Central Region Research Articles

Study of readout system for 3He linear position sensitive detectors

This study introduces a readout system for 3He linear position-sensitive detectors (LPSDs), tailored for the Small Angle Neutron Scattering (SANS) spectrometer of the Compact Pulsed Hadron Source (CPHS) at Tsinghua University. Central to this system is the employment of a trapezoidal filter as the primary signal shaper, selected for its enhanced noise filtering capabilities and efficacy in mitigating ballistic deficit. Additionally, the integration of a digital CR filter aims to counteract baseline drift within trigger signals. This innovative architecture underwent validation via computer programs using experimental data, demonstrating superior performance in spatial resolution compared to conventional Gaussian filter-based approaches. Meanwhile, the improvement in spatial resolution comes with a narrower pulse width, promising a higher throughput at high count rates. When applied to a 16-tube detector module, the system achieved an average position resolution of 3.63 mm (FWHM) at the central region and 4.03 mm at the end regions. Furthermore, with a pusle width of 0.6 μs, the 96-tube detector array is promised to sustain a count rate over 1 Mcps.

A numerical study of Elasto-inertial particle-focusing in straight and serpentine microchannels

Microfluidic devices have gained popularity in recent years due to their low cost and simplicity. Cell focusing linked with cell counting and cell separation used in clinical tests and point-of-care devices stands towards the top of every list of microfluidic applications. To focus and manipulate particles in a Newtonian medium, inertial microfluidics has been widely used. There is a requirement to replace a significantly more efficient approach given various particle-focusing positions near the channel walls recorded by inertial microfluidics. Here, the synergetic effect of elastic and inertial forces in relatively low-concentration viscoelastic fluids was investigated numerically. Utilizing particle-focusing behavior in straight and serpentine channels with different corner angles, by applying the numerical results obtained using the developed direct numerical simulation method (DNS) for elastic and inertial forces, we created a microchannel with a remarkable performance. As the flow regime transitions to elasto-inertial, where inertial forces are comparable to elastic forces in a straight microchannel, particles tend to concentrate at the channel centerline. As the flow rate increases, however, particle defocusing develops, and shear gradient lift forces ultimately overcome elastic forces in the channel's central region. Given that fluid flows at a higher velocity in the serpentine channel with a corner angle of 75° than in other channels, the Dean drag force induced by secondary flow serves to reduce particle defocusing rate at a given flow rate, making this channel a desirable platform for Elasto-inertial microfluidics. Particle focusing in a vertical direction was noticed as a benefit of elasto-inertial microfluidics, regardless of the geometry or flow rate of the particles passing through the channel. Finally, the impact of particle diameter on focusing behavior was studied. As particle diameter decreases, focusing width decreases and the focusing band shifts to the left side of the cross-section. We expect that the numerical evaluation of using viscoelastic medium in complex geometries can contribute to accelerate the three dimensional particle-focusing mechanism and enhance the efficiency of microdevices for cell and particle manipulation.

In-plane compressive behavior of cross-laminated bamboo and timber with variable heights

This paper investigates the in-plane compressive behavior of 5-layer cross-laminated bamboo and timber (CLBT) specimens with variable heights. Five different heights of CLBT specimens, ranging from 400 mm to 3800 mm, were designed for the experiment, with conventional 5-layer cross-laminated timber (CLT) specimens used as controls. Theoretical calculations based on timber structure design codes were employed to analyze the ultimate bearing capacity, complemented by finite element simulations based on Abaqus that also explored the failure characteristics. The results indicated that CLBT wall panels had a significantly higher ultimate bearing capacity compared to those of CLT wall panels. For wall panels of around 3.0 m and 6.0 m in height, the compressive strength of the CLBT panels was approximately 65% and 40% higher than that of the CLT panels, respectively. For specimens showing buckling instability, CLBT demonstrated more concentrated failure in the end regions, contrasting with CLT, which failed primarily in the central region. The outcomes of this study clearly delineate the superiority of CLBT over CLT when used as wall panels, providing valuable references for their potential engineering applications.

