Characteristics Of Bioaerosols Research Articles

Experimental study on bioaerosols behavior and purification measures in a subway compartment.

Bioaerosols in public transportation systems raise critical environmental concerns, seriously threatening passenger health and safety. In this study, we investigate the spread characteristics of bioaerosols in a standard type-B subway compartment using both air sampling and sediment sampling methods. Additionally, without compromising indoor passenger comfort, two self-designed air purification devices, based on intense field dielectric (IFD) and dielectric barrier discharge (DBD) technologies, respectively, are successfully applied for the improvement of the subway air quality. The results show that bioaerosols can propagate rapidly throughout the entire compartment in 5min via airborne transmission. Under the effect of the symmetric air ducts and compartment structure, the difference in bioaerosol concentration in the air is less than 10% between both ends of the compartment. Concurrent substantial bioaerosol deposition on the ground, seats, and windows underscores the risk of contact transmission. Furthermore, the real-time purification rates of the two devices integrated into the air conditioning system reach 59.40% and 44.98%, respectively. With their demonstrated high efficiency in purifying bioaerosols and modular design featuring low energy consumption, easy cleaning, and reusability, these devices stand out as viable long-term solutions for large traffic vehicles. These research findings provide practical equipment recommendations and installation strategies for optimizing indoor air quality in subways and are applicable to other similar transportation systems.

Diffusion behavior and transport risk of bioaerosol particles in a domestic waste landfill site in an arid and cold region of northwestern China

Bioaerosols have attracted increasing attention as novel contaminants because of their potential role in the spread of disease. In this study, sampling sites were established in a landfill in northwestern China with the aim of investigating the emission and diffusion characteristics of bioaerosols. The results revealed that the counts of airborne bacteria released by landfill cover area (LCA) and waste dumping area (WDA) located in the landfill area reached 18 193 ± 30 CFU/m3 and 10 948 ± 105 CFU/m3, respectively. These two aeras were the main sources of bioaerosol generation. Meanwhile, Corynebacterium spp., Bacteroidetes spp., and Pseudomonas spp. were identified as potential pathogens. A Gaussian model was applied to simulate the diffusion of the bioaerosols; the influence distance was calculated as 12 km from the boundary of the landfill site. The potential health risks of bioaerosol exposure to on-site workers and nearby residents were calculated and evaluated in terms of aerosol concentration, particle size, and pathogenic bacteria. The present study promotes the recognition of the emission behavior of microorganisms in aerosol particles and provides a basis for controlling bioaerosol contamination from landfill sites, particularly those located in cold and arid northwestern regions of China.

Association among polydisperse aerodynamic size of bioaerosols, biodiversity and urbanization in kindergartens

The aerodynamic sizes of bioaerosols may significantly affect their behaviors, respiratory deposition and biodiversity. The respirable bacterial size, biodiversity, and human-associated bacteria (HAB) related bioaerosols were evaluated at three kindergartens in Taiwan. Kindergartens A, B, and C were in urban, semi-urban, and rural areas, respectively. A six-stage viable Andersen cascade impactor was used to collect bioaerosols and to determine their size distributions. The geometric mean diameter (GMD), geometric standard deviation (GSD), heat maps, and uniformity were used to evaluate the association of bacteria characteristics. A BD Phoenix-100 automated interpretation system was used to identify the airborne bacteria species.The results revealed that 1425 colonies of the sampled airborne bacteria contained 63 species in 29 genera, and overall, 63.0% were HABs. The most abundant phylum was Actinobacteria (56.6 ± 22.2%) and Firmicutes (31.6 ± 22.3%), and from the taxonomic analysis, both airborne Micrococcus and the Staphylococcus aureus are the dominant genus. All the bacteria aerodynamic particle size distributions were polydisperse distributions. The heat map and uniformity analysis had revealed most of the sampled bioaerosols distributed between 1.1–3.3 μm, and most of the polydisperse airborne Streptococcus spp. had a size in the respirable range, due to urbanization, they have potentially contributed to respiratory risk in the kindergartens. The Shannon diversity index (H) and inverse Simpson diversity index (D) of the bioaerosols in urban kindergarten were negatively correlated with GMD and GSD. The Pearson correlations revealed that the kindergarten in the rural area, with a higher temperature, a lower relative humidity, and a lower CO2 concentration than the others, tended to have the largest H and D values (P < 0.05). Multiple and stepwise regression revealed that bioaerosol aerodynamic size was statistically significantly correlated with H (P = 0.001) and D values (P = 0.002). This study sheds light on the characteristics of bioaerosols and their associations with microbiome.

