Coaxial Antenna Research Articles

Integrated Couplers of THz Radiation for Helical Slow-Wave Structures.

We have designed an integrated device that couples input and output coaxial horn antennas with a self-assembled helical slow-wave structure cradled in a v-groove on a silicon-on-insulator wafer. These devices will potentially enable the characterization of cold parameters and beam-wave interaction in slow-wave structures on a wafer level, i.e., without having to dice and package individual devices. In addition, such vertically integrated antennas and helical slow-wave structures may form the basis of compact and low-cost traveling-wave tube amplifiers operating at THz frequencies.

Testing and Analysis of PIM Performance in a Passive DAS Network - Experimental Approach

Passive intermodulation (PIM) poses a significant challenge in telecommunication networks, with potentially severe impacts on network performance and signal integrity if not addressed during the initial deployment phase. This study investigates PIM levels within a passive distributed antenna system (DAS) network for cellular mobile radio communication across multiple floors of a building. The network comprises coaxial cables, connectors, splitters, combiners, and antennas structured in a systematic plan. This work used the experimental method to test for PIM in the network used for this investigation. Designed as a multicarrier system, it handles RF signals across frequencies of 700/850MHz, 1900MHz, 2100MHz, and 2600MHz. On-site PIM testing was conducted during the network deployment phase to analyze the behavior of high-power RF signals. Utilizing Kaelus iQA-1921C and iQA 850C series PIM analyzers, tests were conducted following known industry codes and standards. High RF power was preset to 43dBm for full band, 35dBm for high bands, and 25dBm for low band. The test equipment was calibrated on high PIM load and low PIM load. Test points were selected at both vertical and horizontal subsystem cabling structures, focusing on riser cables. The standard baseline performance PIM levels was set to -150dBc. The analysis focused on examining the characteristics of PIM signals captured via time-domain PIM traces, investigating the impact of altering the frequency of the two-tone signal on the IM3 frequency component, and highlighting the importance of selecting an appropriate frequency for the two-tone signal that is not positioned near the edges. Results were based on pass or fail test, and resolution measures were taken to mitigate interference.

Effect of high blood flow on heat distribution and ablation zone during microwave ablation-numerical approach.

Microwave ablation has become a viable alternative for cancer treatment for patients who cannot undergo surgery. During this procedure, a single-slot coaxial antenna is employed to effectively deliver microwave energy to the targeted tissue. The success of the treatment was measured by the amount of ablation zone created during the ablation procedure. The significantly large blood vessel placed near the antenna causes heat dissipation by convection around the blood vessel. The heat sink effect could result in insufficient ablation, raising the risk of local tumor recurrence. In this study, we investigated the heat loss due to large blood vessels and the relationship between blood velocity and temperature distribution. The hepatic artery, with a diameter of 4 mm and a height of 50 mm and two branches, is considered in the computational domain. The temperature profile, localized tissue contraction, and ablation zones were simulated for initial blood velocities 0.05, 0.1, and 0.16 m/s using the 3D Pennes bio-heat equation, temperature-time dependent model, and cell death model, respectively. Temperature-dependent blood velocity is modeled using the Navier-Stokes equation, and the fluid-solid interaction boundary is treated as a convective boundary. For discretization, we utilized elements for the wave propagation model, elements for the Pennes bio-heat model, and elements for the Navier-Stokes equation, where represents the computational domain. The simulated results show that blood vessels and blood velocity have a significant impact on temperature distribution, tissue contraction, and the volume of the ablation zone.

Various Parameter Measurements in Single-Frequency Dual-ECR Heating on Electron Cyclotron Resonance Ion Source

We have been researching efficient generation of multi-charged ions on electron cyclotron resonance ion source (ECRIS). We can introduce microwaves from a coaxial antenna at the upstream side of the magnetic mirror field (Coaxial) and a rod antenna at the downstream side (Rod). Regardless of R-wave cutoff, ECR occurs at two resonance points by Dual-ECR heating which means introducing microwaves from both antennas and we succeeded in generating more multi-charged Ar ions. We measured beam currents and plasma parameters such as electron density and electron temperature and obtained their radial distributions. We found the beam currents of multi-charged Ar ions were highest by Dual-ECR heating.

