Pulse Characteristics Research Articles

Formation of CBOC signals with a reduced level of out-of-band radiation

Formulation of the problem. The article considers the issues of choosing low-pass filters with finite and infinite pulse characteristics used to generate CBOC signals with phase manipulation with a reduced level of out-of-band radiation. Purpose. The influence of the filter frequency band on the distortion of CBOC signals in the frequency and time domain is estimated by mathematical modeling. Results. The following filter parameters, peak factor and ACPR (Adjacent Channel Power Ratio) were studied and calculated. Practical significance. The results obtained can be used by developers of local navigation systems.

Centimeter-level 2D ultra-small interdigital sensor for ESD detection of spacecraft

The spacecraft in geosynchronous orbit interacts with the space plasma environment, which is prone to electrostatic discharge and affects the safe operation of the spacecraft. In order to realize simple, accurate and reliable electrostatic discharge detection in space environment, based on the energy spectrum characteristics of spacecraft electrostatic discharge electromagnetic radiation electromagnetic pulse and the electromagnetic pulse sensing principle of interdigital electrode, a centimeter-level two-dimensional planar ultra-small interdigital sensor with a size of only 4 cm × 3 cm × 0.01 cm is developed. The impedance matching circuit is established to greatly improve the transmission efficiency of electromagnetic pulse, which is 59.34 % higher than that before the matching circuit is added. Finally, a spacecraft vacuum electrostatic discharge simulation experiment platform is built to test the frequency response characteristics of the sensor. The results show that the frequency response characteristics of the electromagnetic pulse signal perceived by the sensor developed in this paper are consistent with the main frequency characteristics of the spacecraft electrostatic discharge radiation electromagnetic pulse energy spectrum, which can be used for spacecraft electrostatic discharge detection in space environment.

Space–time characterization of ultrashort laser pulses: A perspective

The characterization of ultrashort laser pulses has significantly advanced beyond the standard spatial and temporal diagnostics to now include sophisticated spatio-temporal measurement techniques. In this perspective, we provide an overview of the current state of space–time characterization, discussing the theoretical foundations of ultrashort laser pulses, the various measurement techniques and their design trade-offs, and the challenges and opportunities for future development. We explore the extension of these techniques to different wavelength regimes and delve into the unique challenges posed by the characterization of polarization-structured beams. The potential for data-driven analysis to enhance the information extracted from the measurements is highlighted, along with the need for direct measurement of previously inaccessible field components, such as the longitudinal electric field in tightly focused beams. As these diagnostic tools continue to evolve, we anticipate a future where the intricate space–time structure of light can be analyzed on a routine basis, opening up new frontiers in ultrafast science and technology.

SYSTEM FOR DETERMINING THE TECHNICAL CONDITION OF AN INTERNAL COMBUSTION ENGINE BASED ON MEASUREMENT AND ANALYSIS OF VIBRATION

The relevance of the topic of this study is due to the need to ensure reliable operation of vehicles and minimize the risks of interruptions in the operation of internal combustion engines (ICE). A common phenomenon in operation is misfiring, which negatively affects the efficiency of the ICE and can lead to emergencies that entail significant financial and temporary losses for commercial companies. The problem is the need to identify and prevent such malfunctions early. The purpose of the study is to develop and test a system for monitoring and analyzing the technical condition of the internal combustion engine through vibration measurements. Method and methodology. The work used the method of in-place diagnostics, the use of which increases efficiency of determining the technical condition of the vehicle internal combustion engine. Results. This article describes the system developed by the authors for checking the technical condition of an internal combustion engine. As a result, software to process and record vibration and timing data has been developed in MATLAB. The study of influence of defects in mechanisms and systems of internal combustion engine on uniformity of time-amplitude characteristic of vibration pulses of each individual cylinder, which occur during operation of internal combustion engine, was carried out by calculation and experimentation. As a key conclusion, it is noted that the developed system allows to quickly and non-invasively identify the idle cylinder or the one of which contribution to the rotational movement of the crankshaft is the least compared to others. The research makes it possible to provide diagnostics in a short time using available means. Scope of application of the results. the research results were tested in the conditions of a service company when diagnosing the internal combustion engines of passenger cars and trucks, and can be applied by both car repair shops and car enthusiasts.

