Cold Filter Plugging Point Values Research Articles

Physicochemical Characterization and Butanol Impact on Canola and Waste Cooking Oil Biodiesels: A Comparative Analysis with Binary Biodiesel Blends

In this study, the physicochemical properties of canola and waste cooking oil biodiesels, as well as various binary biodiesel blends, were investigated according to TS EN 14214 and ASTM D 6751 standards. Critical parameters such as density, kinematic viscosity, cold filter plugging point (CFPP), calorific value, flash point, copper strip corrosion, water content, and ester yield were evaluated. The findings highlighted the notable density of C100 and W100 biodiesels, with the addition of butanol reducing density. While viscosity values adhered to standards, the addition of butanol was observed to decrease viscosity. CFPP values indicated compliance with standards only for C100 and C75W25. Flash points of C100 and W100 biodiesels met standards, but the addition of butanol to binary biodiesel blends lowered flash points. Copper strip corrosion values were determined to comply with standards for all fuels. Calorific values demonstrated the prominence of C100 and W100 biodiesels, with the addition of butanol observed to decrease calorific values in binary biodiesels. While water content favored canola biodiesel over waste cooking oil biodiesel, the addition of butanol to binary biodiesels increased water content. Regarding ester yield, C100 biodiesel exhibited the highest yield, and the addition of butanol to binary biodiesels increased ester yield. In conclusion, this study thoroughly analyzed the physicochemical properties of biodiesel and blend fuels, revealing the impact of butanol addition on these properties.

The Influence of the Reaction Parameters on the Synthesis of Fatty Acid Octyl Esters and Investigation of Applications Properties of Its Blends with Mineral Diesel

The first aim of this paper is to study the influence of four parameters of the transesterification reaction—reaction temperature (40–80 °C), time (1–3 h), the molar ratio of 1-octanol to sunflower oil (4:1–10:1) and mass fraction of the catalyst (1–3 wt%)—on the conversion of oil to biodiesel (octyl esters of fatty acids), with potassium hydroxide as a catalyst. The highest conversion, of 99.2%, was obtained at 60 °C, a molar ratio of 1-octanol to sunflower oil of 10:1, and with 2 wt% of the catalyst after an hour. The optimal conditions determined with response surface methodology (RSM) when aiming for the lowest possible parameter values and a conversion of 95% or higher were a temperature of 40 °C, time of 1 h, 1-octanol to oil molar ratio at 8.11:1 and mass fraction of catalyst of 2.01%. Furthermore, post-synthesis and purification (>99%), the application properties of pure fatty acid octyl esters (FAOCE) and their blends with mineral diesel and 1-octanol were evaluated. Standardized tests were conducted to measure the fuel’s density, viscosity, cold filter plugging point (CFPP), and lubricity. The addition of FAOCE in mineral diesel increases its density, viscosity, and lubricity. When added up to 20 vol%, FAOCE did not have an influence on the blend’s CFPP value. Still, all the blend property values fell within the limits required by standard EN 590.

Effects of ethyl proxitol (1-ethoxy-2-propanol) additive on combustion and emission characteristics of biodiesel blends

The cold filter plugging point (CFPP) value of biodiesel fuel blends need to be improved because of it has been reported that utilizing high concentrations of biodiesel blends in cold climates can cause major issues. Therefore, the main objective of the study is to improve CFPP value of biodiesel blends using ethyl proxitol additive. It is also to examine combustion and emission of the blends behavior. Biodiesel blends were prepared as; 5% ethyl proxitol-10% biodiesel-85% ultra-low sulfur diesel (ULSD) named as E5B10 and 5% ethyl proxitol-20% biodiesel-75% ULSD named as E5B20 fuel. These fuel blends were compared with ULSD fuel in a compression ignition engine at a constant engine speed of 1500 rev/min and four different loads (idle, 1, 2, and 3 bar BMEP) of eddy current dynamometer. The addition of ethyl proxitol led to a decrease in in-cylinder pressure and temperature due to an about 1˚ later SOC and 2˚ earlier EOC compared to ULSD. The pressure rise rate was slightly higher compared to ULSD at both low and high loads, with a difference of about 1 bar per degree. As a result, these blends with improved CFPP value can be used in cold climates.

