Channel Centerline Research Articles

Morphological changes of river Bank Erosion and channel shifting assessment on Arial Khan River of Bangladesh using Landsat satellite time series images

The continuous processes of erosion and deposition in rivers are intricately linked to changes in land use and land cover (LULC), reflecting dynamic landscape transformations. This study investigates the rate of riverbank erosion, channel shifting, and the impact of erosion on LULC dynamics along the Arial Khan River. Utilizing GIS and remote sensing techniques, we analyzed time-series satellite images from 1993 to 2024 within a 2 km buffer zone of the floodplain. Supervised classification methods were applied for LULC analysis, with results validated using confusion matrices to assess classification accuracy. ArcGIS 10.8 was employed to analyze channel centerline migration, while NDVI analysis assessed vegetation health. The study reveals that between 1993 and 2024, 5142.60 ha were lost to erosion, while deposition affected 4756.52 ha, with erosion surpassing deposition overall. The river shifted an average of 0.66 km during this period, with higher migration rates in Muladi Upazila compared to Babuganj Upazila. Settlement areas expanded significantly from 137.82 ha in 1993 to 2768.68 ha in 2024, while agricultural land declined substantially. These findings provide valuable insights for policymakers to address erosion severity in confluence zones and lay the groundwork for sustainable land management practices.

Elasto-inertial focusing and rotating characteristics of ellipsoidal particles in a square channel flow of Oldroyd-B viscoelastic fluids

The elasto-inertial focusing and rotating characteristics of spheroids in a square channel flow of Oldroyd-B viscoelastic fluids are studied by the direct forcing/fictitious domain method. The rotational behaviours, changes in the equilibrium positions and travel distances are explored to analyse the mechanisms of spheroid migration in viscoelastic fluids. Within the present simulated parameters (1 ≤ Re ≤ 100, 0 ≤ Wi ≤ 2, 0.4 ≤ α ≤3), the results show that there are four kinds of equilibrium positions and six (five) kinds of rotational behaviours for the elasto-inertial migration of prolate (oblate) spheroids. We are the first to identify a new rotational mode for the migration of prolate spheroids. Only when the particles are initially located at a corner and wall bisector, some special initial orientations of the spheroids have an impact on the final equilibrium position and rotational mode. In other general initial positions, the initial orientation of the spheroid has a negligible effect. A higher Weissenberg number means the faster the particles migrate to the equilibrium position. The spheroid gradually changes from the corner (CO), channel centreline (CC), diagonal line (DL) and cross-section midline (CSM) equilibrium positions as the elastic number decreases, depending on the aspect ratio, initial orientation and rotational behaviour of the particles and the elastic number of the fluid. When the elastic number is less than the critical value, the types of rotational modes of the spheroids are reduced. By controlling the elastic number near the critical value, spheroids with different aspect ratios can be efficiently separated.

Electrotaxis of Self-Propelling Artificial Swimmers in Microchannels.

Biological microswimmers alter their swimming trajectories to follow the direction of an applied electric field, exhibiting electrotaxis. We show that synthetic active droplet microswimmers also autonomously change swimming trajectories in microchannels, even undergoing "U-turns," in response to an electric field, mimicking electrotaxis. We exploit such electrotaxis, in the presence of an external flow, to robustly tune the swimming trajectory of active droplets between wall-adjacent, oscillatory, and channel centerline swimming. A general hydrodynamic model demonstrates that the electrotactic dynamics is governed by the electrical effects due to the swimmer's inherent surface charge, besides its motility, hydrodynamic wall interactions, and relative orientations of the electric field and imposed flow. Our study demonstrates a simple method for controlling active agents in complex geometries for microrobotic applications, like autonomous cargo delivery.

Bifurcate migration of neutrally buoyant particles in unilateral slippery channel flows

As an important technique for manipulating particles in fluid–solid channel flows, inertial focusing encourages the design of the channel geometry to enhance particle radial aggregation. Traditional methods typically use exquisite sheathes or elbows to create constricted flows, which ultimately increase flow resistance and lower fluid–solid separation efficiency. This paper presents a slippery wall modification technique that, by regulating the channel flows, is expected to induce nontrivial particle lateral migrations. More specifically, interface-resolved simulations are performed using the lattice Boltzmann method. A slip boundary condition is applied to the redesigned hydrophobic bottom wall. It is observed that the typical bifurcate migration, i.e., particles moving divergently toward the upper and lower equilibrium positions around a crucial location (CL), does not occur along the channel centerline. The CL is always below the centerline, and it decreases consistently with an increase in Kn or Re. By increasing Re, particles are prone to approach the channel centerline. With larger Kn, particles in the higher equilibrium position are affected in the same way, but their lower counterparts are drawn to the bottom wall.

