Shape Changes Research Articles

Analysis of prefabricated myofunctional appliances with different overjet and bumper designs: a three-dimensional finite element analysis

BackgroundPrefabricated myofunctional appliance can guide tooth eruption, improve dentition alignment, correct myofunctional disorders and harmful oral habits. However, its application to skeletal discrepancy may result in unsatisfactory tooth inclination. This study aimed to construct a novel appliance with overjet design to avoid this side effect and investigated its shape and mechanical changes under occlusion using three-dimensional finite element method.MethodsWe established three samples of prefabricated myofunctional appliances. The first one was edge to edge without overjet, and the outer shield of both jaws were flattened. The second one was 3 mm overjet with stepped the outer shield. The last one was 3 mm overjet, and the outer shield of both jaws were flatted, which meant the front wall of lower jaw was strengthened with bumper, termed as lower bumper. A complete dentition model was applied to the study. 150 N occlusal force was applied to each type of appliance and the deformation displacement and the changes in stress was recorded.ResultsThe deformation was significant in the incisors regions, especially in the vertical and lateral dimensions. The maximum displacements of 3 mm overjet with step shield group were 7.08 mm (vertical), 3.99 mm (lateral), and 2.90 mm (sagittal), while it decreased to 3.92 mm(vertical), 1.94 mm (lateral), and 1.55 mm (sagittal) in overjet with bumper group. Moreover, the upper molar regions exhibited higher vertical and sagittal displacement in 3 mm overjet with step shield group, which were 3.03 mm (vertical) and 1.99 mm (sagittal), and the bumper design could decrease the maximum displacement to 1.72 mm (vertical) and 0.72 mm (sagittal). In addition, the Von Mises stress of appliances was analyzed, and results indicated that 3 mm overjet with step shield generated higher stress than other groups, with the maximum Von Mises stress was 0.9387 MP, which were 0.5858 and 0.5657 MP in edge to edge group and 3 mm overjet with lower bumper group, respectively.ConclusionThe prefabricated myofunctional appliances may cause deformation during occlusion. Compared to step shield group, the application of lower bumper exhibited better resistance to occlusal force.

Topological analysis of 3D digital ovules identifies cellular patterns associated with ovule shape diversity.

Tissue morphogenesis remains poorly understood. In plants, a central problem is how the 3D cellular architecture of a developing organ contributes to its final shape. We address this question through a comparative analysis of ovule morphogenesis, taking advantage of the diversity in ovule shape across angiosperms. Here, we provide a 3D digital atlas of Cardamine hirsuta ovule development at single cell resolution and compare it to an equivalent atlas of Arabidopsis thaliana. We introduce nerve-based topological analysis as a tool for unbiased detection of differences in cellular architectures and corroborate identified topological differences between two homologous tissues by comparative morphometrics and visual inspection. We find that differences in topology, cell volume variation and tissue growth patterns in the sheet-like integuments and the bulbous chalaza, are associated with differences in ovule curvature. In contrast, the radialized, conical ovule primordia and nucelli exhibit similar shapes despite differences in internal cellular topology and tissue growth patterns. Our results support the notion that the structural organization of a tissue is associated with its susceptibility to shape changes during evolutionary shifts in 3D cellular architecture.

Neuronal LRP4 directs the development, maturation, and cytoskeletal organization of Drosophila peripheral synapses.

Tissue morphogenesis remains poorly understood. In plants, a central problem is how the 3D cellular architecture of a developing organ contributes to its final shape. We address this question through a comparative analysis of ovule morphogenesis, taking advantage of the diversity in ovule shape across angiosperms. Here, we provide a 3D digital atlas of Cardamine hirsuta ovule development at single cell resolution and compare it to an equivalent atlas of Arabidopsis thaliana. We introduce nerve-based topological analysis as a tool for unbiased detection of differences in cellular architectures and corroborate identified topological differences between two homologous tissues by comparative morphometrics and visual inspection. We find that differences in topology, cell volume variation and tissue growth patterns in the sheet-like integuments and the bulbous chalaza, are associated with differences in ovule curvature. In contrast, the radialized, conical ovule primordia and nucelli exhibit similar shapes despite differences in internal cellular topology and tissue growth patterns. Our results support the notion that the structural organization of a tissue is associated with its susceptibility to shape changes during evolutionary shifts in 3D cellular architecture.

