Changes In Electrical Conductivity Research Articles

Temperature and state-dependent electrical conductivity of soft biological tissue at hyperthermic temperatures

Objective: We present a physics-based, temperature and state-dependent electrical conductivity model for soft biological tissue under thermal therapies with a quantified damage parameter that represents the state of soft biological tissue (degree of denaturation). Most existing models consider electrical conductivity to be only temperature-dependent and evaluate tissue damage during post-processing after temperature calculation. Our model allows tissue damage to be coupled into the thermal model for a more accurate description of both RF ablation and electrosurgery. Methods: We model the denaturation process with an Arrhenius-type differential equation for chemical kinetics and a modified Stogryn equation for electrical conductivity under state transition. We present experimental data from two types of heating procedures at 128 kHz to validate and showcase the capability of our model. Results: Our model is able to capture the change in electrical conductivity during heating, cooling, and reheating procedures, which distinguishes different states and shows the irreversibility of denaturation. The model also accurately captures tissue change during slow cooking at a constant temperature, highlighting a state dependence. Conclusion: By incorporating state dependence into the model for electrical properties, we are able to capture the denaturation process more accurately and distinguish different degrees of damage. Our model allows the modeling of procedures involving repeated heating or cooling, which is impossible for models without a state dependence. While being able to adapt to patient-specific needs, the model can be used to improve planning and control in future robot-assisted surgeries to reduce unnecessary damage.

Evaluate the potential adsorption of graphynes (perfect and doped) for nitrogen mustard gas: A first principles study

Density functional theory (DFT) calculations are used to thoroughly examine the reactivity and electronic sensitivity of pristine and BN-doped graphyne (BNG) toward nitrogen mustard (NM). Graphyne’s electrical conductivity is unaffected by the weak adsorption of NM, which occurs via the Cl atom on the material with an adsorption energy of roughly −3.1 kcal.mol−1. In addition to decreasing graphyne’s reactivity and work function, substituting isoelectronic BN linkages for CC linkages enhances the HOMO-LUMO energy gap (Eg). BNG’s electrical conductivity increases when Eg drops from 2.99 to 1.82 eV due to the adsorption of NM. Additionally, a significant change in BNG’s work function results in a variation in the field electron emission current. Lastly, it is anticipated that the desorption of NM from the BNG surface will take a brief recovery time of roughly 0.05 s at room temperature. It has also been demonstrated that NM concentration affects changes in electrical conductivity. The findings also suggest that BNG could be a promising NM sensor.

The Effect of Eco-Friendly Deicing Agents Containing Humic Acid on Plant Growth

Objectives:In this experiment, we used an environmentally friendly snow removal agent containing calcium chloride (CaCl2) and humic acid (HA) to alleviate salt stress on chili pepper seedlings, and analyzed its effect on plant growth. As an alternative to minimize the negative effects of existing chloride-based snow removal agents on plants and soil, we investigated whether humic acids contribute to improving plant physiological responses and soil electrical conductivity (EC). Evaluated.Methods:For 21 days, we set up a control group (Count.), a calcium chloride treatment group (CaCl2), a humic acid treatment group (HA), and a mixed treatment group (HUA2, HUA5, HUA10) in which humic acid and calcium chloride were mixed. The growth of stems and roots was measured. In addition, the high mortality rate of leaves and changes in soil electrical conductivity (EC) were measured to evaluate the effect of alleviating salt stress.Results and Discussion:As a result of the experiment, stem length increased in the control group, humic acid treatment group (HA), and humic acid and calcium chloride mixed treatment groups (HUA2, HUA5, HUA10), and the greatest growth was observed in HUA5 among the mixed treatment groups. On the other hand, in the calcium chloride treatment group (CaCl2), stem growth did not occur and the high leaf mortality rate was 66.7%, which had a negative effect on growth. The soil EC value was lowest at 0.21mS/cm in the humic acid only treatment group (HA) and highest at 1.25mS/cm in the calcium chloride treatment group (CaCl2). In the mixed treatment group, the EC value tended to decrease as the humic acid concentration increased. This indicates that humic acid can play a role in reducing salt stress and promoting plant growth.

