Cerebral Aneurysm Clip Research Articles

Transcarotid flow reversal for proximal control during cerebral aneurysm clip reconstruction: illustrative case.

Paraclinoid aneurysms can pose an operative challenge during clip reconstruction, given the complex surrounding anatomy and the aneurysmal tendency to maintain turgor despite standard approaches to proximal control. This report demonstrates the use of intraoperative retrograde arteriovenous shunting with the transcarotid artery revascularization (TCAR) system to assist in the safe clip reconstruction of an irregular paraclinoid aneurysm. A 33-year-old woman presented with perimesencephalic subarachnoid hemorrhage and was found to have an incidental 9-mm ophthalmic aneurysm. Coil embolization was not successful. During microsurgical clip reconstruction, the left common carotid artery was exposed to allow for proximal control as well as transcarotid arterial sheath placement. Flow reversal was instituted throughout the aneurysm dissection and clipping, with a visible softening of the aneurysm. Intraoperative angiography confirming successful clip reconstruction was performed utilizing the TCAR sheath. The case was complicated by the development of cerebrospinal fluid rhinorrhea postoperatively, requiring surgical repair. The patient has since made a complete recovery. Transcarotid flow reversal utilizing the TCAR system has potential for use in the surgical treatment of paraclinoid aneurysms, as it may aid in softening the aneurysm for safer dissection and clip reconstruction, protect against aneurysm-associated emboli, and provide an avenue for intraoperative angiography. https://thejns.org/doi/10.3171/CASE24330.

Comparison of TGSE-BLADE DWI, RESOLVE DWI, and SS-EPI DWI in healthy volunteers and patients after cerebral aneurysm clipping

Diffusion-weighted magnetic resonance imaging is prone to have susceptibility artifacts in an inhomogeneous magnetic field. We compared distortion and artifacts among three diffusion acquisition techniques (single-shot echo-planar imaging [SS-EPI DWI], readout-segmented EPI [RESOLVE DWI], and 2D turbo gradient- and spin-echo diffusion-weighted imaging with non-Cartesian BLADE trajectory [TGSE-BLADE DWI]) in healthy volunteers and in patients with a cerebral aneurysm clip. Seventeen healthy volunteers and 20 patients who had undergone surgical cerebral aneurysm clipping were prospectively enrolled. SS-EPI DWI, RESOLVE DWI, and TGSE-BLADE DWI of the brain were performed using 3 T scanners. Distortion was the least in TGSE-BLADE DWI, and lower in RESOLVE DWI than SS-EPI DWI near air–bone interfaces in healthy volunteers (P < 0.001). Length of clip-induced artifact and distortion near the metal clip were the least in TGSE-BLADE DWI, and lower in RESOLVE DWI than SS-EPI DWI (P < 0.01). Image quality scores for geometric distortion, susceptibility artifacts, and overall image quality in both healthy volunteers and patients were the best in TGSE-BLADE DWI, and better in RESOLVE DWI than SS-EPI DWI (P < 0.001). Among the three DWI sequences, image quality was the best in TGSE-BLADE DWI in terms of distortion and artifacts, in both healthy volunteers and patients with an aneurysm clip.

Incidence of Postoperative Cerebral Aneurysm Clip Slippage: Review of a Consecutive Case Series of 115 Clipped Aneurysms

Although delayed postoperative clip slippage has been reported in previous case reports and case series, its true incidence with high rate of follow-up imaging has not been reported. We attempted to determine the incidence of clip slippage in a cohort of consecutive aneurysm clippings. We performed a retrospective review of a prospectively maintained database of 115 consecutive saccular aneurysm clippings at a single institution. Postoperative imaging was reviewed for clip slippage within 24 hours and at 3-12 months. Eighty-six aneurysms (75.8%) were exclusively clipped with Sugitaclip (Mizuho Medical, Tokyo, Japan) Titanium II clips, 16 aneurysms were exclusively clipped with Yaşargil (Aesculap, Center Valley, PA) titanium clips (13.9%), 5 aneurysms were only clipped with Sugita aneurysm clips (4.3%), and 3 aneurysms were only clipped with Peter Lazic (Peter Lazic Microsurgical Innovations, Tuttlingen, Germany) clips (2.6%). In this cohort, 94.7% of clipped aneurysms had follow-up imaging within 24 hours, and 51.3% had delayed follow-up imaging within 3-12 months. We identified 3 cases of clip slippage in 115 consecutive aneurysm clippings, resulting in an incidence of 2.6%. The average cumulative closing force of clips per aneurysm across the study was 2.32 N, and the median number of clips placed was 1. Two of the 3 cases of clip slippage had a closing force <2.32 N and only placement of a single clip. Because our series showed a 2.6% incidence of clip slippage, clipped aneurysms should be monitored with early and delayed vascular follow-up imaging. Lower cumulative clip closing force, single clip placement, and oversized clip blade length may be risk factors for postoperative aneurysmal clip slippage.

