Changes In Grain Size Research Articles

Effect of Si on the Yield Strength of Medium-Carbon Steels Consisting of Ferrite and Pearlite

To enhance the intrinsic yield strength of the ferrite-pearlite microstructure that inevitably forms in a non-quenched-and-tempered steel for large structural components, this study analyzed the effect of adding Si. The resulting ferrite-pearlite microstructure in medium-carbon steels was examined, and the resulting increase in yield strength was interpreted based on strengthening mechanisms. Hot-rolled sheets of 0.3C-1.5Mn steels were fabricated with Si ranging from 0.22 to 2.21 wt. %. Austenitization was conducted at 880°C followed by slow continuous cooling, and ferrite-pearlite microstructures were formed. With increasing Si, the yield strength increased from 409.1 to 573.6 MPa. Although there was a negligible change in the austenitic grain size, the mean diameter of the ferritic grains decreased from 8.8 to 5.0 μm, while the mean interlamellar spacing of the pearlites decreased from 196.6 to 109.9 nm. Using these quantitative data about microstructural features and considering possible strengthening mechanisms, a model to predict yield strength was derived via a constrained optimization method. The resulting model indicated that the major mechanisms are the refinement of pearlitic interlamellar spacing and the solid solution strengthening of ferrite by Si. Their contribution to the increment in yield strength was over 75 %, while others such as ferritic grain refinement and increased pearlitic volume fraction have limited influence.

Evaluating the effect of A- and B-site cobalt doping on the structural, morphological, dielectric, and non-ohmic properties of CaCu3Ti4O12 ceramics prepared by the hydrothermal method

CaCu3Ti4O12 (CCTO), CaCu3-xCoxTi4O12 (CCCxTO) and CaCu3Ti4-xCoxO12 (CCTCxO) ceramics with x = 0.1 were synthesized by the hydrothermal process at 200°C for 24 hours. The influence of cobalt substitution on the copper and titanium sites in CaCu3Ti4O12 on the structural, morphological, and physical properties was investigated. It was shown through the analysis of X-ray diffractograms of CCTO, CCCxTO, and CCTCxO compounds that they crystallized in a pure perovskite structure without the presence of secondary phases. The refinement of the spectra using the Rietveld method showed an efficient formation of the crystalline phase of the cubic structure (Im3¯), which remains unchanged, with an increase in the unit cell due to the substitution of Co2+/Co3+ in the Cu2+ and Ti4+ sites of the CCTO ceramic. Raman spectroscopy was used as a complementary characterization method to XRD in order to detect vibrational bands and highlight any changes in the crystal lattice. SEM results showed that cobalt insertion increased the average grain size. The dielectric properties were studied by complex impedance spectroscopy in a frequency range from 1 kHz to 1 MHz at different temperatures, where the insertion of cobalt in the Cu2+ and Ti4+ sites has a significant effect on the permittivity value (εr) and dielectric losses (tanδ). The non-ohmic characteristics showed that the change in grain size due to cobalt incorporation is beneficial to improving the breakdown strength (Eb) and nonlinear coefficient (α), which can be attributed to the grain boundary properties of the Internal Barrier Layer Capacitor (IBLC) model and the behavior of the Schottky barrier.

Analysis of Influence of Ultrasonic Shot Peening on Surface Plastic Behavior of Superalloy

This work focuses on the effects of ultrasonic shot peening (USP) on grain refinement and orientation behavior in the surface region of GH4151 superalloy. The microstructure evolution of the alloy under USP durations were studied. The effects of USP-induced grain refinement, orientation, and dislocation motion behavior were analyzed. The results indicated that during the USP process, the plastic deformation of the surface layer of superalloys is accompanied by changes in grain size and orientation. The random impact of the spheres on the surface area promotes grain refinement and grain rotation, enhancing the randomness of grain orientations and reducing the texture strength and the proportion of “soft” orientation distribution. Over a long period of treatment, a large number of spheres cause the slip planes and slip directions of each grain to rotate due to the additional shear stress from the impact, resulting in relatively consistent plastic deformation on the surface and the enhanced randomness of grain orientations, thus reducing the high texture strength introduced by previous machining processes. The understanding of dislocation pile-up behavior and the relationship between externally applied shear stress, pile-up characteristics, and grain refinement is essential for optimizing the USP process and achieving the desired material properties.

