Central Longitudinal Axis Research Articles

Experimental study on transverse fire source and blockage locations influence on tunnel fire temperature distribution

Previous research has commonly assumed that tunnel fire blockage occurs at the central longitudinal axis of tunnels. However, fires may arise at different points within tunnels, each with various distances from the tunnel sidewall. The study aimed to investigate the distribution of ceiling temperature fields across various scenarios of blockage and transverse fire source locations by conducting a sequence of fire experiments within a reduced-scale 1:10 horseshoe-shaped tunnel model. The findings indicate that at sufficiently low ventilation velocities (v’≤0.19), the maximum ceiling temperature rise in the tunnel remains virtually unchanged regardless of the locations of blockage and transverse fire source. For higher ventilation velocities (v’>0.19), the maximum ceiling temperature rise diminishes with greater blockage-fire source distance. Additionally, the maximum ceiling temperature rise increases as the distance between the sidewall and the fire source diminishes. Furthermore, a new model has been formulated to forecast the dimensionless maximum ceiling temperature rise, incorporating both blockage and transverse fire locations.

Relative profile measurements in 1.5T MR-linacs: investigation of central axis deviations

Objective. In 1.5 T MR-linacs, the absorbed dose central axis (CAX) deviates from the beam's CAX due to inherent profile asymmetry. In addition, a measured CAX deviation may be biased due to potential lateral (to the beam) effective point of measurement (EPOML) shifts of the detector employed. By investigating CAX deviations, the scope of this study is to determine a set ofEPOMLshifts for profile measurements in 1.5 T MR-linacs.Approach. The Semiflex 3D ion chamber and microDiamond detector (PTW, Germany) were considered in the experimental study while three more detectors were included in the Monte Carlo (MC) study. CAX deviations in the crossline and inline profiles were calculated based on inflection points of the 10×10 cm2field, at five centers. In MC simulations, the experimental setup was reproduced. A small water voxel was simulated to calculate CAX deviation without the impact of the detector-specificEPOMLshift.Main results. All measurements were consistent among the five centers. MC-based and experimental measurements were in agreement within uncertainties. Placing the microDiamond in the vertical orientation does not appear to affect the detector'sEPOML, which is on its central longitudinal axis. For the Semiflex 3D in the crossline direction, the CAX deviation was 2.3 mm, i.e. 1 mm larger than the ones measured using the microDiamond and simulated considering the ideal water detector. Thus, anEPOMLshift of 1 mm is recommended for crossline profile measurements under both Semiflex 3D orientations. For the inline profile, anEPOMLshift of -0.5 mm was determined only for the parallel configuration. In the MC study, CAX deviations were found detector- and orientation-dependent. The dead volume is responsible for theEPOMLshift only in the inline profile and under the parallel orientation.Significance. This work contributes to data availability on the correction or mitigation of the magnetic field-induced changes in the detectors' response.

Persistent Targeting DNA Nanocarrier Made of 3D Structural Unit Assembled from Only One Basic Multi-Palindromic Oligonucleotide for Precise Gene Cancer Therapy.

Construction of a simple, reconfigurable, and stimuli-responsive DNA nanocarrier remains a technical challenge. In this contribution, by designing three palindromic fragments, a simplest four-sticky end-contained 3D structural unit (PS-unit) made of two same DNA components is proposed. Via regulating the rotation angle of central longitudinal axis of PS-unit, theorientedassembly of one-component spherical architecture is accomplished with high efficiency. Introduction of an aptamer and sticky tail warehouse into one component creates a size-change-reversible targeted siRNA delivery nanovehicle. Volume swelling of 20 nm allows one carrier to load 1987 siPLK1s. Once entering cancer cells and responding to glutathione (GSH) stimuli, siPLK1s are almost 100% released and original size of nanovehicle is restored, inhibiting the expression of PLK1 protein and substantially suppressing tumor growth (superiorto commercial transfection agents) in tumor-bearing mice without systemic toxicity.

