Centrifugal Blood Pump Research Articles

Turbulent flow field in maglev centrifugal blood pumps of CH-VAD and HeartMate III: secondary flow and its effects on pump performance.

Secondary flow path is one of the crucial aspects during the design of centrifugal blood pumps. Small clearance size increases stress level and blood damage, while large clearance size can improve blood washout and reduce stress level. Nonetheless, large clearance also leads to strong secondary flows, causing further blood damage. Maglev blood pumps rely on magnetic force to achieve rotor suspension and allow more design freedom of clearance size. This study aims to characterize turbulent flow field and secondary flow as well as its effects on the primary flow and pump performance, in two representative commercial maglev blood pumps of CH-VAD and HeartMate III, which feature distinct designs of secondary flow path. The narrow and long secondary flow path of CH-VAD resulted in low secondary flow rates and low disturbance to the primary flow. The flow loss and blood damage potential of the CH-VAD mainly occurred at the secondary flow path, as well as the blade clearances. By contrast, the wide clearances in HeartMate III induced significant disturbance to the primary flow, resulting in large incidence angle, strong secondary flows and high flow loss. At higher flow rates, the incidence angle was even larger, causing larger separation, leading to a significant decrease of efficiency and steeper performance curve compared with CH-VAD. This study shows that maglev bearings do not guarantee good blood compatibility, and more attention should be paid to the influence of secondary flows on pump performance when designing centrifugal blood pumps.

Hemolysis analysis of centrifugal blood pump based on numerical simulation

Abstract The operation of blood pump will cause mechanical damage to red blood cells and lead to hemolysis. Based on this, CFD technology is used to simulate the three-dimensional flow field of centrifugal blood pump. According to the analysis of velocity field, pressure field and stress field; Based on the hemolysis power function model, the hemolysis performance of blood pump is predicted by Lagrange particle tracking method, and the impeller structure is adjusted to improve its flow performance and reduce the hemolysis index. The research results can provide a basis for the structural improvement and performance improvement of centrifugal heart pump.

Exploring integrated heat and mass transfer in von-Kármán dynamics involving Reiner-Rivlin fluid with regression models

The rotating disk system is widely used in several important applications, including turbomachinery design, mixing and stirring processes, centrifugal blood pumps development, optimizing electronic component, cooling efficiency, and various others. Moreover, regression models offer comprehensive and reliable prediction for important parameters in flows developed by revolving disks. This article presents similarity solutions for coupled heat and mass transfer with viscous dissipation in an inelastic non-Newtonian fluid flow across a permeable revolving disk. The inclusion of diffusion terms due to Dufour and Soret effects establishes coupling between energy and concentration equations. Temperature and concentrations at disk surface are supposed to vary quadratically along the radial direction. The impacts of MHD, heat source/sink dynamics and Joule heating effects on thermal boundary layer are also scrutinized. MATLAB's bvp5c tool, based on collocation scheme, generates numerical results. Homotopy analysis method, a widely accepted analytical solution procedure, is then applied to produce the series solution. Selection of the optimal auxiliary parameter values featured in the series solution is also included. The impact of Reiner-Rivlin fluid assumption on the torque required by the disk is assessed. Furthermore, linear and quadratic regression models are developed for the skin friction factors, Nusselt number and Sherwood number.

Optimization of a centrifugal blood pump in terms of hemolysis index and hydraulic efficiency

Optimization of a centrifugal blood pump in terms of hemolysis index and hydraulic efficiency

Numerical study of the effect of geometrical parameters of straight impellers on the flow and hemolysis performance of centrifugal blood pumps

Red blood cells are destroyed when the shear stress in the blood pump exceeds a threshold, which in turn triggers hemolysis in the patient. The impeller design of centrifugal blood pumps significantly influences the hydraulic characteristics and hemolytic properties of these devices. Based on this premise, the present study employs a multiphase flow approach to numerically simulate centrifugal blood pumps, investigating the performance of pumps with varying numbers of blades and blade deflection angles. This analysis encompassed the examination of flow field characteristics, hydraulic performance, and hemolytic potential. Numerical results indicated that the concentration of red blood cells and elevated shear stresses primarily occurred at the impeller and volute tongue, which drastically increased the risk of hemolysis in these areas. It was found that increasing the number of blades within a certain range enhanced the hydraulic performance of the pump but also raised the potential for hemolysis. Moreover, augmenting the blade deflection angle could improve the hemolytic performance, particularly in pumps with a higher number of blades. The findings from this study can provide valuable insights for the structural improvement and performance enhancement of centrifugal blood pumps.