Timing and evolution of structures within the southeastern Greater Caucasus and Kura Fold-Thrust Belt from multiproxy sediment provenance records

The Greater Caucasus (GC) mountains are the locus of post-Pliocene shortening within the northcentral Arabia-Eurasia collision. Although recent low-temperature thermochronology constrains the timing of orogen formation, the evolution of major structures remains enigmatic—particularly regarding the internal kinematics within this young orogen and the associated Kura Fold-Thrust Belt (KFTB), which flanks its southeastern margin. Here we use a multiproxy provenance analysis to investigate the tectonic history of both the southeastern GC and KFTB by presenting new data from a suite of sandstone samples from the KFTB, including sandstone petrography, whole-rock geochemistry, and detrital zircon (DZ) U-Pb geochronology. To define source terranes for these sediments, we integrate additional new whole-rock geochemical analyses with published DZ results and geological mapping. Our analysis reveals an apparent discrepancy in up-section changes in provenance from the different methods. Sandstone petrography and geochemistry both indicate a systematic up-section evolution from a volcanic and/or volcaniclastic source, presently exposed as a thin strip along the southeastern GC, to what appears similar to an interior GC source. Contrastingly, DZ geochronology suggests less up-section change. We interpret this apparent discrepancy to reflect the onset of sediment recycling within the KFTB, with the exhumation, weathering, and erosion of early thrust sheets in the KFTB resulting in the selective weathering of unstable mineral species that define the volcaniclastic source but left DZ signatures unmodified. Using the timing of sediment recycling and changes in grain size together as proxies for structural initiation of the central KFTB implies that the thrust belt initiated nearly synchronously along strike at ~2.0–2.2 Ma.

Study on the deterioration of mechanical properties of stainless steel S35657 exposed to overall stage of fire

Fires often have destructive effects on steel structures, putting the safety of building structures at serious risk. As a new austenite stainless steel, grade S35657, its in-fire and post-fire mechanical behavior has not been reported, which limits its application. In this paper, a total 68 stainless steel S35657 coupons were designed and tested, with 34 coupons used for in-fire tests and 34 for post-fire tests. The effects of heating temperatures, loading rates, and heating soaking times on the mechanical properties were investigated. The failure modes, as well as the stress-strain curves and mechanical properties, were acquired. Electron microscopy scanning analysis were also conducted on the coupons to study the fracture mechanisms at elevated temperatures. The test results showed a rapid decline in in-fire mechanical properties when the temperature exceeded 600 °C. The yield strength of the coupon at 1000 °C is only 9.1 % of that at room temperature. As the tensile rate increased, the strength of the coupon increased gradually. For post-fire coupons, there is no significant change in the mechanical properties of coupons at temperatures ranging from 20 °C to 900 °C. However, after reaching a temperature of 1000 °C, the coupon experienced a reduction in yield strength (up to 27.8 %) and an expansion in elongation (up to18.0 %), compared to the coupon at ambient temperature. This related to the change in grain size of the coupons after exposure to high temperatures. The heating soaking time has an insignificant effect on the post-fire mechanical properties of stainless steel S35657. Existing constitutive models in the literature cannot be well applied to stainless steel S35657, new constitutive models to predict the in-fire and post-fire mechanical properties have been established. Moreover, reduction factors for the key mechanical properties were compared with existing values, and new unified equations for stainless steel S35657 were proposed. Finally, a reliability analysis was performed to evaluate the proposed design rules, and it was deemed that the proposed design rules were reliable. The findings of this study will provide a reference for engineers in evaluating the in-fire and post-fire residual strength of stainless steel S35657, and offer guidance for fire resistance design and high-temperature repair reinforcement.