First Results from a Broadband Search for Dark Photon Dark Matter in the 44 to 52 μeV Range with a Coaxial Dish Antenna.

We present first results from a dark photon dark matter search in the mass range from 44 to 52 μeV (10.7-12.5GHz) using a room-temperature dish antenna setup called GigaBREAD. Dark photon dark matter converts to ordinary photons on a cylindrical metallic emission surface with area 0.5 m^{2} and is focused by a novel parabolic reflector onto a horn antenna. Signals are read out with a low-noise receiver system. A first data taking run with 24days of data does not show evidence for dark photon dark matter in this mass range, excluding dark photon photon mixing parameters χ≳10^{-12} in this range at 90% confidence level. This surpasses existing constraints by about 2 orders of magnitude and is the most stringent bound on dark photons in this range below 49 μeV.

Numerical study of the induction of intratumoral apoptosis under microwave ablation by changing slot length of microwave coaxial antenna.

Recent advances in technology have led to an increase in the detection of previously undetected deep-located tumor tissue. As a result, the medical field is using a variety of methods to treat deep-located tumors, and minimally invasive treatment techniques are being explored. In this study, therapeutic effect of microwave ablation (MWA) on tumor generated inside liver tissue was analyzed through numerical analysis. The distribution of electromagnetic fields in biological tissues emitted by microwave coaxial antenna (MCA) was calculated through the wave equation, and the thermal behavior of the tissue was analyzed through the Pennes bioheat equation. Among various treatment conditions constituting MWA, tumor radius and the slot length inside the MCA were changed, and the resulting treatment effect was quantitatively confirmed through three apoptotic variables. As a result, each tumor radius has optimal power condition for MWA, 2.6W, 2.4W, and 3.0W respectively. This study confirmed optimal therapeutic conditions for MWA. Three apoptotic variables were used to quantitatively identify apoptotic temperature maintenance inside tumor tissue and thermal damage to surrounding normal tissue. The findings of this study are expected to serve as a standard for treatment based on actual MWA treatment.

Numerical Analysis of Therapeutic Effects by Varying Slot Numbers and Slot‐to‐Slot Distance in Microwave Ablation Using Multislot Coaxial Antenna

Microwave ablation (MWA) is based on the energy absorbed by biological tissue through microwave emission, which raises the temperature of the tumor to perform the treatment. MWA has the advantage of causing minimal bleeding and treating deep tumors. In this study, MWA for various slot design situations in a microwave coaxial antenna (MCA) was simulated through numerical analysis. For the slot design, the number of slots and the distance between slots were determined by the analysis parameters. A tumor developed inside the liver tissue was implemented, and the temperature distribution of the tumor and surrounding liver tissue was calculated for all cases selected for numerical analysis. The Helmholtz electromagnetic equation was used to calculate the electromagnetic field inside the tissue, and the modified Pennes bioheat equation was used to calculate the temperature change in the tissue due to the emitted microwave. Treatment effects were quantitatively analyzed for each slot design condition through an apoptotic variable based on the calculated temperature distribution. Lastly, conditions that produce optimal treatment effects were derived depending on the number of slots. The analysis showed that as the distance between the slots increased from 0.5 to 3.5 mm, the optimal treatment effect was obtained when the number of slots was 4, 3, 3, and 2, respectively, and the microwave input power at that time was 3.0, 2.8, 2.6, and 3.0 W, respectively. This is expected to allow for more rigorous and more therapeutically effective MWA.