Formate Esters Containing Biodiesel - Diesel Mixed Fuels

The blends of varying proportions of biodiesel (FAME) containing formate esters of glycerol and 93.0 wt.% fatty acid methyl esters, obtained in an interesterification reaction with methyl formate without further purification, and winter diesel fuel, were prepared, analyzed and compared with winter diesel fuel. The obtained results showed that blends comprising up to 20 vol.% of FAME fulfill the requirements of the standard LVS EN 590 concerning such characteristics as cold flow properties, viscosity, density, and carbon residue. The increase of FAME content worsens the cold flow properties; however, the mixed fuel with 20 vol.% or lower FAME content, according to the cloud point and cold filter plugging point values, remains in the same severe climate "Class 0" group as winter fuel. The carbon residue of mixed fuels raises with increasing FAME content, but stay low and do not exceed the limits of standard for mixtures with FAME percentage up to 20 vol.%. The comparison of mixed fuels containing 20 vol.% of FAME and the same amount of neat biodiesel (99.6 wt.% of fatty acid methyl esters) shows that the difference is negligible. The obtained results have indicated a good potential of FAME obtained in the interesterification reaction with methyl formate without further purification as a diesel fuel additive for up to 20 vol.%.

Poly(3-pentadecylphenyl acrylate) having a bottlebrush-like structure for high-performance middle distillate flow improver

Bottlebrush-like structured poly(3-pentadecylphenyl acrylate) (PPDPA) was prepared and found to be an effective middle distillate flow improver (MDFI) for enhancing the cold properties of diesel, such as the cloud point (CP), cold filter plugging point (CFPP), and pour point (PP). For example, when 250 ppm of PPDPA was added to base diesel, the CP, CFPP, and PP values of the diesel decreased from −3, −9, and −15 °C to −6, −13, and −24 °C, respectively. Interestingly, when another bottlebrush polymer, poly(n-pentadecyl acrylate) (PPDA), with a very similar chemical structure was prepared and added to the diesel in a concentration of 250 ppm, the CFPP increased to −8 °C. Differential scanning calorimetry and polarized optical microscopy results indicated that the additional phenyl group on the side chain restricted the crystallization of the pentadecyl side group. PPDPA, with the 3-pentadecylphenyl side group, hindered the wax crystallization in the diesel, while PPDA, with the 3-pentadecyl side group without the phenyl structure, facilitated the wax crystallization.

Evaluation of the oxidative stability and cold filter plugging point of soybean methyl biodiesel/bovine tallow methyl biodiesel blends

The objective of the present work was to study the oxidative stability (OS) estimated from the induction period (IP) and the cold filter plugging point (CFPP) of blends made with different proportions of soybean methyl biodiesel (BOS) and bovine tallow methyl biodiesel (BSB). BOS is poorly resistant to oxidation because its composition is predominantly unsaturated esters, but it has a satisfactory cold filter plugging point. The BSB is composed of saturated esters and of the lower carbon chain and thus has good oxidation stability values, but has poor CFPP values. Thus, BOS / BSB mixtures in different proportions were made to evaluate the ideal amount of the mixture in which it was possible to obtain IP and CFPP properties in satisfactory values by the legislation. The mixtures started at 10% BSB and 90% BOS and was increased 5% up to the 50% percentage of each biodiesel in each blend. Samples with 45% and 50% BSB had oxidative stability above the minimum required by law, and all blends had the CFPP value within the legal values.

Biodiesel production through algal cultivation in urban wastewater using algal floway

The aim of this work was to study algal floway (AFW) to treat urban wastewater and to evaluate biomass productivity, lipid contents and biodiesel production. The results indicated the seasonal average algae productivity of 34.83 g dry weight m2 d−1 with a nutrient removal rate of 2.52 g m2 d−1N and 1.25 g m2 d−1P while the lipid content ranged between 14 and 22% of dry cell weight with the highest lipid productivity of 9.29 g m−2 d−1 during summer. Biodiesel quality was superior during summer with high centane number and cold filter plugging point values. High eicosapentaenoic acid content was found during winter growth cycles. AFW algae community was dominated by pennate diatoms during all growing seasons. This study is one of its kinds in Indian wastewaters and it provides fundamental information for further optimization and use of AFW to treat domestic wastewater and to produce algae biofuel feedstock.

Multiresponse optimisation on biodiesel obtained through a ternary mixture of vegetable oil and animal fat: Simplex-centroid mixture design application

The quality of biodiesel is a determining factor in its commercialisation, and parameters such as the Cold Filter Plugging Point (CFPP) and Induction Period (IP) determine its operability in engines on cold days and storage time, respectively. These factors are important in characterisation of the final product. A B100 biodiesel formulation was developed using a multiresponse optimisation, for which the CFPP and cost were minimised, and the IP and yield were maximised. The experiments were carried out according to a simplex-centroid mixture design using soybean oil, beef tallow, and poultry fat. The optimum formulation consisted of 50% soybean oil, 20% beef tallow, and 30% poultry fat and had CFPP values of 1.92°C, raw material costs of US$ 903.87ton−1, an IP of 8.28h, and a yield of 95.68%. Validation was performed in triplicate and the t-test indicated that there were no difference between the estimated and experimental values for none of the dependent variables, thus indicating efficiency of the joint optimisation in the biodiesel production process that met the criteria for CFPP and IP, as well as high yield and low cost.