Contribution of Particulates to Airborne Disease Transmission and Severity: A Review.

The emergence of coronavirus disease 2019 (COVID-19) has catalyzed great interest in the spread of airborne pathogens. Airborne infectious diseases are classified into viral, bacterial, and fungal infections. Environmental factors can elevate their transmission and lethality. Air pollution has been reported as the leading environmental cause of disease and premature death worldwide. Notably, ambient particulates of various components and sizes are harmful pollutants. There are two prominent health effects of particles in the atmosphere: (1) particulate matter (PM) penetrates the respiratory tract and adversely affects health, such as heart and respiratory diseases; and (2) bioaerosols of particles act as a medium for the spread of pathogens in the air. Particulates contribute to the occurrence of infectious diseases by increasing vulnerability to infection through inhalation and spreading disease through interactions with airborne pathogens. Here, we focus on the synergistic effects of airborne particulates on infectious disease. We outline the concepts and characteristics of bioaerosols, from their generation to transformation and circulation on Earth. Considering that microorganisms coexist with other particulates as bioaerosols, we investigate studies examining respiratory infections associated with airborne PM. Furthermore, we discuss four factors (meteorological, biological, physical, and chemical) that may impact the influence of PM on the survival of contagious pathogens in the atmosphere. Our review highlights the significant role of particulates in supporting the transmission of infectious aerosols and emphasizes the need for further research in this area.

Spatial and temporal distribution of bioaerosols produced by patients with different postures in a negative pressure isolation ward under different ventilation modes

The high concentration of viral bioaerosols within the negative pressure isolation wards could pose a challenge to preventing potential cross-infection amongst healthcare workers (HCWs) and patients. Using the Euler–Lagrange methodology, this study numerically simulated the spatial and temporal distribution characteristics of bioaerosols in a typical negative pressure isolation ward as well as determined the interaction of ventilation mode and patient posture on ward ventilation performance. The removal effect of particle groups produced by two respiratory behaviours (breathing and coughing) was quantitatively analyzed, and the effect of exhaust air ratio and air exchange rate on particle distribution was discussed. The results showed that the migration characteristics of bioaerosol particles were sensitive to both the ventilation pattern and patient posture, which showed significant interactions. On this basis, the ventilation pattern with the best ventilation performance was evaluated, showing a particle removal effect of 70–85%. Due to the initial momentum difference, the diffusion behaviour of cough and breath particles was not consistent, but optimizing the airflow distribution near the exhaust outlet could improve their removal efficiency in the meantime. Further studies found that equal exhaust air velocity ratio facilitated the removal of aerosol particles, and an appropriate increase in the air exchange rate could also reduce the particle content.

Size-segregated characteristics of bioaerosols during foggy and non-foggy days of winter, meteorological implications, and health risk assessment

Fog is a common atmospheric event in northern India.

Characteristics of bioaerosols under high-ozone periods, haze episodes, dust storms, and normal days in Xi’an, China

