Conductivity Coefficient Research Articles

Colossal Near-Field Radiative Heat Transfer Mediated by Coupled Polaritons with an Ultrahigh Dynamic Range.

Near-field radiative heat transfer (NFRHT) can exceed the blackbody limit by several orders of magnitude owing to the tunneling evanescent waves. Exploiting this near-field enhancement holds significant potential for emerging technologies. It has been suggested that coupled polaritons can give rise to orders of magnitude enhancement of NFRHT. However, a thorough experimental verification of this phenomenon is still missing. Here this work experimentally shows that NFRHT mediated by coupled polaritons in millimeter-size graphene/SiC/SiO2 composite devices in planar plate configuration can realize about 302.8 ± 35.2-fold enhancement with respect to the blackbody limit at a gap distance of 87 ± 0.8nm. The radiative thermal conductance and effective gap heat transfer coefficient can reach unprecedented values of 0.136 WK-1 and 5440 Wm-2K-1. Additionally, a scattering-type scanning near-field optical measurement, in conjunction with full-wave numerical simulations, provides further evidence for the coupled polaritonic characteristics of the devices. Notably, this work experimentally demonstrates dynamic regulation of NFRHT can be achieved by modulating the bias voltage, leading to an ultrahigh dynamic range of ≈4.115. This work ambiguously elucidates the important role of coupled polaritons in NFRHT, paving the way for the manipulation of nanoscale heat transport, energy conversion, and thermal computing via the strong coupling effect.

Nanostructured inclusions enhancing the thermoelectric performance of Higher Manganese Silicide by modulating the transport properties

Higher Manganese Silicides (HMS) are the best p-type materials beneficial for intermediate-temperature range thermoelectric device applications due to their high thermal stability and inexpensive constituent elements. Although the cost-effective HMS materials possess high thermal stability, they are concerned with high thermal conductivity values. The nanocomposite approach was promised to lower the thermal transport properties without affecting the electrical transport properties, which is experimented in the present work. The higher manganese silicide with varying weight percentages of nano-structured Si0.8Ge0.2B0.02 inclusions was experimented to decrease the thermal conductivity and to enhance the electrical properties. The lowest thermal conductivity value of ≃ 2.24 W/mK was reported with 2 wt% Si0.8Ge0.2B0.02 addition in HMS material. Also, the HMS-2 wt. % Si0.8Ge0.2B0.02 improved the transport properties, electrical conductivity and Seebeck coefficient values of ≃ 4 × 104 S/m and ≃ 220 μV/K respectively. Furthermore, various mathematical models were proposed here to simulate the composite approach results, which were then correlated with experimental results.

Theoretical study of optoelectronic, elastic and mechanical properties of gallium modified barium titanate (Ba1-xGaxTiO3) perovskite ceramics by DFT

In this report, we study the gallium modified Barium titanate (Ga-BTO) Ba1-xGaxTiO3 with (x = 50 %) perovskite ceramics, which have not been synthesized experimentally to date. The density functional theory-based full potential linear augmented plane wave has been employed to determine the optoelectronic, elastic, and mechanical properties of pure and modified BaTiO3. Completely relaxed 2 × 2× 2 of primitive five atoms’ cells has been used for calculations. A large cut-off energy of 120 Ry has been used to eliminate the basics of plane wave-indicating wave functions. The influence of substitution of Ga on electronic structure and optical parameters such as reflectivity, refractivity, dielectric function, optical conductivity, extinction, and absorption coefficients are analyzed and elucidated with TDOS and PDOS. The Ga modified BTO manifests a forbidden energy gap of 1.84 eV. The static dielectric constant Ɛ1(o) has values of 8.8 and 100 for pure and modified compounds respectively. Ga dopant improved the polarizing power of BTO and for the doped BTO imaginary part, Ɛ2(ω)showed a prominent peak located at 3.9 eV. The optical properties show that perovskite compound substituted with Ga is a good absorber in the ultraviolet region and the modified material has a small value of reflectivity and static refractive index 12.2. The general profiles of optical spectra of modified BaTiO3 display highly desirable features like the prominent peaks of optical conductivity obtained at 4.2 and 5.8 eV for modified BTO that make it a promising candidate for optoelectronic and spintronics. Ga-modified BTO has higher ductility, modulus (169.96 GPa), and anisotropy (2.949) than pure BTO found by analyzing their elastic and mechanical properties.

