Coaptation Area Research Articles

Improved Geometry of Decellularized Tissue Engineered Heart Valves to Prevent Leaflet Retraction.

Recent studies on decellularized tissue engineered heart valves (DTEHVs) showed rapid host cell repopulation and increased valvular insufficiency developing over time, associated with leaflet shortening. A possible explanation for this result was found using computational simulations, which revealed radial leaflet compression in the original valvular geometry when subjected to physiological pressure conditions. Therefore, an improved geometry was suggested to enable radial leaflet extension to counteract for host cell mediated retraction. In this study, we propose a solution to impose this new geometry by using a constraining bioreactor insert during culture. Human cell based DTEHVs (n = 5) were produced as such, resulting in an enlarged coaptation area and profound belly curvature. Extracellular matrix was homogeneously distributed, with circumferential collagen alignment in the coaptation region and global tissue anisotropy. Based on in vitro functionality experiments, these DTEHVs showed competent hydrodynamic functionality under physiological pulmonary conditions and were fatigue resistant, with stable functionality up to 16 weeks in vivo simulation. Based on implemented mechanical data, our computational models revealed a considerable decrease in radial tissue compression with the obtained geometrical adjustments. Therefore, these improved DTEHV are expected to be less prone to host cell mediated leaflet retraction and will remain competent after implantation.

Saddle-Shaped Annuloplasty Improves Leaflet Coaptation in Repair for Ischemic Mitral Regurgitation

Current repair results for ischemic mitral regurgitation (IMR) with undersized annuloplasty rings are characterized by high IMR recurrence rates. Current annuloplasty rings treat annular dilatation, but they do little to improve (and may actually exacerbate) leaflet tethering. New saddle-shaped annuloplasty rings have been shown to maintain or restore a more physiologic annular and leaflet geometry and function. Using a porcine IMR model, we sought to demonstrate the influence of annuloplasty ring shape on leaflet coaptation. Eight weeks after posterolateral infarct, eight pigs with grade 2+ or higher IMR were randomized to undergo either a 28-mm flat ring annuloplasty (n = 4) or a 28-mm saddle-shaped ring annuloplasty (n = 4). Real-time three-dimensional echocardiography and a customized image analysis protocol allowed three-dimensional assessment of leaflet coaptation before and after annuloplasty. Total leaflet coaptation area was significantly higher after saddle-shaped ring annuloplasty (109.6 ± 26.9 mm(2)) compared with flat ring annuloplasty (46.2 ± 7.7 mm(2), p <0.01). After annuloplasty, total coaptation area decreased by 87.5 mm(2) (or 65%) in the flat annuloplasty group (p = 0.01), whereas total coaptation area increased by 22.2 mm(2) (or 25%) in the saddle-shaped annuloplasty group (p = 0.28). This study shows that the use of undersized saddle-shaped annuloplasty rings in mitral valve repair for IMR improves leaflet coaptation, whereas the use of undersized flat annuloplasty rings worsens leaflet coaptation. Because one of Carpentier's fundamental principles of mitral valve repair (durability) is to create a large surface of coaptation, saddle-shaped annuloplasty may increase repair durability.

Innervated Free Groin Flap.

Innervated Free Groin Flap.

Posterior annulus shortening increases leaflet coaptation in ischemic mitral incompetence: a new and valid technique.