The characteristics of bioaerosols and their effects on human beings’ health have become a major public concern in the recent years. This study compared the characteristics of bioaerosols under different types of pollution (high-ozone [HO] episodes, haze episodes, and dust storms [DSs]), with those of bioaerosols on normal days (NDs) in Xi'an, China. The concentrations, diurnal variations, and size distribution of bacteria, fungi, and total airborne microbes (TAMs) were investigated. The results showed that the bacterial and fungal concentrations were the highest during DSs and on NDs, reaching 425.2 and 956.9 colony-forming units/m3, respectively. The concentration of TAMs was the highest during HO episodes, reaching 10.7 × 106 cells/m3, which was significantly higher than that during the other events. The maximum concentrations of bacteria and fungi during HO episodes were observed in the morning, while they appeared separately in the morning and evening during haze episodes. Bacteria and TAMs during DSs reached peak concentrations in the morning and evening, which is opposite to the particulate matter (PM) distribution pattern. On NDs, temperature and relative humidity had significant effects on bioaerosols. The size distributions of airborne bacteria exhibited bimodal patterns, whereas unimodal distributions were observed for fungi. Fungi mainly attached in fine particles (<2.1 μm) with proportions of 67.4% and 60.5% during haze episodes and DSs, respectively, which means that fungi were easily penetrated into the human respiratory system. The evaluation of influence factors revealed that PM2.5 and PM10 had negative effects on fungal concentration during DSs, and ozone concentration and temperature were inversely correlated with fungal concentration during HO episodes. These results provide valuable reference data for elucidating the formation and evolution of bioaerosols under different types of pollution.

Characteristics of bioaerosols in kindergarten classrooms in Miaoli City

Characteristics of bioaerosols in kindergarten classrooms in Miaoli City

Distribution Characteristics and Factors Influencing Culturable Bacterial Bioaerosols on a Dairy Farm in Northern China

Studying the distribution characteristics of bioaerosols and their interaction with the environment is crucial for dairy farms. The distribution of aerosols differs in dairy farming from farming of other livestock, and their sensitivity to environmental factors varies across sites. Field experiments were conducted in an intensive commercial dairy farm in Northern China to investigate the horizontal and vertical distribution of culturable bacterial bioaerosols. Concentration levels and particle size ranges were analyzed, and the impact of multiple environmental factors on culturable bacterial bioaerosols was assessed. Significant variations in culturable bacterial bioaerosol concentrations were observed across eight functional zones, ranging from 1.14 × 103 to 7.35 × 103 CFU/m3. Culturable bacterial bioaerosols exhibited consistent carrier distribution patterns across six different size ranges. Vertical analysis revealed significantly higher culturable bacterial bioaerosol concentrations at a 1 m height compared to 4 m (p &lt; 0.05), while similar size distributions were observed at different heights of the same sampling location. The top three environmental factors influencing culturable bacterial bioaerosol concentrations were PM100 concentration, wind direction, and air temperature. This study provides insights into the distribution characteristics of culturable bacterial bioaerosols on dairy farms and their response to environmental factors. The findings serve as a reference for evaluating bioaerosol emissions and establishing daily disinfection management measures on dairy farms.

Study on the migration characteristics of bioaerosols and optimization of ventilation patterns in a negative pressure isolation ward considering different patient postures.

Due to the serious global harm caused by the outbreak of various viral infectious diseases, how to improve indoor air quality and contain the spread of infectious bioaerosols has become a popular research subject. Negative pressure isolation ward is a key place to prevent the spread of aerosol particles. However, there is still limited knowledge available regarding airflow patterns and bioaerosol diffusion behavior in the ward, which is not conducive to reducing the risk of cross-infection between health care workers (HCWs) and patients. In addition, ventilation layout and patient posture have important effects on aerosol distribution. In this study, the spatial and temporal characteristics as well as dispersion patterns of bioaerosols under different ventilation patterns in the ward were investigated using the computational fluid dynamics (CFD) technique. It is concluded that changes in the location of droplet release source due to different body positions of the patient have a significant effect on the bioaerosol distribution. After optimizing the layout arrangements of exhaust air, the aerosol concentration in the ward with the patient in both supine and sitting positions is significantly reduced with particle removal efficiencies exceeding 95%, that is, the ventilation performance is improved. Meanwhile, the proportion of aerosol deposition on all surfaces of the ward is decreased, especially the deposition on both the patient's body and the bed is less than 1%, implying that the risk of HCWs being infected through direct contact is reduced.