Effect of Synthesis Process on The Piezoelectric Properties of (1-x) NBT-xBT: A Comparative Study Between Solid State and Hydrothermal Methods

Lead-free oxide perovskite materials are produced to ensure that no toxic or dangerous waste is released into the environment, although this technique often requires a high-temperature synthesis method. Nevertheless, the development of an environmentally friendly chemical process to carry out the synthesis of perovskite material in the laboratory at low temperature is a major challenge. In this investigation, to lower the temperature of the thermal treatment, (1-x)(Na0.5Bi0.5)TiO3-xBaTiO3 (abbreviated as (1-x)NBT-xBT) ceramics were synthesized using two different methods: a hydrothermal method and a conventional calcination process (solid-state), using the same reagents. The effects of various synthesis techniques on the composition, structure, morphology, and dielectric properties of the (1-x)NBT-xBT ceramics were registered and examined. The XRD plots taken at ambient temperature were used to verify the phase formation of the samples. The occurrence of functional bands was also verified by Raman spectroscopy at ambient temperature. Using the Rietveld refinement method were able to detect the morphotropic phase boundary (MPB) near x=0.05-0.07. When the hydrothermal process was adopted, the (1-x)NBT-xBT ceramics show a single perovskite structure sintered at 1000°C. Moreover, scanning Electron Microscopy (SEM) examination revealed a uniform distribution of grains and a significant change in grain size with the increase in BaTiO3 concentration when compared to the conventional method. The microstructure of ceramics is generally strongly influenced by the method used to prepare the powders, which has a considerable impact on their performance. Piezoelectric and dielectric properties of the specimens have been compared with the properties of those prepared by the hydrothermal process. Thus, the choice of the suitable synthesis method depends on the desired properties of the (1-x)NBT-xBT materials.

Influence of multiple friction stir welding passes on the microstructure and mechanical properties of AA2024 age-hardened aluminum alloy

Friction stir welding (FSW) is a promising joining process for age-hardened aluminum alloys. However, when the process is used for welding age-hardened aluminum alloys, the hardness and joint efficiency are poor mainly because the strengthening precipitates become incoherent and/or get dissolved during the welding process. In this novel work, efforts have been made to enable the reprecipitation of the strengthening precipitates using multi-pass FSW. After producing FSW welds on AA2024 alloy, the welds have been processed by the same tool and at the same parameters several times to facilitate the reprecipitation of strengthening precipitates. As the precipitation kinetics of age-hardened aluminum alloys are temperature-dependent, a thermal imaging camera was utilized to record the temperature history during welding and subsequent cooling of the welded plates. The metallurgical examination of welded samples was carried out using optical microscopy, Scanning Electron Microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and microhardness test. It was observed that grain refinement occurs continuously due to dynamic recrystallization and severe plastic deformation up to the third FSW pass, after which there is no significant change in grain size. Generally, the microhardness value was higher in the stir zone than the heat-affected zone (HAZ), and the hardness in the stir zone increased after 4 passes of FSW. SEM images show clusters of incoherent precipitates, fragmentation, precipitate dispersion, dissolution, and reprecipitation of precipitates during each subsequent pass. The identification of the precipitates was carried out using EDS and XRD analysis.

The role of a tantalum interlayer in enhancing the properties of Fe3O4 thin films.

High spin polarization and low resistivity of Fe3O4 at room temperature have been an appealing topic in spintronics with various promising applications. High-quality Fe3O4 thin films are a must to achieve the goals. In this report, Fe3O4 films on different substrates (SiO2/Si(100), MgO(100), and MgO/Ta/SiO2/Si(100)) were fabricated at room temperature with radio-frequency (RF) sputtering and annealed at 450 °C for 2 h. The morphological, structural, and magnetic properties of the deposited samples were characterized with atomic force microscopy, X-ray diffractometry, and vibrating sample magnetometry. The polycrystalline Fe3O4 film grown on MgO/Ta/SiO2/Si(100) presented very interesting morphology and structure characteristics. More importantly, changes in grain size and structure due to the effect of the MgO/Ta buffering layers have a strong impact on saturation magnetization and coercivity of Fe3O4 thin films compared to cases of no or just a single buffering layer.