We introduce a technique of posterior annulus shortening to augment leaflet coaptation which addresses the restrictive mitral leaflet mobility in ischemic mitral incompetence (IMI), and report its long-term outcome. Between 1992 and 2012, 75 patients (mean age, 64.6±10.4 years; median, 66.0 years; range, 35.0-86.1 years) underwent repair of IMI by posterior annulus shortening to augment leaflet coaptation surface area. This technique reduces the annular diameter to between 23 and 25 mm and decreases the valve orifice to between 3.5 to 4.5 cm(2), which is sufficient to ensure an adequate leaflet coaptation area. An untreated pericardial strip is used to reinforce the shortened annulus in order to avoid redilatation. This augments the posterior leaflet by increasing the ratio of leaflet area/valve orifice where the coaptation gap is the greatest. The tissue strip increases and heightens the area which the posterior leaflet offers to the anterior leaflet for coaptation during closure, making valve closure possible in advanced leaflet restriction. During a mean follow-up of 7.62±0.66 (median 8.53, range, 3.6-20.9) years, New York Heart Association (NYHA) functional class significantly improved, left ventricular ejection fraction (LVEF) increased and there was a tremendous abatement of MI (P<0.01). Annular area was reduced from 9.2 to 5.8 cm(2). Coaptation area was increased from a complete lack thereof to 6.6 mm(2) post-repair. CT showed posterior annulus size reduction from 70.4 to 54 mm and an increase in posterior leaflet length from 15.9 to 19.6 mm. A remarkable CT finding was the increase in coaptation length from 5.2 to 8.2 mm. Eighteen-year freedom from moderate MI, freedom from reoperation and survival rates were 80.7%±9%, 84.9%±4.2% and 65.1%±6.3%, respectively. Posterior annulus shortening with pericardial strip augmentation addressing the lack of leaflet coaptation is a simple, reproducible and highly effective technique to restore valve competence in IMI.

Leaflet extension for repairing rheumatic mitral valve regurgitation.

It has been established that mitral valve (MV) repair is preferred over replacement in patients with mitral regurgitation (MR) caused by degenerative disease. In contrast, valve reconstruction for rheumatic MR remains controversial. Type IIIa MR due to rheumatic leaflet restriction often renders valve repair challenging and may predict a less successful repair. However, the utilization of leaflet mobilization and extension with autologous pericardium in order to increase leaflet area and surface of coaptation may achieve satisfactory results (1-3). This article represents our single-center experience of leaflet extension in rheumatic MR, with emphasis on description of the technique including tips on safeguards and pitfalls.

Subject-specific finite-element modeling of normal aortic valve biomechanics from 3D+t TEE images.

In the past decades, developments in transesophageal echocardiography (TEE) have opened new horizons in reconstructive surgery of the aortic valve (AV), whereby corrections are made to normalize the geometry and function of the valve, and effectively treat leaks. To the best of our knowledge, we propose the first integrated framework to process subject-specific 3D+t TEE AV data, determine age-matched material properties for the aortic and leaflet tissues, build a finite element model of the unpressurized AV, and simulate the AV function throughout a cardiac cycle. For geometric reconstruction purposes, dedicated software was created to acquire the 3-D coordinates of 21 anatomical landmarks of the AV apparatus in a systematic fashion. Measurements from ten 3D+t TEE datasets of normal AVs were assessed for inter- and intra-observer variability. These tests demonstrated mean measurement errors well within the acceptable range. Simulation of a complete cardiac cycle was successful for all ten valves and validated the novel schemes introduced to evaluate age-matched material properties and iteratively scale the unpressurized dimensions of the valves such that, given the determined material properties, the dimensions measured in vivo closely matched those simulated in late diastole. The leaflet coaptation area, describing the quality of the sealing of the valve, was measured directly from the medical images and was also obtained from the simulations; both approaches correlated well. The mechanical stress values obtained from the simulations may be interpreted in a comparative sense whereby higher values are indicative of higher risk of tearing and/or development of calcification.

Aortic valve adaptation to aortic root dilatation: insights into the mechanism of functional aortic regurgitation from 3-dimensional cardiac computed tomography.

