Charge Extraction Research Articles

Surface Planarization-Epitaxial Growth Enables Uniform 2D/3D Heterojunctions for Efficient and Stable Perovskite Solar Modules.

Two-dimensional/three-dimensional (2D/3D) halide perovskite heterojunctions are widely used to improve the efficiency and stability of perovskite solar cells. However, interfacial defects between the 2D and 3D perovskites and the poor coverage of the 2D capping layer still hinder long-term stability and homogeneous charge extraction. Herein, a surface planarization strategy on 3D perovskite is developed that enables an epitaxial growth of uniform 2D/3D perovskite heterojunction via a vapor-assisted process. The homogeneous charge extraction and suppression of interfacial nonradiative recombination is achieved by forming a uniform 2D/3D interface. As a result, a stabilized power output efficiency of 25.97% is achieved by using a 3D perovskite composition with a bandgap of 1.55eV. To demonstrate the universality of the strategy applied for different perovskites, the champion device based on a 1.57eV bandgap 3D perovskite results in an efficiency of 25.31% with a record fill factor of 87.6%. Additionally, perovskite solar modules achieve a designated area (24.04 cm2) certified efficiency of 20.75% with a high fill factor of 80.0%. Importantly, the encapsulated uniform 2D/3D modules retain 96.9% of the initial efficiency after 1246h operational tracking under 65 °C (ISOS-L-3 protocol) and 91.1% after 862h under the ISOS-O-1 protocol.

The impact of interfacial quality and nanoscale performance disorder on the stability of alloyed perovskite solar cells

AbstractMicroscopy provides a proxy for assessing the operation of perovskite solar cells, yet most works in the literature have focused on bare perovskite thin films, missing charge transport and recombination losses present in full devices. Here we demonstrate a multimodal operando microscopy toolkit to measure and spatially correlate nanoscale charge transport losses, recombination losses and chemical composition. By applying this toolkit to the same scan areas of state-of-the-art, alloyed perovskite cells before and after extended operation, we show that devices with the highest macroscopic performance have the lowest initial performance spatial heterogeneity—a crucial link that is missed in conventional microscopy. We show that engineering stable interfaces is critical to achieving robust devices. Once the interfaces are stabilized, we show that compositional engineering to homogenize charge extraction and to minimize variations in local power conversion efficiency is critical to improve performance and stability. We find that in our device space, perovskites can tolerate spatial disorder in chemistry, but not charge extraction.

Pyro-phototronic Effect Enhanced Self-Powered Photoresponse in Lead-Free Hybrid Perovskite.

Pyro-phototronic effect (PPE) can significantly boost the performance of hybrid perovskite (HPs) photodetectors due to the effective modulation of photogenerated charge carrier separations, transportation, and extraction. However, there are few reports on the application of PPE in lead-free HPs. Herein, a polar lead-free HP (1,3-BMACH)BiBr5 [1,3-BMACH = 1,3-bis(aminomethyl)cyclohexane] is synthesized and realized broadband self-powered photoresponse from X-rays to near-infrared (NIR) through the PPE. Particularly, this light-induced PPE in lead-free HPs breaks the limitation of the optical band gap, making them suitable for broadband self-powered photodetection. Under 405 nm illumination, compared with a purely photovoltaic system, Iphoto+pyro is boosted by 3100%, and R and D* are both enhanced by 260% after coupled PPE. It is particularly interesting that an obvious X-ray-induced PPE phenomenon is also observed, which endows (1,3-BMACH)BiBr5 with a high sensitivity of 154 μC Gy-1 cm-2 and a low detection limit of 307 nGy s-1 under the self-powered mode. The implementation of light-induced PPE from X-rays to NIR in lead-free HPs provides a new approach for constructing environmentally friendly, broadband, and self-powered optoelectronic devices in the future.

Suppressing Se Vacancies in Sb2Se3 Photocathode by In Situ Annealing with Moderate Se Vapor Pressure for Efficient Photoelectrochemical Water Splitting.