The pollution of bioaerosols in hospital sewage purification process: Composition characteristics, seasonal variation and risk assessment

The hospital sewage contains many pathogenic bacteria, which may produce bioaerosol and spread diseases during the sewage treatment process. In this study, the characteristics, seasonal variation, and risk assessment of the bioaerosol in hospital sewage treatment stations (HSTS) were analyzed. The concentration of bacteria in bioaerosol generated from BRT (251 CFU/m3) was higher than that in the air at SG (75 CFU/m3). Summer (506 CFU/m3) and autumn (32 CFU/m3) showed the highest levels of bacterial and intestinal bacterial concentration in the air at BRT, respectively. The percentage of microorganisms attached to small particles (<2.1 μm) (SP) ranged from 22.64% to 66.66%, which was most prevalent in winter (66.66%). Brevundimonas (38.99%), Bacteroides (11.25%), Pseudomonas (49.48%), and Ochrobactrum (41.02%) were the dominant genera in spring, summer, autumn, and winter, respectively. The dominant bacterial genera of bioaerosol in BRT and SG showed obvious seasonal variations, Bacillus were present in each season. The hazard quotient (HQ) of males was higher than that of females (HQmales: 2.60 × 10−3, HQfemales: 2.18 × 10−3), and the inhalation risks of the bacteria were highest in summer (5.98 × 10−2). Temperature and relative humidity positively influenced intestinal bacteria in bioaerosols. The potentially pathogenic were highest in spring. One hour after the sampling point, the result of the Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) mode showed that the diffusion area of bioaerosol in winter (182.03 km2) was the largest. This study focused on the bioaerosol produced by hospital sewage. The results effectively revealed the seasonal variation and risk characteristics of bioaerosols, which could serve as a theoretical foundation for the future control and reduction of bioaerosols in the process of purifying municipal water.

Bioaerosol Identification by Wide Particle Size Range Single Particle Mass Spectrometry

The properties of bioaerosols are complex and diverse, and have a direct impact on the environment, climate, and human health. The effective identification of bioaerosols in the atmosphere is very significant with regard to accurately obtaining the atmospheric chemical characteristics of bioaerosols and making biological early warnings and predictions. To improve the detection of large particle bioaerosol and non-bioaerosol interference in the process of bioaerosol recognition this study detected a variety of bioaerosols and abiotic aerosols based on a single particle aerosol mass spectrometer (SPAMS). Furthermore, the bioaerosol particle identification and classification algorithm based on Zawadowicz the ratio of phosphate to organic nitrogen is optimized to distinguish bioaerosols from abiotic aerosols. The influence of ionized laser energy on classification methods is thoroughly explored here. The results show that 15 kinds of pure fungal aerosols were detected by SPAMS based on a wide size range sampling system, and that fungal aerosols with a particle size of up to 10 μm can be detected. Through the mass spectra peak ratio method of PO3−/PO2− and CNO−/CN−, when discriminating abiotic aerosols such as disruptive biomass combustion particles, automobile exhaust, and dust from pure bacterial aerosols, the discrimination degree is up to 97.7%. The optimized ratio detection method of phosphate to organic nitrogen has strong specificity, which can serve as the discriminant basis for identifying bioaerosols in SPAMS analytical processes.

On-site investigation of the concentrations and size distributions of bioaerosols in the underground garages