The 3-dimensional relationship between aortic root and cusp is essential to understand the mechanism of aortic regurgitation (AR) because of aortic root dilatation (ARD). We sought to test the hypothesis that the stretched cusps in ARD enlarge to compensate for ARD. Computed tomography imaged 92 patients (57 with ARD, 29 with moderate to severe AR, 28 without significant AR) and 35 normal controls. Specialized 3-dimensional software measured individual cusp surface areas relative to maximal mid-sinus cross-sectional area and minimal 3-dimensional annular area, coaptation area fraction, and asymmetry of sinus volumes and intercommissural distances. Total open cusp surface area increased (P<0.001) from 7.6±1.4 cm(2)/m(2) in normals to 12.9±2.2 cm(2)/m(2) in AR-negative and 15.2±3.3 cm(2)/m(2) in AR-positive patients. However, the ratio of closed cusp surface area to maximal mid-sinus area, reflecting cusp adaptation, decreased from normals to AR-negative to AR-positive patients (1.38±0.20, 1.15±0.15, 0.88±0.15; P<0.001), creating the lowest coaptation area fraction. Cusp distensibility (closed diastolic versus open area) decreased from 20% in controls and AR-negative patients to 5% in AR-positive patients (P<0.001). Multivariate determinants of AR and coaptation area fraction reflected both sinus size and cusp-to-annular adaptation. ARD was also progressively asymmetrical with root size, and individual cusp surface areas failed to match this asymmetry. Aortic cusp enlargement occurs in ARD, but cusp adaptation and distensibility become limited in prominent, asymmetrical ARD, leading to AR. Optimal AR repair tailored to individual patient anatomy can benefit from appreciating valve adaptation and 3-dimensional relationships; understanding cusp adaptation mechanisms may ultimately provide therapeutic opportunities to improve such compensation.

The no-resection-technique for mitral valve repair in Barlow disease

Objectives: The resection technique for the repair of structural mitral valve pathology is common. However, new techniques recently performed follow the “Respect rather than Resect” approach. Our mitral valve repair technique aims at avoiding any resection of valve tissue in almost any pathology including complex cases of M. Barlow using artificial chordae as a universal solution. The idea is to achieve the highest possible coaptation area and preserve a normal leaflet motion to reach a repair for life.

Feasibility of In Vivo Human Aortic Valve Modeling Using Real-Time Three-Dimensional Echocardiography

Surgical techniques for aortic valve (AV) repair are directed toward restoring normal structural relationships in the aortic root and rely on detailed assessment of root and valve anatomy. Noninvasive three-dimensional (3D) imaging and modeling may assist in patient selection and operative planning. Transesophageal real-time 3D echocardiographic images of 5 patients with normal AVs were acquired. The aortic root and the annulus were manually segmented at end diastole using a 36-point rotational template. The AV leaflets and the coaptation zone were manually segmented in parallel 1-mm cross sections. Quantitative 3D models of the AV and root were generated and used to measure standard anatomic parameters and were compared to conventional two-dimensional echocardiographic measurements. All measurements are given as mean±SD. Annular, sinus, and sinotubular junction areas were 4.1±0.6 cm2, 7.5±1.2 cm2, and 3.9±1.0 cm2, respectively. Root diameters (measured in three locations) by 3D model inspection and two-dimensional echocardiography measurement correlated (R2=0.75). Noncoapted areas of the left, right, and noncoronary leaflets were 1.9±0.2 cm2, 1.6±0.3 cm2, and 1.6±0.3 cm2, respectively. Mean coaptation areas for the left-right, left-noncoronary, and right-noncoronary coaptation zones were 87.7±36.9 mm2, 69.9±20.7 mm2, and 114.2±23.0 mm2, respectively. The mean ratio of noncoapted leaflet area to annular area was 1.3±0.2. High-resolution 3D models of the in vivo normal human aortic root and valve were generated using 3D echocardiography. Quantitative 3D models and analysis may assist in characterization of pathology and decision making for AV repair.