Terahertz control and timing correlations in a transmission electron microscope.

Ultrafast electron microscopy provides a movie-like access to structural dynamics of materials in space and time, but fundamental atomic motions or electron dynamics are, so far, too quick to be resolved. Here, we report the all-optical control, compression, and characterization of electron pulses in a transmission electron microscope by the single optical cycles of laser-generated terahertz light. This concept provides isolated electron pulses and merges the spatial resolution of a transmission electron microscope with the temporal resolution that is offered by a single cycle of laser light. We also report the all-optical control of multi-electron states and find a substantial two-electron and three-electron anticorrelation in the time domain. These results open up the possibility to visualize atomic and electronic motions together with their quantum correlations on fundamental dimensions in space and time.

Unraveling Dry Jigging: Insights into Pulsation, Energy Consumption, and Stratification Dynamics

The increasing concerns regarding water usage in mineral processing have led to a growing interest in dry jigging in recent years. However, there is still a need for a more comprehensive examination of the operational aspects of the technique. In this sense, this study focused on three main elements: (a) examining the air pulse pattern during dry jig operation; (b) assessing the evolution of the stratification profile over time using partition analysis; and (c) evaluating the specific energy consumption of batch dry jigging during operation. Also, an innovative operational strategy known as “transient pulsing” was proposed and analyzed, involving varying the intensity and frequency of the air pulse throughout the stratification process. All tests were conducted using density tracers spread across 11 density ranges (0.4–2.4 g/cm3) and a base bed (gravel) to analyze their separation in a batch, pilot-scale dry jig. Pressure drop and active power data were collected to measure the pulse characteristics and energy consumption. The airflow curves, obtained through pressure drop data, indicated that the pulsation process is more unstable as the airflow increases, possibly due to the pressure fluctuations experienced by air during valve closure. For the pulsation conditions used in the tests, the specific energy consumption was 10.66 Wh/kg of jigged material, with most of it related to the blower drive system. Analysis of the stratification evolution over time showed an oscillatory behavior, alternating between states of better (Ep < 0.1) and worse (Ep > 0.1) separation, especially for the near-gravity material (NGM). Results of the transient pulsation tests suggested that progressively increasing the vertical displacement of the bed during stratification resulted in slightly better segregation levels and more stable jigging evolution over time in comparison to stationary pulse conditions.

Temporal Characterization of Laser Pulses Using an Air‐Based Knife‐Edge Technique

Temporal Characterization of Laser Pulses Using an Air‐Based Knife‐Edge Technique

Single-shot measurement of a laser waveform using plasma fluorescence in ambient air.

The temporal characterization of a laser pulse is an important task in studying ultrafast laser-matter interactions. It is ideal to measure the temporal profile of the laser pulse with a single laser shot when the repetition rate is low or its interaction with matter is unstable. Here we report a new approach for the single-shot temporal characterization of a laser pulse, based on the TIPTOE (tunneling ionization with a perturbation of the time-domain observation of an electric field) method. The waveform of the laser pulse is reconstructed from the intensity modulation of plasma fluorescence emission. The result of the single-shot measurement is compared with the time-delay scanning TIPTOE measurements, supporting the validity of the single-shot measurement.

Field-resolved space–time characterization of few-cycle structured light pulses

Accompanied by the rapid development of ultrafast laser platforms in recent decades, the spatiotemporal manipulation of ultrashort laser pulses has attracted much attention due to the potential for cutting-edge applications of structured light, including optical tweezers, optical communications, super-resolution imaging, time-resolved spectroscopy in molecules and quantum materials, and strong-field physics. Today, techniques capable of characterizing the full spatial, temporal, and polarization state properties of structured light are strongly desired. Here, we demonstrate a technique, termed 3D TIPTOE, for characterizing structured mid-infrared waveforms, which uses only a two-dimensional silicon-based image sensor as both the detector and the nonlinear medium. By combining the advantages of the sub-cycle time resolution afforded by nonlinear excitation and the spatial resolution inherent to the two-dimensional sensor, the 3D TIPTOE technique allows full characterization of structured electric fields, significantly reducing the complexity of detection compared to other techniques. The validity of the technique is established by measuring both few-cycle Bessel–Gaussian pulses and radially polarized femtosecond vector beams.