Programmable, Self-Healable, and Photochromic Liquid Crystal Elastomers Based on Dynamic Hindered Urea Bonds for Biomimetic Flowers.

Recently, researchers have been exploring the use of dynamic covalent bonds (DCBs) in the construction of exchangeable liquid crystal elastomers (LCEs) for biomimetic actuators and devices. However, a significant challenge remains in achieving LCEs with both excellent dynamic properties and superior mechanical strength and stability. In this study, a diacrylate-functionalized monomer containing dynamic hindered urea bonds (DA-HUB) is employed to prepare exchangeable LCEs through a self-catalytic Michael addition reaction. By incorporating DA-HUB, the LCE system benefits from DCBs and hydrogen bonding, leading to materials with high mechanical strength and a range of dynamic properties such as programmability, self-healing, and recyclability. Leveraging these characteristics, bilayer LCE actuators with controlled reversible thermal deformation and outstanding dimensional stability are successfully fabricated using a simple welding method. Moreover, a biomimetic triangular plum, inspired by the blooming of flowers, is created to showcase reversible color and shape changes triggered by light and heat. This innovative approach opens new possibilities for the development of biomimetic and smart actuators and devices with multiple functionalities.

Synthetic silica fibers of different length, diameter and shape: synthesis and interaction with rat (NR8383) and human (THP-1) macrophages in vitro, including chemotaxis and gene expression profile

BackgroundInhalation of biopersistent fibers like asbestos can cause strong chronic inflammatory effects, often resulting in fibrosis or even cancer. The interplay between fiber shape, fiber size and the resulting biological effects is still poorly understood due to the lack of reference materials.ResultsWe investigated how length, diameter, aspect ratio, and shape of synthetic silica fibers influence inflammatory effects at doses up to 250 µg cm-2. Silica nanofibers were prepared with different diameter and shape. Straight (length ca. 6 to 8 µm, thickness ca. 0.25 to 0.35 µm, aspect ratio ca. 17:1 to 32:1) and curly fibers (length ca. 9 µm, thickness ca. 0.13 µm, radius of curvature ca. 0.5 µm, aspect ratio ca. 70:1) were dispersed in water with no apparent change in the fiber shape during up to 28 days. Upon immersion in aqueous saline (DPBS), the fibers released about 5 wt% silica after 7 days irrespectively of their shape. The uptake of the fibers by macrophages (human THP-1 and rat NR8383) was studied by scanning electron microscopy and confocal laser scanning microscopy. Some fibers were completely taken up whereas others were only partially internalized, leading to visual damage of the cell wall. The biological effects were assessed by determining cell toxicity, particle-induced chemotaxis, and the induction of gene expression of inflammatory mediators.ConclusionsStraight fibers were only slightly cytotoxic and caused weak cell migration, regardless of their thickness, while the curly fibers were more toxic and caused significantly stronger chemotaxis. Curly fibers also had the strongest effect on the expression of cytokines and chemokines. This may be due to the different aspect ratio or its twisted shape.

New species of Bryophaenocladius Thienemann, 1934 (Diptera: Chironomidae) from Argentina

Three new species of Bryophaenocladius Thienemann are described and figured as male imagines: B. urbanus sp. n. from Central Argentina, and B. virgotruncatus sp. n. and B. nasus sp. n. from Argentinean Patagonia. A geometric morphometric analysis was performed to evaluate the taxonomic value of the shape of the anal point in species delimitation. The analysis involved 96 species. As a result, the Bryophaenocladius species showed significant anal point patterns of shape change, recovering three main shape types: rounded, equilateral triangle-shaped, and isosceles triangle-shaped. An identification key of the Bryophaenocladius species from the Neotropical region is provided.