Flow dynamics and channel changes at Yamuna River in Delhi-National Capital Region, India

ABSTRACT The present work was carried out on River Yamuna passing through Delhi-National Capital Region (Delhi-NCR) of India for a stretch of about 125 km to assess the fluvial characteristics in the highly human-dominated region for a period of 200 years with the help of historical maps, topographical maps and satellite data with integration of geographic information system (GIS) environment. Erosion, deposition and channel stability data were analyzed for 1977–1986, 1986–1996, 1996–2006, 2006–2016, and 2016–2022 period. Digital Shoreline Analysis System (DSAS) application was utilized to quantify river channel movement with average channel migration of 22.8 m/year. Westward migration is 4149.2 m maximum in length and eastward migration is about 4083.8 m. The river has migrated a total of 32.26 km2 of area during 1955-2022. The findings indicate that various human activities, such as engineering structures, sand mining, embankments, urbanization, land use/land cover changes, and canal networks, have significantly impacted the river. The DSAS application was also used to predict the position of river channel centerline in future for 2032 and 2042 with channel length of 132.5 and 141.6 km respectively.

Bayesian-inverted laser Thomson scattering measurements indicate electrostatic erosion pathways in magnetically-shielded Hall effect thrusters

Magnetically shielded Hall effect thrusters suffer from pole erosion as their life-limiting mechanism. However, the dominant physical mechanism causing this erosion remains unclear, limiting the ability create designs that mitigate erosion and the predictive accuracy of simulations used to aid in design. This paper provides spatially resolved laser Thomson scattering measurements of electron temperature and density in the near field plume of a magnetically shielded Hall effect thruster, traversing the front pole region from the discharge channel centerline to the cathode centerline. The signals are inverted in a Bayesian framework, and the data are compared qualitatively and quantitatively to simulations of the same Hall effect thruster. Based on the electron momentum equation, electron pressure gradient is used as a proxy for the electron-predicted electrostatic potential gradient. To within the accuracy of this approximation, the electron pressure has a minimum immediately in front of the front pole. Hence, ions have an electrostatic potential avenue from the discharge region to the front pole, validating this mechanism of pole erosion.

Hybrid Modeling of Miniaturized 50 W Annular Hall Thruster

A 50-W-class annular Hall thruster is studied with a hybrid axial–radial two-dimensional model. Ions are described by a kinetic approach, whereas fluid conservation equations are solved for electrons. In such models, additional (anomalous) contributions must be added to the momentum-transfer electron collision frequency to obtain realistic values of the cross-field electron mobility. First, a parametric study is performed, where anomalous transport is described with a simple two-region model based on constant empirical parameters. The simulated global performance is subsequently compared with experimental measurements. Then, laser-induced fluorescence ion velocity measurements are employed to infer a continuous profile of the anomalous electron collision frequency along the channel centerline. The model reproduces the performance, the acceleration structure, the current oscillations, and the doubly charged ion fraction of the laboratory thruster. Measurements of the ion velocity distribution function highlight the presence of a slow ion population in the near plume. The production of the slow ions and their growth for increasing distances from the thruster channel exit is qualitatively reproduced by the model. The results obtained suggest that the generation and dynamics of the observed slow ions can be attributed to the presence of energetic electrons in the plume.