Structural characterization and dosimetric response evaluation of (SnO<sub>2</sub>)<sub>0.3</sub>(TiO<sub>2</sub>)<sub>0.7</sub> thin film

This study investigates the effect of X-ray radiation on the I-V characteristics of (SnO2)0.3(TiO2)0.7 thin film in a voltage range of 0- 8 The thin film was developed using the aerosol assisted chemical deposition technique. The amorphous character of the films was shown by the XRD spectra, which showed peaks corresponding to SnO2 and TiO2. Smooth surface morphology with tiny poses was indicated by the FESEM picture, and 2.73 μm film thickness was identified in the cross-sectional investigation. The I-V characteristics result indicates that the electrical conductivity changes throughout a range of applied voltages, from 0 to 8 V. The I-V characteristic measurements obtained during irradiation with X-ray dosage (dose rate) ranging from 100 cGy (250 cGy/min) to 200 cGy (350 cGy/min) and a voltage range of 1.0V to 8.0 V indicate that the current increases linearly with X-ray doses and dose rate. The thin film’s ability to undergo structural changes due to X-ray radiation makes it a valuable dosimetric sensor.

Point-of-care breath sample analysis by semiconductor-based E-Nose technology discriminates non-infected subjects from SARS-CoV-2 pneumonia patients: a multi-analyst experiment.

Metal oxide sensor-based electronic nose (E-Nose) technology provides an easy to use method for breath analysis by detection of volatile organic compound (VOC)-induced changes of electrical conductivity. Resulting signal patterns are then analyzed by machine learning (ML) algorithms. This study aimed to establish breath analysis by E-Nose technology as a diagnostic tool for severe acute respiratory syndrome coronavirus type 2 (SARS-CoV-2) pneumonia within a multi-analyst experiment. Breath samples of 126 subjects with (n=63) or withoutSARS-CoV-2 pneumonia (n=63) were collected using the ReCIVA® Breath Sampler, enriched and stored on Tenax sorption tubes, and analyzed using an E-Nose unit with 10 sensors. ML approaches were applied by three independent data analyst teams and included a wide range of classifiers, hyperparameters, training modes, and subsets of training data. Within the multi-analyst experiment, all teams successfully classified individuals as infected or uninfected with an averaged area under the curve (AUC) larger than 90% and misclassification error lower than 19%, and identified the same sensor as most relevant to classification success. This new method using VOC enrichment and E-Nose analysis combined with ML can yield results similar to polymerase chain reaction (PCR) detection and superior to point-of-care (POC) antigen testing. Reducing the sensor set to the most relevant sensor may prove interesting for developing targeted POC testing.

Assessing changes in soil electrical conductivity under runoff influences using gradient boosting and metaheuristic algorithms

Assessing changes in soil electrical conductivity under runoff influences using gradient boosting and metaheuristic algorithms

Release of selected nutrients from polymer-coated fertilisers in the soil environment

The aim of the study was to evaluate the release of NH4-N and PO4-P from polymer-coated fertilisers in the soil environment, and to analyse their impact on pH and conductivity of the soil leachates. In this investigation mineral NPK(S) 6-20-30(7) fertiliser (as a starting material), commercial, controlled-release OsmocoteTM fertiliser (as a reference material) and four polymer-coated fertilisers have been used. Biodegradable polybutylene(succinate-co- dilinoleate), polyethylene(succinate-co-terepftalate) and chitosan have been used as coating materials. The experiments were conducted in the laboratory conditions, in PVC columns filled with air-dry soil. The nutrients release from the investigated materials was explained based on the diffusion mechanism and it was interpreted with the use of the Korsmeyer–Peppas kinetic model. Two mechanisms dominate in the release process of nutrients: the mechanism based on quasi-Fickian diffusion and non-Fickian (anomalous case) mechanism. The largest changes of pH and electrical conductivity (EC) of soil leachates occurred in the initial period of research for all tested fertilisers (pH: 9.5–20.3% – loamy sand (S1) 7.9–20.6% – sandy loam (S2); EC: 438–1667% – S1, 771–1509% – S2). The polymer coating significantly reduces the nutrient release from the fertiliser core. The size of these changes depends on the type and thickness of the polymer layer and the physicochemical properties of the soils.