Estimation and spatiotemporal analysis of actual evapotranspiration over Qinghai-Tibet Plateau using an Alpine Grassland-Adapted Priestley-Taylor model

Evapotranspiration (ET) is a crucial process in the land water cycle, energy balance, and carbon cycle, making it essential for understanding ecosystem health and climate change. The Qinghai-Tibet Plateau (QTP) is a vital contributor to the global water cycle and ecosystem, and its water resources and ecological environment are of great significance to the development and survival of Asia. To accurately estimate ET on the QTP, this paper proposes an improved Priestley-Taylor (PT) model based on shortwave infrared soil moisture index (SIMI). The model is applied to estimate ET on the QTP from 2011 to 2020, allowing for a comprehensive spatiotemporal analysis. The findings indicate that, (1) The PT-SIMI model has higher estimation accuracy than both the Modified Satellite-Based Priestley-Taylor (MS-PT) model and the Priestley-Taylor Jet Propulsion Laboratory (PT-JPL) model at most sites, particularly in alpine grasslands sites, and demonstrates a greater sensitivity in capturing changes in soil moisture; (2) the spatial distribution of ET on the QTP demonstrates a declining pattern from southeast to northwest; (3) the average ET from 2011 to 2020 remains relatively stable at 478 mm/year; (4) notable spatial variations in ET are observed across the plateau, with noticeable upward trends observed in the central and western regions, while the south central region experiencing a decreasing trend. This study provides valuable insights into the water cycle and ecological environment of the QTP and its findings can support sustainable development in the region.

Evaluating carbon emissions reduction compliance based on 'dual control' policies of energy consumption and carbon emissions in China

Dual control policies aim to effectively reduce energy consumption and carbon emission by setting targets for total volume and intensity control. With global climate change becoming increasingly serious. China, as a large energy-consuming and carbon-emitting country, faces a huge challenge to reduce carbon emissions. The transition from the “dual control of energy consumption” to the “dual control of carbon emissions” in China is necessary to optimize energy structures, promote energy conservation, reduce carbon emissions, and reach carbon neutrality. This study utilizes multi-regional input-output models to evaluate the results toward both goals from production-based, consumption-based, and income-based perspectives. The findings indicate that “dual control of carbon emissions” is a more precise approach than “dual control of energy consumption”. Some provinces have met the latter goal while still falling short of the former. Provinces having met their production-based energy intensity and carbon emission intensity targets, but having failed their consumption-based and income-based targets, are identified to develop a comprehensive and accurate assessment of these targets. A net outflow of embodied energy and carbon emissions is observed among provinces in less-developed central and southern regions to more-developed eastern and northern regions. Suggestions and policy implications based on these findings include establishing a comprehensive evaluation of energy and carbon intensity, considering both consumption-based and income-based perspectives, as well as facilitating enhanced cooperation among developed and developing provinces.

Long-range transport impact of a severe dust storm over the Yangtze River Basin region and its modeling sensitivity to dust emission scheme

Dust storms frequently occur in the spring over East Asia, affecting southern Mongolia and northeast China. An exceptionally powerful dust storm occurred in East Asia from March 14th to March 18th, 2021. To investigate the ability of climate models to simulate severe dust storms, We employed the Weather Research Forecast model coupled with chemistry (WRF-Chem) with Goddard Chemistry Aerosol Radiation and Transport (GOCART), SHAO and KOK dust emission schemes to simulate the evolution of this event and to characterize dust aerosols long-range transport. Results showed that this storm was caused by a Mongolian cyclone depicted at 850 hPa with a cold front, which swept dust aerosols southeastward across southern Mongolia to northeast China. Model evaluation with satellite-retrieved Aerosol Optical Depth (AOD) and observational PM10 concentrations revealed that the SHAO dust emission scheme performed better in simulating spatial and temporal distribution of AOD over the Gobi Desert (GD) but overestimated them over Taklimakan Desert (TD). In contrast, the GOCART dust emission scheme underestimated AOD over most areas except the Taklimakan Desert; the KOK dust emission scheme overestimated them over both TD and GD. Overall, the SHAO dust emission scheme had good performance in simulating the surface PM10 concentrations over the Yangtze River Basin (YRB) and depicted an increase in PM10 concentrations, which denoted the transport of dust aerosols over YRB. As a better description of the physical process of dust emission flux over the eastern region of the Gobi Desert, the SHAO dust emission scheme depicted well the spatial and temporal evolution of dust plume episodes, especially over northeast China and YRB. The significant differences in dust emission fluxes between the three dust emission schemes were attributed to the sensitivity of threshold friction velocity and erodibility factor. Thereunto, the SHAO dust emission scheme incorporated well soil particle size distribution and threshold velocity to produce the dust emission flux, which allowed higher dust emission flux over the eastern GD and under strong southwesterly transported dust aerosols to East Central China's region of North China Plain (NCP) and YRB. This study will help further the simulation of extreme dust events more accurately and the exploration of climate change's effect on dust events over East Asia.

