can be used to further bootstrap essential cryptographic mechanisms. We propose a secret-free and in-band trust establishment protocol that achieves the secure pairing of commercial off-the-shelf (COTS) wireless devices with a hub. As compared to the state-of-the-art, our protocol does not require any hardware/firmware modification to the devices, or any out-of-band channels, but can be applied to any COTS device. Furthermore, our protocol is resistant to active signal manipulations attacks that include recently demonstrated signal nullification at an intended receiver. These security properties are achieved in-band with the assistance of a helper device such as a smartphone and by exploiting hard-to-forge signal propagation laws. We perform extensive theoretical analysis to verify the security of the proposed protocol. In addition, we validate our theoretical results with experiments using COTS devices and USRP radios.

Thermal neutrons: a possible threat for supercomputer reliability

The high performance, high efficiency, and low cost of Commercial Off-The-Shelf (COTS) devices make them attractive for applications with strict reliability constraints. Today, COTS devices are adopted in HPC and safety-critical applications such as autonomous driving. Unfortunately, the cheap natural boron widely used in COTS chip manufacturing process makes them highly susceptible to thermal (low energy) neutrons. In this paper, we demonstrate that thermal neutrons are a significant threat to COTS device reliability. For our study, we consider two DDR memories, an AMD APU, three NVIDIA GPUs, an Intel accelerator, and an FPGA executing a relevant set of algorithms. We consider different scenarios that impact the thermal neutron flux such as weather, concrete walls and floors, and HPC liquid cooling systems. Correlating beam experiments and neutron detector data, we show that thermal neutrons FIT rate could be comparable or even higher than the high energy neutron FIT rate.

Pushing the Data Rate of Practical VLC via Combinatorial Light Emission

Visible light communication (VLC) systems relying on commercial-off-the-shelf (COTS) devices have gathered momentum recently, due to the pervasive adoption of LED lighting and mobile devices. However, the achievable throughput by such practical systems is still several orders below those claimed by controlled experiments with specialized devices. In this paper, we engineer CoLight aiming to boost the data rate of the VLC system purely built upon COTS devices. CoLight adopts COTS LEDs as its transmitter, but it innovates in its simple yet delicate driver circuit wiring an array of LED chips in a combinatorial manner. Consequently, modulated signals can directly drive the on-off procedures of individual chip groups, so that the spatially synthesized light emissions exhibit a varying luminance following exactly the modulation symbols. To obtain a readily usable receiver, CoLight interfaces a COTS PD with a smartphone through the audio jack, and it also has an alternative MCU-driven circuit to emulate a future integration into the phone. The evaluations on CoLight are both promising and informative: they demonstrate a throughput up to 80 kbps at a distance of 2 m, while suggesting various potentials to further enhance the performance.

Reliable and Low-Complexity Chirp Spread Spectrum-Based Aerial Acoustic Communication

Aerial acoustic communication (AAC) has been developed for a variety of Internet-of-things (IoT) applications, thanks to the merit of embedding small amounts of data directly into audio contents and transmitting them through commercial off-the-shelf (COTS) devices without additional infrastructure. However, AAC has clear limitations due to ambient noise, severely frequency-selective acoustic channels, and high power consumption of COTS devices. We adopt chirp spread spectrum (CSS) modulation and design new quaternary symbols to overcome frequency selectivity of audio interfaces of COTS devices. We also develop a computation-efficient method to demodulate the proposed symbols, aiming to reduce the power consumption of COTS devices. We employ a frame combining technique without increasing computational complexity, to mitigate the effects of multipath fading and ambient noise in acoustic channels. To evaluate the proposed methods, we conduct extensive experiments with several smartphones in various environments. The experimental results and evaluation demonstrate that the proposed symbols and frame combining method contribute to improving the frame reception ratio by up to 59.8%p (267.9%) and 14%p (84.3%), respectively. The frame combining increases the possibility of receiving a frame within two attempts at extremely low SNR, by up to 107.9%, resulting in reduced excessive delay. The method to demodulate the proposed symbols lowers power consumption by tens to hundreds of milliwatts, depending on the device. Our proposal significantly helps to achieve high reliability and low power consumption of COTS devices in AAC.

Using Approximate Computing and Selective Hardening for the Reduction of Overheads in the Design of Radiation-Induced Fault-Tolerant Systems

Fault mitigation techniques based on pure software, known as software-implemented hardware fault tolerance (SIHFT), are very attractive for use in COTS (commercial off-the-shelf) microprocessors because they do not require physical modification of the system. However, these techniques cause software overheads that may affect the efficiency and costs of the overall system. This paper presents a design method of radiation-induced fault-tolerant microprocessor-based systems with lower execution time overheads. For this purpose, approximate computing and selective fault mitigation software-based techniques are used; thus it can be used in COTS devices. The proposal is validated through a case study for the TI MSP430 microcontroller. Results show that the designer can choose among a wide spectrum of design configurations, exploring different trade-offs between reliability, performance, and accuracy of results.

Low complexity OFDM VLC system enabled by spatial summing modulation.