Study of mechanical and electrical properties through positron annihilation spectroscopy for ethylene-propylene-diene rubber biocomposites with treated wheat husk fibers

The positron annihilation lifetime (PAL) spectroscopy characteristics of ethylene-propylene-diene monomer rubber (EPDM) composites reinforced with treated wheat husk fibers (WHFs) were investigated for the first time. PAL spectroscopy is employed to study the free volume of polymers. The use of lignocellulosic materials as reinforcement in polymeric composites has gained attention due to their low cost, availability, and eco-friendliness. In this study, the impact of the loading concentration on the interfacial adhesion between the EPDM matrix and WHFs is quantified, along with the evaluation of swelling measurement and tensile properties. Additionally, the nanoscopic properties derived from PAL spectroscopy correlate with the composites’ macroscopic properties. In addition, the dielectric properties of the investigated samples have been studied, and their conductivity has been calculated. To determine the conduction mechanism within these samples and how it is affected by the addition of WHF, the change in electrical conductivity with the frequency of the external electric field applied to the samples was studied, and from this, the conduction mechanism was determined, and the barrier height value was calculated. The experimental results provide insights into the relationship between the structure and properties of EPDM-WHF biocomposites, offering valuable knowledge for developing sustainable and high-performance materials.

Effects of Long-Term Reed Plantation on Saline Habitat

In recent years, the improvement and utilization of saline-alkaline soil has gradually shifted from engineering measures to biological measures. As a salt-tolerant plant, the reed has been preliminarily proven to have a role in improving saline-alkaline land. In order to explore the long-term effect of planting unharvested reeds on the improvement of saline-alkaline land, a pilot plot was set up in Fuping Pilot Test Base (34° 42'180"E; 109°11'49" N) near Lubo Beach, Fuping, Shaanxi, in 2012 to ascertain the improvement effect of long-term reed cultivation on saline–alkaline land. The objective was to study the long-term changes in soil pH, electrical conductivity, Ca2+, Mg2+, Cl-, SO42-, HCO3-, and CO32- contents, soil particle size and soil fertility. Results showed that (i) reed cultivation could effectively reduce soil salinization in the long term. From 2012 to 2022, the average pH of saline soil decreased from 9.42 to 8.86, and the electrical conductivity decreased from 1.20 μS/cm to 0.70 μS/cm. (ii) Reed cultivation considerably reduced the contents of Ca2+, Mg2+, Cl-, SO42-, HCO3-, and CO32- in the soil in the long term, and the reduction in each index was 5.9, 41.7, 63.5, 90.6, 81.7, 90.6, 77.9and 90.3%, respectively. (iii) Reed cultivation changed the soil structure. The soil texture of the 0–60 cm soil layer changed from silty sandy loam to silty loam from 2018 to 2022. (iv) Long-term reed planting without harvesting effectively improved soil fertility. In 2012, the content of soil organic matter was only 2.74 g/kg, but in 2022, the value reached 12.8 g/kg. Reed planting improved the physical and chemical properties of saline soil. Therefore, biological restoration of reed can be considered in low-lying saline–alkaline areas with high water volumes. Bangladesh J. Bot. 53(3): 665-672, 2024 (September) Special

Design of non-heat-treatable Al-Fe-Ni alloys with high electrical conductivity and high strength via CALPHAD approach

