Changes In Mechanical Properties Research Articles

Grain-Refinement by MDFing under Decreasing-Temperature Conditions Followed by Room-Temperature MDFing of AZX611Mg Alloy and Change in Mechanical Properties

Grain-Refinement by MDFing under Decreasing-Temperature Conditions Followed by Room-Temperature MDFing of AZX611Mg Alloy and Change in Mechanical Properties

Comparative effects of glazing versus polishing on mechanical, optical, and surface properties of zirconia ceramics with different translucencies.

This study compared the effects of glazing versus polishing on mechanical, optical, and surface properties of zirconia ceramics with different translucencies. In this in vitro study, 120 bar-shaped specimens (25 × 4 × 1.2 mm) were fabricated from three different types of zirconia with different translucencies (n = 40, DD Bio ZW, ZX2, and Cube X2). After sintering, each zirconia group was randomly divided into five subgroups of control (glazing), glazing + bur abrasion, glazing + bur abrasion + polishing with EVE Diacera® kit, glazing + bur abrasion + reglazing, and glazing + bur abrasion + polishing with EVE Diacera® kit + reglazing. The specimens underwent surface roughness, hardness, flexural strength, and translucency tests, as well as X-ray diffraction (XRD) and scanning electron microscopy (SEM) for assessment of surface topography. Data were analyzed by one-way analysis of variance, Tukey test, and Pearson test (α = .05). Flexural strength, surface hardness, and translucency were significantly correlated with zirconia type. ZW zirconia had significantly higher flexural strength and surface hardness and significantly lower translucency than Cube X2 and ZX2 (p < .001). Surface roughness had no significant correlation with zirconia type (p = .274). Polishing created the smoothest, and bur abrasion created the roughest surface (p < .001). Flexural strength and hardness in most experimental groups were significantly lower than in the control group (p < .001). Translucency was not significantly different in bur abrasion and polishing groups, compared with the control group; however, reglazing significantly increased the translucency (p < .001). SEM micrographs confirmed the surface roughness results. XRD showed monoclinic phase only in reglazed groups. Of different surface treatments, polishing improved the surface properties and caused the smallest change in mechanical properties of zirconia with different translucencies.

Extracellular matrix stiffness mediates insulin secretion in pancreatic islets via mechanosensitive Piezo1 channel regulated Ca2+ dynamics

The pancreatic islet is surrounded by ECM that provides both biochemical and mechanical cues to the islet β-cell to regulate cell survival and insulin secretion. Changes in ECM composition and mechanical properties drive β-cell dysfunction in many pancreatic diseases. While several studies have characterized changes in islet insulin secretion with changes in substrate stiffness, little is known about the mechanotransduction signaling driving altered islet function in response to mechanical cues. We hypothesized that increasing matrix stiffness will lead to insulin secretion dysfunction by opening the mechanosensitive ion channel Piezo1 and disrupting intracellular Ca2+ dynamics in mouse and human islets. To test our hypothesis, mouse and human cadaveric islets were encapsulated in a biomimetic reverse thermal gel (RTG) scaffold with tailorable stiffness that allows formation of islet focal adhesions with the scaffold and activation of Piezo1 in 3D. Our results indicate that increased scaffold stiffness causes insulin secretion dysfunction mediated by increases in Ca2+ influx and altered Ca2+ dynamics via opening of the mechanosensitive Piezo1 channel. Additionally, inhibition of Piezo1 rescued glucose-stimulated insulin secretion (GSIS) in islets in stiff scaffolds. Overall, our results emphasize the role mechanical properties of the islet microenvironment plays in regulating function. It also supports further investigation into the modulation of Piezo1 channel activity to restore islet function in diseases like type 2 diabetes (T2D) and pancreatic cancer where fibrosis of the peri-islet ECM leads to increased tissue stiffness and islet dysfunction.