Gradients of properties increase the morphing and stiffening performance of bioinspired synthetic fin rays

Abstract State-of-the-art morphing materials are either very compliant to achieve large shape changes (flexible metamaterials, compliant mechanisms, hydrogels), or very stiff but with infinitesimal changes in shape that require large actuation forces (metallic or composite panels with piezoelectric actuation). Morphing efficiency and structural stiffness are therefore mutually exclusive properties in current engineering morphing materials, which limits the range of their applicability. Interestingly, natural fish fins do not contain muscles, yet they can morph to large amplitudes with minimal muscular actuation forces from the base while producing large hydrodynamic forces without collapsing. This sophisticated mechanical response has already inspired several synthetic fin rays with various applications. However, most “synthetic” fin rays have only considered uniform properties and structures along the rays while in natural fin rays, gradients of properties are prominent. In this study, we designed, modeled, fabricated and tested synthetic fin rays with bioinspired gradients of properties. The rays were composed of two hemitrichs made of a stiff polymer, joined by a much softer core region made of elastomeric ligaments. Using combinations of experiments and nonlinear mechanical models, we found that gradients in both the core region and hemitrichs can increase the morphing and stiffening response of individual rays. Introducing a positive gradient of ligament density in the core region (the density of ligament increases towards the tip of the ray) decreased the actuation force required for morphing and increased overall flexural stiffness. Introducing a gradient of property in the hemitrichs, by tapering them, produced morphing deformations that were distributed over long distances along the length of the ray. These new insights on the interplay between material architecture and properties in nonlinear regimes of deformation can improve the designs of morphing structures that combine high morphing efficiency and high stiffness from external forces, with potential applications in aerospace or robotics.

Comparison of Newtonian and glycerol-water solution-based SiO2 nanofluid droplets impacting on heated spherical surfaces

The dynamic interactions of liquid droplets with heated spherical particles, relevant across various scientific and engineering disciplines, display intriguing collision behaviors whose principles are yet to be fully deciphered. This investigation utilizes high-speed photography to explore the wetting and non-wetting responses of different Newtonian and glycerol-water solution-based SiO2 nanofluid droplets upon contact with heated particles. Findings indicate that nanofluid droplets disrupt the thermal field and modify the surface morphology of particles more extensively under wetting than non-wetting conditions. Wetting conditions lead to significant alterations in the liquid film thickness and notable velocity field disruptions for droplets of deionized water and glycerol solution. Conversely, in the non-wetting phase, droplets nearing full rebound cause less disturbance to the velocity field, a behavior consistent across all fluid types and particle temperatures. The shape changes nanofluid droplets undergo when rebounding and separating from the particle surface are similar to those seen in glycerol solution and water droplets. Droplets in the breakup-rebound phase experience shorter contact times than those merely rebounding. A phase diagram is presented, detailing wetting (receding-deposition and boiling-breakup) and non-wetting (rebound and breakup-rebound) actions. An increase in the Weber number necessitates a higher particle temperature for the transition from rebound to breakup-rebound, which corroborates with theoretical insights. Furthermore, droplets achieve their maximum spreading area during the boiling-breakup mode.

Development of smart materials with versatile bending capabilities using microcellular foaming process: influence of foaming and desorption time

Abstract Herein, a smart material with versatile bending capability is developed using a microcellular foaming process (MCPs). In contrast to previous hydrogel-based approaches, the bi-layered smart material is fabricated using typical thermoplastics, polyethylene terephthalate glycol (PETG) and polymethyl methacrylate (PMMA), to achieve shape deformation in response to thermal stimuli. Further, the theoretical model for bi-layered smart materials based on the modified Timoshenko’s model is employed to predict and comprehend this thermal response phenomenon. Due to the distinct foaming characteristics of the two polymers, a reversal in the bending direction is achieved by manipulating the foaming and desorption time. The length variation after foaming differs depending on the desorption time for each polymer. PMMA decreases in length after foaming, measuring 56.25 mm at a desorption time of 40 min and 53.16 mm at 80 min. On the other hand, PETG shows an increase in length after foaming, measuring 53.33 mm at 40 min and 58.25 mm at 80 min. Consequently, when the two polymers are bonded and foamed, bending occurs depending on the desorption time, and a reversal in the bending direction is observed at the critical desorption time of around 60 min. Based on this result, the folding direction of a five-leafed flower-shaped object is successfully altered under thermal stimuli. This innovative approach extends the category of smart materials beyond the hydrogels and showcases the potential of the MCPs for the creation of smart materials for various applications that require versatile shape changes in response to temperature.