Improvement of Low Temperature Properties of Jatropha-Corn Biodiesel Blend with the Addition of Acrylic Co-Polymer

Inevitable low temperature properties is one of the major problems in commercialization of pure biodiesel. Increasing the usage of edible oil in biodiesel production creates the fuel versus food controversy. This paper involves the study of cold flow properties of edible and non-edible oils biodiesel. Corn biodiesel and jatropha biodiesel are blended respectively. The blend ratio of corn methyl ester and jatropha methyl ester CME: JME (20:80) has the oxidative stability of 6.42 hours and cold filter plugging point value of-2 oC. An additive of acrylic co-polymer as the cold flow improver (CFI) reduced the CFPP value from-2 oC to-6 oC which results in better low temperature properties of corn-jatropha biodiesel blend.

Effect of agronomic inputs and crop rotation on biodiesel quality and fatty acid profiles of direct-seeded canola

Harker, K. N., O'Donovan, J. T., Blackshaw, R. E., Hall, L. M., Willenborg, C. J., Kutcher, H. R., Gan, Y., Lafond, G. P., May, W. E., Grant, C. A., Barthet, V., McDonald, T., Wispinski, D. and Hartman, M. 2013. Effect of agronomic inputs and crop rotation on biodiesel quality and fatty acid profiles of direct-seeded canola. Can. J. Plant Sci. 93: 577–588. A field study was conducted at eight sites in western Canada to determine the influence of agronomic inputs on fatty acid profiles and biodiesel quality of canola. Protein and chlorophyll concentration and fatty acid profiles were determined from seed samples at all sites. Oil was extracted from canola seed samples from three sites, converted to biodiesel, and subjected to standard protocols. Protein concentration increased at higher than recommended rates of nitrogen (N) and the higher canola seeding rate (150 seeds m−2) reduced chlorophyll levels in canola oil. All biodiesel samples fell below new oxidation stability tolerance levels (minimum 8 h). However, given the routine addition of commercial antioxidant additives, all biodiesel samples from this study were suitable for blending in middle distillate fuels. Cloud point values were lowest at normal N (1×) rates. Normal N rates increased stearic acid content, whereas high N rates (1.5×) increased gadoleic acid content. Low seeding rates (75 seeds m−2) increased palmitic acid content. The combination of normal N (1×) with a high seed rate (150 seeds m−2) increased oleic acid content. Conversely, the combination of high N (1.5×) with a low seed rate (75 seeds m−2) increased linolenic acid content. Gadoleic acid content increased in the continuous canola rotation versus the canola–wheat–canola rotation; similar trends were observed with palmitic, linoleic, and linolenic acid. Oleic acid tended to be higher in canola rotated with wheat. Cold filter plugging point (CFPP) was predicted based on saturated fatty acid content. Usually, a high seeding rate (150 seeds m−2) combined with a normal N rate (1×) led to the most favourable (lowest) CFPP values. Low CFPP values were also associated with canola rotated with wheat compared with continuous canola production. Seeding rate, N, and crop rotation influenced protein and chlorophyll concentration, fatty acid profiles, cloud point, and CFPP.

Biodiesels from beef tallow/soybean oil/babassu oil blends

Cloud point (CP), cold filter plugging point (CFPP), and pour point (PP) of biodiesel samples obtained from blends containing different amounts of beef tallow, babassu oil, and soybean oil were investigated by the corresponding conventional techniques and by temperature modulated differential scanning calorimetry (TMDSC). The CP and CFPP values correlate well with the crystallization temperature (Tonset) obtained from the TMDSC curves, being the highest for the biodiesel sample containing the highest amount of methyl stearate. A correspondence between PP and the peak temperature was also noticed, pointing out that pouring ceases after the crystallization of the heavier fatty acid ester. Among the samples of biodiesel, Bio-3 (highest amount of babassu oil) and Bio-4 (highest amount of soybean oil) showed better cold-flow properties, or in other words, lower values of CP, CFPP, and PP. Independently of the composition, the cold-flow properties of all biodiesel samples meet the requirements from the Brazilian National Agency of Petroleum, Natural Gas, and Biofuels (ANP).