Early diagenesis, sedimentary dynamics and metal enrichment reveal deep-sea ventilation in Magellan Seamounts during the middle Pleistocene

Seamounts are ubiquitous topographic units in the global oceans, and the Caiwei Guyot in the Magellan Seamounts of the western Pacific is a prime example. In this study, we analyzed a well-dated sediment core using magnetic properties, sediment grain size, and metal enrichment to uncover regional ventilation history during the middle Pleistocene and explore potential linkages to global climate changes. Our principal findings are as follows: (1) The median grain size is 3.3 ± 0.2 μm, and clay and silt particles exhibit minimal variation, with average values of 52.8 ± 1.8% and 38.2 ± 1.6%, respectively, indicating a low-dynamic process; (2) Three grain-size components are identified, characterized by modal patterns of ~3 μm (major one), ~40 μm, and 400–500 μm, respectively; (3) Magnetic coercivity of the deep-sea sediments can be classified into three subgroups, and their coercivity values are 6.1 ± 0.5 mT, 25.7 ± 1.0 mT, and 65.2 ± 2.1 mT. Based on these results, we propose a close linkage between magnetic coercivity and metal enrichment, correlating with changes in deep-sea circulation intensity. Conversely, sediment grain-size changes seem to be more strongly influenced by eolian inputs. Consequently, we suggest that regional ventilation has weakened since ~430 ka, likely linked to a reduction in Antarctic bottom water formation.

Effects of Anthropic Structures on Morphodynamic Beach Evolution along the Gulf of Roses (Northwestern Mediterranean, Spain)

This study conducts a morphodynamic analysis of beaches located in the northern sector of the Gulf of Roses (NW Mediterranean, Spain). The primary objective is to investigate mid-short (2004–2020) term spatial and temporal variations in shoreline position and sedimentological behaviour. The study area covers the northern part of the gulf, spanning 9.86 km, and includes both natural beaches and heavily anthropized ones. The following GIS methodologies were employed to study the variations in the coastline: QGIS for areas and DSAS-ArcGIS for transects, quantifying coastal changes from 2004 to 2020. Sediment samples were collected from both the dry beach and swash areas for each profile. The results reveal minor discrepancies in shoreline evolution data, depending on the method used (transects or areas). Profile-based analysis shows an average annual rate of −0.11 m·y−1 (ranging between 0.53 and −0.55 m·y−1), while areal-based results (2004–2020) indicate a total loss of −20,810 m2 (−1300 m2·y−1). Sediment grain size decreases northward (from 745 to 264 µm in the swash zone). Changes in shoreline position and grain size illustrate the impact of various anthropogenic structures on morphodynamic behaviour. These structures preferentially deposit specific grain sizes and impede sediment transport, which will cause an advance in the position of the shoreline and sediment grain sizes upstream and a reverse process downstream. This study underscores the influence of coastal anthropization on beach morphology and sedimentology, generating distinct morphodynamic behaviour.

Comparative study of microstructural evolution and mechanical properties in friction stir processed, reinforced friction stir processed, and heat-treated reinforced friction stir processed Al composites

The development of friction stir welding (FSW) created the basic foundation for friction stir processing (FSP). This process entails refining the local microstructure and achieving the localised plastic deformation due to the stirring effect of the tool, which may involve adding additional filler material as required. The rotating tool involved in the process has a shoulder and pin responsible for heat generation for plastic deformation and localised mixing. The rotating tool is inserted and traversed on the desired surface, tailoring the material properties. The tool’s exposure to the surface causes localised plastic deformation and thermal gradient, and microstructural changes occur locally. The present investigation uses Friction Stir Processing (FSP) to fabricate an aluminium metal matrix composite. Recently, the use of aluminium alloy has been replaced by composites because of their increased mechanical and physical properties (specific properties). The experiment leads to manufacturing an aluminium metal matrix composite using aluminium oxide, boron carbide and commercially pure copper dust. Later, the effect of heat treatment on the respective metal matrix composite is studied. A comparative study among three different types of FSP techniques viz. FSP, Reinforced FSP, and Heat-treated Reinforced FSP have been performed. The tool revolution speed (RPM) and tool traverse speed of 400 RPM and 10 mm/min had been implemented, respectively. The T4 Heat-Treatment cycle was used during the current investigation. This investigative study was performed to analyse the changes in grain sizes and hardness values at the stir zone (SZ), thermo-mechanically affected zone (TMAZ), heat affected zone (HAZ) and on the base materials (BM) of the samples. The reinforced FSP metal matrix composite (MMC) showed an 81.26% increase in the micro-hardness value (HV) compared to the base metal. Further on analysing the microstructures, the reinforced FSP composite showed a 65.20% reduction in grain size. Moreover, the Heat-Treated sample showed an increase in the micro-hardness value by 99.8%.