Sb2Se3 emerges as a promising material for solar energy conversion devices. Unfortunately, the common deep-level defect VSe (selenium vacancy) in Sb2Se3 results in a low solar conversion efficiency. The post selenization process has been widely adopted for suppressing VSe. However, the effect of selenization on suppressing VSe is often compromised and even more VSe are induced due to defect-correlation. Herein, high-quality Sb2Se3 films are prepared using an unconventional selenization process, with precisely regulating in situ annealing Se vapor pressure. It is found that moderate Se vapor pressure annealing can efficiently suppress VSe by overcoming defect-correlation, as well as promotes grain growth and forms a better heterojunction band alignment. Consequently, the Sb2Se3 photocathode shows a high-level photocurrent of 19.5 mA cm-2 at 0 VRHE, an onset potential of 0.40 VRHE and a half-cell solar-to-hydrogen conversion efficiency of 1.9%, owing to the inhibited charge recombination, excellent charge transport and interface charge extraction. This work provides a significant insight to suppress deep-level defect VSe by adjusting Se vapor pressure for efficient Sb2Se3 photocathode.

Template-Assisted Growth of High-Quality α-Phase FAPbI3 Crystals in Perovskite Solar Cells Using Thiol-Functionalized MoS2 Nanosheets.

Formamidinium lead iodide (FAPI) has gained attention for hybrid perovskite solar cell (PSC) applications due to its enhanced stability and narrow bandgap. However, a significant challenge remains in inducing and stabilizing the elusive perovskite "black phase"─photoactive cubic α-FAPI─as the relatively bulky FA+ cations tend to favor the thermodynamically stable nonphotoactive "yellow phase". In this study, we present a templated growth strategy employing thiol-functionalized MoS2 nanosheets as templates. By introduction of 3-mercaptopropionic acid (MPA)-functionalized MoS2 as a growth template, precise control over crystal formation was achieved, favoring the growth of high-quality α-FAPI films. These advanced templated films exhibited substantial improvements in charge transport properties, efficient light absorption, and enhanced charge extraction. As a result, the PSCs achieved a significantly enhanced power conversion efficiency (PCE) compared to the nontemplated control device, increasing from 20.6 to 22.5%. The MoS2-incorporated device also demonstrated excellent shelf stability, maintaining 91% of the initial PCE even after 1600 h of storage without device encapsulation.

Tailored Polymer Hole-Transporting Materials with Multisite Passivation Functions for Effective Buried-Interface Engineering of Inverted Quasi-2D Perovskite Solar Cells.

Although quasi-2D Ruddlesden‒Popper (RP) perovskite exhibits advantages in stability, their photovoltaic performance are still inferior to 3D counterparts. Optimizing the buried interface of RP perovskite and suppress energetic losses can be a promising approach for enhancing efficiency and stability of inverted quasi-2D RP perovskite solar cells (PSCs). Among which, constructing polymer hole-transporting materials (HTMs) with defect passivation functions is of great significance for buried-interface engineering of inverted quasi-2D RP PSCs. Herein, by employing side-chain tailoring strategy to extend the π-conjugation and regulate functionality of side-chain groups, target polymer HTMs (PVCz-ThSMeTPA and PVCz-ThOMeTPA) with high mobility and multisite passivation functions are achieved. The presence of more sulfur atom-containing groups in side-chain endows PVCz-ThSMeTPA with increased intra/intermolecular interaction, appropriate energy level, and enhanced buried interfacial interactions with quasi-2D RP perovskite. The hole mobility of PVCz-ThSMeTPA is up to 9.20×10-4 cm2 V-1 S-1. Furthermore, PVCz-ThSMeTPA as multifunctional polymer HTM with multiple chemical anchor sites for buried-interface engineering of quasi-2D PSCs can enable effective charge extraction, defects passivation, and perovskite crystallization modulation. Eventually, the PVCz-ThSMeTPA-based inverted quasi-2D PSC achieves a champion power conversion efficiency of 22.37%, which represents one of the highest power conversion efficiencies reported to date for quasi-2D RP PSCs.

Halogen-Bonded Hole-Transport Material Enhances Open-Circuit Voltage of Inverted Perovskite Solar Cells.

Interfacial properties of a hole-transport material (HTM) and a perovskite layer are of high importance, which can influence the interfacial charge transfer dynamics as well as the growth of perovskite bulk crystals particularly in inverted structure. The halogen bonding (XB) has been recognized as a powerful functional group to be integrated with new small molecule HTMs. Herein, a carbazole-based halo (iodine)-functional HTM (O1), is synthesized for the first time, demonstrating a high hole mobility and suitable energy levels that align well with those of perovskites. The strong interaction between O1 and perovskite, i.e., I···I-, induces the formation of an ordered interlayer, which are verified by both theoretical and experimental studies. Compared to the reference HTM (O2) without any halo-function, the XB-induced interlayer effectively enhances the interfacial charge extraction efficiency, while significantly hindering the non-radiative charge recombination by reducing the surface traps upon the strong passivation effect. This is reflected as a big increase in the open-circuit voltage by up to 114mV in the fabrication of inverted devices with the highest power conversion efficiency of 22.34%. Moreover, the ordered XB-driven interlayer at the interface of O1 and perovskite is mainly responsible for the extended lifespan under the operational conditions.