Simulation of Frost-Heave Failure of Air-Entrained Concrete Based on Thermal-Hydraulic-Mechanical Coupling Model.

The internal pore structural characteristics and microbubble distribution features of concrete have a significant impact on its frost resistance, but their size is relatively small compared to aggregates, making them difficult to visually represent in the mesoscopic numerical model of concrete. Therefore, based on the ice-crystal phase transition mechanism of pore water and the theory of fine-scale inclusions, this paper establishes an estimation model for effective thermal conductivity and permeability coefficients that can reflect the distribution characteristics of the internal pore size and the content of microbubbles in porous media and explores the evolution mechanism of effective thermal conductivity and permeability coefficients during the freezing process. The segmented Gaussian integration method is adopted for the calculation of integrals involving pore size distribution curves. In addition, based on the concept that the fracture phase represents continuous damage, a switching model for the permeability coefficient is proposed to address the fundamental impact of frost cracking on permeability. Finally, the proposed estimation models for thermal conductivity and permeability are applied to the cement mortar and the interface transition zone (ITZ), and a thermal-hydraulic-mechanical coupling finite element model of concrete specimens at the mesoscale based on the fracture phase-field method is established. After that, the frost-cracking mechanism in ordinary concrete samples during the freezing process is explored, as well as the mechanism of microbubbles in relieving pore pressure and the adverse effect of accelerated cooling on frost cracking. The results show that the cracks first occurred near the aggregate on the concrete sample surface and then extended inward along the interface transition zone, which is consistent with the frost-cracking scenario of concrete structures in cold regions.

Effect of nanosized carbon nanotubes, Titanium Nitride and cubic Boron Nitride powders on mechanical and thermal properties of SLA 3D printed resin composites

AbstractThis study explores the development of nanocomposites by incorporating multi‐walled carbon nanotubes (MWCNT), titanium nitride (TiN), and cubic boron nitride (c‐BN) nano powders into photo‐polymer epoxy resins for use in Stereolithography (SLA) additive manufacturing. Mechanical and thermal properties were systematically investigated to assess their performance. Initially, MWCNT, TiN, and c‐BN nano powders were homogeneously mixed with the resin to ensure uniformity. The resulting mixtures were then processed using SLA technology to evaluate production quality and material performance. The study revealed significant improvements in mechanical and thermal properties compared to pure resin, aligning with previous research outcomes. Specifically, the incorporation of MWCNT led to a notable enhancement in thermal conductivity, showing an increase of 24.21% as the thermal conductivity coefficient increased from 0.19 to 2.36 W/m·k. On the other hand, c‐BN significantly boosted mechanical strength, resulting in a substantial 20.45% increase as the shore D hardness went from 88.53 to 106.64. These findings highlight the promising potential of nanocomposites across various industries including electronics, aerospace, automotive, construction, medical devices, and manufacturing.Highlights Developed nanocomposites with MWCNT, TiN, and c‐BN in SLA resin. c‐BN increased hardness by 20.45%, proving its effectiveness in composites. MWCNT enhanced thermal conductivity by 24.21%, boosting material performance. Pioneering use of TiN and c‐BN in SLA, addressing gaps in existing research. Applications span electronics, aerospace, automotive and medical devices.