Decoupling the roles of grain boundary strength and grain size hidden in grain-level electro-chemo-mechanical failure of solid-state electrolyte

Garnet lithium lanthanum zirconium oxide (Li7La3Zr2O12, LLZO) is a benchmark solid-state electrolyte material receiving considerable attention owing to its high conductivity and chemical stability against Li metal. Although its electro-chemo-mechanical failure mechanisms have been much investigated, the equivocal roles of grain boundary strength and grain size of LLZO remain under-explored, hindering further performance improvements. Here we decoupled the effects of grain size and grain boundary strength of polycrystalline LLZO via the combination of electrochemical kinetics and the cohesive zone model. We discovered that the disintegration of LLZO is initiated by the accumulation of local displacements, which strongly relates to the changes in both grain size and grain boundary strength. However, variations in grain boundary strength affect the diffusion and propagation pathways of damage, while the failure of LLZO is determined by the grain size. Large LLZO grains facilitate transgranular damage under low grain boundary strength, which can alter local chemo-mechanics within the bulk of LLZO, leading to more extensive damage propagation. The results showcase the structure optimization pathways by preferentially controlling the growth of lithium dendrites at grain boundaries and their penetration in garnet-type SSE.

A new aspect of the effect of fluorine doping on structural and superconducting properties in the Bi2Sr1.6La0.4CuO5+δ(O1-xFx) ceramic system

In this study, ceramic samples with the nominal composition Bi2Sr1.6La0.4CuO5+δ(O1-xFx) (where x = 0, 0.2 and 0.4) were synthesized using the solid-state reaction method to investigate the effects of fluorine anionic doping on the Bi-2201 system's structural, microstructural, and superconducting properties. X-ray diffraction analysis (XRD) confirmed the Bi-2201 phase in all samples and total incorporation of fluorine. Doping with fluorine reduced orthorhombicity, leading to an orthorhombic-tetragonal transition. Scanning electron microscopy (EDS) revealed changes in grain shape and size, while energy dispersive x-ray analysis (EDAX) confirmed fluorine incorporation. DC-electrical resistivity measurements showed that fluorine doping decreased the critical transition temperature TC (Onset), with a greater decrease observed at higher fluorine concentrations. The resistivity increase in the normal state of the sample with x = 0.4 was also noted. The conduction mechanism above TC (Onset) = 26.10 K followed the Arrhenius law, indicating thermally activated behavior due to a band gap.

Отримання жароміцного гомогенного сплаву методом пресування та спікання суміші порошків (Nb-21Ti-5Al-10Cr-7Mo) ат. %

Multicomponent high temperature strength alloys of the Nb-Ti-Al system, alloyed with Cr, Zr, Mo and Si, with a specific gravity of 6.3 - 7.4 g/cm3, have proven extremely promising in aviation and space technology. However, their physical and chemical features are associated with the high activity of the components, with a significant difference in melting temperatures (from Tmel. Mo – 2617 °C to Tmel. Al – 660 °C) and different specific gravity (from 10.2 g/cm3- Mo up to 2.7 g/cm3- Al), is a big problem for their production. The long crystallization interval of cast alloys of this system, thermophysical features of their crystallization, determine the possibility of formation of dendritic structures, the development of dendritic liquation and segregation of low- or high-temperature intermetallics and eutectics, the tendency to the formation of crystallization cracks, which reduces the operational characteristics of cast alloys. In this regard, it became necessary to investigate the possibilities of obtaining an alloy by the method of powder metallurgy. The purpose of this work was to obtain a homogeneous alloy, to study changes in the grain structure, phase transformations and mechanical properties of the material at various stages of processing in the process of obtaining a homogeneous alloy structure by powder metallurgy methods. The need to protect powder components from oxidation, formation of nitrides, carbides during technological operations at temperatures above 200 °C (high-purity argon) has been established. The optimal duration of intensive grinding of a mixture of powders and granules of raw materials has been worked out, which makes it possible to control the uniformity of the size of the particles of the mixture components, porosity and homogeneity of the alloy. The optimal duration of grinding is 30 minutes, during which the most homogeneous mixture in terms of particle size is formed. The optimal annealing mode was established, which ensures the achievement of homogenization of the alloy, phase transformations at the boundaries of the contact of component particles, and changes in grain sizes. Microstructural and X-ray structural analysis of the samples was carried out, their microhardness and grain dispersion were determined. Keyword: high-temperature strength niobium alloys, physical and chemical features, powder metallurgy, homogeneity, microstructure, mechanical properties, phase composition.

