Characteristics Of Thin-film Transistors Research Articles

Low-frequency noise analysis on asymmetric damage and self-recovery behaviors of ZnSnO thin-film transistors under hot carrier stress

The need for understanding the low-frequency noise (LFN) of metal oxide semiconductor thin-film transistors (TFTs) is increasing owing to the substantial effects of LFN in various circuit applications. A focal point of inquiry pertains to the examination of LFN amidst bias stress conditions, known to compromise TFT reliability. In this study, we investigate the effects of hot carrier stress (HCS) on zinc tin oxide (ZTO) TFTs by low-frequency noise (LFN) analysis. Asymmetric damage caused by HCS is analyzed by measuring the power spectral density at the source and drain sides. The excess noise generated by the HCS is analyzed with consideration of trap density of states (DOS). It is revealed that the needle defects are generated during the HCS, significantly affecting the LFN characteristics of the ZTO TFTs. Additionally, we observe a self-recovery behavior in the devices and demonstrate the relevant changes in the LFN characteristics following this phenomenon. This study provides valuable insights into the LFN characteristics of ZTO TFTs under HCS conditions and sheds light on the underlying mechanisms.

Ultrathin In2O3 thin-film transistors deposited from trimethylindium and ozone

Indium oxide (In2O3) is a promising channel material for thin-film transistors (TFTs). In this work, we develop an atomic layer deposition (ALD) process of using trimethylindium and ozone (O3) to deposit In2O3 films and fabricate ultrathin In2O3 TFTs. The In2O3 TFTs with 4 nm channel thickness show generally good switching characteristics with a high I on/I off of 108, a high mobility (μ FE) of 16.2 cm2V−1s−1 and a positive threshold voltage (V th) of 0.48 V. Although the 4 nm In2O3 TFTs exhibit short channel effect, it can be improved by adding an ALD Ga2O3 capping layer to afford the bilayer In2O3/Ga2O3 channel structure. The afforded In2O3/Ga2O3 TFTs exhibit improved immunity to the short channel effect, with good TFT characteristics of I on/I off of 107, μ FE of 9.3 cm2V−1s−1 , and positive V th of 2.23 V. Overall, the thermal budget of the entire process is only 400 °C, which is suitable for the display and CMOS back-end-of-line-compatible applications.

(Invited) Polarization Stability Improvement for Hf0.5Zr0.5O2-Based Ferroelectric Capacitor

The instability in polarization during the endurance test of Hf0.5Zr0.5O2 (HZO) ferroelectrics thin films including the wake-up and the fatigue are still major challenges for the development of HZO-based ferroelectric memories. In this work, we will review the proposed mechanisms of the instabilities in polarization including wake-up and fatigue of the HZO-based metal-ferroelectric-metal (MFM) capacitors. Then, the material processing techniques to address the issues of instabilities are provided. The in-situ deposition of electrode and ferroelectric layers by atomic layer deposition (ALD) attracted considerable attention as a promising solution. Owing to the improved interface quality, both the endurance characteristics and remanent polarization were enhanced. We have also developed a HfO2/ZrO2 superlattice structure to further enhance the ferroelectric endurance of the MFM capacitors. The superlattice MFM capacitors show wake-up free characteristics with excellent endurance. The device performances and endurance characteristics of ferroelectric thin film transistor will also be presented.

Effect of interface defects on electrical characteristics of a-ITGZO TFTs under bottom, top, and dual gatings

Here, we investigate the effects of interface defects on the electrical characteristics of amorphous indium-tin-gallium-zinc oxide (a-ITGZO) thin-film transistors (TFTs) utilizing bottom, top, and dual gatings. The field-effect mobility (27.3 cm2/V∙s) and subthreshold swing (222 mV/decade) under a dual gating is substantially better than those under top (12.6 cm2/V∙s, 301 mV/decade) and bottom (11.1 cm2/V∙s, 487 mV/decade) gatings. For an a-ITGZO TFT, oxygen deficiencies are more prevalent in the bottom-gate dielectric interface than in the top-gate dielectric interface, and they are less prevalent inside the channel layer than at the interfaces, indicating that the presence of oxygen deficiencies significantly affects the field-effect mobility and subthreshold swing. Moreover, the variation in the electrical characteristics due to the positive bias stress is discussed here.

Characteristics of Fully-Depleted Poly-Si Thin Film Transistors Operated in Above-Threshold Region with Low Drain Bias

Transfer and output characteristics of fully-depleted polycrystalline silicon thin film transistors, including both tail and deep acceptor-like trap states in bulk, in the above-threshold region with low drain bias are presented under low or high state density in the situation without or with interface charge, respectively. The characteristics are calculated by a simple surface-potential-based drain current model in the strong inversion region with valid bias condition explained, and 2D-device simulation. The above-threshold region is found to be divided into Regions I and II, with Vsi , indicating the channel beginning to be completely strongly-inverted and large currents, and explication of deviations between the model and simulation in Region I. The large-traps effect on the range of Region I and Vth in the high state density situation is discovered.