Quantitative failure analysis of lithium-ion batteries based on direct current internal resistance decomposition model

Accurate failure analysis plays a pivotal role in the optimization design and lifetime prediction of 4.45 V high-voltage LiCoO2/Graphite (LCO/Gr) batteries. Multiphysics coupling model brings great opportunities to conduct battery failure analysis quantitatively, although it is quite challenging because many model parameters need to be handled properly. Herein, we systematically elaborate the differences of ion and electron transport properties before and after cycling ageing of LCO/Gr batteries by constructing direct current internal resistance (DCR) decomposition model. The key parameters acquisition method is established, and the mechanism of DCR growth is elucidated. Furthermore, the aforementioned model parameters are refined by using a hybrid power pulse characteristics (HPPC) curve optimization algorithm based on DCR decomposition results obtained from the three-electrode battery system. Through analyzing the influence of single-factor parameter ageing on battery voltage output capacity and discharge temperature rise, the main factors affecting battery failure process are identified. For instance, the account of the positive electrochemical reaction resistance related to the kpos increased from the initial 22.9% of total DCR to 37.3% after ageing. This work provides a reliable quantitative analysis basis for the global optimization design of advanced LIBs.

A Bias‐Dependent Weight Update Characteristics of Low Power Synaptic Pass‐Transistors with a Hf‐Doped ZnO Channel Layer

AbstractA study on a bias voltage‐dependent weight update characteristics in a sub‐threshold region of a low power synaptic pass‐transistor (SPT) is presented with a Hf‐doped zinc oxide active layer. The SPT is a synaptic thin‐film transistor (TFT) in series with a load TFT which is used as a resistive load (RL) to be scaled by a bias voltage (VB). Here, when the VB of the load TFT is modulated, the RL can be changed. With the changed RL, it is expected that the weight update characteristics (i.e., dynamic ratio) and electrical characteristics (i.e., power consumption) of the SPT are varied, respectively, suggesting a trade‐off relation between the dynamic ratio and power consumption. To check these, the pulsed characteristics of the fabricated SPT is monitored for different VB, respectively. From experimental results, as increasing VB, it is found that the decreased RL leads to the increase of the power consumption while enhancing the dynamic ratio because a full depression (FD) can be relatively easy. On the other hand, when the VB is reduced, the RL is increased resulting in the decrease of both the power dissipation and the dynamic ratio due to a difficulty of FD.

Buildup of different emission regimes in a nonlinear polarization rotation modelocked all-fiber laser

We investigated experimentally and theoretically the buildup of light pulses in an erbium-doped sub-MHz all-fiber laser modelocked by nonlinear polarization rotation. We were able to study the buildup of two different emission regimes: standard solitons and noise-like pulses. In each case, we were able to determine the round-trips required to achieve a stable emission state. Temporal traces and optical spectra of single pulses were measured along the start-up transient of the laser. The experimental results were also confirmed by numerical simulations. Under the specific conditions of this laser, the soliton regime takes about 400 round-trips to reach single-pulse emission. In the noise-like pulse regime, it takes only 20 round-trips for the characteristics of noise-like pulses to show up; although a more steady-state emission is reached also at about 400 round-trips.