Study on dynamic recrystallization and precipitation behavior of hot compressed Al-20Zn-0.5Mg-0.5Sc alloy

The dynamic recrystallization (DRX) behavior of the Al-20Zn-0.5Mg-0.5Sc alloy was investigated under specific conditions using a Gleeble-3500 thermal simulator. The resultant grain size, recrystallization degree and precipitated phases were studied. The results indicate that the sensitivity of DRX grain size is highly affected by temperature, feebly influenced by strain and intermediately affected by strain rate. The DRX grains are grown by an average of 3.49 μm with increasing temperature. The DRX behavior is sensitive to temperature, strain and strain rate, resulting in changes in average grain size, percentage of HAGBs and degree of recrystallization under different parameters. At 400 ℃ / 40 % / 0.1 s−1, the average grain size is refined to 12.90 μm, and the corresponding HAGBs and recrystallization degree are approximately 46.2 % and 34.3 %, respectively. The Al3Sc, Zn and η (MgZn2) phases are precipitated in the hot-compressed alloy. The Al3Sc phase promotes the precipitation of the Zn and η phases. The size, amount and morphology of Al3Sc, Zn and η phases at different parameters have an important influence on the movement of dislocations and nucleation of grains, which leads to changes in DRX grain size and the degree of recrystallization. The fine precipitated phase particles Al3Sc and η inhibit the growth of recrystallized grain by pinning grain boundaries and exerting a blocking force on dislocations. Dynamic precipitation is the dominant mechanism for the changes in DRX grain size and degree of recrystallization. To achieve the refined grains and homogeneous microstructures, the optimum parameters are recommended as 400 ℃, 0.1 s−1 and 50 %.

Microstructural evolution of GH4079 superalloy during hot deformation and heat treatment

Through hot compression and subsequent heat treatment experiments on GH4079 superalloy, the influence of different hot deformation and heat treatment conditions on the evolution of GH4079 superalloy microstructure was studied. The evolution of grains and γ′ phases under different thermomechanical conditions was investigated. The results indicate that at deformation temperatures above 1100 °C and strain rates ranging from 0.01 to 0.1 s−1, the primary mechanism of dynamic softening in the alloy is discontinuous dynamic recrystallization (DDRX). When the deformation temperature is below 1100 °C and strain rates range from 0.01 to 0.1 s−1, both continuous dynamic recrystallization (CDRX) and DDRX are the main dynamic softening mechanisms. Due to high strain energy accumulation, the samples deformed at lower temperatures (below 1100 °C) and then solution-treated at 1120 °C for 8 h exhibit significant increases in recrystallization volume fraction and recrystallization grain size. Conversely, the samples deformed at higher temperatures (above 1100 °C) and then solution-treated at 1120 °C for 8 h show minimal changes in recrystallization volume fraction and recrystallization grain size. After solution treatment at 1140 °C, the grain size of the alloy significantly increases. The samples deformed at higher strain rates exhibit the evolution of fine γ′ phases into elongated rod shapes during solution treatment, while larger γ′ phases undergo splitting processes.