Charge Carrier Dynamics of SnO2 Electron‐Transporting Layers in Perovskite Solar Cells

Perovskite solar cells (PSCs) have demonstrated remarkable increase in their photovoltaic efficiencies over the past several years. Charge carrier properties including charge selectivity, extraction, and transport play key roles in device performances. Therefore, a comprehensive insight into the charge carrier dynamics and mobility within the bulk materials and at the interface is of great importance for the future development of this cutting‐edge technology. This review discusses the recent advances that have been made in SnO2 electron‐transporting layers and their limitations, followed by outlining the key development of novel strategies in improving SnO2 films through surface defect engineering, interface modification, and doping approaches. In addition, the recent developments are highlighted for identifying the origin of defect and trap center, and promoting SnO2 electron extraction and transporting capacity in PSCs. Importantly, the novel approaches are also discussed for studying photogenerated charge carrier dynamics of the devices. In conclusion, the own prospectives and outlooks are presented for the development of SnO2‐based PSCs, with a particular focus on addressing current difficulties in SnO2 and providing in‐depth understanding on the relationships between materials and devices.

Reducing Interfacial Recombination in Inverted Perovskite Solar Cells With Selenophene-Substituted PCBM: Comparison With Thiophene and Furan Substitution.

Reducing the interfacial recombination and improving the charge transfer capability of charge transport layers are effective strategies to enhance the efficiency and stability of perovskite solar cells (PSCs). This study evaluates, for the first time, the effects of selenophene substitution in the chemical structure of phenyl-butyric acid methyl ester (PCBM) on the performance and stability of inverted PSCs. Selenophene substitution was compared to thiophene and furan substitutions, and the reference PCBM without chalcogenophene moiety. Additionally, this study investigates the differences between using the fullerene cages C70 and C60 in the PCBM chemical structure. The photovoltaic results demonstrate that, with an adequate control of the thickness of the electron transport layer (ETL), incorporating the selenophene moiety in the structures of fullerenes enhances the photovoltaic parameters of PSCs. This improvement results from the reduction in trap-assisted recombination, an increase in electron mobility, and the improved charge extraction processes. The use of C70, as opposed to C60, allows for the preparation of a series of ETLs with comparable thicknesses, although slightly lower efficiencies. This feature facilitates a systematic comparative analysis focused on variations in the electron properties of ETLs, thereby avoiding the inclusion of issues related to thickness and charge recombination processes.

Homogenized contact in all-perovskite tandems using tailored 2D perovskite.

The fabrication of scalable all-perovskite tandem solar cells is considered an attractive route to commercialize perovskite photovoltaic modules1. However, The certified efficiency of 1-cm2 scale all-perovskite tandem solar cells lags behind their small-area (~0.1 cm2) counterparts2,3. This performance deficit originates from inhomogeneity in wide-bandgap (WBG) perovskite solar cells (PSCs) at a large scale. The inhomogeneity is known to be introduced at the bottom interface and within the perovskite bulk itself4,5. Here we uncover another crucial source for the inhomogeneity - the top interface formed during the deposition of the electron transport layer (ETL, C60). Meanwhile, the poor ETL interface is also a significant limitation of device performance. We address this issue by introducing a mixture of 4-fluorophenethylamine (F-PEA) and 4-trifluoromethyl-phenylammonium (CF3-PA) to create a tailored two-dimensional perovskite layer (TTDL), in which F-PEA forms a two-dimensional perovskite at the surface reducing contact losses and inhomogeneity, CF3-PA enhances charge extraction and transport. As a result, we demonstrate a high open-circuit voltage of 1.35 V and an efficiency of 20.5% in 1.77-eV WBG PSCs at a square centimeter scale. By stacking with a narrow-bandgap perovskite sub-cell, we report 1.05 cm2 all-perovskite tandem cells delivering 28.5% (certified 28.2%) efficiency, the highest among all reported so far. Our work showcases the importance of treating the top perovskite/ETL contact for upscaling perovskite solar cells.