Development in the Study of Mechanical Prop-erties and Damage Constitutive Models of Rub-ber-Reclaimed Concrete

Advances in rubber-reinforced concrete technology and its applications in engineering are cru-cial for the thorough recycling and safe disposal of waste tire rubber and construction debris. Rubber-reinforced concrete (RAC) is a concrete material produced by substituting some fine and coarse aggregates with waste rubber particles and recycled aggregates. The incorporation of waste rubber particles endows RAC with distinctive mechanical properties and a distinct damage constitutive model. The mechanical properties of rubber recycled concrete mainly in-clude compressive strength, tensile strength, flexural strength, and elastic modulus. Compared to traditional concrete, RAC exhibits slightly lower compressive and flexural strengths but sig-nificantly enhanced tensile strength. This is due to the changes in mechanical properties caused by the softness and elastic properties of rubber particles. In addition, the addition of rubber particles can also improve the energy absorption capacity and impact resistance of concrete. On the other hand, in order to describe the damage behavior of rubber recycled con-crete, some constitutive models were studied. Common models include linear elastic model, plastic model, and damage model. The linear elastic model is suitable for describing the be-havior of rubber recycled concrete during the elastic stage; The plastic model is suitable for describing its deformation behavior during the plastic stage; The damage model can better describe the fracture and failure behavior of rubber recycled concrete, including shear damage, tensile damage, and compression damage. Tailored to the unique characteristics of RAC, these models consider the stiffness of rubber particles and the deformation characteristics of the binding materials, enabling accurate predictions of the stress-strain behavior of RAC. In conclusion, rubber-reinforced concrete possesses excellent mechanical and durability proper-ties, which can be accurately described and predicted using appropriate constitutive models. These findings are crucial for advancing the application and development of rubber-reinforced concrete.

Large inter-individual variability in force-velocity profile changes in response to acute high-load resistance training.

While the acute effects of high-load resistance training on the force generating capacity of muscles have been widely examined, limited data exist on the relationship with the force-velocity profile (FV). Evidence suggests high sensitivity of the vertical FV profile to monitor changes in the muscle's mechanical properties according to the type of the exercise protocol. However, the interpretation of the findings seems not as straightforward. Therefore, the purpose of this study was to examine the effects of a high-load resistance training protocol on the muscle's mechanical properties during loaded jumps and on the vertical force-velocity profile (FV) in relation to maximal strength. 29 resistance-trained male (mean age±SD: 35.4 ± 7.8 years) and 29 female athletes (mean age±SD: 32.5 ± 7.0 years) participated in the study. Five-repetition maximum (5RM) in back squat, unloaded countermovement jump (CMJ) and FV profile were assessed. Loaded jumps were performed against 25, 50, 75, and 100 percent of body mass. Participants performed exercise protocols corresponding to their 5RM. Immediately after, unloaded CMJ and FV profile measurements were repeated. A significant decrease in CMJ height (∼5-6%) and in average power (∼4%) was recorded for both men and women. The FV profile did not change after the exercise protocol; however, there was a significant decrease in theoretical maximal power (from 4 to 5%) and in theoretical maximal velocity (∼3%). Maximal strength was not associated with the changes in FV profile. Findings suggest that an acute high-load exercise decreased vertical jump performance and maximal power output, but without a concomitant change in FV profile. The large interindividual variability in FV measures indicates a less straightforward connection of the applied exercise with the acute response in the FV profile, highlighting the complexity of the FV profile to monitor changes in response to an acute training load.

Lattice optimization of fiber-reinforced polymer parts fabricated by additive manufacturing: the impact of Bezier curve order on mechanical properties

Purpose Lattice structures are widely used for achieving optimal topology in additive manufacturing. However, the use of different lattices in a single design can result in stress concentrations at the transition points. This study aims to investigate the influence of Bezier curves on mechanical properties during the transformation from one lattice structure to another. It specifically focuses on the transition from a hexagonal to diamond lattice, using Bezier curves of various orders. Design/methodology/approach The curves were designed by passing them through the same control points for different orders, such as third, fifth and seventh. The samples were sliced for 3D printing, and a tensile test was conducted. Young’s modulus and energy absorption abilities were measured to compare the mechanical properties of the models created with Bezier curves for the transformation between hexagonal and diamond models. Findings The analysis revealed a gradual change in mechanical properties from the hexagonal to the diamond lattice. Moreover, different orders of Bezier curves exhibited varying mechanical properties during the transformation between the two lattices. As the order of the Bezier curve increased, the mechanical properties smoothly changed from the hexagonal to diamond lattice. This prevented stress concentrations or mechanical behavior mismatch caused by sudden deformations at the transitions between the curves used in the design. Originality/value The study’s innovative use of Bezier curves of different orders to smoothly transformation between hexagonal and diamond lattices in additive manufacturing offers a practical solution to prevent stress concentrations and mechanical inconsistencies during such design transitions.