Disparity in Guideline-Based Antidiabetic Drugs Prescribing for Type 2 Diabetes Patients in Primary Healthcare Facilities Across China, 2017-2019.

The purpose of this study is to evaluate the pattern, appropriateness, and cost of antidiabetic drugs prescribed for patients with Type 2 diabetes at primary healthcare facilities (PHFs) in China. We collected outpatient-visit prescriptions from 363 PHFs in 31 cities covering eastern, central, and western regions of China. The visits of adult patients with Type 2 diabetes diagnosis were collected and classified the antidiabetic medication pattern of each patient use as recommended or non-recommended according to Chinese guidelines. We then calculated the proportion of guideline-recommended patterns and the average monthly cost for each pattern, overall and by region. Of 33 519 prescriptions for Type 2 diabetes, most (73.9%) were for guideline-recommended antidiabetic treatments. The proportion of guideline-recommended prescriptions varied by region (eastern [75.9%], central [87.5%], and western [59.7%]). Metformin monotherapy was the most common guideline-recommended treatment in all three regions (eastern [20.1%], central [28.0%], and western [24.6%]). The most common non-guideline-recommended treatments were monotherapy of insulin (eastern [16.5%], central [5.1%], and western [25.7%]) and traditional Chinese antidiabetic medicines (eastern [5.6%], central [5.7%], and western [11.1%]). The average monthly costs were lower for guideline-recommended treatments compared to non-recommended treatments in all regions (eastern [13.6 ± 15.4 USD vs. 28.1 ± 22.0 USD], central [9.8 ± 10.9 USD vs. 28.7 ± 19.4 USD], and western [17.9 ± 21.4 USD vs. 30.3 ± 23.6 USD]). The majority of patients with Type 2 diabetes received guideline-recommended antidiabetic medications at PHFs in China, with only half of the prescriptions containing guideline-recommended metformin. Utilization of guideline-recommended therapies differed across regions. Tailored interventions to promote evidence-based antidiabetic prescribing are urgently needed, especially in the undeveloped western region.

Countrywide screening supports model-based predictions of the distribution of Batrachochytrium dendrobatidis in Ukraine.

The chytrid Batrachochytrium dendrobatidis (Bd) is a widespread fungus causing amphibian declines across the globe. Although data on Bd occurrence in Eastern Europe are scarce, a recent species distribution model (SDM) for Bd reported that western and north-western parts of Ukraine are highly suitable to the pathogen. We verified the SDM-predicted range of Bd in Ukraine by sampling amphibians across the country and screening for Bd using qPCR. A total of 446 amphibian samples (tissue and skin swabs) from 11 species were collected from 36 localities. We obtained qPCR-positive results for 33 samples including waterfrogs (Pelophylax esculentus complex) and fire- and yellow-bellied toads (Bombina spp.) from 8 localities. We found that Bd-positive localities had significantly higher predicted Bd habitat suitability than sites that were pathogen-free. Amplification and sequencing of the internal transcribed spacer (ITS) region of samples with the highest Bd load revealed matches with ITS haplotypes of the globally distributed BdGPL strain, and a single case of the BdASIA-2/BdBRAZIL haplotype. We found that Bd was non-randomly distributed across Ukraine, with infections present in the western and north-central forested peripheries of the country with a relatively cool, moist climate. On the other hand, our results suggest that Bd is absent or present in low abundance in the more continental central, southern and eastern regions of Ukraine, corroborating the model-predicted distribution of chytrid fungus. These areas could potentially serve as climatic refugia for Bd-susceptible amphibian hosts.