Aqueous solution-processed In2O3 TFTs using focused plasma in gas mixtures

Solution-processed indium oxide (In2O3) thin films have been studied widely as active layers for transparent semiconducting devices because of their high charge carrier concentration, low absorbance, simple fabrication methods, and low cost. Several studies on improving the electrical characteristics of thin-film transistors (TFTs) by optimizing and fine-tuning the fabrication process and using various post-deposition treatments have been conducted to take full advantage of these semiconductor films in high-performance electronics. This study examined the effects of a focused plasma (FP) treatment on In2O3 thin films prepared using a simple solution process at 250 °C. The effects of the FP generated from N2 gas and two gas mixtures (N2-H2 and N2-H2-O2) on the electrical performance of the TFTs were analyzed. The FP treatment enhanced the electrical properties of the device, and the specific performance and stability parameters were improved by the treatment conditions. X-ray photoelectron spectroscopy showed that the FP treatment could effectively control the oxygen vacancies and carrier concentration in the solution-processed In2O3 thin films. Therefore, an FP beam is a viable method for optimizing In2O3 TFTs prepared at low temperatures for application in high-performance transparent electronic devices.

A Simple Scan Driver Circuit Suitable for Depletion-Mode Metal-Oxide Thin-Film Transistors in Active-Matrix Displays

Metal-oxide (MOx) thin-film transistors (TFTs) require complex circuit structures to cope with their depletion mode characteristics, making them applicable only to large-area active matrix (AM) displays despite their low manufacturing cost and decent performance. In this paper, we report a simple MOx 10T-2C scan driver circuit that overcomes the depletion mode characteristics using a series-connected two transistor (STT) configuration and clock signals with two kinds of low-voltage levels. The proposed circuit has a wide operating range of TFT characteristics, i.e., −2.8 V ≤ VTH ≤ +3.0 V. Through the measurement results of the manufactured sample, it was confirmed that the performance and area of our circuit are suitable for high-resolution mobile displays.

P‐2: Investigation of high mobility crystalline IGO TFT with top‐gate structure for LCD display application

The present paper reports the study of electrical characteristics and bias temperature stress (BT) stability of crystalline Indium‐Gallium oxide (IGO) dual‐gate thin film transistor (TFT) with top‐gate structure. TFT with normalized Ion over 100εA and PBTS/NBTIS of 0.35/‐2.85V was successfully fabricated. By adjusting oxygen partial pressure (O2%) and substrate temperature, we can control the wet etching rate (WER) of as‐deposited IGO film. After post annealing, crystalline IGO containing In2O3 phase with preferred orientation of (222) has been formed. The TFT characteristics uniformity and BT stability were found to depend on parameters of gate insulator (GI) deposition and pre‐treatment before GI. Based on experimental results, we propose high GI deposition temperature associated with low N2O plasma treatment power as the optimal condition for industrial production of crystalline IGO TFT.

Effects of iodine doping on structural and electrical characteristics of solution-processed indium oxide thin-film transistors and its potential application for iodine sensing

Effects of iodine doping on structural and electrical characteristics of solution-processed indium oxide thin-film transistors and its potential application for iodine sensing

Analysis on charge-retention characteristics of sub-threshold synaptic IGZO thin-film transistors with defective gate oxides

We provide a quantitative analysis on the charge-retention characteristics of sub-threshold operating In–Ga–Zn–O (IGZO) thin-film transistors (TFTs) with a defective gate-oxide for low-power synaptic applications. Here, a defective SiO2 is incorporated as the synaptic gate-oxide in the fabricated IGZO TFTs, where a defect is physically playing the role as an electron trap. With this synaptic TFT, positive programming pulses for the electron trapping are applied to the gate electrode, followed by monitoring the retention characteristics as a function of time. And this set of the programming and retention-monitoring experiments is repeated in several times for accumulating effects of pre-synaptic stimulations. Due to these accumulated stimulations, electrons are expected to be getting occupied within a deeper trap-state with a higher activation energy, which can lead to a longer retention. To verify these phenomena, a stretched exponential function and respective inverse Laplace transform are employed to precisely estimate a retention time and trap activation-energy for transient experimental results.