Bioaerosol concentrations and sizes in indoor environment are associated with human health. Among various indoor environments, the knowledge of the bioaerosol characteristics in underground garages remains unclear. In this study, both DAPI (4′,6-diamidino-2-phenylindole) staining and culturable methods were performed to determine the concentrations and size distributions of bioaerosols in two typical underground garages (an office building (UBOB) and a commercial building (UBCB)) in Xi'an, China. Results indicated that bioaerosol concentrations showed seasonal variations in two garages. The total bioaerosol concentrations were higher in summer (UBOB: (1.07 ± 0.29) ✕105 cells/m3; UBCB: (0.59 ± 0.23) ✕105 cells/m3) than winter (UBOB: (0.34 ± 0.17) ✕105 cells/m3; UGCB: (0.38 ± 0.15)✕105 cells/m3). Higher concentrations of bioaerosols were also found during the rush hour than other times due to the elevated traffic volumes. The spatial distribution of bioaerosols was relatively even for most sampling sites in two garages. Moreover, over 80% of airborne culturable fungi and over 65% of airborne culturable bacteria were in respirable size range (<4.7 μm). Importantly, airborne culturable fungal concentrations in two garages exceeded the proposed thresholds by the World Health Organization (WHO) (500 CFU/m3), with the exceeding standard rate (ESR) of 80.28% and 82.60%, respectively, at UGOB and UGCB, implying that necessary control measures should be taken to reduce microorganism contamination in the air of underground garages. The present results may provide the scientific basis for better understanding pollution characteristics of bioaerosols and formulating prevention and control measures in underground garages.

Bioaerosol-related studies in wastewater treatment plant with anaerobic-anoxic-oxic processes: Characterization, source analysis, control measures

Sewage in wastewater treatment plants (WWTPs) can produce fugitive bioaerosols that pose a health risk to employees and residents. This study aimed to fugitive bioaerosols from two WWTPs with anaerobic-anoxic-oxic (AAO) processes, and bioaerosols control measures were proposed based on the results of these studies. It was found that the bioaerosols were mainly composed of microorganisms from dominant genera such as Romboutsia, Rubellimicrobium, Sphingomonas, Acidea, Cryptotrichosporon and water-soluble ions dominated by SO42−. Moreover, total suspended particulate (TSP), relative humidity (RH), wind speed (WS), Ca2+, NH4+, Na+, Cl−, NO3−, and K+ had positive effects on most dominant genera, while temperature (T) and SO42− had negative effects on most dominant genera. The source analysis showed that the bioaerosols in the indoor treatment facility’s fine screen room and sludge dewatering plant mainly originated from sewage or sludge, and those in the aeration tank of the outdoor treatment facility mainly originated from the background air of WWTPs . By combining the characteristics of bioaerosols and the results of source analysis, targeted control measures were proposed from three aspects: source reduction of bioaerosol fugitives, control of bioaerosol propagation, and collection and treatment systems. This study provides the theoretical basis and ideas for controlling bioaerosols in WWTPs with AAO processes.

Dispersion characteristics of bioaerosols during treatment of rural solid waste in northwest China

In rural China, the release of bioaerosols containing pathogens from solid waste dumps poses a potential health risk to the local population. Here, we sampled bioaerosols from rural solid waste-treatment in four provinces of northwest China to investigate their emission and dispersion characteristics in order to provide a scientific basis for control and risk reduction of bioaerosols released from rural sanitation facilities. The airborne bioaerosol concentrations and particle size distributions were calculated using an Anderson six-stage airborne microbial sampler and counting with its internal Petri dish culture. High-throughput sequencing was used to characterize the microbial composition at different sampling sites and to explore possible influencing factors, while the health risk associated with exposure was estimated based on average daily dose-rate. The highest concentration point values of bacteria and fungi in bioaerosols near the solid waste were 63,617 ± 15,007 and 8044 ± 893 CFU/m³, respectively. Furthermore, the highest concentration point values of Enterobacteriaceae was 502 ± 35 CFU/m³. Most bioaerosols were coarse particles larger than 3.3 μm. Potentially pathogenic genera of winter-indicator species detected in the air were primarily Delftia, Rhodococcus and Aspergillus. The composition of solid waste and environmental conditions are important factors in determining the characteristics of bioaerosols. Local residents are exposed to bioaerosols mainly through inhalation. Children are at a particularly high risk of exposure through both inhalation and skin contact. The results of this study show that bioaerosols in the vicinity of rural solid waste dumps pose a health risk to the surrounding population. More suitable risk assessment criteria for rural areas should be established, and corresponding control and protection measures should be taken from three aspects: generation source and transmission pathway, as well as the recipient.