A numerical study of Elasto-inertial particle-focusing in straight and serpentine microchannels

Microfluidic devices have gained popularity in recent years due to their low cost and simplicity. Cell focusing linked with cell counting and cell separation used in clinical tests and point-of-care devices stands towards the top of every list of microfluidic applications. To focus and manipulate particles in a Newtonian medium, inertial microfluidics has been widely used. There is a requirement to replace a significantly more efficient approach given various particle-focusing positions near the channel walls recorded by inertial microfluidics. Here, the synergetic effect of elastic and inertial forces in relatively low-concentration viscoelastic fluids was investigated numerically. Utilizing particle-focusing behavior in straight and serpentine channels with different corner angles, by applying the numerical results obtained using the developed direct numerical simulation method (DNS) for elastic and inertial forces, we created a microchannel with a remarkable performance. As the flow regime transitions to elasto-inertial, where inertial forces are comparable to elastic forces in a straight microchannel, particles tend to concentrate at the channel centerline. As the flow rate increases, however, particle defocusing develops, and shear gradient lift forces ultimately overcome elastic forces in the channel's central region. Given that fluid flows at a higher velocity in the serpentine channel with a corner angle of 75° than in other channels, the Dean drag force induced by secondary flow serves to reduce particle defocusing rate at a given flow rate, making this channel a desirable platform for Elasto-inertial microfluidics. Particle focusing in a vertical direction was noticed as a benefit of elasto-inertial microfluidics, regardless of the geometry or flow rate of the particles passing through the channel. Finally, the impact of particle diameter on focusing behavior was studied. As particle diameter decreases, focusing width decreases and the focusing band shifts to the left side of the cross-section. We expect that the numerical evaluation of using viscoelastic medium in complex geometries can contribute to accelerate the three dimensional particle-focusing mechanism and enhance the efficiency of microdevices for cell and particle manipulation.

Research on the Relative Placement Angle of the Induction Heater and the Channel in a Four-Channel Induction-Heating Tundish.

In order to optimize the application effect of induction heating (IH) tundishes, a four-channel IH tundish is taken as the research object. Based on numerical simulation methods, the influence of different relative placement angles of induction heaters and channels on the electromagnetic field, flow field and temperature field of the tundish is investigated. We focus on comparing the magnetic flux density (B) and electromagnetic force (EMF) distribution of the channel. The results show that regardless of the relative placement angle between the heater and the channel, the distribution of B in the central circular cross-section of the channel is eccentric. When the heater rotates around channel 1 towards the bottom of the tundish, the distribution of B in the central circular cross-section of the channel changes from a horizontal eccentricity to a vertical one. Through the analysis of the B contour in the longitudinal section of the channel, the difference in effective magnetic flux density area (ΔAB) between the upper and lower parts of the channel can be obtained, thereby quantitatively analyzing the distribution of B in this section. The distribution pattern of ΔAB is consistent with the distribution pattern of the electromagnetic force in the vertical direction (FZ) of the channel centerline. The ΔAB and FZ of channel 1 gradually increase as the heater rotates downwards, while those of channel 2 reach their maximum value at a rotation angle of 60°. Compared to the conventional placement, when the heater rotation angle is 60°, the outlet flow velocities at channel 1 and channel 2 decrease by 15% and 12%, respectively. However, the outlet temperature at channel 2 increases by 1.96 K, and the molten steel flow at the outlet of channel 1 and channel 2 no longer exhibits significant downward flow. This shows that when the heater rotation angle is 60°, it has a dual advantage. On the one hand, it is helpful to reduce the erosion of the molten steel on the channel and the bottom of the discharging chamber, and on the other hand, it can more effectively exert the heating effect of the induction heater on the molten steel in the channel. This presents a new approach to enhance the application effectiveness of IH tundish.

Continuously tunable separation of light-induced Haematococcus pluvialis using an ultrastretchable, sheath-flow-assisted elasto-inertial microchannel

BackgroundA proportion of Haematococcus pluvialis under the light stress can effectively conduct astaxanthin biosynthesis, leading to the increase in cell size. Although the size is a critical indicator for identifying the astaxanthin-rich H. pluvialis cells, the cut-off size to be separated varies from sample to sample. ResultsHere, we report an ultrastretchable, straight elasto-inertial microchannel with tunable separation threshold to continuously separate the light-induced H. pluvialis cells by size. The symmetrical sheath flows confine the particles to the channel sidewalls, and large particles can cross the interface of viscoelastic fluids to the equilibrium position at the channel centerline. By stretching the microfluidic chip, the medium-sized particles can gradually migrate to the channel centerline in the narrower and longer channel, bringing the tunable separation threshold. Results show that the separation performance of the ultrastretchable microfluidic device is affected by total flow rate, flow rate ratio of sheath to sample, polyethylene oxide (PEO) solution configuration. Lastly, size-tunable separation of light-induced H. pluvialis cells is demonstrated. SignificanceTo the best of our knowledge, this is the first report on cell migration in co-flow configurations in the ultra-stretchable microfluidics. Separation of H. pluvialis is not only a relevant end application in harvesting the astaxanthin-rich species, but the separated populations of highly productive microalgal cells will open a venue for cellular directed evolution.