Clinical Usefulness of Ultra-short TE MRA for Follow-up Imaging after Cerebral Aneurysm Clipping

The aims of this study were to elucidate signal pattern of cerebral aneurysm clip in brain magnetic resonance angiography (MRA) using non-contrast enhanced ultra-short echo time (UTE) sequence and to explore effective utilization of this novel technique for patients, who underwent cerebral aneurysm clipping. The clip was embedded in homemade phantom and scanned using UTE sequence. We investigated characteristic features of the artifacts derived from the clip. Besides, we compared the volume of signal loss between conventional time-of-flight (TOF) and UTE-MRA in 50 patients with the cerebral aneurysm clip. In phantom study, the clip was delineated as signal void area fully surrounded by high signal on original images. On reconstructed short-axial views for the clip, four-leaf clover pattern of artifact was observed when clip was arranged orthogonal to the static magnetic field. On the other hand, this artifact disappeared when the clip was arranged in parallel with the static magnetic field. The volume of signal loss in clinical cases was significantly reduced in UTE-MRA (P < 0.05): 1.30, 0.52-2.77 cm3 for TOF; 0.84, 0.28-1.74 cm3 for UTE (median, range). The scan time for UTE-MRA was 2 minutes and 52 seconds. To understand the characteristic feature of the artifacts from the clip could contribute to define vascular structure in image interpretation. Adding UTE-MRA to routine protocol is useful approach for follow-up imaging after cerebral aneurysm clipping with clinically acceptable prolongation of the scan time.

Late postoperative slippage of the cerebral aneurysm clip. A systematic review and meta-analysis

Late postoperative slippage of the cerebral aneurysm clip. A systematic review and meta-analysis

Probable delayed-type hypersensitivity to nickel-containing cerebral aneurysm clip associated with neurologic deficits

Probable delayed-type hypersensitivity to nickel-containing cerebral aneurysm clip associated with neurologic deficits

The Comparative Study of Microsurgical Cerebral Aneurysm Clip Implants; Titanium Clip vs. Stainless Steel Clip

ObjectiveTo perform a comparative study between two groups of populations, titanium (T) group versus stainless steel (S) group, who were clipped with titanium and stainless steel materials, respectively, the incidence of regrowth from the original aneurysms, the clip slippage, and post-clipping seizure attack were analyzed. The patients were followed more than 5 years after microsurgical cerebral aneurysms clipping.MethodsData from 1986 through 2008 were extensively reviewed on a consecutive series of 3,770 patients who referred for ruptured/unruptured cerebral aneurysms. Forty-seven patients in the S group and 48 in the T group who met inclusion criteria, were selected for this study.ResultsThe incidence of regrowth were noted that two out of total 47 patients (4.3%) in the S group, and none in the T group. The clip slippage was not observed in both groups. And there was no statistical difference (p = 0.242) in terms of regrowth between two groups. Seven out of 47 cases (14.9%) developed post-clipping seizure in the S group. On the other hand, two (4.2%) of 48 patients presented the symptom in the T group. Also, there was no significant difference (p = 0.091) between two groups.ConclusionsThe metallic types of clip employed for the microsurgical cerebral aneurysm clipping does not have any significant clinical outcome differences in this study.

Clip Blade Scissoring With Titanium Bayonet Clip in Aneurysm Surgery

Scissoring of the cerebral aneurysm clip blades is a rare but potentially devastating complication of clipping surgery and results in aneurysm neck injury inducing rupture and/or cerebral infarction. Scissoring has been reported using titanium straight clips. Here we present two unusual cases of crossing of the blades of titanium bayonet clips by a scissors-like mechanism during surgery. The present cases suggest the following points. Bayonet clips in addition to straight clips may display the scissoring phenomenon during clipping surgery. The slipped clip should be removed immediately because the scissor-like deformed aneurysm clip may slip further and result in parent artery stenosis. Scissoring tends to happen in the presence of partial arteriosclerosis of the aneurysm neck. Before a titanium clip is used to treat an aneurysm with partially arteriosclerotic neck, reducing the amount of aneurysm filling by temporary clipping of the main vessel is useful to avoid slippage phenomena.