Effects of physical property dynamic change on heat transfer characteristics of coal seam during in-situ pyrolysis of tar-rich coal

Tar-rich coal has the features of high tar yield and great potential for oil production. The underground in-situ pyrolysis technology is an effective way to accomplish the green and efficient utilization of tar-rich coal resources. The pore structures of coal seam have great change in the actual in-situ pyrolysis process. Hence, the physical properties of coal seam also vary with pyrolysis temperature, which affects the heat transfer performance of coal seam. However, previous studies on heat transfer characteristics of coal seam have been seldom paid attention to the physical property dynamic change during the in-situ pyrolysis, which possibly causes deviation between the simulated heat transfer characteristics and the actual performance. It is still unclear whether the deviation is acceptable in practical engineering practice at present. In this article, a modification scheme for the physical property dynamic change of coal seam was proposed. The effects of physical property dynamic change on heat transfer characteristics of coal seam during in-situ pyrolysis of tar-rich coal were analyzed using numerical simulation approach. In addition to single factor correction, the effects of three-factor coupling modification on heat transfer performance of coal seam were also systematically investigated. The simulation results indicated that both the average temperature and the effective heating area of the coal seam increased after the specific heat capacity was corrected individually. Whereas, the heat transfer of coal seam was weakened after the endothermic effect of pyrolysis and the thermal conductivity coefficient were modified, respectively. When the three factors were coupled for correction in the single well and single fracture mode, the correction factor that played a leading role was the thermal conductivity coefficient, accounting for 90%. However, an increase in the number of cracks enhanced the heat transfer, resulting in the specific heat capacity was dominant among the three correction factors. The present study can offer theoretical guidance and technical support for realizing large-scale in-situ pyrolysis of tar-rich coal.

Review of recent research on thermal management of diamond/metal composites

Diamond/metal composites have attracted much attention due to their excellent thermal conductivity (TC) and low coefficient of thermal expansion (CTE). This paper introduces two significant interface modification means which can improve interface bonding between diamond and metal. And the key factors affecting the TC of composite are analysed, making the thermal management of diamond/metal composites more efficient.

CRYOGELS TO INCREASE THE SERVICE LIFE OF WINTER ROADS

The work proposes a method for forming a composite cryotron material based on an aqueous solution of polyvinyl alcohol for application to the surface of a snow-ice sheet. Freezing an aqueous solution of polyvinyl alcohol at a negative temperature and subsequent thawing at a temperature above zero leads to the formation of elastic cryogels. The introduction of boric acid into a polymer solution leads to chemical cross-linking of kinetically individual macromolecules of polyvinyl alcohol into spatial networks that have elastic properties. The practical interest in using materials based on cryogels is due to environmental safety, high physicochemical and thermophysical properties, a simple method for their preparation and low cost. When studying the kinetics of gelation of multicomponent systems, it was observed that the formation of a gel at a temperature of 5 °C occurs after approximately 13 hours. It has been established that with increasing temperature control time of the gel at a temperature of 5 °C, the elastic modulus of samples obtained as a result of a chemical reaction increases by 2 times in approximately 120 h. It has been shown that after cryostructuring of multicomponent solutions, the elastic modulus increases 9 times. The presence of sand in a structured system significantly increases the elastic properties of the gel and cryogel. It should be noted that the thermal conductivity coefficient of cryogels is almost 2 times less than that of water, and the melting point is more than 60 °C. The results of practical experiments show that coating a snow-ice surface with cryogel reduces the rate of its melting and, therefore, compositions based on cryogels can be used to extend the life of safe operation of winter roads. For citation: Fufaeva M.S., Altunina L.K. Cryogels to increase the service life of winter roads. ChemChemTech [Izv. Vyssh. Uchebn. Zaved. Khim. Khim. Tekhnol.]. 2024. V. 67. N 8. P. 29-35. DOI: 10.6060/ivkkt.20246708.13t.