Mixed convective viscous dissipative flow of Casson hybrid nanofluid with variable thermal conductivity at the stagnation zone of a rotating sphere

AbstractMixed convection flows across the revolving bodies have eminent applications in science and technology, such as fibre coating, polymer deposition, centrifugal blood pumps, rotatory machinery, and so forth. In the current work, magnetohydrodynamic (MHD) flow and heat transfer characteristics of Casson hybrid nanofluid (Ag/MgO as nanoparticles) over the rotating sphere at the stagnation zone are being studied. Moreover, an analysis of heat transmission is conducted by considering the influence of thermal radiation, temperature‐dependent thermal conductivity, magnetic field, and viscous dissipation. The relevant partial differential equations are reformed into ordinary differential equations by appropriate transformations, which are solved using the successive linearization method (SLM). The thermal field, velocity components in x and z directions, heat transfer rate, and skin friction coefficient are computed for various physical quantities like rotation parameter mixed convection parameter, radiation parameter, Eckert number, Casson parameter, magnetic parameter, variable thermal conductivity parameter, and so forth. The current findings align well with the literature in a limiting sense. Thermal enhancement in hybrid nanofluid is observed for the viscous dissipation parameter (Ec), thermal conductivity parameter (), and radiation parameter (Rd). The degree of heat transfer rises from 12.8% to 20% when the Casson parameter's value () increases. Also, a decrease of approximately 33% is depicted between the peak values of the velocity magnitude with an increase in rotation parameter.

Analysis of the flow field characteristics of a centrifugal blood pump in a heartbeat cycle

Blood pumps are medical devices that can temporarily or permanently replace the heart to perform the job of blood pumping. To study the internal flow field characteristics of the centrifugal blood pump, high-speed photography (HSP) images of the internal flow in the centrifugal blood pump were taken, and the internal flow field was numerically simulated. According to the heartbeat rule, the visualization experiment method and numerical simulation method for the internal flow of the centrifugal blood pump were developed. The internal flow rule of the centrifugal blood pump during a heartbeat cycle was revealed, as well as the influence of pump construction, flow rate, and other factors on the pump’s flow field. The results indicate that the flow rate and the rotor/stator interference of the blade and volute tongue cause two periodic changes in the pump pressure and velocity. One is the cycle of the heartbeat, and the other is the cycle of the blade’s rotation. The research results are of great significance in reducing the mechanical damage of blood, optimizing the structure of the pump and improving the stability of the centrifugal blood pump.

Research Progress on Influence of Centrifugal Blood Pump on Blood Injury

Centrifugal blood pumps drive blood flow by regulating blood flow rate, and have been widely used in clinical applications, including extracorporeal membrane oxygenation (ECMO), cardiopulmonary bypass (CPB), and extracorporeal circulation carbon dioxide removal (ECCO2R). However, because different structures and different forms of centrifugal pumps have different requirements for blood extracorporeal circulation in clinical application scenarios, blood pumps face different application conditions in clinical use. In this study, the effects of different structures of centrifugal pumps and different working conditions on blood damage are summarized for reference by relevant institutions and R&D personnel.