Effect of Saturable Absorber Length on Characteristics of Dual Laser Pulses of Passive Q-Switched

Effect of Saturable Absorber Length on Characteristics of Dual Laser Pulses of Passive Q-Switched

An experimental study of intensity‐phase characterization of femtosecond laser pulses propagated through a polymethyl methacrylate

AbstractThis article presents a comprehensive investigation into the intensity‐phase characteristics of ultrashort laser pulses propagated through a 10 mm thick polymethyl methacrylate (PMMA) using frequency‐resolved optical gating (FROG) and cross‐correlation frequency‐resolved optical gating (XFROG) techniques. The study focuses on discerning characteristic changes that are induced by the PMMA on the laser pulse. The results reveal that the phase variations exhibit a consistent trend and pattern. At the same time, the temporal full width at half maximum (FWHM) of both FROG and XFROG measurements displays only minor changes. The overall analysis indicates that PMMA induces no discernible modifications in the pulse, thus positioning it as a viable optical element. The analysis of reference FROG, FROG, and XFROG with PMMA is compared and discussed, showing that this analysis provides a foundation for optimizing PMMA's utilization in the optical components of ultrafast laser systems. This experimental study strongly affirms that PMMA could be a potential candidate as an optical element for laser pulses.

Spatial Characterization of Multiple Pulses, With Different Spatial Profiles, From a Single Camera Snapshot

Spatial Characterization of Multiple Pulses, With Different Spatial Profiles, From a Single Camera Snapshot

Pulse Radiation Characteristics Prediction Method of Vivaldi Antenna based on Dipole Array

This paper presents a theoretical method to estimate the pulse radiation characteristics of Vivaldi antennas. Based on the surface current distribution and the ultra-wideband radiation principle, Vivaldi antenna is equivalently modeled as a dipole array, and the pulse radiation characteristics of a single Vivaldi antenna are brought out utilizing the spatial superposition approach. Then, the influences and results of the Vivaldi antenna pulse characteristics prediction with different construction ways of the dipole array and element numbers are furthermore investigated. Next, a quadratic spatial superposition technique is employed to complete the theoretical prediction for time-domain radiation characteristics of Vivaldi antenna arrays. Experiments and simulations are conducted separately to verify the proposed method for both single Vivaldi antenna and array. The validated results demonstrate that the dipole array-based theoretical prediction method can effectively capture the pulse radiation characteristics for both individual Vivaldi antenna and array operating in different modes, thereby addressing challenges associated with estimating radiation characteristics in ultra-wideband pulse applications.

Phase-matched third-harmonic generation in silicon nitride waveguides.

Third-harmonic generation (THG) in silicon nitride waveguides is an ideal source of coherent visible light, suited for ultrafast pulse characterization, telecom signal monitoring and self-referenced comb generation due to its relatively large nonlinear susceptibility and CMOS compatibility. We demonstrate third-harmonic generation in silicon nitride waveguides where a fundamental transverse mode at 1,596 nm is phase-matched to a TM02 mode at 532 nm, confirmed by the far-field image. We experimentally measure the waveguide width-dependent phase-matched wavelength with a peak-power-normalized conversion efficiency of 5.78 × 10-7 %/W2 over a 660-μm-long interaction length.

The impact of clinical audits on patient radiation exposure for device procedures

Abstract Background Clinical audits aim to ensure ideal use of ionizing radiation in clinical practice. Since it became mandatory by Swiss law in 2018, such an audit also took place in our Cardiac Pacing and Electrophysiology Division at the University Heart Center. Purpose To establish local diagnostic reference levels (DRLs) for specific procedures and to examine if patient radiation exposure was reduced after the clinical audit. Methods Retrospective cohort study including patients from October 2018 to October 2020 who underwent device implantation, including pacemakers, implantable cardioverter defibrillators (ICD), cardiac resynchronization therapy (CRT), or lead extraction / device explantation. Main measures to reduce radiation exposure after the audit were lower pulsed fluoroscopy frame rates and dose characteristics at baseline. Patient radiation exposure was evaluated with the dose-area product (DAP), cumulative dose, fluoroscopy time, and the number of cine acquisitions. Secondary endpoints included the effective dose, the acute procedural success rate and 30-day complications. Data were collected from a dose management system and cross-checked for accuracy with the patient information system. The third quartiles were set as local DRLs. Data before and after the clinical audit were compared. Results A total of 541 patients (45.7 % before the audit, 54.3% after the audit) were included. 28.3% had a conventional pacemaker, 22.0% a leadless pacemaker, 21.1% an ICD, and 17.2% a CRT implantation. Lead extraction / device explantation was undergone by 11.5% of patients. The local DRLs (including all procedures before and after the audit) for the DAP were significantly lower as compared to national DRLs (6.2 dGy.cm2 versus 300 dGy.cm2 for conventional pacemakers; 7.6 dGy.cm2 versus 200 dGy.cm2 for ICDs, 203 dGy.cm2 versus 570 dGy.cm2 for CRTs). After the audit, DAP (Figure 1), cumulative dose, effective dose and the number of cine acquisition significantly decreased for conventional pacemakers (p-value ≤ 0.04), whereas no significant differences were observed for the other procedures. The acute procedural success rate (98.4 vs 98.9%) and the 30-day complications (4.0 vs 7.8%) were not significantly different before and after the audit. Conclusions The clinical audit in our institution led to a significant reduction of radiation exposure for patients during pacemaker implantations. Regarding DRLs, local values were far below national DRLs, which suggests that national DRLs need to be updated more regularly. Our study highlights the importance of clinical audits and the need for more research in this field.