Transport enhancement in the laminar rotating disk boundary layer

Enhanced momentum and heat transport in a three-dimensional rotating disk boundary layer due to the consideration of a wavy disk surface is an already known fact in the literature. Such a transport enhancement is primarily associated with two fundamental attributes of the wavy disk: the increased surface area and the enhanced convection due to the surface undulations. However, there exists no further information about their individual role, mutual interaction, and individual share in enhancing the convective transport in the rotating disk boundary layer. This study aims to investigate these facts in detail by considering radially heterogeneous different wavy configurations on the disk surface. It is revealed that the said attributes contribute non-trivially to enhance the transport phenomena. Their impactful role is identified due to the strengths of circumferential and crossflow velocity components, the magnitude of flow swirl angle, and hence due to the coefficients of skin friction and their inter relationship. In this regard, a fundamental benchmark regarding the relative strength of the two coefficients of skin friction is identified from the flat disk case. Decisive observations regarding the impact of surface undulations and the increased surface area of the wavy disk on the enhanced convective transport are made with the aid of this benchmark. It is observed that the enhanced transport phenomena, especially the heat transfer, mainly depend upon the further dominance of the circumferential velocity component. In the situations of increased dominance of rotational flow Kw>Kf, the increased convection and surface area collectively contribute to enhance the thermal transport while in a reverse situation Kw<Kf the convection contributes adversely by even reducing the impact of the increased surface area. In the neutral situation where the dominance of rotational velocity is neither increased nor decreased (i.e., Kw≈Kf), any increase in the transport phenomena is wholly due to the increased surface area. Therefore, the presence of surface undulations or increase in surface area is not the only criterion for an optimum rise in the transport phenomena, rather the impact of surface undulations on the velocity profiles is important which is manipulated due to their positioning on the disk surface. It is observed that the presence of surface undulations in the central and intermediate regions on the disk surface causes to increase the gradients of the crossflow velocity while their presence in the near rim location causes to enhance the gradients of the circumferential velocity. Thus, the configurations that have higher undulations in the near rim region outperform the other configurations.

Sidewall influence of varying free stream Mach number in ramp induced shock wave boundary layer interactions

This study investigates the 3D effects introduced by the end walls for an aspect ratio 1 in ramp-induced shock wave boundary layer interactions. The simulations are performed using symmetry boundary condition in spanwise at free-stream Mach numbers in three dimensions. The simulations are done using an in-house compressible supersonic solver “OpenSBLIFVM”[1]. Two free stream Mach numbers 2.5, and 3 are utilised in the current work, the simulated results are compared with the aspect ratio 1 simulations of Mangalagiri and Jammy [2]. The inflow is initialized with a similarity solution; its Reynolds number based on the boundary layer thickness is adjusted such that the Reynolds number at the starting of the ramp is kept at 3×105 for all simulations. From the results, it is evident that the introduction of sidewalls resulted in a shorter centerline separation length when compared with the 2D simulations. This is contradictory to the results at Mach 2 by [2]. The vortex observed at Mach 2 by Mangalagiri and Jammy [2], in the central separation region, has vanished with increasing the free-stream Mach number. Also, the topology of interaction has changed from owl-like separation of the second kind to the first kind when the freestream Mach number has increased from 2 to 2.5. It can be concluded that, the topology of interaction is key to the increase or decrease of the central separation length when compared to 2D.