Electrical conductivity and strength are two critical properties concerned for rotors materials in electric vehicles. However, the two properties are often mutually exclusive in cast Al alloys. The present work proposes a novel non-heat-treatable Al-Fe-Ni alloy by considering the intermetallic compound’s content and morphology. With the modification of Ni and Fe content, the solidification path of designed alloy were calculated to predict the phase composition, which would greatly impact their performance. The as-cast Al-2Fe-1Ni (wt%) alloy exhibits comprehensive properties with an ultimate tensile strength of 131.2±2.5 MPa, an elongation of 20.2±3.6 % and an electrical conductivity up to 52.0±0.1 %IACS. The eutectic microstructure of Al13(Fe,Ni)4+α-Al in Al-2Fe-1Ni alloy accounts for over 90 %, much larger than the eutectic content in Al-0.4Fe-3.4Ni and Al-1Fe-1Ni alloys. The fine eutectics in Al-2Fe-1Ni alloy improve the second-phase strengthening effects and plastic deformation capability. In addition, the fibrous rod-like intermetallic reduces the electron scattering during the propagation process and leaves more space for free electron movement. The dominant second phase transforms from Al3Ni phase to Al9FeNi phase, further enhancing the thermal stability of the alloy. After aging treatment at 180 °C for 100 h, it shows no noticeable change in electrical conductivity and mechanical properties. It is hoped that this work can provide a new design approach for high-strength and high-conductivity Al alloys.

Changes in Microstructure, Mechanical Properties, and Electrical Conductivity of Severely Drawn AA1070 Wire with Annealing

The drawing process severely deforms commercial AA1070 alloy for electrical wire, reducing a rod from a diameter of 2.0 mm to 0.4 mm, followed by annealing. The annealing process was conducted at various temperatures ranging from 200℃ to 450℃, with each temperature maintained for 1hour. The effects of increasing annealing temperature on the microstructure, mechanical properties, and electrical properties of the Al wire were investigated in detail. The drawn Al wire showed a severely deformed microstructure and fiber texture that {110}<111> and {112}<111> components strongly developed. As the annealing temperature increased, the deformation structure changed into recrystallization structure over all regions. However, the fiber texture still strongly remained even in the specimens annealed at higher temperatures. The hardness decreased with increasing annealing temperature due to the occurrence of recovery and/or recrystallization. The strength also continued to decrease as the annealing temperature increased. However, elongation gradually increased with increase of annealing temperature to 250℃; above 275℃, it increased particularly sharply. The electric conductivity tended to increase slightly with increasing annealing temperature, reaching a maximum value of 62.2%IACS at 300℃. Changes in microstructure, mechanical properties and electrical conductivity with annealing of commercially drawn AA1070 were compared with those of the previous study.

Acoustoelectric Effect due to an In-Depth Inhomogeneous Conductivity Change in ZnO/Fused Silica Substrates

The acoustoelectric (AE) effect induced by the absorption of ultraviolet (UV) light at 365 nm in piezoelectric ZnO films was theoretically and experimentally studied. c-ZnO films 4.0 µm thick were grown by the RF reactive magnetron sputtering technique onto fused silica substrates at 200 °C. A surface acoustic wave (SAW) delay line was fabricated with two split-finger Al interdigital transducers (IDTs) photolithographically implemented onto the ZnO-free surface to excite and reveal the propagation of the fundamental Rayleigh wave and its third harmonic at about 39 and 104 MHz. A small area of a few square millimeters on the surface of the ZnO layer, in between the two IDTs, was illuminated by UV light at different light power values (from about 10 mW up to 1.2 W) through the back surface of the SiO2 substrate, which is optically transparent. The UV absorption caused a change of the ZnO electrical conductivity, which in turn affected the velocity and insertion loss (IL) of the two waves. It was experimentally observed that the phase velocity of the fundamental and third harmonic waves decreased with an increase in the UV power, while the IL vs. UV power behavior differed at large UV power values: the Rayleigh wave underwent a single peak in attenuation, while its third harmonic underwent a further peak. A two-dimensional finite element study was performed to simulate the waves IL and phase velocity vs. the ZnO electrical conductivity, under the assumption that the ZnO layer conductivity undergoes an in-depth inhomogeneous change according to an exponential decay law, with a penetration depth of 325 nm. The theoretical results predicted single- and double-peak IL behavior for the fundamental and harmonic wave due to volume conductivity changes, as opposed to the AE effect induced by surface conductivity changes for which a single-peak IL behavior is expected. The phenomena predicted by the theoretical models were confirmed by the experimental results.