The impact of magnesium content on lithium-magnesium alloy electrode performance with argyrodite solid electrolyte

Solid-state lithium-based batteries offer higher energy density than their Li-ion counterparts. Yet they are limited in terms of negative electrode discharge performance and require high stack pressure during operation. To circumvent these issues, we propose the use of lithium-rich magnesium alloys as suitable negative electrodes in combination with Li6PS5Cl solid-state electrolyte. We synthesise and characterise lithium-rich magnesium alloys, quantifying the changes in mechanical properties, transport, and surface chemistry that impact electrochemical performance. Increases in hardness, stiffness, adhesion, and resistance to creep are quantified by nanoindentation as a function of magnesium content. A decrease in diffusivity is quantified with 6Li pulsed field gradient nuclear magnetic resonance, and only a small increase in interfacial impedance due to the presence of magnesium is identified by electrochemical impedance spectroscopy which is correlated with x-ray photoelectron spectroscopy. The addition of magnesium aids contact retention on discharge, but this must be balanced against a decrease in lithium diffusivity. We demonstrate via electrochemical testing of symmetric cells at 2.5 MPa and 30∘C that 1% magnesium content in the alloy increases the stripping capacity compared to both pure lithium and higher magnesium content alloys by balancing these effects.

How thermal treatment affects the chemical composition and the physical, mechanical and swelling properties of Scots pine juvenile and mature wood

AbstractHigh variations in juvenile wood properties in the radial direction and its worse performance than mature wood make it less suitable for some applications and often treated as waste material. This study aimed to assess how thermal modification affects the chemical composition and the physical, mechanical and swelling properties of Scots pine juvenile and mature wood. An additional goal was to evaluate if the modification can equalise the differences in selected properties of juvenile wood to those of mature wood so that from waste material, juvenile wood can become a fully-fledged raw material for various industrial applications. Thermal treatment at 220 °C influenced wood chemical composition, degrading mainly hemicelluloses but also affecting cellulose and lignin, which resulted in a reduction of hydroxyls and carbonyl/carboxyl groups. These changes were more pronounced for mature than juvenile wood. It reduced mass loss and swelling rate, and increased swelling pressure in the tangential and radial directions to a higher degree for juvenile than mature wood. Changes in mechanical properties in compression were statistically significant only for mature wood, while wood hardness remained unaffected. Although the applied heat treatment improved the performance of juvenile wood by reducing its swelling rate, it did not equalise the examined properties between juvenile and mature wood. Since higher juvenile wood proportion is expected in the wood supply from the future intensively managed forests, there is still a need to find suitable modification methods or better processing techniques so that instead of being thrown away as waste, it could be used broadly in various industrial applications.

The study of degradation and mechanical properties of poly(lactic) acid (PLA) based 3D printed filament

Abstract Additive manufacturing, commonly known as 3D printing technology, has become one of the mainstream processes in the manufacturing industry due to its advantages over conventional manufacturing, which have piqued the public's interest. This study aims to focus on the influence of thermal conditions on crystallization towards mechanical properties of 3D printed poly(lactic) acid (PLA) degradation samples with 100% infill. As for the degradation profile, the highest weight loss recorded by the samples was 0.7%, observed in samples buried in soil with an abiotic medium for one month. The exposure of degraded samples to high temperature during drying affected their crystallinity, resulting in significant changes in strains, particularly between week 1 and week 2, where strains dropped significantly from 7.33% to 4.28%, respectively. In conclusion, it has been demonstrated that degradation for PLA material still can occur in an abiotic medium, albeit at a slower rate compared to a biotic medium due to the presence of additional microorganisms and bacteria. Besides, the post-heat treatment process on PLA degradation samples affects their crystalline structure, resulting in significant changes in mechanical properties, particularly especially strains. Therefore, it can be concluded that different materials exhibit distinct mechanical properties.