Preparation of an autologous heart valve with a stent (stent‐biovalve) using the stent eversion method

We designed a novel method for constructing an autologous heart valve with a stent, called a stent-biovalve. In constructing completely autologous heart valves, named biovalves, which used in-body tissue architecture technology, tissues for leaflets were formed via ingrowths into narrow apertures in the preparation molds, frequently leading to delayed or incomplete biovalve preparation. In this technique, self-expandable nitinol stents after everting were mounted on an acrylic column-shaped part and partially covered with an acrylic cylinder-shaped part with three slits. This assembled mold was placed into subcutaneous abdominal pouches in beagles or goats for 4 weeks. Upon removing the acrylic parts after harvesting and trimming of capsulated tissues, a tubular hollow structure with three pocket-flaps of membranous tissue rigidly fixed to the stent's outer surface was obtained. Then, the stent was turned inside out to the original form, thus moving the pocket-flaps from outside to the inside. Stent-biovalves with a sufficient coaptation area were thus obtained with little tissue damage in all cases. The valve opened smoothly, and high aperture ratio was noted. This novel technique was thus highly effective in constructing a robust, completely autologous stent-biovalve with adequate valve function.

Abstract 18388: Novel Study of the Dynamic Changes in Mitral Valve Annular and Leaflet Parameters Under Varying Loading Conditions: A Three-Dimensional Echocardiographic Study

Background: The impact of changing loading conditions on mitral valve (MV) coaptation is controversial. Previous studies assessed the MV at mid or end-systole only, hence MV dynamic changes throughout systole are poorly understood. We used three-dimensional echocardiography (3DE) to explore dynamic changes in MV annular and leaflet parameters during loading stress and inotropy in an animal model. Methods: In open chest model, 8 pigs and 4 dogs were imaged epicardially. 3DE was performed at baseline, with dobutamine infusion, volume infusion and aortic constriction, with a return to baseline hemodynamics between each intervention. The 3DE datasets were analyzed offline using TomTec semi automated MV software. Leaflet (AL) and annular area (AA) were reported as % change from baseline in 5 systolic intervals (1-5; each representing 20% of systole). ANOVA was performed between each intervention and baseline, at the 5 intervals, with Dunnett’s correction. Results: At baseline, MV peak % change of AL and AA occurred during the 4th and 5th intervals respectively. Compared to baseline, dobutamine infusion % change AL was reduced (-5.9% ± 3.8 vs -9.4% ± 6.1, p&lt;0.01) in the 3rd interval, whilst % change AA was reduced throughout systole. With volume loading, % change AL and AA were significantly reduced during intervals 2 to 5. In contrast, with aortic constriction % change AL (-5.9% ± 3.8 vs -2.4% ± 4.8, p&lt;0.05) and %change AA (-1.6% ± 3.8 vs 1.5% ± 5.7, p&lt;0.05) were increased at the 3rd interval (see Figure). Conclusion: Peak MV annular contraction and leaflet apposition occurs in late systole. MV leaflet coaptation area improves in response to increased contractility and pre-load by increasing annular contraction and reducing unopposed leaflet surface. In contrast, increased afterload has the opposite effect on annular and leaflet size, potentially worsening coaptation. The timing of peak annular contraction and leaflet apposition has implications for the design of future MV studies.

Three-dimensional contrast echocardiography-guided alcohol septal ablation in hypertrophic obstructive cardiomyopathy

A 58-year-old woman with hypertrophic obstructive cardiomyopathy (HOC) was referred for contrast(c) echocardiography-guided alcohol septal ablation (ASA). Two-dimensional transthoracic echocardiography (TTE) showed a left ventricular outflow tract gradient of 157 mmHg and severe mitral regurgitation ( Panel A ; Supplementary data online, Video 1 ). Agitated X-ray contrast was injected in the septal artery ( Panel B ; arrow). Two-dimensional c-TTE study showed increased signal in the basal inferior septum ( Panel C ). Three-dimensional c-TTE showed that myocardial enhancement was mainly distributed at infero-septal and antero-septal basal segments ( Panel D ; Supplementary data online, Video 2 ) involving the co-aptation area between the septum and mitral valve and extending to right ventricle (RV). Three-dimensional c-TTE showed the enhancement following the RV moderator band …