ANALYSIS OF THE FORM AND SURFACE OF DENTAL IMPLANTS

The aim of the work – to study the peculiarities of the shape and surface relief of the main types of dental implants. Materials and methods. 12 dental implants used in the medical practice of Ukrainian dental clinics were studied. The study of the shape and surface relief of the implants was carried out using a scanning electron microscope GSM-649 (Japan). Results. All implants in the apical part have the shape of a cone with threads and cutting grooves. The thread with a large profile is located in the apical part of the implant, has an average pitch of turns of 1.1±0.05 mm and a profile height of 0.3±0.02 mm. The thread with a small profile is located in the part of the implant near the neck, has a pitch of 0.4±0.02 mm and a profile height of 0.1±0.02 mm. The thread pitch of implants with a single profile is 0.8±0.05 mm, and the height of the profile is 0.2±0.01 mm. Threads with a triangular profile have a profile angle of 50.0±2.9 degrees. The highest roughness is the surface of the top of the fine profile thread with the height of micro-uniformities from 7.0±2.2 to 36.0±8.3 μm, the smallest roughness with the height of micro-uniformities from 3.0±1.1 to 14.0±6.1 μm have surface areas in the area of the implant neck. Conclusions. 50% of the examined implants were made with two thread profiles: a large one in the apical side and a small one closer to the neck, 50% – with the same thread profile from the apical end to the neck. In most implants, the thread with a small profile is made in the form of annular grooves. The large thread of the implants had a rectangular, rounded and triangular profile with one or two steps. In some implants, as they approach the neck, the shape changes and the height of the thread profile decreases. The shape of the profile of small threads in all implants was close to rounded. The implants had different surface roughness. The highest roughness was recorded on the surface of the top of the small profile thread, and the lowest – in the area without a thread in the area of the implant neck.

An emerging role for tissue plasticity in developmental precision.

Reproducible tissue morphology is a fundamental feature of embryonic development. To ensure such robustness during tissue morphogenesis, inherent noise in biological processes must be buffered. While redundant genes, parallel signaling pathways and intricate network topologies are known to reduce noise, over the last few years, mechanical properties of tissues have been shown to play a vital role. Here, taking the example of somite shape changes, I will discuss how tissues are highly plastic in their ability to change shapes leading to increased precision and reproducibility.

Asymmetric fin shape changes swimming dynamics of ancient marine reptiles’ soft robophysical models

Animals have evolved highly effective locomotion capabilities in terrestrial, aerial, and aquatic environments. Over life’s history, mass extinctions have wiped out unique animal species with specialized adaptations, leaving paleontologists to reconstruct their locomotion through fossil analysis. Despite advancements, little is known about how extinct megafauna, such as the Ichthyosauria one of the most successful lineages of marine reptiles, utilized their varied morphologies for swimming. Traditional robotics struggle to mimic extinct locomotion effectively, but the emerging soft robotics field offers a promising alternative to overcome this challenge. This paper aims to bridge this gap by studying Mixosaurus locomotion with soft robotics, combining material modeling and biomechanics in physical experimental validation. Combining a soft body with soft pneumatic actuators, the soft robotic platform described in this study investigates the correlation between asymmetrical fins and buoyancy by recreating the pitch torque generated by extinct swimming animals. We performed a comparative analysis of thrust and torque generated by Carthorhyncus, Utatsusaurus, Mixosaurus, Guizhouichthyosaurus, and Ophthalmosaurus tail fins in a flow tank. Experimental results suggest that the pitch torque on the torso generated by hypocercal fin shapes such as found in model systems of Guizhouichthyosaurus, Mixosaurus and Utatsusaurus produce distinct ventral body pitch effects able to mitigate the animal’s non-neutral buoyancy. This body pitch control effect is particularly pronounced in Guizhouichthyosaurus, which results suggest would have been able to generate high ventral pitch torque on the torso to compensate for its positive buoyancy. By contrast, homocercal fin shapes may not have been conducive for such buoyancy compensation, leaving torso pitch control to pectoral fins, for example. Across the range of the actuation frequencies of the caudal fins tested, resulted in oscillatory modes arising, which in turn can affect the for-aft thrust generated.