Machinability and pulse characteristics of Ti-16Al-14Nb (α/β) alloy in wire-electric discharge machining process: A surface integrity study

The goal of the present work is to produce the efficient cutting of Ti-16Al-14Nb (α/β) alloy through wire-electric discharge machining and contemplate the terminologies such as machining ability, surface integrity and material removing capability. For this, the experimentation has been designed by considering three process parameters, pulse-on time ( Ton), pulse-off time ( Toff) and peak current ( Ip) at three significant levels (low, high, intermediate) in L27 order designed from design of experiments. The effect of these process variables on pulse characteristics, surface roughness ( Ra), kerfwidth ( Kw) and material removal rate ( MRR) is analyzed and mathematically modeled with analysis of variance. The results state that the highest MRR (0.521, 0.51, 0.506 mm3/sec) and low surface roughness (8.91, 8.89, 8.68 µm) values are observed at the highest level (110 µs, 15 µs, 8 A). If the pulse duration is kept at low ( Ton = 40µs, Toff = 3µs), the increase in peak current from 3 A to 8 A leads to a 64.54% increase in MRR and a 52.9% increase in Ra values. ANOVA results stated that Ton has contributed 20.4%, 35.8% and 19.3%, and Ip has contributed 43.1%, 30.5% and 46.6% influence on MRR, Kw and Ra respectively. The voltage–current characteristics studies confirmed that the strong intense pulses at a higher peak current (8 A) resulted in the increased MRR (0.521 mm3/sec) and Ra (8.43 µm) leading to the formation of swages and ridges. The surface integrity analysis derived from Abbott–Firestone curve agreed that the lowest level has shown better skewness ( Rsk = −0.274) and at highest level showed a larger deviation in skewness ( Rsk = +2.672) signifies that higher asymmetry (poor) of the surface.

Gain-Switched Er-Doped Fluoride Fiber Laser at ~3.75 μm

We demonstrate a pulsed Er-doped ZBLAN fiber laser operating at 3.75 μm based on the gain-switching scheme. A diffraction grating is introduced as a wavelength selection component to enable stable lasing in this long-wavelength region that deviates from the emission peak of 4F9/2→4I9/2 transition in Er3+. Different from the conventional gain-switching behavior where the pulse repetition frequency of the output laser is same as the that of the pump, the gain-switched laser demonstrated here shows a variable pulse repetition frequency, which accounts for 1/n (n = 4, 3, 2) of the pump pulse repetition frequency, in response to the 1950 nm pump power. The output pulse characteristics, including average output power, repetition frequency, pulse duration, and peak power, are investigated in detail. Over 200 mW average output power at 3.75 μm was obtained at 12 W of 1950 nm pump power. This work demonstrates that the Er-doped ZBLAN fiber laser, in combination with gain-switched scheme, is a feasible and promising approach to generate powerful pulsed emission > 3.7 μm.