Effects of valve geometry and tissue anisotropy on the radial stretch and coaptation area of tissue-engineered heart valves

Tissue engineering represents a promising technique to overcome the limitations of the current valve replacements, since it allows for creating living autologous heart valves that have the potential to grow and remodel. However, also this approach still faces a number of challenges. One particular problem is regurgitation, caused by cell-mediated tissue retraction or the mismatch in geometrical and material properties between tissue-engineered heart valves (TEHVs) and their native counterparts. The goal of the present study was to assess the influence of valve geometry and tissue anisotropy on the deformation profile and closed configuration of TEHVs. To achieve this aim, a range of finite element models incorporating different valve shapes was developed, and the constitutive behavior of the tissue was modeled using an established computational framework, where the degree of anisotropy was varied between values representative of TEHVs and native valves. The results of this study suggest that valve geometry and tissue anisotropy are both important to maximize the radial strains and thereby the coaptation area. Additionally, the minimum degree of anisotropy that is required to obtain positive radial strains was shown to depend on the valve shape and the pressure to which the valves are exposed. Exposure to pulmonary diastolic pressure only yielded positive radial strains if the anisotropy was comparable to the native situation, whereas considerably less anisotropy was required if the valves were exposed to aortic diastolic pressure.

GEOMETRIC DIFFERENCES IN MITRAL APPARATUS BETWEEN DIFFERENT TYPES OF ISCHEMIC MITRAL REGURGITANT JET: A COLOR DOPPLER REAL–TIME 3D TRANSESOPHAGEAL ECHOCARDIOGRAPHY STUDY

results: MR jet geometry was classified into the following 3 categories: a curtain-like jet along almost the entire mitral leaflet coaptation (30 pts), a central jet from the central leaflet coaptation area (25 pts), and two separate jets (10 pts; Figure A-C). No difference in mitral annular area was found between the three groups. Pts with a central jet had smaller coaptation distance and tenting area at medial and lateral (all p<0.01) than those with a curtain-like jet, whereas no differences in these parameters at central area between the two groups. Compared to pts without two separate jets, those with two separate jets had similar coaptation distance and tenting area. However, pts with two separate jets had greater coaptation length (overlap length of the anterior and posterior leaflet) at the central area than those with a curtain-like jet and a central jet (4.5±0.5 vs. 3.6±1.1, 4.5±0.5 vs. 3.4±0.7 mm, respectively, both p<0.001).

Simulation of transcatheter aortic valve implantation: a patient-specific finite element approach

Until recently, heart valve failure has been treated adopting open-heart surgical techniques and cardiopulmonary bypass. However, over the last decade, minimally invasive procedures have been developed to avoid high risks associated with conventional open-chest valve replacement techniques. Such a recent and innovative procedure represents an optimal field for conducting investigations through virtual computer-based simulations: in fact, nowadays, computational engineering is widely used to unravel many problems in the biomedical field of cardiovascular mechanics and specifically, minimally invasive procedures. In this study, we investigate a balloon-expandable valve and we propose a novel simulation strategy to reproduce its implantation using computational tools. Focusing on the Edwards SAPIEN valve in particular, we simulate both stent crimping and deployment through balloon inflation. The developed procedure enabled us to obtain the entire prosthetic device virtually implanted in a patient-specific aortic root created by processing medical images; hence, it allows evaluation of postoperative prosthesis performance depending on different factors (e.g. device size and prosthesis placement site). Notably, prosthesis positioning in two different cases (distal and proximal) has been examined in terms of coaptation area, average stress on valve leaflets as well as impact on the aortic root wall. The coaptation area is significantly affected by the positioning strategy ( − 24%, moving from the proximal to distal) as well as the stress distribution on both the leaflets (+13.5%, from proximal to distal) and the aortic wall ( − 22%, from proximal to distal). No remarkable variations of the stress state on the stent struts have been obtained in the two investigated cases.