Numerical analysis of thermal-hydraulic influence of geometric flow baffles on multistage Tesla valves in printed circuit heat exchangers

The innovative structure and flexible functionality of Tesla valves have attracted significant attention across various industries. Unlike conventional check valves, which open in response to fluid movement and pressure and close to prevent backflow, Tesla valves utilize interconnected pathways to create a highly efficient and reliable method for regulating fluid flow. However, the thermal–hydraulic influence associated with the utilization of different geometric configurations of flow baffles in Tesla valves remain incompletely understood. This study employs numerical simulations to assess the effectiveness of a printed circuit heat exchanger (PCHE) incorporating three layers of multistage Tesla valves with geometric flow baffles. The simulations, based on solving the Navier-Stokes and energy equations, focus on analyzing the behavior of liquid water within a temperature range of 30 to 90 °C, pertinent to applications such as geothermal heating systems. The employed Tesla valve configuration demonstrates superior performance, exhibiting a notable enhancement in thermal effectiveness ranging from 13 % to 55 % compared to configurations utilizing zigzag, separate, and overlapping NACA 0020 airfoils under otherwise identical conditions. Three crucial geometric parameters are introduced to characterize the shape of flow baffles in multistage Tesla valves: the length from the baffle apex to the baffle half-front sphere, the radius of the baffle half-front sphere, and the distance from the baffle apex to the centerline of the entrance flow channel. Performance evaluation criteria (PEC) indicate that while the overlapping airfoil configuration performs better than both zigzag and separate configurations, the current Tesla valve design achieves approximately a 10–14 % higher PEC value than the overlapping airfoil configuration. The manipulation of geometric parameters for flow baffles is generally believed to be a critical step in the advancement of multistage Tesla valves, contributing to the enhancement of heat transfer and potentially broadening the applicability of these valves to various practical heat transfer systems.

Vortex-shedding and bistability in cylinder-flexible plate assembly in a channel

This study numerically investigates the fluid–structure interaction dynamics of a stationary circular cylinder with an attached flexible splitter plate in a confined fluid domain. We explore how variations in Reynolds number (Re), plate length, offset from the channel centerline, and blockage ratio influence the vortex-shedding and oscillatory behavior of the plates in laminar flow. Results indicate that at low Reynolds numbers (Re = 100), there are no vortex shedding or oscillations, while at higher Reynolds (Re = 200 to 300), the shorter plate exhibits first-mode oscillations and symmetry breaking, whereas the longer plate shows only transient second-mode oscillations at Re = 300 that diminish in amplitude, suggesting that increased plate length reduces vortex-induced forces. Dynamic Mode Decomposition (DMD) analysis confirms consistent primary flow structures across different Reynolds numbers, with initial modes encapsulating the majority of the system’s dynamics. In addition to determining the critical Re for vortex-shedding, vortex-induced oscillations and bistability, the study also examines the critical blockage ratios on the symmetry breaking phenomenon, and also shows that plate stability is influenced by domain asymmetry. These insights enhance understanding of the biomechanics of fish-like robots and inform the design and control of bioinspired flexible structures in fluid flows.

Mixed convection characteristics in a long horizontal lid‐driven channel with periodically distributed local flow modulators

AbstractThis study explores the effectiveness of periodically placed rotating blades in enhancing heat transfer in a channel. The channel consists of a cold top plate moving at a constant speed and a fixed hot plate at the bottom. Thin rotating blades are placed periodically along the channel's centerline, with the spacing between their axes equal to the channel's height. This paper analyzes a transient, two‐dimensional, laminar flow problem using energy, momentum, and continuity equations. To address the challenges posed by moving blades, the Galerkin finite element method is implemented within an arbitrary Lagrangian–Eulerian framework, employing a triangular mesh discretization scheme. This study comprehensively explores thermal and hydrodynamic characteristics, including overall heat transfer, thermal frequency, and power consumption of the rotating blade for heat transfer in mixed convection scenarios with Richardson numbers (Ri) ranging from 0.1 to 10 at varying rotational frequency of the blade. Outcomes demonstrate that the inclusion of a rotating blade increases heat transfer up to 50% at lower Ri, after which the impact of the rotating blade diminishes and heat transfer reduces up to 20% at higher Ri. In addition, heat transfer enhances with increasing blade frequency up to Ri = 6.5, beyond which the effect of the frequency overturns. Examining thermal and hydrodynamic characteristics reveals that the blade achieves optimal performance when operating at f = 1 and Ri = 3. The study's insights into mixed convection heat transfer offer versatile applications, benefiting industries and equipment such as electronic cooling, chemical reactors, food processing, material fabrication, solar collectors, and nuclear reactor systems. Moreover, the findings are instrumental in the thermal ventilation of buildings and the development of micro‐electromechanical systems.