Imaging analysis of pneumonic plague infection in Xizang, China: a case report and literature review

BackgroundPlague is an acute infectious disease caused by the Yersinia pestis. Historically, it has been a major pandemic with high mortality rates, known as the “Black Death” in the 14th century, which resulted in millions of deaths in Europe. With increasing economic prosperity, more and more people are traveling to Xizang. However, this trend also hides significant safety hazards. Currently, there are few recent reports on plague, especially those with imaging manifestations available. In this study, we report the detailed clinical and radiological data of the patient with pneumonic plague in Xizang, China, in 2023.Case presentationWe report a case of pneumonic plague in Xizang, which occurred in a herdsman living in an area where dead marmots were found. The patient presented with symptoms such as fever, hemoptysis, dyspnea and coma. Chest computed tomography (CT) scans showed multiple nodules distributed in the central regions of lung lobes, consolidation distributed in secondary pulmonary lobules, and had a gravity-dependent distribution pattern. These imaging findings were consistent with pulmonary hemorrhage and diffuse alveolar damage. Despite emergency treatment, the patient died within 48 h of admission. Through retrospective medical history investigation, laboratory examination and autopsy, the final diagnosis was confirmed as pneumonic plague.ConclusionPneumonic plague is the most deadly infectious disease, and its pathological features mainly include damage to the alveoli, pulmonary hemorrhage, and pulmonary edema. Corresponding to CT, it manifests as acute and rapidly progressing pneumonia, alveolar damage, and pulmonary hemorrhage. The value of this article lies in the completeness and typicality of the imaging data, vivid hand-drawn illustrations of transmission pathways, and comprehensive literature review, all of which serve to enhance public understanding of plague and play an important warning role.

An Interactive Behavior of Soil Moisture Influences the Concentration of Arsenic in the Acidic Soil of the Plow Layer of the Central Region of Thailand

An Interactive Behavior of Soil Moisture Influences the Concentration of Arsenic in the Acidic Soil of the Plow Layer of the Central Region of Thailand

A multi-mode stretching apparatus for in situ synchrotron x-ray scattering of polymer materials.

A compact and versatile tensile apparatus for polymer materials is designed and fabricated. Three distinct stretching modes are developed: constant speed, cyclic, and sinusoidal, with adjustable speeds ranging from 0.001 to 120 mm/s. To capture the true strain of the central region, a high-speed camera has been integrated into the apparatus. The temperature of the sample chamber is controlled by flowing air, enabling a homogeneous temperature in the range of RT ∼200 °C. The apparatus is particularly suitable for a synchrotron beamline. The structural evolution of natural rubber during sinusoidal stretching is investigated by in situ wide-angle x-ray scattering. Scattering patterns, force, clamp position, and sample images are saved simultaneously during stretching. Notably, the results reveal a sinusoidal variation in the crystallinity of crosslinked natural rubber when a sinusoidal strain was applied to the sample. The integration of advanced measurement techniques and controlled experimental conditions ensures the acquisition of reliable and accurate data, providing valuable insights into the structural evolution of materials under dynamic deformation conditions.

VLBA Astrometry of the Fastest-spinning Magnetar Swift J1818.0−1607: A Large Trigonometric Distance and a Small Transverse Velocity

In addition to being the most magnetic objects in the known Universe, magnetars are the only objects observed to generate fast-radio-burst-like emissions. The formation mechanism of magnetars is still highly debated and may potentially be probed with the magnetar velocity distribution. We carried out a 3 yr long astrometric campaign on Swift J1818.0−1607, the fastest-spinning magnetar, using the Very Long Baseline Array. After applying the phase-calibrating 1D interpolation strategy, we obtained a small proper motion of 8.5 mas yr−1 mag and a parallax of 0.12 ± 0.02 mas (uncertainties at 1σ confidence throughout the Letter) for Swift J1818.0−1607. The latter is the second magnetar parallax and is among the smallest neutron star parallaxes ever determined. From the parallax, we derived the distance 9.4−1.6+2.0 kpc, which locates Swift J1818.0−1607 at the far side of the Galactic central region. Combined with the distance, the small proper motion leads to a transverse peculiar velocity v⊥=48−16+50 km s−1—a new lower limit to magnetar v ⊥. Incorporating previous v ⊥ estimates of seven other magnetars, we acquired v⊥=149−68+132 km s−1 for the sample of astrometrically studied magnetars, corresponding to the three-dimensional space velocity ∼190−87+168 km s−1, smaller than the average level of young pulsars. Additionally, we found that the magnetar velocity sample does not follow the unimodal young pulsar velocity distribution reported by Hobbs et al. at >2σ confidence, while loosely agreeing with more recent bimodal young pulsar velocity distributions derived from relatively small samples of quality astrometric determinations.