In vitro assessment of available coaptation area as a novel metric for the quantification of tricuspid valve coaptation

Tricuspid regurgitation (TR) is associated with increased mortality in patients undergoing mitral valve repair. In recent decades, TR has been addressed using annuloplasty concomitantly with mitral valve repair by some surgeons. However, repair efficacy and durability are often suboptimal. Increased understanding of tricuspid valve coaptation and the effects of pathological and repair conditions may be useful to inform future repair design. In the present study, we propose a two-dimensional in vitro technique, available coaptation area (ACA), to quantify the area of each tricuspid leaflet available for coaptation. Preliminary results showed that annular dilatation caused a significant (p<0.05) decrease in anterior leaflet ACA (0.92±0.18cm2), and combined annular dilatation and papillary muscle (PM) displacement resulted in a significant decrease in posterior leaflet ACA (0.87±0.15cm2). Isolated PM displacement did not have a significant effect on ACA, and the septal leaflet showed no changed in ACA under the conditions tested. In addition to quantifying ACA, our technique allows for the detailed mapping of leaflet coaptation, which may be used to reveal specific sites of malcoaptation on each leaflet. Application of the ACA method in future studies may lead to the development of specialized tricuspid repair strategies and annuloplasty ring designs that target specific regions of the tricuspid valve based on underlying pathological conditions.

Impact of Pulmonary Hypertension on Tricuspid Valve Function

Pulmonary arterial hypertension (PAH) results in increased right ventricle (RV) afterload leading to RV remodeling, tricuspid regurgitation (TR), and RV failure. Though characterizing the mechanisms of TR in PAH may suggest new treatment strategies, the mechanisms leading to TR in PAH have not been characterized. In the present study, eleven porcine tricuspid valves were studied in an in vitro right heart simulator. Annular dilatations of 1.2 and 1.4 times normal area, papillary muscle (PM) displacement simulating concentric RV dilatation and eccentric RV dilatation due to concomitant left ventricle dysfunction, and two levels of PAH hemodynamics were simulated independently and in combination. Relative TR, tenting area (TA) along each coaptation line, and coaptation area (CA) of each leaflet were quantified. Results showed a significant increase (p ≤ 0.05) in TR with both increased mean pulmonary artery pressure (mPAP) and annular dilatation of 1.4 times normal. Increased mPAP significantly decreased TA but tended to increase CA, while PM displacement significantly increased TA but did not affect CA, suggesting competing effects of transvalvular pressure and leaflet tethering. Annular dilatation significantly decreased anterior and posterior CA but did not affect TA. These results may inform future TV repairs in PAH to reduce TR and improve RV hemodynamics.

Posterior Leaflet Augmentation in Ischemic Mitral Regurgitation Increases Leaflet Coaptation and Mobility

Restoring leaflet coaptation is the primary objective in repair of ischemic mitral regurgitation (IMR). The common practice of placing an undersized annuloplasty ring partially achieves this goal by correcting annular dilation; however, annular reduction has been demonstrated to exacerbate posterior leaflet tethering. Using a sheep model of IMR, we tested the hypothesis that posterior leaflet augmentation (PLA) combined with standard annuloplasty sizing increases leaflet coaptation more effectively than undersized annuloplasty alone. Eight weeks after posterobasal myocardial infarction, 15 sheep with 2+ or greater IMR underwent annuloplasty with either a 24-mm annuloplasty ring (24-mm group, n = 5), 30-mm ring (30-mm group, n = 5), or 30-mm ring with concomitant augmentation of the posterior leaflet (PLA group, n = 5). Using three-dimensional echocardiography, postrepair coaptation zone and posterior leaflet mobility were assessed. Leaflet coaptation length after repair was greater in the PLA group (4.1 ± 0.3 mm) and the 24-mm group (3.8 ± 0.5 mm) as compared with the 30-mm group (2.7 ± 0.6 mm, p < 0.01). Leaflet coaptation area was significantly greater in the PLA group (121.5 ± 6.6 mm(2)) as compared with the 30-mm group (77.5 ± 17.0 mm(2)) or the 24-mm group (92.5 ± 17.9 mm(2), p < 0.01). Posterior leaflet mobility was significantly greater in the PLA group as compared with the 30-mm group or the 24-mm group. Posterior leaflet augmentation combined with standard-sized annuloplasty enhances leaflet coaptation more effectively than either standard-sized annuloplasty or undersized annuloplasty alone. Increased leaflet coaptation after PLA provides redundancy to IMR repair, and may decrease incidence of both recurrent IMR and mitral stenosis.