Influence of varying matrix/fiber concentration on mechanical properties of bi-directional carbon fiber reinforced polymer composite

The polymer composites comprising bi-directional carbon fabric incorporated in the epoxy matrix have been developed for various advanced applications in the field of automobile and aerospace sectors. The distinct advantages of using epoxy material with hardener are good adhesion, high tensile, compression and bending strengths, good corrosion, and heat resistance properties. Using carbon fiber enhances the stiffness, reduces the weight, and improves the chemical resistance apart from possessing high thermal conductivity and low coefficient of thermal expansion. Considering all the above aspects, the present work proposes to investigate the mechanical properties of carbon-reinforced epoxy composites with fiber matrix ratios of 40:60, 50:50, and 60:40 by wt% as these particular combinations have been limitedly addressed so far. The well-known hand lay-up technique has produced the laminates and the test samples prepared from the laminate are subjected to tensile, flexural, hardness, and impact strength properties. Based on the experimental work of the composites made in the laboratory, the fiber matrix ratio of 60:40 has revealed the best attributes in terms of higher mechanical strengths compared to the composites with fiber matrix ratio of 40:60 and 50:50 and the data obtained have been substantiated using scanning electron microscope analysis.

Thermal shock behavior of Al–Y2O3 doped aluminum nitride ceramics

Thermal shock resistance and mechanical reliability of aluminum nitride (AlN) ceramic substrates are essential in electronic device modules. In this study, the thermal shock behavior of AlN doped with aluminum - yttrium oxide (Al - Y2O3) was explored. The results indicate that adding Al to AlN ceramics increases its flexural strength, thermal conductivity, and thermal expansion coefficient. The microcracks caused by thermal mismatch between the AlN matrix and the secondary phases relieved internal stress, thereby improving thermal shock resistance of AlN ceramics. Furthermore, the addition of Al isolates and homogenizes the secondary phases, resulting in a more uniform microstructure and strengthened grain boundaries, which enhance the flexural strength, Weibull modulus, and thermal shock resistance. After introducing 0.5 wt% Al, the Weibull modulus of AlN ceramics increased by 73.37 %, and their critical thermal shock temperature difference exceeded 800 °C, with a maximum residual strength of 488.01 ± 48.26 MPa at 600 °C. Overall, an appropriate amount of Al improves the reliability and thermal shock resistance of AlN ceramics.

Inverse parameter and shape problem for an isotropic scatterer with two conductivity coefficients

Inverse parameter and shape problem for an isotropic scatterer with two conductivity coefficients

Investigation on the influence of waste-based fillers on the mechanical and thermal characteristics of rigid polyurethane foams

An investigation was conducted to analyze the impact of incorporating coal powder particles at different weight ratios (5, 10, 15, 25, and 35) on the mechanical properties and thermal conductivity coefficient of the polyurethane polymer. The thermal conductivity coefficient of the samples was calculated using Holmarc's Lee's Disc apparatus device. The mechanical properties like compressive, tensile, and bending strengths were measured using a universal machine. The results indicated that increasing the coal powder ratio leads to an improvement in the thermal insulation ability due to a decrease in the value of thermal conductivity. Also, the addition of these percentages led to a rise in the values of the mechanical qualities represented by the compressive strength, especially at the ratio of 25 wt. %, with a value equal to 2.79 MPa (MPa). The flexural resistance and tensile strength increase at a ratio of 35 wt. %, with values equal to 20.4 MPa and 2.86 MPa respectively. The results indicate that the addition of coal powder enhances the ability of thermal conductivity at the ratios (5 %, 10) wt. %, with values equal to 0.119 W/m ºC and 0.114 W/m ºC, respectively, by increasing the thermal conductivities of the samples. The aim of this study is, investigate the effect of filler used coal powder waste on the mechanical and thermal properties of PU. The filler materials show the advantages of recycling waste. Filler influences the morphology and strengthens the brittleness. Additionally, the technology of polyurethane materials conforms to the use of coal powder. The overall amount of energy used to produce PU composites is decreased when waste of filler is used to partially replace petrochemical components