Low-temperature preparation and characteristics of top-gate thin-film transistors with La-ZTO active layers and polymethylmethacrylate dielectric layers

A top-gate coplanar-structure thin-film transistor (TFT) combining the advantages of both a co-sputtered amorphous La-doped ZnSnO (a-La-ZTO) active layer and solution-based polymethylmethacrylate (PMMA) gate dielectric layer has been prepared under low temperature (100 °C) with low cost for the first time. The results indicate that the PMMA thin film demonstrates anti-reflection properties when it combines with a-La-ZTO layer to form a double-layer film, displaying high transparency to visible light of ∼90.3%. Moreover, it was found that the La target power during the deposition of a-La-ZTO film plays an important role in suppressing the formation of oxygen vacancies and adjusting the carrier concentration of a-La-ZTO active layer, thus impacting a-La-ZTO TFT performance. Overall, the optimum a-La-ZTO TFT with a La target power of 13.9 W, working in an n-channel enhancement mode, possesses a large saturated mobility (>10 cm2 (Vs)−1) and an on/off drain current ratio over 105.

Floating body effect in indium–gallium–zinc–oxide (IGZO) thin-film transistor (TFT)

In this paper, the floating body effect (FBE) in indium-gallium-zinc-oxide (IGZO) thin-film transistor (TFT) and the mechanism of device failure caused by that are reported for the first time. If the toggle AC pulses are applied to the gate and drain simultaneously for the switching operation, the drain current of IGZO TFT increases dramatically and cannot show the on/off switching characteristics. This phenomenon was not reported before, and our study reveals that the main cause is the formation of a conductive path between the source and drain: short failure. It is attributed in part to the donor creation at the drain region during the high voltage (Vhigh) condition and in part to the donor creation at the source region during the falling edge and low voltage (Vlow) conditions. Donor creation is attributed to the peroxide formation in the IGZO layer induced by the electrons under the high lateral field. Because the donor creation features positive charges, it lowers the threshold voltage of IGZO TFT. In detail, during the Vhigh condition, the donor creation is generated by accumulated electrons with a high lateral field at the drain region. On the other hand, the floating electrons remaining at the short falling edge (i.e., FBE of the IGZO TFT) are affected by the high lateral field at the source region during the Vlow condition. As a result, the donor creation is generated at the source region. Therefore, the short failure occurs because the donor creations are generated and expanded to channel from the drain and source region as the AC stress accumulates. In summary, the FBE in IGZO TFT is reported, and its effect on the electrical characteristics of IGZO TFT (i.e., the short failure) is rigorously analyzed for the first time.

Enhancement of electrical characteristics of SnGaO thin-film transistors via argon and oxygen plasma treatment

The impact of Ar or O2 plasma treatment on the electrical characteristics of SnGaO thin film transistors (TFTs) fabricated via solution method was examined. The findings of the study revealed that Ar plasma treatment for an optimal duration enhances the electrical properties of SnGaO TFTs, including the improvement of mobility, subthreshold swing (S·S.), and on-off ratio. This result is considered to be due to the increased concentration of oxygen vacancy as donor in the channel layer. Oxygen plasma treatment has an opposite effect on the change in oxygen vacancy concentration, thereby reducing the off-state current and facilitating the adjustment of threshold voltage. However, excessive Ar or O2 plasma treatment duration led to an increase in deep defect states and a significant “hump" phenomenon in the output characteristic curve.

Impact of Dual-Gate Configuration on the Endurance of Ferroelectric Thin-Film Transistors With Nanosheet Polycrystalline-Silicon Channel Film

This work explores the characteristics of ferroelectric thin-film transistors (FeTFTs) utilizing an asymmetric dual-gate (DG) structure in both single-gate (SG) and DG operation modes. In the transfer characteristics, DG mode exhibits a memory window (MW) of 1.075 V, smaller than SG mode’s MW of 1.402 V, attributed to the back-gate bias effect causing a reduction in the device’s threshold voltage. However, DG mode demonstrates superior endurance characteristics with 106 cycles compared to SG mode’s 105 cycles. Additionally, the increase in erase pulse voltage (VERS) exacerbates the polycrystalline-silicon channel lattice damage of FeTFT, resulting in subthreshold swing (SS) degradation. Nevertheless, the extent of SS degradation from DG mode operation is significantly lower than that of SG mode, contributing to the superior endurance of DG mode. The elevation of program pulse voltage (VPRG) induces imprint and charge-trapping effects in the top-gate ferroelectric dielectric, leading to reduced endurance. Due to the use of SiO2 as the back-gate dielectric in FeTFT, DG mode exhibits lower impacts of charge-trapping effects from the top-gate ferroelectric dielectric layer, resulting in better endurance compared to SG mode. The asymmetric DG structure provides greater tolerance in the selection of VPRG and VERS.