Glycolic acid doped PFN-Br as cathode interface to achieve high-efficiency in organic solar cells

Small compounds are often utilized to adjust the cathode interface of organic solar cells (OSCs) due to their low batch change, easy synthesis, unambiguous chemical structure, and low cost. In this work, the alcohol-soluble small molecule material Glycolic acid was doped into the electron transport material Poly(9, 9-bis(3′-(N, N-dimethyl)-N-ethylammoniumpropyl-2, 7-fluorene)-alt-2, 7-(9, 9-dioctylfluorene)) dibromide (PFN-Br) to modify the performance of the cathode interface layer (CIL). The CIL doped with Glycolic acid has better surface morphology, which is conducive to charge transport and extraction. In addition, the introduction of Glycolic acid improves the hydrophilicity of CIL, makes the metal electrode have good contact with CIL, and helps to improve the stability of the OSCs. Additionally, it suppresses the device's trap-assisted recombination and bimolecular recombination, hastening exciton dissociation and charge collection. As a result, the power conversion efficiency (PCE) of OSCs based on PM6: Y6 blend film has risen from 15.26 % to 15.91 %. After 312 hours of stability testing, the aforementioned doped devices still have device performance higher than standard device. Furthermore, based on PBDB-T: IT-M mix film, the PCE of the doped device and reference device was 11.29 % and 10.55 %, respectively. This study suggests that using the alcohol-soluble small-molecule material Glycolic acid can increase the organic solar cells' (OSCs') efficiency. This study provides a new method for manufacturing high-performance OSCs.

Analysis of the Problems of the Research and Modernization of Emission Units of Analytical Devices of Vacuum Electronics

In various electron-optical and ion-beam devices and vacuum electronics installations, emission elements and units are used to extract and form beams of charged particles. Their focusing properties significantly affect the quality parameters and technical characteristics of the analytical devices and technological installations in which they are used. Due to the specificity of the initial conditions during the formation of the beams of charged particles in the area of charged particle extraction, the methods of studying single and conventional immersion electron lenses are not suitable for the high quality theoretical and numerical studies of the properties of immersion objectives. In this paper, theoretical and numerical studies were conducted on the problems in analyzing the focusing parameters of charged particles in emission elements and units when solving problems of designing and upgrading devices and installations of vacuum electronics. As a result of the studies, a theoretical method for studying cathode lenses with a curved optical axis was developed and options for solving problems in correcting aberrations of emission elements and units were proposed.

Highly Stable and Efficient N‐I‐P Structured Tin‐Rich Lead‐Tin Halide Perovskite Solar Cells with Blended Hole‐Transporting Materials

AbstractMixed lead‐tinv halide (LTH) perovskite solar cells (LTH‐PSCs) can reduce the toxicity concerns of full lead‐based PSCs and potentially optimize the bandgap to maximize efficiency. However, commonly used hole‐transporting material (HTM) 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenyl‐amine)9,9′‐spirobifluorene (Spiro‐OMeTAD) with additional dopants Li‐bis(trifluoromethanesulfonyl) imide (Li‐TFSI) and 4‐tert‐butylpyridine (t‐BP) deteriorate oxidation Sn2+ to Sn4+ leading to trap formation. Here, the study introduces a novelty Sn‐friendly HTM for Sn‐rich LTH‐PSCs, combining Spiro‐OMeTAD with 4‐Isopropyl‐4′‐methyldiphenyliodonium tetrakis(pentafluorophenyl)borate (dpi‐TPFB) as a dopant and blended with poly(3‐hexylthiophene‐2,3‐diyl) (P3HT). This blended HTM avoids the harmful effects of Li‐TFSI and t‐BP dopants and leverages the beneficial hydrophobic properties of P3HT, which predominantly resides on the surface with a face‐on orientation. This arrangement not only enhances charge transport and extraction but also improves device stability by protecting the perovskite from environmental factors. Optimizing the P3HT concentration of blended HTM achieved a PCE of 17.27%, the highest reported for n‐i‐p structured Sn‐rich mixed LTH‐PSCs. This HTM also significantly improved device stability, maintaining over 90% of the initial PCE after 3000 h of storage and 80% under maximum power point tracking (MPPT) for 550 h in the air.