Thermoelectric and electrical transport properties of mixed-conducting multicomponent oxides based on Ba(Zr,Ce)O3-δ

In this work, the chosen physicochemical properties of single-phase multicomponent oxides BaTi1/8Fe1/8Co1/8Y1/8Zr1/8Sn1/8Ce1/8Hf1/8O3-δ and BaTi1/9Fe1/9Co1/9Y1/9Zr1/9Sn1/9Ce1/9Hf1/9Bi1/9O3-δ were studied. The microstructure of the compounds strongly depended on the presence of bismuth in the structure. The electrical transport studies showed a level of electrical conductivity of ∼10-3 - 10-2 S/cm in the temperature range 673 – 1073 K. Electrical conductivity was thermally activated and the dominant conduction mechanism was the hopping of small polarons. Moreover, total electrical conductivity changes in the dry and humidified atmosphere at lower temperatures due to the presence of protonic defects in the structure. Thermoelectric measurements showed a relatively high value of the Seebeck coefficient for studied ceramics. Its values ranged between 50 and 250 μV/K depending on the sample and temperature. The Seebeck coefficient sign was positive, meaning that electron holes and/or oxygen vacancies were predominant charge carriers in oxidising atmospheres. Additionally, the Seebeck coefficient was found to be different in the humidified atmosphere which indicates an influence of protonic defects on thermoelectric transport. The obtained power factor Pf turned out to be low and dependent on the presence of protonic defects in the structure. This indicates, that the efficiency of the MOs-based operating thermoelectric generators can be controlled by changing the partial pressure of water vapor.

Determination of the elemental composition and changes in thermal and electrical conductivity of “Hanford” and low-ash medium-grained graphite’s grade graphites depending on the fast neutrons fluence

Studying the properties of graphite recovered from operating nuclear reactors is vital for predicting the properties and integrity of graphite as part of assessing the continued operation and life extension of nuclear reactors. The purpose of the study is to determine the electrical conductivity and thermal conductivity of low-ash medium-grained graphite’s grade graphite in the thermal column masonry of the VVR-SM research reactor in the measurement temperature range corresponding to the conditions of normal operation of the reactor to determine the service life. In this work, the change in thermal conductivity and electrical conductivity of GMZ graphite was studied, as well as for comparison of Hanford grade graphite depending on the fluence of fast neutrons and the measurement temperature. The dependence of electrical conductivity and thermal conductivity on dose and temperature has been established. It has been shown that the greater the neutron fluence, the more both the thermal conductivity and electrical conductivity of the material decreases. The service life of the thermal column has been determined.

Insight into behaviors of internal interactions and thermodynamic properties of binary mixtures composed of ether-functionalized ionic liquids and 1,4-butyrolactone or propylene carbonate

A deeper comprehension of the mechanism behind various internal interactions and their influence on system properties encourages the utilization of ionic liquid mixture systems. In this work, the excess molar volume, viscosity deviation, change of electrical conductivity, and ionicity of both binary mixtures for N-methyl-N-methoxyethylpyrrolidinium bis(trifluoromethanesulfonyl)imide ([MOEMPYrr][TFSI]) ether-functionalized ionic liquids (ILs) with 1,4-butyrolactone (GBL) or propylene carbonate (PC) were systematically studied. The specific interactions between ILs and solvent molecules were investigated by using the COSMO-RS model in terms of DFT calculation. The results indicate that [MOEMPYrr]+ tends to act as a hydrogen bond donor and [TFSI]- tends to act as a hydrogen bond acceptor, and GBL (or PC) has a strong hydrogen bond acceptance ability. Furthermore, based on the radial distribution functions (RDFs) from molecular dynamics (MD) simulations, the H1 atom in [MOEMPYrr]+, the O2 atom in [TFSI]-, the O3 atom in GBL, and the O4 atom in PC are selected as reference sites to study the interaction between cations and anions (or solvent molecules). It is found that the interaction between anions and cations in the [MOEMPYrr][TFSI] + PC system is stronger than that in the [MOEMPYrr][TFSI] + GBL system, and the interaction between cations and GBL is stronger than that between cations and PC. This result further explains why the excess molar volumes (VE) of [MOMPYrr][TFSI] + GBL binary mixtures are greater than that of [MOMPYrr][TFSI] + PC binary mixtures from a microscopic perspective.