Feasibility Study of Numerical Calculation and Machine Learning Hybrid Approach for Renal Denervation Temperature Prediction

Transcatheter renal denervation (RDN) is a novel treatment to reduce blood pressure in patients with resistant hypertension using an energy-based catheter, mostly radio frequency (RF) current, by eliminating renal sympathetic nerve. However, several inconsistent RDN treatments were reported, mainly due to RF current narrow heating area, and the inability to confirm a successful nerve ablation in a deep area. We proposed microwave energy as an alternative for creating a wider ablation area. However, confirming a successful ablation is still a problem. In this paper, we designed a prediction method for deep renal nerve ablation sites using hybrid numerical calculation-driven machine learning (ML) in combination with a microwave catheter. This work is a first-step investigation to check the hybrid ML prediction capability in a real-world situation. A catheter with a single-slot coaxial antenna at 2.45 GHz with a balloon catheter, combined with a thin thermometer probe on the balloon surface, is proposed. Lumen temperature measured by the probe is used as an ML input to predict the temperature rise at the ablation site. Heating experiments using 6 and 8 mm hole phantom with a 41.3 W excited power, and 8 mm with 36.4 W excited power, were done eight times each to check the feasibility and accuracy of the ML algorithm. In addition, the temperature on the ablation site is measured for reference. Prediction by ML algorithm agrees well with the reference, with a maximum difference of 6 °C and 3 °C in 6 and 8 mm (both power), respectively. Overall, the proposed ML algorithm is capable of predicting the ablation site temperature rise with high accuracy.

Evaluation of coaxial dipole antennas as transceiver elements of human head array for ultra-high field MRI at 9.4T.

The aim of this work is to evaluate a new eight-channel transceiver (TxRx) coaxial dipole array for imaging of the human head at 9.4T developed to improve specific absorption rate (SAR) performance, and provide for a more compact and robust alternative to the state-of-the art dipole arrays. First, the geometry of a single coaxial element was optimized to minimize peak SAR and sensitivity to the load variation. Next, a multi-tissue voxel model was used to numerically simulate a TxRx array coil that consisted of eight coaxial dipoles with the optimal configuration. Finally, we compared the developed array to other human head dipole arrays. Results of numerical simulations were verified on a bench and in the scanner including in vivo measurements on a healthy volunteer. The developed eight-element coaxial dipole TxRx array coil showed up to 1.1times higher SAR-efficiency than a similar in geometry folded-end and fractionated dipole array while maintaining whole brain coverage and low sensitivity of the resonance frequency to variation in the head size. As a proof of concept, we developed and constructed a prototype of a 9.4T (400 MHz) human head array consisting of eight TxRx coaxial dipoles. The developed array improved SAR-efficiency and provided for a more compact and robust alternative to the folded-end dipole design. To the best of our knowledge, this is the first example of using coaxial dipoles for human head MRI at ultra-high field.

A Rigorous Explicit Expression for the Mutual Inductance of Two Co-Axial Thin-Wire Coil Antennas Placed above a Layered Ground

This paper presents a quasi-analytical method that allows the derivation of a rigorous series-form representation for the mutual inductance of two co-axial coil antennas located above an arbitrarily layered earth structure. Starting from Biot–Savart law, which gives the integral representation for the primary vector potential generated by the source coil, the potential reflected by the layered ground is derived, and the resulting total vector potential is then integrated along the external circumference of the receiving coil to give the mutual inductance of the two antennas. The obtained representation for the flux is then evaluated analytically through the usage of the Gegenbauer addition theorem once an accurate, rational approximation is used in place of the factor of the integrand that exhibits branch cuts. It is shown how the resulting explicit solution exhibits the same degree of accuracy as purely numerical approaches like the finite-difference time-domain (FDTD) method and conventional numerical quadrature schemes, while it is less time-demanding than the latter methods.