Optimization of a centrifugal blood pump designed using an industrial method through experimental and numerical study

With improved treatment of coronary artery disease, more patients are surviving until heart failure occurs. This leads to an increase in patients needing devices for struggling with heart failure. Ventricular assist devices are known as the mainstay of these devices. This study aimed to design a centrifugal pump as a ventricular assist device. In order to design the pump, firstly, the geometrical parameters of the pump, including the gap distance, blade height, and position of the outlet relative to the blade, were investigated. Finally, the selected configuration, which had all the appropriate characteristics, both hydraulically and physiologically, was used for the rest of the study. The study of the blade, as the main component in energy transfer to the blood, in a centrifugal pump, has been considered in the present study. In this regard, the point-to-point design method, which is used in industrial applications, was implemented. The designer chooses the relationship between the blade angles at each radius in the point-to-point method. The present study selected logarithmic and second-order relations for designing the blade’s profile. In total, 58 blades were examined in this study, which differed regarding blade inlet and outlet angles and the relationship between angle and radial position. ANSYS CFX 17.0 software was utilized to simulate blades’ performances, and a benchmark pump provided by the US Food and Drug Administration (FDA) was used to validate the numerical simulations. Then, the selected impeller from the numerical investigation was manufactured, and its performance was compared experimentally with the FDA benchmark pump. A hydraulic test rig was also developed for experimental studies. The results showed that among the blades designed in this study, the blade with an input angle of 45° and an output angle of 55°, which is designed to implement a logarithmic relationship, has the best performance. The selected impeller configuration can increase the total head (at least by 20%) at different flow rates compared to the FDA pump.

A multi-constituent model for assessing the effect of impeller shroud on the thrombosis potential of a centrifugal blood pump.

Centrifugal blood pumps can be used for treating heart failure patients. However, pump thrombosis has remained one of the complications that trouble clinical treatment. This study analyzed the effect of impeller shroud on the thrombosis risk of the blood pump, and predicted areas prone to thrombosis. Multi-constituent transport equations were presented, considering mechanical activation and biochemical activation. It was found that activated platelets concentration can increase with shear stress and adenosine diphosphate(ADP) concentration increasing, and the highest risk of thrombosis inside the blood pump was under extracorporeal membrane oxygenation (ECMO) mode. Under the same condition, ADP concentration and thrombosis index of semi-shroud impeller can increase by 7.3% and 7.2% compared to the closed-shroud impeller. The main reason for the increase in thrombosis risk was owing to elevated scalar shear stress and more coagulation promoting factor-ADP released. The regions with higher thrombosis potential were in the center hole, top and bottom clearance. As a novelty, the findings revealed that impeller shroud can influence mechanical and biochemical activation factors. It is useful for identifying potential risk regions of thrombus formation based on relative comparisons.

Backflow at the inlet of centrifugal blood pumps enhanced by geometrical features

Extracorporeal life support (ECLS) includes life-saving support in severe acute cardiac and/or pulmonary failure. In the past 20 years, centrifugal pumps have become the primary choice to deliver the required blood flow. Pumps of various designs, with different approved operating ranges, are today available to clinicians. The use of centrifugal pumps in the low flow condition has been shown to increase hemolytic and thrombogenic risks of the treatment. Further, low flow operation has been associated with retrograde flow at the pump inlet. In this study, experimental and numerical methods have been applied to investigate the operating conditions and fluid dynamical mechanisms leading to reverse flow (or backflow) at the inlet. Reverse flow was predominantly observed in pumps having a top shroud covering the impeller blades, showing a relation between pump geometry and backflow. The shroud divides the pump volume above the impeller into two regions, separating the swirling reverse flow migrating toward the upper pump volute from the main flow, reducing the dissipation of the vortical structures, and allowing the swirling reverse flow to reach further in the pump inlet. At the inlet, backflow was observed as stable recirculation areas at the side of the pump inlet.

Toward an Adjustable Blood Pump for Wide-Range Operation: In-Vitro Results of Performance Curve and Hydraulic Efficiency.