Effect of abrupt post‐fire ash inputs on water quality and the phytoplankton community in lentic freshwaters

Abstract One of the major threats to biodiversity is changing fire regimes, particularly increasingly frequent fires, especially during the dry season. However, studies on the direct and indirect effects of fire on biotic responses in aquatic ecosystems are still scarce. In this study, we investigated how water quality and phytoplankton community structure were affected by different ash concentrations from burning vegetation of a tropical savanna. We used a microcosm experiment to simulate the aquatic ecosystem with different ash concentration scenarios and evaluated the water quality and the composition, richness and density of phytoplankton over time. We found increased total phosphorus and ammoniacal nitrogen concentrations after ash addition, in addition to changes in electrical conductivity. We identified 242 phytoplankton taxa throughout the experiment and identified changes in species composition among treatments. We identified changes in the taxonomic richness of total phytoplankton, green algae and desmids over time. The density of total phytoplankton, diatoms, green algae, desmids and cyanobacteria also changed over time. Our results suggest that ash from terrestrial fires affects water quality and phytoplankton communities depending on the proportion of ash input. Our results serve as a basis for further investigations of the effects of fire on abiotic conditions in aquatic ecosystems and their communities over long periods of time. Finally, longer‐term experiments are needed to evaluate delayed responses by the phytoplankton community.

Detection of harmful gases (NO, NO2) by GaN@MoSSe heterostructures embedded with transition metal (Cu, Fe and Mn) atoms: A DFT study

Monitoring and identifying air pollutants, such as NO and NO2, is crucial due to their detrimental impact on both the environment and human health. This work employs density functional theory (DFT) with the PBE + U functional to investigate the adsorption and sensing performance of NO and NO2 on transition metal (TM)-doped GaN@MoSSe heterostructures. The adsorption energy, charge transfer, electron localization functions, charge density difference, spin density, band gaps and density of states are analyzed. The findings reveal that a transition from physisorption to chemisorption occurs after TM atoms doping. Also, when the surface is embedded with Cu, Fe and Mn atoms, there is a significant improvement in the behavior related to gas adsorption. The bandgap and its variations lead to the change in surface electrical conductivity, thereby affecting the gas sensitivity of the adsorption system. Particularly, the CuGa-GaN@MoSSe and FeGa-GaN@MoSSe systems exhibit improved gas sensitivity toward NO due to their significant band gap reduction. Meanwhile, the CuSe−MoSSe@GaN, CuGa-GaN@MoSSe, FeGa-GaN@MoSSe and MnGa-GaN@MoSSe systems also demonstrate enhanced sensing capabilities for NO2. This work offers valuable theoretical insights for exploring the potential applications of TM-GaN@MoSSe heterostructures in gas sensing.

Determining the required amount of added solvent (H2O) to obtain a given electrolyte density

Problem. The article proposes a method for determining the required amount of water that must be added to obtain a given density of the electrolyte. Goal. The method of calculating the volume and mass of water necessary for diluting the electrolyte solution to a given density is considered. Methodology. This calculation allows, if necessary, to check the obtained results of measurements of the concentration of the electrolyte and to calculate the given density of the electrolyte taking into account the addition of the solvent (H2O). With periodic dosed replenishment of water consumed from the electrolyte, the electrolysis process occurs at a variable concentration of alkali in the electrolyte. Results. The proposed dependencies and the calculation method developed on their basis make it possible to increase the efficiency of the electrolysis process by reducing energy costs due to ensuring optimal specific conductivity of the electrolyte at a variable concentration of alkali. Originality. The resulting calculation dependence allows both during the development and operation of operating alkaline electrolyzers to calculate the current concentration and the range of changes in the concentration of alkali in the electrolyte. Practical value. The application of the obtained dependence for alkaline electrolyzers with periodic replenishment of feed water and for developed operating electrolyzers allows to analyze the nature of changes in the specific electrical conductivity of the electrolyte, i.e. evaluate the efficiency of the electrolysis process.