Characterization of wood fiber insulation for the development of wood fiber-insulated panels (WIPs) for use in building envelope

Wood fiber insulation (WFI) was studied as an eco-friendly alternative for fossil-based building insulation, focusing on its use in new wood fiber-insulated panels (WIPs). Rigid WFI boards with densities of 110, 140, and 180 kg/m³, including a 140 kg/m³ variant without paraffin wax, were evaluated. Key properties investigated included porosity, water vapor transmission, liquid water adsorption, and thermal conductivity. The porosity ranged between 85 and 92%, primarily influenced by density. Water vapor permeability ranged from 65 to 90 ng·s-1m-1Pa-1, while liquid water absorption was between 2.5 and 20% by volume, influenced by both wax and density. The thermal conductivity coefficient ranged from 0.038 to 0.055 W/(m·K). Bond strength tests with WFI (140 kg/m³ with wax) laminated to various materials using structural adhesives showed tensile perpendicular-to-grain strengths of 10 to 16 kPa and shear strengths of 60 to 90 kPa, with failure only occurring within the WFI. It was concluded that WFI is a promising material for novel WIPs, offering competitive hygrothermal properties and compatibility with structural adhesives. However, its bio-based nature suggests variability and complexity, necessitating further rigorous testing in various climates and in more complex assemblies.

Interface strengthening for carbon fiber‐reinforced poly(ether‐ether‐ketone) laminated composites by introducing fluorene‐containing branched poly(aryl‐ether‐ketone)

AbstractFluorene‐containing branched poly(aryl‐ether‐ketone) (BFPAEK) with terminal hydroxyl groups is synthesized by random copolycondensation reaction; then, the CF@BFPAEK/PEEK laminated composite is prepared by the “powder impregnation‐high temperature compression molding” method with poly(ether‐ether‐ketone) (PEEK) as the matrix and BFPAEK‐modified carbon fiber (CF@BFPAEK) as the reinforcement. When the content of branched units in BFPAEK is 10% and the coating amount of BFPAEK on the carbon fiber (CF) surface is 3 wt%, the CF@BFPAEK/PEEK laminated composite has outstanding mechanical properties, with an interlaminar shear strength (ILSS) of 57.3 MPa and flexural strength of 589.4 MPa, which are 80.2% and 44.3% higher than those of the pure CF/PEEK laminated composite (31.8 and 408.4 MPa), respectively. After 288 h of hydrothermal aging and high/low‐temperature alternating aging, the corresponding retention rate of ILSS and flexural strength are respectively 87.9% and 84.7%, higher than those of pure CF/PEEK laminated composites (74.5% and 70.4%). The thermal conductivity coefficient and temperature for 5% weight loss of CF@BFPAEK/PEEK laminated composite are 1.85 W m−1 K−1 and 538.0°C, respectively.

Cation interception and permeability characteristics of bentonite barriers exposed to NaCl and NH4Cl solutions.

High concentrations of Na+ and NH4+ in landfill leachate lead to deterioration of bentonite barrier and pose a threat to the environment. This study focused on the pollution interception and permeability characteristics of the bentonite barrier exposed to NaCl and NH4Cl solutions. Based on previous findings, salt solution concentrations were established at 74.80, 37.40, 18.70, and 9.4 mmol/L. The bentonite contents in the mixture were set at 0, 5, 10, and 15%. The results indicate that the samples exhibit better interception of NH4+ compared to Na+. This difference arises from the cation exchange sequence, the size of the hydration radius, and the hydrogen bonding of the two cations. Additionally, the difference in hydration enthalpy between the two cations leads to variations in the swelling of bentonite, resulting in a higher hydraulic conductivity coefficient in NH4Cl solution. This study shows that although bentonite barriers have better interception for NH4+, they exhibit greater hydraulic conductivity in NH4Cl solution, increasing the risk of leachate carrying other contaminants.