Commercial-off-the-shelf (COTS) devices enabled visible light communication (VLC) for Internet of things (IoT) applications has attracted extensive attentions from both academic and industrial communities, thanks to the pervasive deployments of light emitting diode (LED) lighting infrastructure. However, due to the limitation of frequency response and non-linearity of the commercial illuminating LED light consisting of multiple LED chips, the achievable data rate is far less than that provided by the experimental VLC system with a single LED with specialized devices, e.g., lens. To this end, we propose a power-of-2 arrangement scheme for LED chips to generate spatial summing modulation with low control complexity, and demonstrate its availability in an orthogonal frequency division multiplexing (OFDM) VLC system purely built upon COTS devices. It significantly differs from a conventional OFDM VLC system relying on digital-to-analog converter (DAC) and analog signal chain, which is complex and confined by LED's non-linearity, thanks to we design a novel digital-to-light converter (DLC) which can output 256 light intensities linearly and be directly controlled by the discrete digital signals generated by the OFDM modulator. An experimental demonstration with employing the QAM-OFDM modulation scheme successfully confirms the effectiveness of the proposed spatial summing VLC system, which can achieve low BERs of below the forward error correct (FEC) threshold of 3.8×10-3 for both QAM8 and QAM16 running transmission frequency of 300 kHz under a communication distance of 0.8 m. It demonstrates the promising potential for delivering a data rate at hundred kbps level with this novel spatial summing based OFDM VLC system, which is sufficient for many IoT applications.

All-fiber self-compensating polarization encoder for quantum key distribution.

Quantum key distribution (QKD) allows distant parties to exchange cryptographic keys with unconditional security by encoding information on the degrees of freedom of photons. Polarization encoding has been extensively used for QKD along free-space, optical fiber, and satellite links. However, the polarization encoders used in such implementations are unstable, expensive, and complex and can even exhibit side channels that undermine the security of the protocol. Here we propose a self-compensating polarization encoder based on a lithium niobate phase modulator inside a Sagnac interferometer and implement it using only commercial off-the-shelf (COTS) components. Our polarization encoder combines a simple design and high stability reaching an intrinsic quantum bit error rate as low as 0.2%. Since realization is possible from the 800 to the 1550nm band using COTS devices, our polarization modulator is a promising solution for free-space, fiber, and satellite-based QKD.

Use of Commercial Off-The-Shelf Devices for the Detection of Manual Gestures in Surgery: Systematic Literature Review.

BackgroundThe increasingly pervasive presence of technology in the operating room raises the need to study the interaction between the surgeon and computer system. A new generation of tools known as commercial off-the-shelf (COTS) devices enabling touchless gesture–based human-computer interaction is currently being explored as a solution in surgical environments.ObjectiveThe aim of this systematic literature review was to provide an account of the state of the art of COTS devices in the detection of manual gestures in surgery and to identify their use as a simulation tool for motor skills teaching in minimally invasive surgery (MIS).MethodsFor this systematic literature review, a search was conducted in PubMed, Excerpta Medica dataBASE, ScienceDirect, Espacenet, OpenGrey, and the Institute of Electrical and Electronics Engineers databases. Articles published between January 2000 and December 2017 on the use of COTS devices for gesture detection in surgical environments and in simulation for surgical skills learning in MIS were evaluated and selected.ResultsA total of 3180 studies were identified, 86 of which met the search selection criteria. Microsoft Kinect (Microsoft Corp) and the Leap Motion Controller (Leap Motion Inc) were the most widely used COTS devices. The most common intervention was image manipulation in surgical and interventional radiology environments, followed by interaction with virtual reality environments for educational or interventional purposes. The possibility of using this technology to develop portable low-cost simulators for skills learning in MIS was also examined. As most of the articles identified in this systematic review were proof-of-concept or prototype user testing and feasibility testing studies, we concluded that the field was still in the exploratory phase in areas requiring touchless manipulation within environments and settings that must adhere to asepsis and antisepsis protocols, such as angiography suites and operating rooms.ConclusionsCOTS devices applied to hand and instrument gesture–based interfaces in the field of simulation for skills learning and training in MIS could open up a promising field to achieve ubiquitous training and presurgical warm up.

CeilingTalk: Lightweight Indoor Broadcast Through LED-Camera Communication

Although Visible Light Communication (VLC) is gaining increasing attention in research, developing a practical VLC system to harness its immediate benefits using Commercial Off-The-Shelf (COTS) devices is still an open issue. To this end, we develop and deploy CeilingTalk as a lightweight wireless broadcast system using COTS LED luminaries as transmitters and smartphone cameras as receivers so that it can be fully hosted in a smartphone and is feasible for all possible indoor environments. CeilingTalk innovates in both encoding and decoding to achieve an adequate throughput for realistic applications. On one hand, it employs Raptor coding to allow multiple LED luminaries to transmit collaboratively so as to benefit both throughput and reliability. On the other hand, it involves a lightweight decoding scheme to handle the asynchrony (both spatial and temporal) in transmissions. Moreover, we analyze the impact of various parameters on the performance of CeilingTalk, in order to derive a model for such VLC systems enabled by COTS devices and hence provide general guidance for future VLC deployments in larger scales. Finally, we conduct extensive field experiments to validate the effectiveness of our LED-camera VLC model, as well as to demonstrate the promising performance of CeilingTalk: up to 1.0 kb/s at a distance of 5 m.