Multi-Scale Traditional and Non-Traditional Machining of Bulk Metallic Glasses (BMGs)—Review of Challenges, Recent Advances, and Future Directions

Bulk metallic glasses (BMGs) are growing in popularity prominently due to their potential in micro-electromechanical systems (MEMSs) and aerospace applications. BMGs have unique mechanical properties, i.e., high strength, hardness, modulus of elasticity, and wear resistance, due to their disordered atomic structure. Due to their unique mechanical properties and amorphous structures, machining of BMGs remains a challenge. This paper aims to carry out a detailed literature review on various aspects of the machining of bulk metallic glasses using both conventional and non-conventional processes, including experimental approaches, modeling, statistical findings, challenges, and guidelines for machining this difficult-to-machine material. Conventional machining processes were found to be challenging for machining bulk metallic glasses due to their high hardness, brittleness, and tendency to convert their amorphous structure into a crystalline structure, especially at the machined surface and sub-surface. Although their high electrical conductivity makes them suitable for machining by non-conventional processes, they impose new challenges such as heat-affected zones and crystallization. Therefore, the successful machining of BMGs requires more in-depth analysis of cutting forces, tool wear, burr formation, surface finish, recast layers or heat-affected zones, crystallization, and mechanical property changes among different varieties of BMGs. This review paper provides guidelines emerging from in-depth analysis of previous studies, as well as offering directions for future research in the machining of BMGs.

Investigating the effect of welding tool length on mechanical strength of welded metallic matrix by molecular dynamics simulation

The welding process and the properties of welding instruments may improve the mechanical performance of an item. One of these properties is the length of the welding tool. This approach has a substantial effect on the mechanical strength of the metallic matrix. The current study used molecular dynamics modeling and LAMMPS software to evaluate the effect of welding tool length on the mechanical properties of a welded Cu–Ag metallic matrix. This simulation makes use of the Lennard-Jones potential function and the embedded atom model. First, the equilibrium phase of modeled samples was verified by changing the computation of kinetic and total energies. Next, the mechanical properties of the welded matrix were studied using the stated Young's modulus and ultimate strength. The stress-strain curve of samples demonstrated that the mechanical strength of atomic samples increased as the length of the welding tool (penetration depth) increased. Numerically, by increasing the tool penetration depth of Fe tools from 2 Å to 8 Å, Young's modulus and ultimate strength of the matrixes sample increase from 34.360 GPa to 1390.84 MPa to 38.44 GPa and 1510 MPa, respectively. This suggested that the length of the Fe welding tool significantly affected the mechanical properties of the welded metallic matrix. The longer the length of Fe welding tools, the more particles were involved, and consequently, more bonds were formed among the particles. Bonding among the particles caused changes in mechanical properties, such as greater ultimate strength. This method can optimize mechanical structures and be useful in various industries.

Mechanical Assessment in Atherosclerosis Based on Photoacoustic Viscoelasticity Imaging

Early identification of vulnerable plaques is a major challenge in diagnosis and assessment of atherosclerosis. In atherosclerotic plaque development, the proportion change in components caused plaque mechanical property change and induced plaque rupture. In this paper, a photoacoustic viscoelasticity imaging (PAVEI) technique was proposed to measure the viscosity–elasticity ratio of atherosclerotic plaque and evaluated for the potential in characterizing vulnerable plaques. Apolipoprotein E-knockout mice fed with a high-fat/high-cholesterol diet were chosen as the atherosclerotic model. Plaque component phantoms were examined to demonstrate the high efficiency of PAVEI in detecting the proportion change in components compared to single elasticity or viscosity detection. Finally, atherosclerotic plaques from mice aortas at different stages were imaged by PAVEI, which provided an insight into the compositional and functional characterization of vulnerability plaques and suggested its potential applications in the identification of high-risk plaques.

Study of Surface Chemistry, Temperature and Strain Rate on the Tensile Properties of Monolayer Graphene Oxide