Study on microwave heating energy supplement technology for gas hydrate reservoir

This study proposes a microwave heating energy supplement technology for gas hydrate reservoir. The microwave radiation simulation model of the leaky coaxial antenna is established by HFSS. Based on the simulation results of microwave antenna structure parameters on the radiation performance, the optimized shape, angle, length, width and fillet of the slot are rectangle, 80°, 38 mm, 12 mm and 2 mm, respectively. To compare the heating performance of microwave antenna before and after optimization, a microwave heating simulation model for hydrate reservoir is developed, which is validated by experimental results. The comparison results illustrate that, after microwave heating 10 h with the optimized antenna structure, the average temperature within a 1-m radius of natural gas hydrate reservoir increases to 10.613 °C, which is about 5.5 °C higher than that before the optimization. The aforementioned results suggest that the optimized microwave antenna structure significantly increases the temperature of the hydrate reservoir, providing the necessary energy to drive hydrate decomposition. The proposed microwave energy supplementation technique holds promise for advancing the efficient development of natural gas hydrates, the further investigation of effect of which on gas production within hydrate reservoirs is needed for future application.

Intracavitary Applicator for Sequential Delivery of Localized Hyperthermia Through Non-Metallic Uterine Tandem.

In this work, we report the design and demonstration of a flexible coaxial wire antenna with a low profile flexible choke for delivering localized hyperthermia (HT) treatment to the cervix through a custom designed uterine tandem applicator. Resistive and magnetic materials were investigated for determining the flexible choke design suited for intracavitary HT treatment at 915 MHz. Measurements of the intracavitary antenna with the flexible choke in tissue mimicking phantom and ex-vivo bovine muscle through the non-metallic uterine tandem prototype confirm the ability to deliver localized HT to the cervix at 915 MHz and 50 mm insertion depth.

Optimal design of aperiodic tri-slot antennas for the conformal ablation of liver tumors using an experimentally validated MWA computer model

ObjectiveThis study aims to demonstrate that the conformal microwave ablation (MWA) of liver tumors could be attained by optimizing the structure of an aperiodic tri-slot coaxial antenna, its insertion depth, and input power. MethodsA computational MWA model with an aperiodic tri-slot coaxial antenna operating at the frequency of 2.45 GHz was built and validated by both an ex vivo and a pilot in vivo experiment with porcine healthy livers. The validated in vivo computational MWA model implemented with a liver tumor was then used as a testbed to investigate the conformal ablation of liver tumors. Five liver tumors in different sizes and shapes were investigated. A genetic algorithm optimization method (NSGA-II) was used to optimize the structure of antenna, insertion depth of antenna, and microwave antenna input power for the conformal ablation of liver tumors. ResultsThe validation results showed that a good agreement in both the spatiotemporal temperature distribution and ablation zone was found between the computer model and the ex vivo experiments at both 45 W, 5 min and 60 W, 3 min treatments and the in vivo experiment at 45 W, 5 min treatment. The optimized simulation results confirmed that five cases of liver tumors in different sizes and shapes can be conformally ablated by optimizing the aperiodic tri-slot coaxial antenna, antenna insertion depth, and microwave antenna input power. ConclusionThis paper demonstrates that the aperiodic tri-slot coaxial antenna can be optimized with the insertion depth and input power for the conformal ablation of liver tumors, regardless the size and shape of liver tumors.

The Evolution of Microwave-Induced Thermoacoustic Signals Generated During Pulsed Microwave Ablation in Bovine Liver

The temperature dependence of microwave-induced thermoacoustic signals generated in tissue may be exploited to monitor microwave ablation in real-time. We present an experimental study investigating the evolution of microwave-induced thermoacoustic signals that are generated within an ablation zone during microwave ablation in bovine liver tissue. An X-band interstitial coaxial ablation antenna is used to simultaneously heat liver tissue to temperatures up to 90 <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">$^{\circ }$</tex-math></inline-formula> C and excite thermoacoustic signals via the absorption of pulsed microwave energy. Thermoacoustic signals are detected using a single-element ultrasound transducer located at the surface of the tissue. Both fresh and boiled liver tissue samples are used in experiments to decouple the influence of temperature and tissue coagulation on thermoacoustic signal characteristics. We identify two thermoacoustic signal characteristics of interest: arrival time of the pulse at the ultrasound receiver and the energy in the pulse. We find that the time difference of arrival over the course of microwave ablation grows in magnitude due to temperature-dependent speed of sound and tissue shrinkage. Thermoacoustic signal energy generally increases throughout microwave ablation, implying an increasing temperature-dependent thermal expansion coefficient of liver tissue. Of the two characteristics, time difference of arrival shows the most promise as a trackable feature for monitoring microwave ablation in real time.