Improving the specific impulse of Hall thrusters using a wide channel design

This paper proposes increasing the width of the discharge channel to improve the specific impulse of Hall thrusters. In our study, we significantly increased the achievable channel width by optimizing the magnetic circuit topology, and the design freedom of the Hall thruster was improved. A prototype of a wide-channel high-specific-impulse Hall thruster was designed and experimentally verified. The effects of channel width on the discharge process and the characteristics of an aft-loaded magnetic field Hall thruster were investigated. The high-intensity luminous region did not diffuse radially with an increase in the channel width, and the plasma was always concentrated near the channel centerline. A wider channel is more conducive for improving the propellant utilization efficiency, thereby effectively improving the specific impulse of the Hall thruster. By optimizing the discharge channel width, the upper limit of the discharge voltage was increased, and the maximum specific impulse was increased from 3170 to 3794 s, a relative improvement of 20%. The effect of the specific impulse improvement at the same discharge voltage was analyzed and discussed. The results of this study are significant for the design of high-specific-impulse Hall thrusters.

Numerical modeling of magnetohydrodynamic non‐Newtonian flow in a cross‐slot

AbstractThis study numerically investigates the characteristics of a non‐Newtonian magnetohydrodynamic flow in a cross‐slot. Numerical simulations are performed using power law, Bird–Carreau and Casson non‐Newtonian fluid models. The flow characteristics and shear viscosity behavior in the flow region are analyzed for different values of magnetic field. Additionally, the dynamic behavior of the bifurcated flow in the cross‐slot is studied in detail, and the computational results are compared with existing models. It is shown that the fluid velocity is reduced in both the inlet and outlet channels of the cross‐slot due to the magnetic field, regardless of the viscosity model. Moreover, it is found that the fluid viscosity increases along the centerline of the inlet channels and decreases in the outlet channels of the cross‐slot for all non‐Newtonian fluid models tested here. Furthermore, this study shows that the flow properties of the non‐Newtonian fluids can be controlled by changing the magnetic field strength. The results of this study will be useful for analyzing the flow behavior of blood in a microfluidic cross‐slot and other rheological fluids used in biochemical engineering and industrial processes, where higher mass transfer and mixing efficiency can be achieved by imposing an external magnetic field.Highlights Simulation of non‐Newtonian magnetohydrodynamic flow in a cross‐slot is conducted. Analysis of the flow and shear viscosity behavior for different Hartman number is performed. Flow properties were successfully controlled with the imposed external magnetic field.

Pressure Pulsation Characteristics of a Self-Priming Pump under Typical Operating Conditions

To investigate the pressure pulsation characteristics of self-priming pumps under different flow conditions, Fluent 19.2 software was used to numerically calculate the internal flow inside a self-priming pump by means of the RNG k-ε model. The pressure pulsation characteristics, as well as the standard deviation in the volute and impeller domains, were analyzed under different flow conditions. As a result, under rated- and high-flow conditions, the monitoring points in the volute channel have obvious periodic patterns, and the peak pressure pulsations all occur in the octave band of the blade frequency. The pressure pulsation amplitude is larger under the high-flow condition than in the other two conditions. The monitoring points L1 and L5 on the impeller channel centerline are located near the impeller’s inlet and outlet, respectively, so the pressure pulsations are larger than other monitoring points.