Examining the Workability, Mechanical, and Thermal Characteristics of Eco-Friendly, Structural Self-Compacting Lightweight Concrete Enhanced with Fly Ash and Silica Fume.

This study compares the workability, mechanical, and thermal characteristics of structural self-compacting lightweight concrete (SCLWC) formulations using pumice aggregate (PA), expanded perlite aggregate (EPA), fly ash (FA), and silica fume (SF). FA and SF were used as partial substitutes for cement at a 10% ratio in various mixes, impacting different aspects: According to the obtained results, FA enhanced the workability but SF reduced it, while SF improved the compressive and splitting tensile strengths more than FA. EPA, used as a fine aggregate alongside PA, decreased the workability, compressive strength, and splitting tensile strength compared to the control mix (K0). The thermal properties were altered by FA and SF similarly, while EPA notably reduced the thermal conductivity coefficients. The thermal conductivity coefficients (TCCs) of the K0-K4 SCLWC mixtures ranged from 0.275 to 0.364 W/mK. K0 had a TCC of 0.364 W/mK. With 10% FA, K1 achieved 0.305 W/mK; K2 with 10% SF reached 0.325 W/mK. K3 and K4, using EPA instead of PA, showed significantly lower TCC values: 0.275 W/mK and 0.289 W/mK, respectively. FA and SF improved the thermal conductivity compared to K0, while EPA further reduced the TCC values in K3 and K4 compared to K1 and K2. The compressive strength (CS) values of the K0-K4 SCLWC mixtures at 7 and 28 days reveal notable trends. Using 10% FA in K1 decreased the CS at both 7 days (12.16 MPa) and 28 days (22.36 MPa), attributed to FA's gradual pozzolanic activity. Conversely, K2 with SF showed increased CS at 7 days (17.88 MPa) and 28 days (29.89 MPa) due to SF's rapid pozzolanic activity. Incorporating EPA into K3 and K4 reduced the CS values compared to PA, indicating EPA's lower strength contribution due to its porous structure.

PNIPAM-based ionic hydrogels for enhanced privacy smart windows and flexible sensor

The thermochromic materials are widely used in the smart window field because they can efficiently regulate solar radiation with temperature changes. Currently, most smart windows switch back and forth between opaque and transparent states to control solar radiation, which is very disadvantageous for the visibility of enclosed environments. Herein, in a binary solvent of ethylene glycol-water (EW), we are developing a series of thermoresponsive ion hydrogels suitable for smart windows by in-situ free radical polymerization of the thermoresponsive monomer N-isopropylacrylamide (NIPAM) and ionic monomers (amphiphilic, anionic, cationic). These smart windows exhibit excellent one-way transparency for privacy protection, allowing observation from a relatively dark private space to a public space outside the smart window during the day, while preventing a view from the relatively bright public space into the private space. Furthermore, these hydrogels demonstrate efficient blocking of ultraviolet / near-infrared radiation, low temperature resistance (∼ −40 °C), wide temperature range thermal responsiveness (∼ −25–60 °C), enabling effective regulation of solar heat radiation. Additionally, the anionic-NIPAM complex hydrogel possesses a high diffusion coefficient of water and excellent conductivity of 13.38 mS cm−1, which can be expanded its application in the field of flexible ion-conductive sensors.