The shape of fringing tidal flats in engineered estuaries

For the management of estuaries and the preservation of tidal flats it is crucial to understand the tidal flat shape and development. Previous work focused predominantly on the quasi-equilibrium shape of tidal flats along open coasts with a dominant cross-shore flow and wave exposure. This paper evaluates the shape of fringing tidal flats in engineered estuaries, where longshore velocities generally dominate. Using a long-term (20 years) topographic data set of an anthropogenically modified estuary in the Netherlands (the Western Scheldt estuary), we relate key profile shape parameters and changes over time to natural and anthropogenic processes. In an engineered estuary, the tidal flat shape depends on the estuary geometry, hydrodynamic forcings and human interventions. In contrast to open coast tidal flats, the presence of the channel and dominant longshore flow determines the available cross-shore length (accommodation space) of the tidal flat and the shape of the tidal flat. This accommodation space defines the maximum tidal flat height and opportunity for marsh development. We propose the use of the Index of Development, indicating to what extend tidal flats have space to develop. This index is not only influenced by longshore and cross-shore flow, but also (or even more) by hydraulic structures, dike realignments and channel migration. Especially the latter two strongly influence the accommodation space and thereby the maximum tidal flat height and the opportunity for marsh development. For large stretches of the Western Scheldt, the accommodation space is too small, and the majority of the tidal flats do not vertically extent to mean high water. The success of tidal flat and marsh restoration projects depends on the accommodation space.

The where, when, and how of ooid formation: What ooids tell us about ancient seawater chemistry

Ooids are a common constituent of carbonate rock throughout the last 3.2 billion years. The chemical and physical characteristics of ooids record essential details of the carbonate chemistry and hydrodynamic conditions of their depositional environment. As a result, ooids may be a powerful tool for reconstructing Earth's ancient climates and environments. However, lack of constraints on fundamental aspects of ooid formation, such as the role of abrasion, underscores the potential for additional discoveries utilizing ooids as paleoenvironmental proxies. Here, we use three-dimensional models built by serially grinding and imaging ooids to show how ooid shape changes during growth. We find that ooid abrasion plays only a small role in the formation of ooids, even in giant ooids, where the mass should cause abrasion to be most intense. A lack of abrasion during ooid formation suggests a greater sensitivity of ooid distribution and size to the chemistry of depositional environments. This insight enables us to harmonize our understanding of ooid formation with longstanding questions regarding their spatial and temporal distribution, as well as size variations. With a new database of ooid occurrences, we analyze the influence of seawater chemistry, carbonate shelf area, and evolutionary developments on ooid abundance in the Modern, Last Glacial Period, and throughout the Phanerozoic. Finally, we leverage our new understanding of ooid growth to show how ooid size, including giant ooids, can shed light on relative changes in alkalinity throughout the Phanerozoic.

In-situ evidence for the existence of surface films in electrochemical machining of copper in nitrate electrolytes

This contribution analyzes the electrochemical etching of copper in a sodium nitrate electrolyte using in-situ Raman spectroscopy. Experiments were conducted in a specially designed process chamber at voltages below, at, and above the limiting current plateau. Below the plateau, a Raman peak at 1050 cm–1 is detected, which is attributed to the symmetrical nitrate ion. However, the line shape changes at and above the plateau. Detailed line shape analysis indicates the presence of a copper nitrate surface film by ex-situ comparison with copper nitrate solutions. In addition, the conductivity and pH of copper nitrate solutions were determined. A 5 M copper nitrate solution exhibits a low conductivity of 55 mS cm–1 and a pH close to 0. A significant influence, especially of the low pH, on the surface structure and therefore on the etching mechanism is assumed.