Xenon tracers for cost effective laser induced fluorescence of alternative propellant Hall thrusters

One of the limiting factors to developing plasma thrusters on alternative propellants is the cost associated with changing the diagnostic tools, which are often propellant-dependent. For laser induced fluorescence (LIF), which is typically used for ion velocity distribution measurements to determine ion trajectories and potential profiles, either new lasers need to be bought, which are tuned to the wavelength of the new element’s excitation level, or a costly tunable laser is required. A method to use existing LIF setups designed for xenon on any propellant has been demonstrated on a Hall thruster operating on krypton. In the demonstration test, a small amount of xenon (0.01%–4%) was mixed with the main krypton propellant for use as a diagnostic tracer, and xenon ion velocities were measured while also monitoring changes in the mean discharge current and oscillations. High signal-to-noise ratios in LIF data acquired along the channel centerline were obtained with tracer gas fractions ≤1% that negligibly affected the thruster operation. These results and comparison of the emission spectra of xenon and other common propellants suggest that the tracer LIF method should be broadly applicable to LIF measurements in Hall thrusters operating on alternative propellants.

Inertial Migration in a Pressure-Driven Channel Flow: Beyond the Segre-Silberberg Pinch.

We examine theoretically the inertial migration of a neutrally buoyant rigid sphere in pressure-driven channel flow, accounting for its finite size relative to the channel width (the confinement ratio). For sufficiently large channel Reynolds numbers (Re_{c}), a small but finite confinement ratio qualitatively alters the inertial lift velocity profiles obtained using a point-particle formulation. Finite size effects lead to new equilibria, in addition to the well-known Segre-Silberberg pinch locations. Consequently, a sphere can migrate to either the near-wall Segre-Silberberg equilibria, or the new stable equilibria located closer to the channel centerline, depending on Re_{c} and its initial position. Our findings are in accord with recent experiments and simulations, and have implications for passive sorting of particles based on size, shape, and other physical characteristics, in microfluidic applications.

Open channel velocity field investigation for hydrokinetic power generation

The paper presents an experimental study of a velocity field in an open channel. The study of water flow in an open channel is complicated due to the influence of various factors and different variables. Some of the variables affecting the flow parameters include the height of the water column, the width of the channel, the length of the channel, the slope of the channel, and the conditions of the channel bed. The investigated open channel is used for experimental research of kinetic turbines, and the flow speed in the channel is in the range of 0.1-0.3 m/s. The low velocity values in the channel are driven by the operation of the kinetic water turbines in real-world conditions. When describing the test channel, the influence of several boundary conditions has been taken into account, such as protrusions between the measurement sections, the water level, and disturbing effects. Results for the velocity fields determined in five sections of the test open channel are given. A turbine and an electromagnetic probe were used for the experiments. A comparison between the results obtained with the two measuring instruments under the same flow conditions in the test channel is made. The results for the velocity variation in the test sections for the maximum velocity in the channel are presented. At this maximum water velocity, the test channel maintains a water level of approximately 150 mm. The experimental data is also illustrated graphically, along with the velocity fluctuations along the channel centreline. The results obtained provide an idea of the expected velocity fields in the measurement open channel and the relative magnitude of the fluctuations in the different measurement sections.

Enhanced Design Automation for Hydraulic Manifolds Produced Using Additive Manufacturing

Complex, highly functional components such as hydraulic manifolds can be produced using metal additive manufacturing (AM). The design process is a major challenge in the development of AM components that exploit this potential. Since traditional CAD systems are not made to efficiently create highly complex designs, new approaches to the design process are required. Design Automation (DA) and Knowledge-Based Engineering (KBE) are approaches that can be used to create designs and implement design changes faster and improve functionality. For the application of fluid components, KBE design workflows were developed which enable the automated generation of AM manifolds.However, these workflows have some limitations that need to be improved to provide a flexible design tool that enables users to automatically create geometries that meet all requirements. This paper shows how the workflows have been improved by introducing two new features. First, the object-oriented input format presents a new approach to how the information of a hydraulic circuit diagram can be processed to start the workflows. This is done through a component library that contains a selection of flow components providing all information and geometries of one component, a 3D layout assembly to orient the relevant components in space, and a connectivity matrix that defines the connection through flow channels for the manifold. Second, the bending radius constraint allows users to define a radius that the centerline of a flow channel should not undergo along the whole path. The new features are presented in detail in this paper. Further, the advantages are shown and compared to the previously published workflows in a case study. This work lays the foundation for future work that has the aim to fully automate the design process by only taking a hydraulic circuit diagram as an input and providing all required manufacturing files as an output.