Scissoring of cerebral aneurysm clips: mechanical endurance of clip twisting

Although the cerebral aneurysm clip "scissoring" phenomenon is known to occur due to twisting of the aneurysm clip blades during surgery, there have been few previous studies of scissoring. In the present study, we examined the in vitro endurance of clip twisting to assess clip scissoring. To evaluate the clip-scissoring effect, we measured torque at the rotating aneurysm clip head (Sugita and Yasargil clips) using our own manufactured product. A silicon sheet 1mm thick was clipped at several depths (3, 6, and 9mm), and the clip head was mechanically rotated. Straight and fenestrated clips of titanium alloy were used in the present study. Cobalt alloy straight clips were also examined. Preliminary experiments indicated that torque values during clip head rotation dropped when the blades crossed. In addition, torque values before blade crossing showed resistance to slippage of the blades. Torque values of both Sugita and Yasargil clips were directly proportional to the blade depth. There were no differences between straight and fenestrated Sugita clips. Although the torque was greater in cobalt alloy than titanium alloy Sugita clips, the torque values of Yasargil cobalt and titanium clips were identical. We found some differences in torque values during clip head rotation between Sugita and Yasargil clips. Based on the results of twisting experiments, scissoring is likely to occur when occluding the neck of the aneurysm only with the tips of long clip blades.

Optimizing computed tomography to reduce artifacts from titanium aneurysm clips: an in vitro study

Object At many institutions digital subtraction angiography remains the standard imaging procedure for the postoperative evaluation of patients following placement of a cerebral aneurysm clip largely because of the artifacts produced by the clip on computed tomography (CT). The authors evaluated the effect of various imaging parameters on the quality of 3D reconstructions from CT scans while imaging a phantom to optimize the CT angiograms. Methods Using multidetector CT scanners with submillimeter detector collimation (0.625 mm), the authors scanned a silicone phantom with attached commercial aneurysm clips. Slice thickness, reconstruction overlap, kilovolt level, milliampere level, and pitch were varied. Neuroradiologists, who were blinded to the scanning parameters, rated the reconstructions for image quality and artifact reduction. Results Images of the titanium clip using 140 kV and 380 mA with 0.625-mm overlapping reconstructed slices provided excellent 3D visualization of both the clip and the aneurysm model, even when using two adjacent clips. Conclusions Overlapping reconstructions combined with thin-section acquisition can provide detailed images of titanium clips and surrounding tissues without the use of low-pitch values.

Prototypical metal/polymer hybrid cerebral aneurysm clip: in vitro testing for closing force, slippage, and computed tomography artifact

Prototypical metal/polymer hybrid cerebral aneurysm clip: in vitro testing for closing force, slippage, and computed tomography artifact

Prototypical metal/polymer hybrid cerebral aneurysm clip: in vitro testing for closing force, slippage, and computed tomography artifact

The aim of this study was to explore the possibility that a hybrid aneurysm clip with polymeric jaws bonded to a metal spring could provide mechanical properties comparable to those of an all-metal clip as well as diminished artifacts on computed tomography (CT) scanning. Three clips were created, and Clips I and 2 were tested for mechanical properties. Clip 1 consisted of an Elgiloy spring (a cobalt-chromium-nickel alloy) bonded to carbon fiber limbs; Clip 2 consisted of an Elgiloy spring with polymethylmethacrylate (PMMA) jaws; and Clip 3 consisted of PMMA limbs identical to those in Clip 2 but bonded to a titanium spring. Custom testing equipment was set up to measure the aneurysm clip clamping forces and slippage. Clips 2 and 3 were visualized in vivo using a 64-slice CT unit, and the slices were reformatted into 3D images. According to the testing apparatus, Clip 2 had a similar closing force but less slippage than three similar commercial aneurysm clips. The artifact from the cobalt alloy spring on CT scanning largely offset the advantage of the nonmetal PMMA limbs, which created no artifact. The hybrid titanium/PMMA clip (Clip 3) created very little artifact on CT and allowed visualization of the phantom through the limbs. It is feasible to build a potentially biocompatible hybrid cerebral aneurysm clip with mechanical properties that closely resemble those of conventional metallic clips. Further testing should be directed toward establishing the reliability and biocompatibility of such a clip and optimizing the contour and surface treatments of the polymer

Optimizing computed tomography to reduce artifacts from titanium aneurysm clips: an in vitro study