The mechanical properties of graphene oxide (GO) during tensile fracture were studied using molecular dynamics methods, and the influence of hydroxyl and epoxy groups on the mechanical properties of GO was explored. In addition, the changes in mechanical properties of GO under different temperatures and strain rates were studied to gain a deeper understanding of its mechanical behavior. The results indicate that hydroxyl and epoxy groups have a significant influence on the elastic modulus, ultimate stress, and ultimate strain of GO. The presence of hydroxyl and epoxy groups can alter the molecular structure of GO, thereby affecting its ultimate stress and strain. When the number of hydroxyl groups is 16 and the number of epoxy groups is 20, the ultimate stress decreases by about 31% and the elastic modulus decreases by about 20%. The variation of elastic modulus, ultimate stress, and ultimate strain of GO with temperature was studied at three temperatures: 300[Formula: see text]K, 500[Formula: see text]K, and 800[Formula: see text]K. As the temperature increases, the amplitude of atomic vibration increases and internal defects and cracks in GO continue to form and expand. At the same time, its coefficient of thermal expansion also increases, causing deformation and loosening of the crystal structure, resulting in a decrease of about 10% in the ultimate stress of GO, and a slight decrease in the ultimate strain and elastic modulus. Finally, the influence of different strain rates on the mechanical properties of GO was studied. As the strain rate increases, the intermolecular interactions within GO are rapidly altered, and the previously loose structure gradually becomes tightly ordered, resulting in an increasing trend in the elastic modulus, ultimate stress, and ultimate strain of GO.

Impact of relative humidity variations on Carrara marble mechanical properties investigated by nonlinear resonant ultrasound spectroscopy

Like many other stones, marble mechanical properties can be significantly changed in presence of water. Water most often induces a weakening which can lead to marble degradation when coupled to temperature variations. Yet, marble artefacts are more frequently subjected to relative humidity (RH) variations than episodes of water imbibition and/or drastic temperature variations. Thus, one could wonder how do variations of RH alone impact marble mechanical state. In this study, Carrara Gioia marble samples are subjected to adsorption-desorption cycles. They were previously thermally-damaged between 40 and 105 °C, and their microstructure was characterized for each heating temperature. The evolution of their mechanical properties is monitored non-destructively with two parameters measured by Nonlinear Resonant Ultrasound Spectroscopy. The resonant frequency decreases weakly with increasing RH, indicating a diminution in sample stiffness due to low moisture-induced softening. The nonlinear parameter increases strongly, probably due to higher capillary pressure associated to a capillary condensation increase with RH. However, these phenomena are reversible: during adsorption-desorption cycling both parameters remain quite constant for a given RH. Therefore, while a RH increase impacts the mechanical properties of Carrara marble, adsorption-desorption cycling shows a reversible behavior which does not induce any permanent change in mechanical properties.

Change of Mechanical Properties of e-PTFE Support by Electrochemical Degradation in Polymer Electrolyte Membrane Fuel Cell

Change of Mechanical Properties of e-PTFE Support by Electrochemical Degradation in Polymer Electrolyte Membrane Fuel Cell

Study on Microscopic Characteristics and Rock Mechanical Properties of Tight Sandstone after Acidification–Supercritical CO2 Composite Action: Case Study from Xujiahe Formation, China

Acidified CO2 fracturing is a viable method for increasing production in deep, tight sandstone reservoirs. However, the potential mechanism of changes in pore structure and mechanical properties of sandstone under acidified CO2 supercritical composite is not clear. Understanding this mechanism is important for the study of crack initiation and extension in tight sandstone reservoirs. This study utilizes sandstone samples from the Xujiahe Formation reservoir in Rongchang District as experimental specimens. The primary focus is to analyze the changes in pore structure and mechanical properties of these samples after acidification–supercritical CO2 composite action. Nuclear magnetic resonance (NMR) and uniaxial compression tests are employed as the main investigative techniques. The results show that there was a physicochemical synergy between the acidification–supercritical CO2 composite effect; the crack initial stress, damage stress, and peak stress of the sandstone after 16 MPa supercritical CO2 acidification treatment were reduced by 20%, 49.5%, and 49.8%, respectively; the crack volumetric strain accelerated and the sandstone evolved from brittle to ductile damage; and the larger pore space and microcracks of the sandstone increased significantly after the treatment, which can be attributed to the gradual dissolution of intergranular cement leading to the formation of new pores connected to the existing pore network. The change mechanism of sandstone after acidification–supercritical CO2 compound treatment is also proposed.