A new view of territoriality in large eagles: the territory pre‐exists regardless of their occupants

AbstractKnowledge of vertebrate territoriality and spatial use is a topic of great interest in the study of animal behaviour and conservation biology. Investigating the plasticity of territory boundaries, the shape of territories and how territories can be modified depending on their owners is important to deepen our knowledge of the behaviour of territorial species. We analysed the variation and tested the similarity of the distribution area of individuals from the same territory between 2015 and 2021, using data from 51 Bonelli's eagles (Aquila fasciata) from 22 different territories, tagged with GPS/GSM transmitters in eastern Spain. We calculated the percentage of overlap between the territories of the same individual in different years using the 95% kernel density estimator. We also analysed the changes in territory size and shape following the replacement of territory owners either by a single individual or by the whole pair. Our results show that territories retain the same shape and extent regardless of the occupying members, and that their boundaries change little over time. Identifying and maintaining large eagle territories, regardless of their owners, is therefore key to ensuring the long‐term recovery of these threatened species.

Incorporation of efavirenz inclusion complex In Dissolvable Microneedle for enhanced effectiveness of intravaginal drug delivery: A proof of concept study

Efavirenz (EFV) is one of the first line treatments of HIV infection. EFV is one of non-nucleoside reverse transcriptase inhibitors (NNRTIs) that can inhibit the responsible of reverse transcriptase enzyme for HIV replication. In oral administration, EFV exhibits low bioavailability (30–56 %) problem owing to its poor solubility (0.9 μg/mL). In this research, the poor solubility was overcome by formulating EFV as a complex inclusion (IC)with β-cyclodextrin (β-CD). Furthermore, considering the benefits of vaginal delivery, IC was further incorporated into dissolving microneedle systems (DMN) using polyvinyl alcohol (PVA) and polyvinyl pyrrolidone (PVP) as biocompatible and biodegradable polymes. The results showed that EFV successfully formed IC by the change of the molecular shape with β-CD polymer, confirmed by FTIR and XRD. Importantly, the results showed that the formulation did not cause lysis and irritation on erythrocytes and blood vessels, showing the safety of this approach. Following its incorporation into DMN, IC-DMN could permeate the skin ex vivo as 78.70 ± 14.22 μg/cm3, which was about 3-times higher compared to DMN containing pure EFV and patch control. The in vivo pharmacokinetic study showed that the maximum plasma concentration of IC-DMN was 13.74 ± 2.48 μg/cm3, EFV-oral 6.27 ± 1,13 μg/cm3, vaginal gel 14.83 ± 3.65 μg/cm3. AUC values for each treatment was 147.33 ± 26.62 h μg/mL, 22.33 ± 4.03 h μg/mL, 63.33 ± 11.44 h μg/mL, respectively, indicating that the purpose of this study which was to increase the bioavailability of EFV was succefully achieved. Therefore, this combibation approach could be new alternative to HIV treatment using EFV in woman.

Changes in Cephalic Index and Head circumference of Igbo Children and Adolescents in a Nigerian Population

Background: The cephalic index and head circumference are important anthropometric parameters that can provide insights into the physical characteristics and growth patterns of populations. There is dearth of data on Cephalic Index and Head circumference of Igbo Children and Adolescents. Method: This study examined 725 Igbo children and adolescents aged 5 to 19 years in Enugu, South-eastern Nigeria, using a cross-sectional approach. Results: The majority of participants exhibited mesocephalic head shape (43.2%), with brachycephalic and dolichocephalic shapes observed in 32.7% and 14.2% of the population, respectively. Mean head circumference increased with age in both sexes. Cephalic indices in boys under 12 and girls under 15 were below 80 but increased above these ages. Changes in head shape, potentially towards brachycephalization, were noted as children grew. Significant correlations were found between head circumference and cephalic index with age, height, weight, and body mass index, suggesting their relevance in forensic and anthropological investigations. Conclusion: Our results indicate diversity in head shapes and sizes, with mesocephalic heads being most common. As age increases, head circumference also tends to increase, and changes in head shape towards brachycephalization was observed. These findings underscore the importance of understanding anthropometric variations in different populations and suggest avenues for further research, particularly longitudinal studies, to explore the factors influencing these patterns.

