Chip-based Electrophoresis Research Articles

Molar mass profiling of synthetic polymers by free-solution capillary electrophoresis of DNA-polymer conjugates.

The molar mass distribution of a polymer sample is a critical determinant of its material properties and is generally analyzed by gel permeation chromatography or more recently, by MALDI-TOF mass spectrometry. We describe here a novel method for the determination of the degree of polymerization of polydisperse, uncharged, water-soluble polymers (e.g., poly(ethylene glycol) (PEG)), based upon single-monomer resolution of DNA-polymer conjugates by free-solution capillary electrophoresis. This is accomplished by end-on covalent conjugation of a polydisperse, uncharged polymer sample (PEG) to a monodisperse, fluorescently labeled DNA oligomer, followed by electrophoretic analysis. The monodisperse, charged DNA "engine" confers to each conjugate an equal amount of electromotive force, while the varying contour lengths of the uncharged, polydisperse polymers engender different amounts of hydrodynamic drag. The balance of electromotive and hydrodynamic forces enables rapid, high-resolution separation of the DNA-polymer conjugates as a function of the size of the uncharged PEG tail. This provides a profile of the molar mass distribution of the original polymer sample that can be detected by laser-induced fluorescence through excitation of the dye-labeled DNA. We call this method free solution conjugate electrophoresis (FSCE). Theory-based analysis of the resulting electrophoresis data allows precise calculation of the degree of polymerization of the PEG portion of each conjugate molecule. Knowledge of the molecular mass of the uncharged polymer's repeat unit allows for direct calculation of the molar mass averages as well as sample polydispersity index. The results of these analyses are strikingly reminiscent of MALDI-TOF spectra taken of the same PEG samples. PEG samples of 3.4-, 5-, and 20-kDa nominal average molar mass were analyzed by FSCE and MALDI-TOF; the values of the molar mass averages, Mw and Mn, typically agree to within 5%. Measurements and molar mass calculations are performed without any internal standards or calibration. Moreover, when DNA-polymer conjugate analysis is performed in a chip-based electrophoresis system, separation is complete in less than 13 min. FSCE offers an alternative to MALDI-TOF for the characterization of uncharged, water-soluble polymers that can be uniquely conjugated to DNA.

Nanoliter-scale sample preparation methods directly coupled to polymethylmethacrylate-based microchips and gel-filled capillaries for the analysis of oligonucleotides

We are currently developing miniaturized, chip-based electrophoresis devices fabricated in plastics for the high-speed separation of oligonucleotides. One of the principal advantages associated with these devices is their small sample requirements, typically in the nanoliter to sub-nanoliter range. Unfortunately, most standard sample preparation protocols, especially for oligonucleotides, are done off-chip on a microliter-scale. Our work has focused on the development of capillary nanoreactors coupled to micro-separation platforms, such as micro-electrophoresis chips, for the preparation of sequencing ladders and also polymerase chain reactions (PCRs). These nanoreactors consist of fused-silica capillary tubes (10–20 cm×20–50 μm I.D.) with fluid pumping accomplished using the electroosmotic flow generated by the tubes. These reactors were situated in fast thermal cyclers to perform cycle sequencing or PCR amplification of the DNAs. The reactors could be interfaced to either a micro-electrophoresis chips via capillary connectors micromachined in polymethylmethacrylate (PMMA) using deep X-ray etching (width 50 μm; depth 50 μm) or conventional capillary gel tubes using zero-dead volume glass unions. For our chips, they also contained an injector, separation channel (length 6 cm; width 30 μm; depth 50 μm) and a dual fiber optic, near-infrared fluorescence detector. The sequencing nanoreactor used surface immobilized templates attached to the wall via a biotin–streptavidin–biotin linkage. Sequencing tracks could be directly injected into gel-filled capillary tubes with minimal degradation in the efficiency of the separation process. The nanoreactor could also be configured to perform PCR reactions by filling the capillary tube with the PCR reagents and template. After thermal cycling, the PCR cocktail could be pooled from multiple reactors and loaded onto a slab gel or injected into a capillary tube or microchip device for fractionation.