Mechanical and Ionic Characterization for Organic Semiconductor-Incorporated Perovskites for Stable 2D/3D Heterostructure Perovskite Solar Cells.

Hybrid metal halide perovskite (MHP) materials, while being promising for photovoltaic technology, also encounter challenges related to material stability. Combining 2D MHPs with 3D MHPs offers a viable solution, yet there is a gap in the understanding of the stability among various 2D materials. The mechanical, ionic, and environmental stability of various 2D MHP ligands are reported, and an improvement with the use of a quater-thiophene-based organic cation (4TmI) that forms an organic-semiconductor incorporated MHP structure is demonstrated. It is shown that the best balance of mechanical robustness, environmental stability, ion activation energy, and reduced mobile ion concentration under accelerated aging is achieved with the usage of 4TmI. It is believed that by addressing mechanical and ion-based degradation modes using this built-in barrier concept with a material system that also shows improvements in charge extraction and device performance, MHP solar devices can be designed for both reliability and efficiency.

Mesoporous structured MoS2 as an electron transport layer for efficient and stable perovskite solar cells.

Mesoporous structured electron transport layers (ETLs) in perovskite solar cells (PSCs) have an increased surface contact with the perovskite layer, enabling effective charge separation and extraction, and high-efficiency devices. However, the most widely used ETL material in PSCs, TiO2, requires a sintering temperature of more than 500 °C and undergoes photocatalytic reaction under incident illumination that limits operational stability. Recent efforts have focused on finding alternative ETL materials, such as SnO2. Here we propose mesoporous MoS2 as an efficient and stable ETL material. The MoS2 interlayer increases the surface contact area with the adjacent perovskite layer, improving charge transfer dynamics between the two layers. In addition, the matching between the MoS2 and the perovskite lattices facilitates preferential growth of perovskite crystals with low residual strain, compared with TiO2. Using mesoporous structured MoS2 as ETL, we obtain PSCs with 25.7% (0.08 cm2, certified 25.4%) and 22.4% (1.00 cm2) efficiencies. Under continuous illumination, our cell remains stable for more than 2,000 h, demonstrating improved photostability with respect to TiO2.

Silver Telluride Colloidal Quantum Dot Solid for Fast Extended Shortwave Infrared Photodetector.

Extended shortwave infrared (eSWIR) photodetectors that employ solution-processable semiconductors have attracted attention for use in applications such as ranging, night vision, and gas detection. Colloidal quantum dots (CQDs) are promising materials with facile bandgap tunability across the visible-to-mid-infrared wavelengths. However, toxic elements, such as Hg and Pb, and the slow response time of CQD-based IR photodetectors, limit their commercial viability. This article presents a novel eSWIR photodetector that is fabricated using silver telluride (Ag2Te) CQDs. Effective thiolate ligand exchange enables a lower trap density and improved carrier mobility in CQD solids. Furthermore, a vertical p-n photodiode architecture with a favorable energy-level landscape is utilized to facilitate charge extraction, resulting in a fast, room-temperature-operable, and toxic-element-free CQD photodetector. The best eSWIR Ag2Te CQD photodetector exhibits a fall time of 72ns, representing the fastest response time among all prior CQD-based eSWIR photodetectors, including those containing toxic elements, such as Pb and Hg.

Engineering Spacer Conjugation for Efficient and Stable 2D/3D Perovskite Solar Cells and Modules

Incorporating 2D perovskite in 3D perovskite absorber holds great potential to improve the stability and efficiency of perovskite solar cells (PSCs). However, the bulky‐cation‐based 2D structures often exhibit poor charge transport and are prone to formation of charge‐extraction barrier that impedes efficient device operation. We address these issues by introducing aromatic spacers with enhanced molecular conjugation. Among our tested aromatic spacers, the pyrenylbutanamine (PyBA) spacer was shown to endow 2D perovskites with superior charge transport properties and efficient charge extraction from the bulk perovskite in 2D/3D PSCs, due to the highest degree of conjugation. As a result, we achieved a power conversion efficiency of up to 25.3% in a 0.16‐cm2 single cell and 21.0% in a 24.8‐cm2 module. Moreover, the incorporated PyBA substantially raised the resistance of 2D/3D PSCs against moisture and ion migration, resulting in enhanced environmental, thermal, and operational stability. Notably, the PyBA‐based devices retained over 90% of their initial efficiency after 2000 hours at 25 ℃ and 80% relative humidity, or 1000 hours at 85 ℃ and 85% humidity, or 3000 hours of operation under continuous 1‐Sun illumination at 40 ℃, showcasing their enhanced stability compared to previously reported 2D/3D PSCs.