AULOS: Finmeccanica family of passive sensors

The name comes from an Ancient Greek wind instrument because AULOS is a passive family system developed by SELEX Sistemi Integrati (now Finmeccanica) that exploits electromagnetic energy already present in the environment such as FM frequency radio and DVB-T (digital video broadcast - terrestrial) emissions, and is completely environmentally friendly. The new green system is the result of many years of R&D, some undertaken in concert with the Terrestrial Armaments Department [1], [2], [3], [4]. It is a technologically advanced family of sensors developed entirely on the basis of a soft radar approach, involving signal sampling directly at carrier frequency using COTS (commercial off the shelf) devices for signal reception and digital processing. The resulting biband family offers great flexibility for potential use in a variety of operating conditions, along with enhanced target monitoring distance and position estimate performance.

Development and interval testing of a naturalistic driving methodology to evaluate driving behavior in clinical research.

Background: The number of older adults in the United States will double by 2056. Additionally, the number of licensed drivers will increase along with extended driving-life expectancy. Motor vehicle crashes are a leading cause of injury and death in older adults. Alzheimer's disease (AD) also negatively impacts driving ability and increases crash risk. Conventional methods to evaluate driving ability are limited in predicting decline among older adults. Innovations in GPS hardware and software can monitor driving behavior in the actual environments people drive in. Commercial off-the-shelf (COTS) devices are affordable, easy to install and capture large volumes of data in real-time. However, adapting these methodologies for research can be challenging. This study sought to adapt a COTS device and determine an interval that produced accurate data on the actual route driven for use in future studies involving older adults with and without AD. Methods: Three subjects drove a single course in different vehicles at different intervals (30, 60 and 120 seconds), at different times of day, morning (9:00-11:59AM), afternoon (2:00-5:00PM) and night (7:00-10pm). The nine datasets were examined to determine the optimal collection interval. Results: Compared to the 120-second and 60-second intervals, the 30-second interval was optimal in capturing the actual route driven along with the lowest number of incorrect paths and affordability weighing considerations for data storage and curation. Discussion: Use of COTS devices offers minimal installation efforts, unobtrusive monitoring and discreet data extraction. However, these devices require strict protocols and controlled testing for adoption into research paradigms. After reliability and validity testing, these devices may provide valuable insight into daily driving behaviors and intraindividual change over time for populations of older adults with and without AD. Data can be aggregated over time to look at changes or adverse events and ascertain if decline in performance is occurring.

Development and interval testing of a naturalistic driving methodology to evaluate driving behavior in clinical research

Background: The number of older adults in the United States will double by 2056. Additionally, the number of licensed drivers will increase along with extended driving-life expectancy. Motor vehicle crashes are a leading cause of injury and death in older adults. Alzheimer's disease (AD) also negatively impacts driving ability and increases crash risk. Conventional methods to evaluate driving ability are limited in predicting decline among older adults. Innovations in GPS hardware and software can monitor driving behavior in the actual environments people drive in. Commercial off-the-shelf (COTS) devices are affordable, easy to install and capture large volumes of data in real-time. However, adapting these methodologies for research can be challenging. This study sought to adapt a COTS device and determine an interval that produced accurate data on the actual route driven for use in future studies involving older adults with and without AD. Methods: Three subjects drove a single course in different vehicles at different intervals (30, 60 and 120 seconds), at different times of day, morning (9:00-11:59AM), afternoon (2:00-5:00PM) and night (7:00-10pm). The nine datasets were examined to determine the optimal collection interval. Results: Compared to the 120-second and 60-second intervals, the 30-second interval was optimal in capturing the actual route driven along with the lowest number of incorrect paths and affordability weighing considerations for data storage and curation. Discussion: Use of COTS devices offers minimal installation efforts, unobtrusive monitoring and discreet data extraction. However, these devices require strict protocols and controlled testing for adoption into research paradigms. After reliability and validity testing, these devices may provide valuable insight into daily driving behaviors and intraindividual change over time for populations of older adults with and without AD. Data can be aggregated over time to look at changes or adverse events and ascertain if decline in performance is occurring.

Experimenting With Commodity 802.11 Hardware: Overview and Future Directions

The huge adoption of 802.11 technologies has triggered a vast amount of experimentally-driven research works. These works range from performance analysis to protocol enhancements, including the proposal of novel applications and services. Due to the affordability of the technology, this experimental research is typically based on commercial off-the-shelf (COTS) devices, and, given the rate at which 802.11 releases new standards (which are adopted into new, affordable devices), the field is likely to continue to produce results. In this paper, we review and categorise the most prevalent works carried out with 802.11 COTS devices over the past 15 years, to present a timely snapshot of the areas that have attracted the most attention so far, through a taxonomy that distinguishes between performance studies, enhancements, services, and methodology. In this way, we provide a quick overview of the results achieved by the research community that enables prospective authors to identify potential areas of new research, some of which are discussed after the presentation of the survey.