Research on a new type of ureteral stent material Zn-2Cu-0.5Fe-xMn with controllable degradation rate

The placement of ureteral stents plays a crucial role in the treatment of ureteral strictures, therefore requiring high material performance standards. In addition, depending on the etiology of ureteral strictures, there are significant differences in the retention time of ureteral stents, thus requiring different degradation rates for the stents. Therefore, it is crucial to develop stent materials with high performance and controllable degradation rates. This study explores the potential of Zn-2Cu-0.5Fe-xMn alloy as a ureteral stent material, utilizing the antibacterial effect of copper ions, the strengthening effect of Fe element on Zn-based alloys, and the accelerated degradation effect of Mn element. The research found that with the increase in Mn content, the average grain size of the alloy and the size of (Fe, Mn)Zn13 phase gradually increased, leading to a decrease in hardness. The corrosion rate of the alloy increased with the increase in Mn content, attributed to changes in grain size and standard electrode potential differences between elements. Due to the antibacterial effects of Zn ions and Cu ions, the Zn-2Cu-0.5Fe-xMn alloy exhibits good anti-stone formation capabilities. Furthermore, the alloy also demonstrates acceptable cytotoxicity. Therefore, the Zn-2Cu-0.5Fe-xMn alloy is expected to become an important implant material in urological surgery.

Improved ferroelectricity and endurance in Ca doped Hf0.5Zr0.5O2 films

Doped Hf0.5Zr0.5O2 materials have drawn increasing attention due to the excellent ferroelectric properties, but the relevant research is just in the preliminary stage and the reported doped systems are rare. In this work, Ca doped Hf0.5Zr0.5O2 (Ca:HZO) ferroelectric films were successfully fabricated via chemical solution deposition and investigated for the first time. It is observed that Ca doping induces a phase transformation from monoclinic to orthorhombic/tetragonal and then to monoclinic/tetragonal. The highest orthorhombic phase fraction is achieved in 2.5 mol% Ca doped HZO film, contributing to the optimum ferroelectric property with the largest remnant polarization of 14.00 μC/cm2 after 105 cycles. Additionally, the leakage current density is observed to decrease with increasing Ca content, which is mainly associated with the changes of grain size and surface roughness. As a result, the endurance is significantly improved in the Ca doped films, and an excellent endurance of 1010 cycles is achieved in the 2.5 mol% Ca doped film. These results suggest that Ca doping can enhance the ferroelectric and endurance properties of HZO films by optimizing the phase and morphological structure.

Observation of dielectric anomaly at magnetic transition temperature in NdMn1xZnxO3/SNTO (x = 0.00, 0.05, 0.10) films

We report our observation of dielectric anomaly from temperature–dependent dielectric study near the antiferromagnetic transition (TN) in pure and Zn–doped NdMnO3/SNTO (SrNb0.002Ti0.998O3) epitaxial films. Structural and microstructural studies showed the presence of compressive strain along the a–axis and changes in grain size due to Zn–substitution. The variation in the elemental concentration of Zn was confirmed by RBS measurements led to amend Mn–Mn exchange interactions in doped films. Alteration in TN due to Zn–doping, obtained from D.C. magnetization is consistent with the dielectric anomaly temperatures, indicating the presence of magnetoelectric effect in pure and Zn–doped NdMnO3/SNTO system.

Repairability and effectiveness in direct energy deposition of 316L stainless steel grooves: A comparative study on varying laser strategy

Direct energy deposition (DED) has gained attention in the field of metal repair because of its ability to integrate additively deposited material with preexisting components. Having the beneficial aspects of depositing right material, DED is evaluated the best option for repair deposition. Machining grooves in damaged components is the common first to repair, which is necessary to remove cracked or damaged material and provide suitable geometry for deposition. Preprocessing as grooving is commonly applied to prevent the propagation cracks or tears. However, challenges such as dimensional error and crack induced by residual stress emerge owning to complex interactions between the DED parameters and groove geometry during repair deposition. This study investigates effective deposition strategies for repairing 316L stainless steel grooves with wall-angles of 90° and 135° by exploring the relationship between the repair integrity and parameters such as groove angles, laser energy input, and powder supply, all with reference to the underlying mechanism of metallurgical bonding in angled areas. Based thereon, a modified effective repair strategy is proposed, using enhanced dual laser power to address bonding issues in the angled areas. Samples repaired using this method exhibit a defect-free groove–deposit interface and a continuous columnar-grained microstructure with abrupt changes in grain size between the repaired area and groove. This microstructural heterogeneity results in an exceptional combination of strength and ductility when compared to the base material and samples repaired using a single laser strategy. The findings of this study provide insights into the optimization of DED strategies for achieving robust metallurgical bonding within grooves, thereby advancing technological maturity in the field of metal repair.