Anisotropy evaluation and interface detection based on 3D holographic azimuthal electromagnetic resistivity logging instrument

Abstract 3D holographic azimuthal electromagnetic resistivity logging-while-drilling (LWD) is a convenient and efficient technology to obtain information about formation. It has the advantages of being instant and accurate. It can be applied to fields of engineering such as evaluating anisotropy and detecting nearby geological interfaces. A 3D electromagnetic resistivity azimuthal LWD instrument consists of coaxial, coplanar, tilted and orthogonal antenna systems, being able to solve for all nine components. The explicit generic formulation is derived from presenting the response for a basic unit of one arbitrarily oriented transmitter and one arbitrarily oriented receiver. Combining the responses of basic units with different transmitter-receiver spacing and different components, an ‘anisotropy signal’ is defined with the phase difference ${M}_{px}$ and amplitude ratio ${M}_{ax}$. A ‘boundary signal’ is also defined with the phase difference ${M}_{pz}$ and amplitude ratio ${M}_{az}$. Forward simulation results show that the 2MHz ${M}_{px}$ can accurately identify geological anisotropy in highly deviated and horizontal wells. The ${M}_{az}$ can detect geological interfaces in highly deviated and horizontal wells. the 100 kHz${\rm{\ }}{M}_{az}\ $can detect geological boundaries in the range of 8–9 m.

Finite Element Analysis of Microwave Tumor Ablation Based on Open-Source Software Components

Microwave ablation is a procedure for treating various types of cancers during which a small needle-like probe is inserted inside the tumor, which delivers microwave energy, causes tissue heating, and effectively produces necrosis of the tumor tissue. Mathematical models of microwave ablation involve the modeling of multiple physical phenomena that occur during the procedure, including electromagnetic wave propagation, heat transfer, and tissue damage. In this study, a complete model of a microwave ablation procedure based on open-source software components is presented. First, the comprehensive procedure of mesh creation for the complete geometric arrangement of the microwave ablation, including a multi-slot coaxial antenna, a real liver tumor taken from the database, and the surrounding liver tissue, is described. It is demonstrated that utilizing smart meshing procedures significantly reduces the usage of computational resources and simulation time. An accurate custom explicit Euler time loop was designed to obtain temperature values and estimate tissue necrosis across the computational domain during the time of microwave ablation. The simulation results obtained by solving the electromagnetic field using the finite element method in the frequency domain are presented and analyzed. The simulation was performed for a microwave frequency of 2.45 GHz, and the volumetric distribution of temperature and estimation of cell damage over 600 s are presented.

Stereoscopic UWB Yagi-Uda Antenna with Stable Gain by Metamaterial for Vehicular 5G Communication.

In this paper, a stereoscopic ultra-wideband (UWB) Yagi-Uda (SUY) antenna with stable gain by near-zero-index metamaterial (NZIM) has been proposed for vehicular 5G communication. The proposed antenna consists of magneto-electric (ME) dipole structure and coaxial feed patch antenna. The combination of patch antenna and ME structure allows the proposed antenna can work as a Yagi-Uda antenna, which enhances its gain and bandwidth. NZIM removes a pair of C-notches on the surface of the ME structure to make it absorb energy, which results in two radiation nulls on both sides of the gain passband. At the same time, the bandwidth can be enhanced effectively. In order to further improve the stable gain, impedance matching is achieved by removing the patch diagonally; thus, it is able to tune the antenna gain of the suppression boundary and open the possibility to reach the most important characteristic: a very stable gain in a wide frequency range. The SUY antenna is fabricated and measured, which has a measured -10 dBi impedance bandwidth of approximately 40% (3.5-5.5 GHz). Within it, the peak gain of the antenna reaches 8.5 dBi, and the flat in-band gain has a ripple lower than 0.5 dBi.