Patient-specific simulation of a stentless aortic valve implant: the impact of fibres on leaflet performance

In some cases of aortic valve leaflet disease, the implant of a stentless biological prosthesis represents an excellent option for aortic valve replacement (AVR). In particular, if compared with the implant of mechanical valves, it provides a more physiological haemodynamic performance and a reduced thrombogeneticity, avoiding the use of anticoagulants. The clinical outcomes of AVR are strongly dependent on an appropriate choice of both prosthesis size and replacement technique, which is, at present, strictly related to surgeon's experience and skill. This represents the motivation for patient-specific finite element analysis able to virtually reproduce stentless valve implantation. With the aim of performing reliable patient-specific simulations, we remark that, on the one hand, it is not well established in the literature whether bioprosthetic leaflet tissue is isotropic or anisotropic; on the other hand, it is of fundamental importance to incorporate an accurate material model to realistically predict post-operative performance. Within this framework, using a novel computational methodology to simulate stentless valve implantation, we test the impact of using different material models on both the stress pattern and post-operative coaptation parameters (i.e. coaptation area, length and height). As expected, the simulation results suggest that the material properties of the valve leaflets affect significantly the post-operative prosthesis performance.

Influence of Chronic Tethering of the Mitral Valve on Mitral Leaflet Size and Coaptation in Functional Mitral Regurgitation

The purposes of this study were to examine whether tethering of the mitral leaflets affects coaptation in patients with functional mitral regurgitation (FMR) and to assess the interaction between the mitral coaptation and mitral regurgitation severity. Functional mitral regurgitation causes restriction of leaflet closure as a result of enhanced tethering of the mitral leaflets and papillary muscle (PM) displacement. Three-dimensional transesophageal echocardiography was performed in 44 patients with FMR related to the bilateral PM displacement and in 56 controls. The distance between the tip of the anterior or posterior PM and the intervalvular fibrosa were measured as the lateral or medial tethering length (TL) in midsystole. To evaluate the degree of coaptation, coaptation length (CL) at medial, middle, and lateral sites of mitral valve and an estimate of coaptation area (CA) were measured. The FMR group showed the significantly decreased CA (1.3 ± 0.4 cm(2) vs. 1.6 ± 0.4 cm(2), p = 0.005) and CL (medial 3.2 ± 0.9 mm vs. 4.8 ± 0.6 mm, middle 3.8 ± 1.3 mm vs. 5.8 ± 0.7 mm, lateral 3.3 ± 0.9 mm vs. 4.8 ± 0.6 mm; all p < 0.0001) compared with the controls. Each CL correlated negatively and significantly with both medial and lateral TL (all p < 0.0001). Annular area (p = 0.004) was significantly smaller and leaflet-to-annular area ratio (p < 0.0001) was significantly larger in patients with nonsignificant FMR than in the patients with significant (moderate to severe) FMR. Significant correlations were found between effective regurgitant orifice area and CA or each CL (all p < 0.0001). Coaptation decreased significantly in patients with FMR. The CL at each region was related to PM displacement and the indexes of coaptation were associated with mitral regurgitation severity.