Rotary blood pumps in Extracorporeal Life Support (ECLS) applications are optimized for a specific design point. However, in clinical practice, these pumps are usually applied over a wide range of operation points. Studies have shown that a deviation from the design point in a rotary blood pump leads to an unexpected rise of hemolysis with corresponding clinical complications. Adjustable pumps that can adapt geometric parameters to the respective operation point are commonly used in other industrial branches, but yet not applied in blood pumps. We present a novel mechanism to adjust the impeller geometry of a centrifugal blood pump during operation together with in-vitro data of its hydraulic performance and efficiency. Three-dimensionalprinted prototypes of the adjustable impeller and a rigid impeller were manufactured and hydraulic performance and efficiency measured (n = 3). In a flow range of 1.5-9.5 L/min, the adjustable pump increased pump performance up to 47% and hydraulic efficiency by an average of 7.3 percentage points compared with a fixed setting. The adjustable pump allows customization of the pump's behavior (steepness of performance curve) according to individual needs. Furthermore, the hydraulic efficiency of the pump could be maintained at a high level throughout the complete flow range.

Extracorporeal Blood Pump driven by a Novel Bearingless Split-Tooth Flux-Reversal Motor.

This paper describes a novel bearingless split tooth flux reversal motor with integrated centrifugal blood pump. This motor has a magnet-free rotor, and is capable of operating at up to 3000 rpm with up to 100 mNm torque. The motor also has 50 N radial force capability for centering the rotor. The motor rotor is 50 mm diameter, housed in a 170mm wide stator. The motor has a novel magnetic configuration wherein the force generation is independent of the rotor angle. This allows simple radial force generation using stator-fixed currents. The motor torque is generated using commutated two-phase currents. Finite element simulations are used to optimize the design in order to achieve sufficient radial force and motor torque, while minimizing cogging torque. The design also achieves an axial passive magnetic stiffness of 5.4 N/mm, which is the constraint on axial motions of the rotor. This paper includes mechanical design and fabrication details, as well as experimental closed loop levitation and speed control performance. With an integrated impeller, the rotor and the centrifugal pump are tested by pumping fluid in a closed circuit to obtain experimental pressure-flow curves with impeller-limited performance.

Suction detection and suction suppression of centrifugal blood pump based on the FFT-GAPSO-LSTM model and speed modulation

Centrifugal blood pumps are important devices used to treat heart failure. However, they are prone to high-risk suction events that pose a threat to human health when operating at high speeds. To address these issues, a normal suction detection method and a suction suppression method based on the FFT-GAPSO-LSTM model and speed modulation were proposed. The innovation of this suction detection method lies in the application of the genetic particle swarm optimisation (GAPSO) and the fast Fourier transform (FFT) feature extraction method to the long-term and short-term memory (LSTM) model, thereby improving the accuracy of suction detection. After detecting signs of suction, the suction suppression method designed in this study based on variable-speed modulation immediately takes effect, enabling the centrifugal blood pump to quickly return to its normal state by controlling the speed. The suction detection method was divided into four steps. First, a mathematical model of the coupling of the cardiovascular system and the centrifugal blood pump was established, and a real-time blood flow curve was obtained through model simulation. Second, the signal was preprocessed by adding Gaussian white noise and low-pass filtering to make the blood flow signal close to actual working conditions while retaining the original characteristics. Subsequently, through fast Fourier transform (FFT) analysis of the processed curve, the spectral characteristics that can characterise the working state of the centrifugal blood pump were extracted. Finally, the parameters of the LSTM model were optimised using the GAPSO, and the improved LSTM model was used to train and test the blood flow spectrum feature set. The results show that the suction detection method of the FFT-GAPSO-LSTM model can effectively detect whether centrifugal blood pump suction occurs and has certain advantages over other methods. In addition, the simulation results of the suction suppression were excellent and could effectively suppress the occurrence of suction. These results provide a reference for the design of centrifugal blood pump control systems.

Effects of biventricular shunt on pump characteristics in a maglev total artificial heart.