Utilizing decommissioned windmill blades as reinforcement or filler for biocomposites

Decommissioned or damaged windmill blades and other wastes have limited applications and are generally disposed into landfills or incinerated. Increasing generation of wind energy will also lead to increase in blades available for disposal. It is estimated that more than 800,000 tons of blades will be available annually for disposal from 2050. Blades contain glass, carbon, resins and other valuable materials and hence it is prudent to develop methods to reuse or recycle the blades. In this study, we have used windmill blade waste (WBW) as reinforcement for polypropylene (PP) and also as filler/additive for coir-WBW-PP hybrid composites. Various proportions of the components were made into composites and studied for the changes in mechanical, acoustic, thermal and noise insulation properties. Tensile strength did not show major increase in properties whereas 70/30 WBW/PP composites had highest flexural strength and modulus. Addition of WBW considerably increased both the tensile and flexural properties of the hybrid composites with up to 180% increase in flexural strength and 173% increase in modulus. Similarly, hybrid composites had better thermal conductivity and the composites containing 80% WBW and 20% PP had the highest thermal conductivity. Coir improved the acoustic sorption due to the presence of pores and voids in the composites whereas WBW acts as filler and decreased the sound sorption. WBW can be effectively used as reinforcement or filler for PP based composites.

Microstructural changes induced in advanced tungsten grades under high temperature neutron irradiation

Recent studies addressing the change of mechanical properties after high temperature irradiation of tungsten have reported substantial increase of the ductile to brittle transition temperature as well as increase of the hardness. In this work, we performed microstructural analysis by means of transmission electron microscopy (TEM) on various tungsten grades earlier exposed to high temperature neutron irradiation at 1200 °C up to 1 dpa. The latter corresponds to the expected irradiation temperature on the surface of a tungsten monoblock during the steady state operation in ITER. TEM was applied to five tungsten (W) materials including ITER specification pure W and precipitate strengthened W alloys. The analysis of TEM data coupled with its discussion led to a number of important conclusions regarding the damage induced at 1200 °C neutron irradiation such as: (i) weak effect of recrystallization on the accumulation of the lattice damage; (ii) promising results on the tolerance of damage accumulation in W-Y2O3 grade and (iii) internal oxidation of TiC particles which may contribute to the huge increase of the irradiation induced hardening.

The ANALYSIS of the MECHANICAL PROPERTIES of REGIONAL PIPELINES

Piston pumps and compressors are widely used for exploration and transportation of oil and gas. Piston machines are heavy-duty systems that are still failure prone due to high stresses and wear proses. Increasing the efficiency and durability of the piston compressors, pumps, internal combustion engines, etc. directly depends on the correct calculations and designing of these elements. Using ANSYS software, simulation and stress analysis are performed on the basis of the 405GP15/70 and ARIEL heavy-duty balanced opposed piston compressors used in the Caspian Sea-Black Sea Region. During working of the machines and equipment a number of the processes interconnected and causing each other are proceeds (dynamic processes, wear of the interfaced details, change of mechanical properties of materials, etc.). Improvement of modelling of technical condition of cars and mechanisms on a multicriteria basis is one of the actual directions of modern engineering science. The improvement of methods of modelling of change of technical conditions of the piston mechanisms taking into account interrelation of dynamic characteristics, the wear interfaced details and the diagnosed mechanical parameters considered in this article. By observing the analysis results, we can decide whether our designed pipelines are safe or not under applied load conditions. The durable and reliable work of compressor-pump stations used in the oil and gas industry has great importance for practice. Investigation of complex problems with respect to friction and wear (clearances), stresses, and thermodynamics phenomena in the piston machines, and oil and gas pipelines gives the opportunity to solve the problems of increasing the durability of these machines and pipelines. Confirmation that the new methodologies can be produced by the current supply chain improving manufacturing efficiency and reducing the environmental and social impact of the supply chain.

Effect of Ni content on microstructure and mechanical properties evolutions of 9Cr high Si heat resistant steel deposited metals

This work presents the effect of Ni content on the morphology of microstructure and changes of mechanical properties of high Si 9Cr heat resistant steel deposited metals with different states: as-welded, as-post weld heat treated (750 °C/2.5 h) and as-aged (550 °C/3000 h). With the increase of Ni content, the martensitic laths are refined improving the overall mechanical properties. δ ferrite deteriorates the impact toughness. During aging process, Ni facilitates the formation of M6X. Therefore the overall mechanical properties of deposited metal decreases as the Ni content increases after long-term aging owing to the formation of chain-like precipitates consisted mainly of M6X. The process of post weld heat treatment improves the negative effect of small-sized δ ferrite on impact toughness.