A finite volume approximations for one nonlinear and nonlocal integrodifferential equations

In this paper, the error analysis of the Petrov–Galerkin finite volume element method (FVEM) is investigated for a nonlinear parabolic integro-differential equation that arises in the mathematical modeling of the penetration of a magnetic field into a substance, accounting for temperature-dependent changes in electrical conductivity. Starting from Maxwell’s equations, we derive a one-dimensional model problem, which forms the basis of our analysis. Our main goal is to develop a general framework for obtaining finite volume element approximations and to study the error analysis. For simplicity, we consider only the lowest-order (linear and L-splines) finite volume elements. The novel contribution lies in the application of FVEM to this problem, leading to the establishment of an unconditionally stable numerical scheme and the derivation of optimal error estimates in the L∞(L2(Ω)) and L2(H01(Ω)) norms for both semi-discrete and linearized backward Euler fully-discrete schemes, using a generalized projection method that carefully manages the nonlinear terms. Lastly, numerical experiments are provided to support the theoretical conclusions.

KINETIC AND THERMODYNAMIC ADSORPTION STUDIES ON THE REMOVAL AND TREATMENT OF TEXTILES EFFLUENTS USING ACTIVATED CARBON DERIVED FROM DIOSPYROS MESPILLIFORMIS SEEDS.

An agricultural waste Diospyros mespiliformis seeds were treated, and activated with 30% of 0.3M sodium hydroxide base, to obtain an activated carbon employed in an adsorption process. It was utilize to treat effluent textile water sample from African Textile Manufacturers Limited in Dala, Kano State, Nigeria. Various techniques, including scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and proximate analysis were employed to investigate the adsorption process. The adsorbent was able to remove the dark red color to colorless found in textile effluents and shown a higher removal affinity for zinc ( 99.4%) and least affinity for nickel (0.11%), also Chromium (Cr) reduced by 39.4%, Copper (Cu) reduced by 20.9%, Iron (Fe) reduced by 91.9% , Manganese (Mg) reduced by 79.3%, are reduced significantly, the PH change from acidic PH 6.4 to neutral PH 7.1, turbidity decrease from 131 to 14 NTU , electrical conductivity change from 723 to 110 ?s·cm?1 .Diospyros mespiliformis seeds activated carbon was used for removal of congo red and malachite green from an aqueous solution. The effect of adsorbent dose, adsorbate concentration and contact time on the process of adsorption was investigated. The optimum dosage was found to be 0.5g had a percentage removal of 98.1% for congo red and 94.4% for malachite green. 10mg/l and 80minute was found to optimum concentration and optimum time in adsorption of congo red and malachite green. The equilibrium, kinetic and thermodynamic properties of the dyes removal were also investigated. The experimental data were modeled using linear regression method of analysis. The correlation coefficient was used as a criterion for model adequacy and acceptance. The pseudo second-order kinetic model was found to best correlate the experimental data with R2 of 0.9523 for CR and 0.9297 for MG. The experimental data were investigated at three different temperature, 305k, 325k and 335k were found to follow the Langmuir model with R2 of 0.9679, 0.9662 and 0.989 for CR and 0.9529, 0.9662 and 0.994 for MG. also were found to follow Temkinp model with with R2 of 0.9549, 0.9318 and 0.9952for CR and 0.9885, 0.9443 and 0.9209 for MG. The negative free gribbs energy indicated that the adsorption processes were spontaneously feasible. The positive values of +31.66KJ/mol and +92.3KJ/mol on both CR and MG indicate that adsorption process has been found to be endothermic in nature. The removal of congo red was found to be more spontaneous and feasible than the removal of malachite green on the adsorbent. From the study, it was deduced that the Diospyros mespiliformis seeds activated with sodium hydroxide was found to be a good adsorbent for the treatment of textile wastewater containing Congo red and Malachite green.