Matrix‐phase material selection for shape memory polymer composites: A comparative analysis of multi‐criteria decision‐making

AbstractIn the present study, the selection of suitable shape memory polymers (SMPs) to be used as the matrix‐phase material with various (In)organic filler materials to achieve the required optimum multi‐stimuli response in shape memory polymer composites (SMPC) systems is analyzed. The selection of these materials is based on their mechanical and physical properties as well as other underlying factors such as cost, availability, shape recovery rate, and aesthetic characteristics. In this study, the entropy method was applied to estimate the weightages of the various criteria while the gray relation analysis (GRA) and the technique for order preference by similarity to ideal solution (TOPSIS). Multi‐criteria decision‐making (MCDM) approaches have been used to rank the suitable matrix‐phase polymer materials for manufacturing shape memory polymer composites (SMPC) system. A total of eight alternative SMP matrix‐phase materials based on a set of nine criteria were analyzed and ranked. The proposed methodology and the result obtained thereof have been illustrated in detail. The results obtained from TOPSIS and GRA methods have been compared to conclude the effects of the material properties on the ranking and the selection of the SMP materials. Among all the eight alternatives considered, thermoplastic polyurethane (TPU) was found to be the best material in both the MCDM methods. The material cost, resistivity, % elongation, and hydrophobicity present the most influencing properties on the SMP material selection, whereas density presents no effect on the SMP matrix material selection. The robustness of the results for the comparative analysis was verified using TOPSIS methodology to validate its reliability. It was revealed that the TPU, polycarbonate, polypropylene, and epoxy‐resin/poly(lactic acid) are the most dominant matrix‐phase SMP material alternatives when a deviation in the entropy weights of the primary evaluation criteria is applied. The novelty of this study is the exploration and application of statistical MCDM methods of engineering material selection problems based on a set of decision criteria, which can be time‐consuming and costly while using experimental analysis methods.Highlights SMPCs are applicable engineering materials thus making their research viable. SMPC systems can undergo various shape changes under external stimuli. Selection of matrix‐phase polymer is critical in achieving desired objectives. GRA and TOPSIS MCDM approaches have been applied in the selection process. TPU was found as the best material in both methods.

Shape isomers: status and perspectives across the nuclear chart

AbstractThe paper reviews the searches for shape isomers, which are “extreme” example of shape-coexistence phenomena in nuclei. They may appear when highly deformed structures, well localized in the nuclear Potential Energy Surface (PES) in the deformation space, undergo a significant change in shape to match the final state shape, thus leading to a substantially hindered $$\gamma$$ γ decay. This is in sharp contrast to the vast majority of shape-coexistence phenomena, where significant mixing in the initial and final state wave functions is found. So far, the most spectacular examples of shape isomerism are known in fissioning systems in the actinides, although only scarce experimental information is available from experiments conducted more than 20 years ago. Searches in lighter mass regions, guided by theory predictions based on different approaches and experimental investigations on superdeformed systems, are also presented. They point to $$^{64,66}$$ 64 , 66 Ni as additional examples of prolate deformed shape-isomer-like structures, although with much reduced hindrance with respect to the actinides. Their origin is strictly related to the action of the monopole component of the tensor force of the nucleon-nucleon interaction, which is expected to favor the appearance of deep secondary minima also in the PES of Sn nuclei with masses 112–118. Perspectives in current searches of shape isomerism with modern detection systems, in the actinides regions and in lighter masses, are discussed.