Output breakdown characteristics of amorphous InGaZnO thin-film transistors at high gate voltage

Output characteristics of top-gate amorphous InGaZnO thin-film transistors are investigated at high gate voltage. With the increasing drain voltage, an output breakdown crops up closely following a drastic uprush of drain current. Such dramatically elevated drain current derives from the self-heating (SH) effect-generated channel donors. Measured at different high gate voltages, the output breakdown occurs in either linear or saturation regime, respectively, corresponding to normally-on and normally-off transfer curve, while the SH-triggering powers are almost identical. The conductor-like channel originates from the SH-induced high donor population, while the disconnection between channel and drain is caused by a highly defective region near drain, where the hot-carrier damage is violently activated by the SH-induced high temperature and the high drain electric field in saturation regime.

Modulating Electrical Characteristics of ZnO Thin-Film Transistors by Scaling Down Gate Dielectric Thickness

Modulating Electrical Characteristics of ZnO Thin-Film Transistors by Scaling Down Gate Dielectric Thickness

Correlation Between Quantum Confinement Effect and Characteristics of Thin-Film Transistors in Solution-Processed Oxide-Based Thin-Films

Correlation Between Quantum Confinement Effect and Characteristics of Thin-Film Transistors in Solution-Processed Oxide-Based Thin-Films

Exploration of structural influences on the ferroelectric switching characteristics of ferroelectric thin-film transistors.

In this paper, quantitative analysis was performed focusing on the structural effect on the ferroelectric switching of ferroelectric thin-film transistors (FeTFTs). FeTFTs and ferroelectric capacitor (FeCap) test element groups (TEGs) were designed and fabricated, and positive-up-negative-down (PUND) measurements were performed to analyze the switching characteristics of ferroelectric films in various structures constituting an FeTFT. It was verified that TiN/HZO/a-IGZO/Mo (MFSM, FeTFT source/drain contact) mostly contributed to the memory operation of an FeTFT, while TiN/HZO/a-IGZO (MFS, FeTFT channel) exhibits one-time memory operation with irreversible polarization switching. In addition, the switching characteristics of MFSM and MFS were different from those of MFM, especially after a few cycles, related to the oxygen vacancy migration between a-IGZO channels and HZO films. The extracted 2Pr values for MFS, MFSM and TiN/HZO/Mo (MFM, FeTFT source/drain parasitic capacitor) were 38, 28 and 20 [μC cm-2], respectively. Based on the operation differences according to the device structure, it was found that irreversible switching in the MFS region (channel) causes a rapid decrease in the memory window after the first switching in an FeTFT and degradation of a-IGZO and HZO films in the MFSM region (contact) including oxygen vacancy exchange and related defect generation causes subthreshold slope increases and negative threshold voltage shifts as cycling stress was applied.

In2O3-based thin-film transistors with a (400) polar surface for CO2 gas detection at 150 °C

Because of increasing demand for CO2 detection, CO2 sensors capable of low-temperature operation are desired. However, conventional oxide semiconductor sensors still require high operating temperatures. In this study, we fabricated a CO2 sensor that can operate at 150 °C. The sensor is based on an open-channel-type thin-film transistor (TFT) structure with an In2O3(400) polar plane as a channel. Because the In2O3(400) surface is polar, many OH groups are adsorbed onto the as-prepared surface. When CO2 gas is introduced, CO2 molecules react with the OH groups and the TFT characteristics change. As a result, CO2 can be detected with a sensitivity 2.9 times greater than that under an inert N2 atmosphere despite the operating temperature of only 150 °C. In a TFT with nonpolar In2O3(222) planes, the sensitivity remains at 1.3 times. We therefore believe that TFTs fabricated with the polar surface of an oxide semiconductor are useful for gas-sensing applications.

Atomically Thin Amorphous Indium-Oxide Semiconductor Film Developed Using a Solution Process for High-Performance Oxide Transistors.

High-performance oxide transistors have recently attracted significant attention for use in various electronic applications, such as displays, sensors, and back-end-of-line transistors. In this study, we demonstrate atomically thin indium-oxide (InOx) semiconductors using a solution process for high-performance thin-film transistors (TFTs). To achieve superior field-effect mobility and switching characteristics in TFTs, the bandgap and thickness of the InOx were tuned by controlling the InOx solution molarity. As a result, a high field-effect mobility and on/off-current ratio of 13.95 cm2 V-1 s-1 and 1.42 × 1010, respectively, were achieved using 3.12-nanometer-thick InOx. Our results showed that the charge transport of optimized InOx with a thickness of 3.12 nm is dominated by percolation conduction due to its low surface roughness and appropriate carrier concentration. Furthermore, the atomically thin InOx TFTs showed superior positive and negative gate bias stress stabilities, which are important in electronic applications. The proposed oxide TFTs could provide an effective means of the fabrication of scalable, high-throughput, and high-performance transistors for next-generation electronic applications.