Severe left ventricular failure can progress to right ventricular failure, necessitating alternatives to heart transplantation, such as total artificial heart (TAH) treatment. Conventional TAHs encounter challenges associated with miniaturization and hemocompatibility owing to their reliance on mechanical valves and bearings. A magnetically levitated TAH (IB-Heart) was developed, utilizing a magnetic bearing. The IB-Heart features a distinctive biventricular shunt channel situated between the flow paths of the left and right centrifugal blood pumps, simplifying and miniaturizing its control system. However, the impact of these shunt channels remains underexplored. This study aimed to investigate the effects of shunt flow on pump characteristics and assess the IB-Heart's potential to regulate flow balance between systemic and pulmonary circulation. At a rotational speed of 2000 rpm and flow rate range of 0-10 L/min, shunt flow exhibited a minor impact, with a 1.4 mmHg (1.3%) effect on pump characteristics. Shunt flow variation of about 0.13 L/min correlated with a 10 mmHg pressure difference between the pumps' afterload and preload conditions. This variance was linked to changes in the inlet flow rates of the left and right pumps, signifying the ventricular shunt structure's capacity to mirror the function of an atrial shunt in alleviating pulmonary congestion. The IB-Heart's ventricular shunt structure enables passive regulation of left-right flow balance. The findings establish a fundamental technical groundwork for the development of IB-Hearts and TAHs with similar shunt structures. The innovative coupling of centrifugal pumps and the resultant effects on flow dynamics contribute to the advancement of TAH technology.

Numerical investigation on the effect of impeller axial position on hemodynamics of an extracorporeal centrifugal blood pump

Extracorporeal centrifugal blood pumps are used to treat cardiogenic shock. Owing to the imbalanced excitation or initial assembly configurations, the variation in the impeller axial position has the potential to affect the blood pump performance. This study compared the hydrodynamics and hemolysis outcomes at different impeller axial positions via numerical simulations. The result shows that pressure difference of the blood pump decreased with increasing impeller axial position, with decreasing by 4.5% at a flow rate of 2 L/min. Under axial impeller motion close to the top pump casing, average wall shear stress and scalar shear stress reached their maximum values (64.2 and 29.1 Pa, respectively). The residence time in the impeller center hole and bottom clearance were extended to 0.5 s by increasing impeller axial position. Compared to the baseline blood pump, hemolysis index increased by 12.3% and 24.3% when impeller axial position is 2.5 and 4.0 mm, respectively. As a novelty, the findings reveal that the impeller axial position adversely affects hemolysis performance when the impeller is close to the pump casing. Therefore, in the development process of centrifugal blood pumps, the optimal axial position of the impeller must be defined to ensure hemodynamic performance.

Next Generation Development of Hybrid Continuous Flow Pediatric Total Artificial Heart Technology: Design-Build-Test.

To address the unmet clinical need for pediatric circulatory support, we are developing an operationally versatile, hybrid, continuous-flow, total artificial heart ("Dragon Heart"). This device integrates a magnetically levitated axial and centrifugal blood pump. Here, we utilized a validated axial flow pump, and we focused on the development of the centrifugal pump. A motor was integrated to drive the centrifugal pump, achieving 50% size reduction. The motor design was simulated by finite element analysis, and pump design improvement was attained by computational fluid dynamics. A prototype centrifugal pump was constructed from biocompatible 3D printed parts for the housing and machined metal parts for the drive system. Centrifugal prototype testing was conducted using water and then bovine blood. The fully combined device ( i.e. , axial pump nested inside of the centrifugal pump) was tested to ensure proper operation. We demonstrated the hydraulic performance of the two pumps operating in tandem, and we found that the centrifugal blood pump performance was not adversely impacted by the simultaneous operation of the axial blood pump. The current iteration of this design achieved a range of operation overlapping our target range. Future design iterations will further reduce size and incorporate complete and active magnetic levitation.

Use of Intracorporeal Durable LVAD Support in Children Using HVAD or HeartMate 3-A EUROMACS Analysis.