Exploring the Archives: A Search for Novae in UVIT Snapshots of M31

Extensive multiwavelength studies of novae have been carried out in our galaxy and in M31 for decades. However, UV studies of extragalactic novae are limited, especially those in quiescence. For the first time, we present a UV catalog of novae in M31 using the archival AstroSat Ultraviolet Imaging Telescope (UVIT) imaging data. We used two image subtraction techniques to retrieve objects located deep into the M31 central region. We have found 42 novae in total in the UVIT images, 15 of which have been detected in multiple filters in the far-ultraviolet (FUV) and near-ultraviolet. The novae detected at quiescence show signatures of accretion disk from their UV spectral energy distributions, whereas those in the outburst phase show signatures of a pseudo-photosphere. A few novae were also detected in multiple epochs. Some show a near-constant FUV magnitude at quiescence, while others caught near the outburst reveal pre-eruption dips in their light curves. We conclude with a discussion on the significance of UV surveys in illuminating theoretical predictions for novae systems, including detecting the elusive early UV flash.

Female leaders as environmental saviors: Tackling urban pollution in Chinese cities

In the Chinese political context, local government officials have substantial influence over the implementation of policies. The approach to urban environmental management varies significantly between female and male officials, which in turn affects governance outcomes differently. Consequently, the gender of local officials plays a crucial role in shaping urban environmental conditions. This study investigates the impact of female officials on urban environmental pollution in China over the period from 2003 to 2018. Utilizing data from the China Urban Statistical Yearbook combined with individual profiles of officials at the prefecture level, the analysis reveals a notable decrease in urban environmental pollution associated with female leadership. Notably, the effect is more pronounced among younger female officials compared to their older counterparts, and those with higher education levels are particularly effective in curbing pollution emissions. The pollution abatement effect of female officials is found to be stronger in the central regions compared to the eastern and western regions. The robustness of these findings is confirmed through checks against alternative explanatory variables, permutation tests, and treatment effect analyses. Overall, this research contributes new perspectives on management strategies that can sisgnificantly improve urban environmental quality in China.

Prevalence and Classification of Pediatric Neuromuscular Disorders in the Central Region of Portugal.

Neuromuscular disorders are a group of rare heterogenous diseases with profound impact on quality of life, for which overall pediatric prevalence has rarely been reported. The purpose of this study was to determine the point prevalence of pediatric neuromuscular disorders and its subcategories in the central region of Portugal. Retrospective case identification was carried out in children with neuromuscular disorders seen between 1998 and 2020 from multiple data sources. Demographics, clinical and molecular diagnoses were registered. On January 1, 2020, the point overall prevalence in the population <18 years of age was 41.20/100 000 (95% confidence interval 34.51-49.19) for all neuromuscular disorders. The main case proportion were genetic disorders (95.7%). We found a relatively higher occurrence of limb-girdle muscular dystrophies, congenital myopathies, and spinal muscular atrophy and a slightly lower occurrence of Duchenne muscular dystrophy, hereditary spastic paraparesis, and acquired neuropathies compared to previous studies in other countries. Molecular confirmation was available in 69.5% of pediatric neuromuscular patients in our cohort.Total prevalence is high in comparison with the data reported in the only previous study on the prevalence of pediatric neuromuscular disorders in our country. Our high definitive diagnostic rate underscores the importance of advances in investigative genetic techniques, particularly new sequencing technologies, in the diagnostic workup of neuromuscular patients.