Fermi energy modulation by tellurium doping of thermoelectric copper(I) iodide

Copper(I) iodide (CuI) is the leading inorganic p-type transparent conductor, attracting major attention for its promising optoelectronic properties and facile growth methods, although, commercial uptake is limited due to its as-of-yet insufficient electrical conductivity. Doping CuI with the chalcogens (O, S, Se, Te) is a viable route to tune its electrical conductivity for applications such as in thin film transistors, hole transport layers in solar cells, and transparent thermoelectric generators. The heaviest chalcogen element, Te, is yet to be explored in heavily intrinsically p-type doped CuI at non-alloying concentrations, the subject of the present work. We report the effects of tellurium at the boundary between the doping and alloying regime (up to a maximum of 2.4 % Te) in CuI thin films and investigation the variation in the thermoelectric properties and electronic band structure of the material. Ion implanting tellurium into CuI led to a progressive reduction in the films' work functions from 4.9 eV to 4.5 eV while the ionization potential remained unchanged, measured through photoemission spectrometry. This signified a modulation of the Fermi energy relative to the valence band edge, having a major effect on the materials' electrical conductivity and Seebeck coefficient, the former decreasing by 3 orders of magnitude, while the latter increased by 80 %. We conducted density functional theory (DFT) calculations to elucidate the effect of tellurium doping on the band structure of CuI. Tellurium doping corroborated the shift of Fermi energy, the incorporation of impurity acceptor states deeper into the band gap, in addition to disordering the valence band maximum. This work shows that, the Fermi energy in heavily p-type doped CuI can be moved away from the valence band through Te doping in addition to introducing band disorder, useful for controlling the hosts’ transport properties.

Dual-phase competitive behavior in N-type Sn–Bi–Te thermoelectric films achieving high thermoelectric performance

The dual-phase competitive behavior is introduced as an effective strategy to optimize the physical and chemical properties of N-type Bi2Te3 thermoelectric (TE) materials. Controllable SnTe-embedded Bi2Te3 nanocomposites can be synthesized with the addition of excessive Sn into Bi2Te3 by tuning the crystallization behavior under proper thermal heating temperature. Notably, the precipitation temperature of Bi2Te3 increases from 473 ​K for Sn20.9(Bi2Te3)79.1 to 573 ​K for Sn34.4(Bi2Te3)65.6, expanding the controllable temperature span for the presence of SnTe phase. The second-phase nanoprecipitate SnTe can improve electrical conductivity by competing with the Bi2Te3 phase, achieving an increase of four orders of magnitude at the critical temperature of ∼500 ​K. Simultaneously, it increases the interfacial energy filtration effect between nanocrystalline grains, decoupling electrical parameters between conductivity and Seebeck coefficient. Consequently, the high power factor of ∼147 ​μW/mK2 at 650 ​K for optimized Sn26.6(Bi2Te3)73.4 films can be obtained, which is more than twice that of the pure Bi2Te3 material. Our work demonstrates a new physical mechanism to unravel the complicated structure-property relationship by dual-phase competitive behavior during phase transition. This study fills the gap in knowledge on the effects of the SnTe phase regarding the Bi2Te3 system and provides guidance for the innovative design of high-performing inorganic thermoelectrics.

Advanced, high‐performance thermo‐insulating plaster

AbstractThe main purpose of many current studies regarding energy efficiency is the improvement of the thermal resistance of buildings. To fulfill this goal, the development of advanced insulating materials, to be incorporated in the building envelopes, is imperative. Aerogels are ultralight porous materials typically produced via the sol‐gel process followed by supercritical drying of the wet gel. They exhibit very high porosities and a mesoporous‐macroporous structure which endows aerogels with extremely low thermal conductivity. This makes them ideal candidates for ambient thermal insulation applications. However, the cost for aerogel insulation is considerably higher than the one of standard insulation products. In the present work, highly porous aerogel‐like materials based on silica and commercial novolac resin were developed and added to common mortars. The prepared materials were dried under ambient pressure to minimize the manufacturing cost. The bulk density of silica quasi‐aerogels was 0.03 g/cm3–0.09 g/cm3 and that of the novolac resin samples 0.09 g/cm3–0.21 g/cm3. The aerogels were incorporated in mortars and cured for 28 days before measurement of thermal conductivity. The values of the thermal conductivity coefficient of the measured samples were 0.047 W/m K–0.058 W/m K for the silica reinforced mortars and 0.036 W/m K–0.044 W/m K for the novolac reinforced ones.