Purpose: The withdrawal of HVAD in 2021 created a concern for the pediatric population. The alternative implantable centrifugal blood pump HeartMate 3 has since been used more frequently in children. This paper analyses the outcome of children on LVAD support provided with an HVAD or HM3. Methods: A retrospective analysis of the EUROMACS database on children supported with VAD < 19 years of age from 1 January 2009 to 1 December 2021 was conducted. All patients with an LVAD and either an HVAD or HM3 were included. Patients with missing data on VAD status and/or missing baseline and/or follow up information were excluded. Kaplan-Meier survival analysis was performed to evaluate survival differences. Analyses were performed using Fisher's exact test. Results: The study included 150 implantations in 142 patients with 128 implants using an HVAD compared to 28 implants using an HM3. Nine patients (6%) needed temporary right ventricular mechanical support, which was significantly higher in the HM3 group, with 25% (p: 0.01). Patients in the HVAD group were significantly younger (12.7 vs. 14.5 years, p: 0.01), weighed less (45.7 vs. 60 kg, p: <0.000) and had lower BSA values (1.3 vs. 1.6 m2, p: <0.000). Median support time was 204 days. Overall, 98 patients (69%) were discharged and sent home, while 87% were discharged in group HM3 (p: ns). A total of 123 children (86%) survived to transplantation, recovery or are ongoing, without differences between groups. In the HVAD group, 10 patients (8%) died while on support, whereas in 12% of HM3 patients died (p: 0.7). Conclusions: Survival in children implanted with an HM3 was excellent. Almost 90% were discharged and sent home on the device.

P26: Development of Hybrid Continuous Flow Pediatric TAH Technology

Background: To address the unmet clinical need for pediatric mechanical circulatory support devices, we are developing an operationally versatile, hybrid, continuous-flow, total artificial heart (Dragon Heart). This constitutes the first device to integrate an axial and centrifugal blood pump with both pumps magnetically suspended. Methods: We employed a validated axial flow pump, and we focused here on the development of the centrifugal pump. A motor was integrated to drive the centrifugal pump and achieves a 50% reduction relative to the prior iterations. The motor design was developed using finite element analysis (COMSOL), whereas the pump design improvement was achieved by computational fluid dynamics (ANSYS fluent). A prototype centrifugal pump was constructed from bio-compatible 3-D printed parts for the housing and machined metal parts for various drive system components. Centrifugal pump testing was initially conducted using water before moving to bovine blood. Finally, the fully combined device (i.e. axial pump nested inside of the centrifugal pump) was tested to ensure proper operation. Results: The centrifugal prototype and model achieved target design requirements for pediatric MCS. We demonstrated the hydraulic performance of the two pumps operating in tandem, and found that the centrifugal blood pump performance was not adversely impacted by the simultaneous operation of the axial blood pump. Conclusion: The current iteration of the Dragon Heart design has achieved a range of operation overlapping our target range. Future design iterations will further reduce size and incorporate complete active magnetic levitation.

A comprehensive comparison of the in vitro hemocompatibility of extracorporeal centrifugal blood pumps.

Purpose: Blood damage has been associated with patients under temporary continuous-flow mechanical circulatory support. To evaluate the side effects caused by transit blood pumping, in vitro hemocompatibility testing for blood damage in pumps is considered a necessary reference before clinical trials. Methods: The hemocompatibility of five extracorporeal centrifugal blood pumps was investigated comprehensively, including four commercial pumps (the Abbott CentriMag, the Terumo Capiox, the Medos DP3, and the Medtronic BPX-80) and a pump in development (the magAssist MoyoAssist®). In vitro, hemolysis was tested with heparinized porcine blood at nominal operating conditions (5L/min, 160mmHg) and extreme operating conditions (1L/min, 290mmHg) using a circulation flow loop. Hematology analyses concerning the blood cell counts and the degradation of high-molecular-weight von Willebrand factor (VWF) during 6-h circulation were also evaluated. Results: Comparing the in vitro hemocompatibility of blood pumps at different operations, the blood damage was significantly more severe at extreme operating conditions than that at nominal operating conditions. The performance of the five blood pumps was arranged in different orders at these two operating conditions. The results also demonstrated superior hemocompatibility of CentriMag and MoyoAssist® at two operating conditions, with overall low blood damage at hemolysis level, blood cell counts, and degradation of high-molecular-weight VWF. It suggested that magnetic bearings have an advantage in hemocompatibility compared to the mechanical bearing of blood pumps. Conclusion: Involving multiple operating conditions of blood pumps in in vitro hemocompatibility evaluation will be helpful for clinical application. In addition, the magnetically levitated centrifugal blood pump MoyoAssist® shows great potential in the future as it demonstrated good in vitro hemocompatibility.