Assessing the Carbon Footprint of Viticultural Production in Central European Conditions

A number of factors will increasingly play a role in the sustainability of wine production in the coming period. The current situation suggests that the analysis of energy consumption and greenhouse gas (GHG) emissions will play a particularly important role. The so-called carbon footprint, expressed in CO₂ equivalents, is used to express the sum of GHG emissions. This study presents an analysis of vine cultivation in a particular Central European region, with the main focus on quantifying the inputs, yield, fuel consumption, and GHG emissions. The emphasis was placed on conventional, integrated, and ecological production systems of growing, evaluated with the help of the developed AGROTEKIS version 5 software. A total of 30 wine-grower entities in the Morava wine-growing region, the subregion Velké Pavlovice, in the Czech Republic weather climate, were included in the input data survey. By analyzing the aggregated values, the real savings in energy and curbing of CO2 emissions of vineyards could be observed, relating to individual work procedures with lower energy demand used in the vineyard treatment as well as the amounts and doses of agrochemicals used. The average values of the total impacts did not show any statistically significant differences between the conventional (971 ± 78 kg CO2eq·ha−1·year−1) and integrated production systems (930 ± 62 kg CO2eq·ha−1·year−1), whereas the values for the ecological production system were significantly higher (1479 ± 40 kg CO2eq·ha−1·year−1). The results show that growing vines under ecological production conditions generates a higher proportion of the carbon footprint than under conventional production conditions. Overall, the best results can be achieved in an integrated production system.

Digital economy empowered entrepreneurship

PurposeAs an important engine of economic growth, the digital economy is bringing new opportunities for the promotion of entrepreneurship. However, key questions regarding the extent of the effect of the digital economy on entrepreneurship remain unanswered. This study examines how the digital economy influences entrepreneurship in China using provincial data from 2011–2020, applying convergence tests and spatial econometric models.Design/methodology/approachBased on theoretical analysis and using macro provincial data covering the period of 2011–2020, we adopt a diversified empirical analytical method and apply a combination of the convergence trend test, spatial auto correlation test, and spatial Durbin model to test the research hypotheses.FindingsFirst, there is spatial correlation between the digital economy and entrepreneurship. Second, the overall trend of China’s digital economy shows s convergence, with the whole country and the eastern region showing absolute β convergence and the whole country as well as the central and western regions showing β conditional convergence. Third, the digital economy can significantly promote entrepreneurship and has spatial spillover effects. Moreover, higher education has a negative moderating effect on the process of digital economy empowering entrepreneurship.Research limitations/implicationsStudying the spatially correlated impacts of the digital economy on entrepreneurship enhances our understanding of its contribution to economic growth. Policy-makers can use these findings to develop targeted digital infrastructure investments in lagging provinces, guide entrepreneurs to better grasp the opportunities of the digital economy, and provide support for innovation and entrepreneurship. The findings also could offer Chinese experience that can be used to guide developing countries in utilizing the digital economy to enable entrepreneurship.Originality/valueThis paper expands and enriches the analytical focus on digital economy-empowered entrepreneurship and complements the current theoretical research on the moderating effect of the digital economy in empowering entrepreneurship.

Scientific (Astro) tourism activities in Armenia and in South West and Central Asian region

Scientific Tourism activities have been initiated in a number of countries during the recent decades. Armenia was among the first countries developing Scientific Tourism and most probably the first to develop Astro Tourism. We were the first to introduce the term “Astronomical Tourism” (or “Astro Tourism”). This includes visits to astronomy-related sites (astronomical observatories, astronomical institutes, astronomy-related university departments, ancient sky/astronomy-related sites, medieval universities, planetariums, space/astronomy museums, etc.) but not only. The organization of astronomical meetings, schools, camps and other events with involvement of many visitors, we also consider as Astro Tourism activities. We give an overview of our activities, including the main project; development of Astro Tourism in the SWCA region. A detailed study of Astro Tourism sites in Armenia, Georgia, Iran, Kazakhstan, Tajikistan, Turkey and (in addition) Uzbekistan was carried out, namely, modern astronomical observatories and institutes, ancient astronomy-related sites, medieval universities, planetariums, astronomy/space museums, etc. A webpage was built representing Astro Tourism in SWCA region. We also discuss the Scientific Tourism and Tourism in general as disciplines for studies and not only as service. We will share our experience on Scientific/Astro tourism activities and discuss how different items may be implemented in different regions.