Mitigating interfacial recombination enabling efficient semitransparent organic photovoltaics

Charge recombination at the interface between top electrode and active layer is a substantial current loss pathway in semitransparent organic photovoltaics (STOPVs). Reducing interfacial traps is an effective strategy to mitigate interfacial recombination and promote charge extraction, and thereby improve the power conversion efficiencies (PCEs). Herein, a facile approach of depositing 11-mercapto-undecanoic acid (11-MUA) on zinc oxide (ZnO) cathode interlayer in conventional STOPVs is demonstrated. 11-MUA can form covalent interactions with both ZnO and silver (Ag) and thus can induce the formation of high-quality ultrathin Ag electrode. Compared with that deposited on bare ZnO, the Ag electrode on ZnO/11-MUA shows higher conductivity as well as higher optical transparency. The STOPVs based on ZnO/11-MUA/Ag exhibit 2 orders of magnitude lower surface trap density than the counterparts based on ZnO/Ag. Consequently, 11-MUA simultaneously improves the PCEs from 11.2% to 12.1% and average visible transmittance from 21.6% to 27.0% in the STOPVs. Furthermore, arising from the 11-MUA-modified interface, the thermal stability of STOPVs based on ZnO/11-MUA/Ag is also improved.

Engineering Spacer Conjugation for Efficient and Stable 2D/3D Perovskite Solar Cells and Modules.

Incorporating 2D perovskite in 3D perovskite absorber holds great potential to improve the stability and efficiency of perovskite solar cells (PSCs). However, the bulky-cation-based 2D structures often exhibit poor charge transport and are prone to formation of charge-extraction barrier that impedes efficient device operation. We address these issues by introducing aromatic spacers with enhanced molecular conjugation. Among our tested aromatic spacers, the pyrenylbutanamine (PyBA) spacer was shown to endow 2D perovskites with superior charge transport properties and efficient charge extraction from the bulk perovskite in 2D/3D PSCs, due to the highest degree of conjugation. As a result, we achieved a power conversion efficiency of up to 25.3% in a 0.16-cm2 single cell and 21.0% in a 24.8-cm2 module. Moreover, the incorporated PyBA substantially raised the resistance of 2D/3D PSCs against moisture and ion migration, resulting in enhanced environmental, thermal, and operational stability. Notably, the PyBA-based devices retained over 90% of their initial efficiency after 2000 hours at 25 ℃ and 80% relative humidity, or 1000 hours at 85 ℃ and 85% humidity, or 3000 hours of operation under continuous 1-Sun illumination at 40 ℃, showcasing their enhanced stability compared to previously reported 2D/3D PSCs.

Ethanol processable inorganic-organic hybrid hole transporting layers enabled 20.12% efficiency organic solar cells.

In this study, a high-performance inorganic-organic hybrid hole transporting layer (HTL) was developed using ethanol-soluble alkoxide precursors and a self-assembled monolayer (SAM). Three metal oxides-vanadium oxide (VOx), niobium oxide (Nb2O5), and tantalum oxide (Ta2O5)-were synthesized through successive low-temperature (100 °C) thermal annealing (TA) and UV-ozone (UVO) treatments of their respective precursors: vanadium oxytriethoxide (EtO-V), niobium ethoxide (EtO-Nb), and tantalum ethoxide (EtO-Ta). Among these, the Nb2O5 film exhibited excellent transmittance, a high work function, and good conductivity, along with a more compact and uniform structure featuring fewer interfacial defects, which facilitated efficient charge extraction and transport. Furthermore, the deposition of a SAM of (2-(9H-carbazol-9-yl)ethyl)phosphonic acid (2PACz) on top of Nb2O5 further passivated defects, enhancing interfacial contact with the photoactive layer. The resulting inorganic-organic hybrid HTL of Nb2O5/2PACz demonstrated excellent compatibility with various photoactive blends, achieving impressive power conversion efficiencies of 19.44%, 19.18%, and 20.12% for the PM6:L8-BO, PM6:BTP-eC9, and D18:BTP-eC9 based organic solar cells, respectively. 20.12% is the best performance for bulk heterojunction organic solar cells with binary components as the photoactive layer.