ADMS simulation and influencing factors of bioaerosol diffusion from BRT under different aeration modes in six wastewater treatment plants

Bioaerosols produced by municipal wastewater treatment plants (MWTP) can spread in air, thereby polluting the atmosphere and causing safety hazards to workers and surrounding residents. In this study, the biological reaction tanks (BRTs) of six MWTPs undergoing typical processes in North China, Yangtze River Delta, and the Greater Bay Area were selected to set up sampling points and investigate the production characteristics of bioaerosols. The Atmospheric Dispersion Modelling System method was used to simulate the diffusion of bioaerosols in the MWTPs. The concentrations of bacteria and, specifically, intestinal bacteria in the bioaerosols ranged from 389 CFU/m3 to 1,536 CFU/m3 and 30 CFU/m3 to 152 CFU/m3, respectively, and the proportion of the intestinal bacteria was 8.85%. The concentration of soluble chemicals (SCs) in the bioaerosols was 18.36 μg/m3–82.19 μg/m3, and the main SCs found were Mg2+, Ca2+, and SO42−. The proportion of intestinal bacteria (75.79%) produced via surface aeration by a BRT attached to large-sized bioaerosol particles was higher than that of a BRT undergoing the bottom aeration process (37.28%). The main microorganisms found in the bioaerosols included Moraxellaceae, Escherichia–Shigella, Psychrobacter, and Cyanobacteria. The generation of bioaerosols exhibited regional characteristics. The wastewater treatment scale, wastewater quality, and aeration mode were the main factors influencing bioaerosol production. Model simulation showed that, after 1 h, the diffusion distance of bioaerosol was 292 m–515 m, and the affected area was 42,895 m2–91,708 m2. The diffusion distance and range of the bioaerosols were significantly correlated with the concentration at the bioaerosol source and the aeration mode adopted by the BRTs. Wind speed and direction were two environmental factors that affected the diffusion of bioaerosols. With an increase in the diffusion distance, the concentration of microorganisms, intestinal bacteria, ions, and fine particles in the bioaerosols decreased significantly, resulting in a corresponding reduction in the exposure risk. This study provides new insights to help predict bioaerosol risks at MWTPs and identify safe areas around MWTPs. The study also provides a basis for selecting safe MWTP sites and reducing bioaerosol pollution risks.

The influence of air supply inlet location on the spatial-temporal distribution of bioaerosol in isolation ward under three mixed ventilation modes

The outbreak of COVID-19 and the spread of infectious pathogens through bioaerosols have once again aroused widespread concern worldwide. Isolation ward is an important place to prevent the spread of infectious bioaerosols. However, infection of health care workers (HCWs) in the isolation ward often occurs, so it is urgent to carry out relevant research to reduce the cross-infection between HCWs and patients. In this paper, the temporal and spatial distribution characteristics of bioaerosols under three mixed ventilation modes in a single ward were studied, namely, upper supply side return air of Case 1 and side supply and side return ventilation are Case 2 and Case 3 respectively. The results show that the removal efficiency of bioaerosol in the ventilation mode of Case 3, in which directional airflow is formed from the air supply inlet to the release source and then to the exhaust outlet, is 46.6% and 67.7% higher than that of Case 1 and Case 2, respectively. In addition, ventilation methods based on mixed theory do not guarantee good air quality in the breathing zone (1.3 m to 1.7 m) of HCWs, which may increase the inhalation risk for HCWs. It is hoped that our results can provide some useful suggestions for optimizing the airflow layout of the isolation ward, reducing the risk of cross-infection, and virus elimination.

Dispersion Characteristics of Bioaerosols During Treatment of Rural Solid Waste in Northwest China

Dispersion Characteristics of Bioaerosols During Treatment of Rural Solid Waste in Northwest China

Dispersion Characteristics of Bioaerosols During Treatment of Rural Solid Waste in Northwest China

Dispersion Characteristics of Bioaerosols During Treatment of Rural Solid Waste in Northwest China

Dispersion Characteristics of Bioaerosols During Treatment of Rural Solid Waste in Northwest China

Dispersion Characteristics of Bioaerosols During Treatment of Rural Solid Waste in Northwest China