Ultrasound and Microwave-Assisted Synthesis of Hexagonally Ordered Ce-Promoted Mesoporous Silica as Ni Supports for Ethanol Steam Reforming

Solvothermal synthesis of mesoporous materials based on amphiphilic molecules as structure-directing agents can be enhanced using non-conventional technologies for stirring and thermal activation. Here, we disclose a green synthesis approach for the preparation of cerium-modified hexagonally ordered silica sieves. Ultrasound micromixing enabled us to obtain well-dispersed Ce in the self-assembled silica network and yielded ordered materials with high cerium content (Ce/Si molar ratio = 0.08). Microwave dielectric heating, applied by an innovative open-end coaxial antenna, was used to reduce the overall hydrothermal synthesis time and to improve the surface area and textural properties. These mesoporous materials were used as a Ni catalyst support (10 wt.% metal loading) for the ethanol steam reforming reaction. The new catalysts featured complete ethanol conversion, high H2 selectivity (65%) and better stability, compared to the same catalyst prepared with magnetic stirring and conventional heating. The Ce-promoted silica sieves offered a suitable support for the controlled growth of nanocarbon that does not result in catalyst deactivation or poisoning after 6 h on stream.

Thermoacoustic signals generated from pulsed microwave ablation in liver tissue

Microwave-induced thermoacoustic signals are generated when pulsed microwave energy is absorbed by tissue. Thermoacoustic signals contain information about the electromagnetic, thermal, and acoustic material properties of the tissue. Thus, we propose using microwave-induced thermoacoustic signals to monitor microwave ablation, a thermal therapy used to heat and kill malignant tissue, in real-time. Conventional microwave-induced thermoacoustic signals are excited using an external waveguide. Our approach excites thermoacoustic signals via pulsed microwave energy delivered by the already present interstitial microwave ablation antenna. In this talk, we will present the experimental investigation of the evolution of microwave-induced thermoacoustic signals generated during microwave ablation in bovine liver tissue. Pulsed microwave energy was delivered via a narrow-diameter coaxial ablation antenna to simultaneously ablate tissue and excite thermoacoustic signals. Trials were conducted in room-temperature fresh liver tissue as well as room-temperature boiled liver tissue to investigate the influence of ablative temperature rise and tissue coagulation on thermoacoustic signals. Our experimental results show thermoacoustic signal characteristics change throughout the course of microwave ablation that could potentially be used for monitoring the microwave ablation process.

SICL-Fed Balanced Antipodal Dipole Antenna With Wideband Operation and Cross-Polarization Improvement at Millimeter-Wave Band

A substrate integrated coaxial line-fed balanced antipodal dipole antenna array is proposed for millimeter-wave (MMW) applications in this letter. Different from the traditional dual-armed dipole antenna, a balanced antipodal dipole element with three arms is proposed to improve the cross-polarization level by canceling the vertically polarized electric-field components. A cross-polarization level of less than −20 dB is achieved over the entire frequency band. Meanwhile, a gap is etched on each dipole arm to achieve dual-mode operation and broaden the impedance bandwidth of the dipole element, and an impedance bandwidth of more than 65% is obtained. By combining the proposed dipole elements with the unequal feeding network, a 1 × 8 dipole antenna array is designed, fabricated, and measured. The measured results show that the proposed dipole antenna array can achieve a wide −10 dB impedance bandwidth of more than 54% from 24.5 to 43 GHz, a sidelobe level of low than −18 dB in E-plane, and a cross-polarization level of low than −20 dB. With the merits of wide operating bandwidth, low cross-polarization level, low sidelobe level, low profile, and easy integration, the proposed antenna array is valuable to advanced MMW communication systems.