At many institutions digital subtraction angiography remains the standard imaging procedure for the postoperative evaluation of patients following placement of a cerebral aneurysm clip largely because of the artifacts produced by the clip on computed tomography (CT). The authors evaluated the effect of various imaging parameters on the quality of 3D reconstructions from CT scans while imaging a phantom to optimize the CT angiograms. Using multidetector CT scanners with submillimeter detector collimation (0.625 mm), the authors scanned a silicone phantom with attached commercial aneurysm clips. Slice thickness, reconstruction overlap, kilovolt level, milliampere level, and pitch were varied. Neuroradiologists, who were blinded to the scanning parameters, rated the reconstructions for image quality and artifact reduction. Images of the titanium clip using 140 kV and 380 mA with 0.625-mm overlapping reconstructed slices provided excellent 3D visualization of both the clip and the aneurysm model, even when using two adjacent clips. Overlapping reconstructions combined with thin-section acquisition can provide detailed images of titanium clips and surrounding tissues without the use of low-pitch values.

Outcomes after cerebral aneurysm clip occlusion in the United States: the need for evidence-based hospital referral.

In an age of multimodality and multidisciplinary treatment of cerebral aneurysms, patient outcomes have improved significantly. For a number of complex surgical procedures, hospitals with high case volumes yield superior outcomes. The effect of hospital volume on the mortality rate after emergency and elective cerebral aneurysm clip occlusion in a nationally representative sample of patients is unknown. Using clinical data derived from the Nationwide Inpatient Sample for the years from 1995 through 1999, 12,023 patients who underwent clip occlusion of a cerebral aneurysm (International Classification of Diseases, Ninth Revision, Clinical Modification code 3951) were included. Patient age, comorbid conditions, nature of admission, and diagnosis of subarachnoid hemorrhage were abstracted. Hospital case volume was grouped into quartiles. Unadjusted and case-mix adjusted analyses were performed. The mean patient age was 53.2 +/- 13.5 years. The overall crude postoperative mortality rates for emergency and elective aneurysm clip occlusion were 12.2 and 6.6%, respectively. Very low volume hospitals demonstrated higher mortality rates than very high volume hospitals for both emergency (14.7 compared with 8.9%, p < 0.001) and elective (9.4 compared with 4.5%, p < 0.001) aneurysm surgery. Patient-specific predictors of death in the multivariate model were renal disease (odds ratio [OR] 3.32, p < 0.042); age (> 60 years, OR 2.36, p < 0.001; 51-60 years, OR 1.63, p < 0.001; 40-50 years, OR 1.25, p = 0.047); chronic obstructive pulmonary disease (present, OR 1.52, p < 0.001); and nature of admission (emergency, OR 1.18, p = 0.03). Provider-specific predictors of death included very low volume (OR 1.59, p < 0.001); low-volume (OR 1.37, p = 0.001); and high-volume (OR 1.45, p < 0.001) hospitals compared with very high volume hospitals. A significant volume-outcome effect exists for surgical treatment of cerebral aneurysms in the US. Factors influencing this effect should be investigated to guide future healthcare policy and evidence-based referral. Whenever possible, healthcare practitioners should refer patients to centers in which superior outcomes are consistently demonstrated.

Cell-mediated Allergy to a Cerebral Aneurysm Clip: Case Report

Cell-mediated Allergy to a Cerebral Aneurysm Clip: Case Report

Cell-mediated Allergy to a Cerebral Aneurysm Clip: Case Report

Cell-mediated Allergy to a Cerebral Aneurysm Clip: Case Report

Local cerebral blood flow with prostaglandin E1 or trimethaphan during cerebral aneurysm clip ligation

This study was performed to examine changes in local cerebral blood flow during hypotensive anaesthesia with either prostaglandin E1 (PGE1) or trimethaphan (TMP). Local cerebral blood flow (LCBF), mean blood pressure (MBP), heart rate (HR), and hourly urine output (UO) were studied in 51 patients undergoing cerebral aneurysm surgery with neuroleptanalgesia (NLA). The incidence of vasospasm after aneurysm surgery, and outcome (Glasgow Outcome Scale) at discharge were evaluated. Measurements of LCBF were made using a thermal gradient blood flow meter. The dose of PGE1 or TMP was adjusted to maintain MBP at about 70 mmHg, and LCBF was studied during and after PGE1 or TMP administration. Hypotensive drugs were discontinued at the completion of aneurysm clipping. After starting PGE1 or TMP, MBP decreased immediately, but HR did not change in either group. The LCBF decreased 30 min after the start of TMP administration and increased immediately after its discontinuation, whereas PGE1 did not affect LCBF. Urine output increased during PGE1 administration but was unchanged during TMP. Neither drug affected surgical outcome or the incidence of vasospasm. These results suggest that PGE1 may be preferable to trimethaphan for hypotensive anaesthesia in cerebral aneurysm surgery because LCBF is maintained.