Preparation of Biofuel Using Acetylatation of Jojoba Fatty Alcohols and Assessment as a Blend Component in Ultralow Sulfur Diesel Fuel

The majority of biodiesel fuels are produced from vegetable oils or animal fats by transesterification of oil with alcohol in the presence of a catalyst. In this study, a new class of biofuel is explored by acetylation of fatty alcohols from Jojoba oil. Jojobyl methyl acetate (JMA) was produced using direct acetylation of purified jojobyl alcohol obtained during preparation of Jojobyl methyl esters (JME). Important fuel properties of JMA, such as kinematic viscosity, cloud point (CP), pour point (PP), cold filter plugging point (CFPP), acid value, oxidative stability, gross heat of combustion, and lubricity were evaluated using standard methods. A comparison was made with previously reported JME and relevant biodiesel fuel standards, such as ASTM D6751 and EN 14214. The CP, CFPP, and PP values of JMA were 2, −10, and −16 °C, respectively. These results were comparable to JME with the exception of a higher CP in the case of JMA. The kinematic viscosity (40 °C) of JMA was 7.64 mm2/s, which was higher than t...

Transesterified Chinese Spicehush (Lindera communis) seed oil as a biodiesel fuel

Studies were carried out on the transesterification of the Chinese Spicehush (Lindera communis) seed (LCS) oil with methanol for the production of biodiesel. The methyl esters of LCS oil were compared with soybean esters to determine biodiesel fuel performance and properties. The fatty acids content in the seed kernel oil (LKO) and coat oil (LCO) were quantified by gas chromatography and mass spectrometry method (GC-MS). LKO contains 95.1% saturated acids (capric, lauric, myristic and palmitic) and 2.3% unsaturated acids (oleic). LCO contains 24.6% saturated acids (palmitic and stearic) and 73.6% unsaturated acids (oleic, linoleic and palmitoleic). The kinematic viscosity, cold filter plugging point, cloud point, flash point and cetane index were determined. The methyl esters of LKO had a higher kinematic viscosity and a lower cold filter plugging point value, so it has better performance in cold weather. The biodiesel of LCS oil has fuel properties within the limits prescribed by American (ASTM D 6751-02) standards, except for a slightly lower flash point of LKO biodiesel than that prescribed by these standards (130°C). Thus, LKO and LCO biodiesel have great potential to be used on a large scale as fuel for diesel engines.

Cold flow properties of fuel mixtures containing biodiesel derived from animal fatty waste

The aims of the present study were to evaluate the cold temperature behavior of methyl esters of vegetable and animal origin and of their mixtures with fossil diesel fuel, as well as to investigate the effectiveness of different depressants. Various blends of rapeseed oil methyl esters, linseed oil methyl esters, pork lard methyl esters and fossil diesel fuel were prepared, and both cloud point and cold filter plugging point (CFPP) were analyzed. It was found that mixtures with CFPP values of –5 °C and lower may contain up to 25% of pork lard methyl esters; whereas the ratio of summer fossil diesel fuel and rapeseed oil methyl esters may vary over a wide range, i.e. such mixtures can be used in a diesel engine in the summer. In the transitory periods it is possible to use up to 20% animal and vegetable ester blends (3 : 7) with winter fossil diesel, whereas only up to 5% of esters can be added to the fuel used in winter. In order to improve the cold properties of rapeseed oil, pork lard and linseed oil methyl ester mixtures, various additives were tested. Depressant Viscoplex 10–35 with an optimal dose of 5000 mg/kg was found to be the most effective.

Winterisation of waste cooking oil methyl ester to improve cold temperature fuel properties

Waste cooking oil methyl ester (WCOME) was winterised at 1, 0, −1 and −2°C following a 4×2 factorial design with one replication per cell. The process was carried out by filtration and both the filtrate (solid phase) and the liquid phase were analysed by gas chromatography (GC), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Cold filter plugging point (CFPP) and calorific values were measured. Temperatures of 0 and −1°C in conjunction with the quickest cooling rate (0.1°C min −1) and 15–24 h of cooling gave the most successful results in terms of fuel properties. Improvements in the low temperature properties of the winterised fuel were reflected by a reduction of saturated fatty acid methyl esters (SFAME) in the composition by 1.5–6%, by a decrease in the CFPP values by 2–4°C and by a shift of the DSC high temperature melting peak (approx. 5°C) towards lower temperatures in comparison to the original fuel. Calorific values of the winterised WCOME did not significantly change and boiling temperatures increased (approx. 26%) in comparison to the non-winterised WCOME.