Quantifying anterior pelvic roll during total hip arthroplasty in the lateral decubitus position.

Unintended pelvic positional change is an acknowledged intra-operative problem for hip arthroplasty, seen commonly with procedures performed in the lateral position. If unrecognised, such changes can dramatically alter final acetabular component anteversion potentially resulting in suboptimal construct performance. It has previously been suggested that pelvic roll of just 13° may be enough to place an otherwise perfectly orientated cup outside of conventional ± 10° safe zones. Using the real-time tracking capacity of a commercially available optical navigation system, we aimed to accurately quantify pelvic roll occurring during total hip arthroplasties (THAs) performed in the decubitus position. Prospectively collected data for 107 consecutive, unilateral, THAs were interrogated to determine the magnitude of pelvic movement around a central longitudinal axis (i.e. AP roll). Correlation statistics with patient age and body mass index (BMI) were also calculated. A mean pelvic roll of 9.5° was observed, being anterior in 96% of cases. Of these, 18.3% of hips had a magnitude of roll greater than 13°. There were no statistically significant independent correlations observed between age (p = 0.87) or BMI (p = 0.59) and mean roll. Errors in achieving acetabular target version may result in numerous post-operative concerns including instability/dislocation, bearing wear, squeaking, range-of-movement limitation and increased revision rate. In a general cohort, our findings suggest a mean anterior pelvic roll during THA of nearly 10°. Without purposeful correction, this may cause substantial deviation from intended target positions. Future work is indicated to map changing pelvic roll during THA which is likely to follow a nonlinear trajectory. Level ofevidence: IV. .

Poster 351: Relation Between Femoral Anterior Cruciate Ligament Tunnel Orientation and Anterolateral Ligament Tunnel Collision in a 3D-CT Model

Poster 351: Relation Between Femoral Anterior Cruciate Ligament Tunnel Orientation and Anterolateral Ligament Tunnel Collision in a 3D-CT Model

A geometric morphometric approach to investigate primate proximal phalanx diaphysis shape.

Current approaches to quantify phalangeal curvature assume that the long axis of the bone's diaphysis approximates the shape of a portion of a circle (included angle method) or a parabola (second-degree polynomial method). Here we developed, tested, and employed an alternative geometric morphometrics-based approach to quantify diaphysis shape of proximal phalanges in humans, apes and monkeys with diverse locomotor behaviors. 100 landmarks of the central longitudinal axis were extracted from 3D surface models and analyzed using 2DGM methods, including Generalized Procrustes Analyses. Principal components analyses were performed and PC1 scores (>80% of variation) represented the dorsopalmar shape of the bone's central longitudinal axis and separated taxa consistently and in accord with known locomotor behavioral profiles. The most suspensory taxa, including orangutans, hylobatids and spider monkeys, had significantly lower PC1 scores reflecting the greatest amounts of phalangeal curvature. In contrast, bipedal humans and the quadrupedal cercopithecoid monkeys sampled (baboons, proboscis monkeys) exhibited significantly higher PC1 scores reflecting flatter phalanges. African ape (gorillas, chimpanzees and bonobos) phalanges fell between these two extremes and were not significantly different from each other. PC1 scores were significantly correlated with both included angle and the a coefficient of a second-degree polynomial calculated from the same landmark dataset, but had a significantly higher correlation with included angles. Our alternative approach for quantifying diaphysis shape of proximal phalanges to investigate dorsopalmar curvature is replicable and does not assume a priori either a circle or parabola model of shape, making it an attractive alternative compared with existing methodologies.

Measurement of tibial tuberosity-trochlear groove distance by MRI: assessment and correction of knee positioning errors.

The tibial tuberosity-trochlear groove (TTTG) distance varies with the position of the knee in the MR or CT scanner. We present and assess a simple method for adjustment of adduction or abduction of the knee. MRI of the knee encompassing a three-dimensional (3D) sagittal sequence including ≥ 8cm of the proximal tibia was analyzed (29 females, 17 males; median age 45years). Using 3D visualization software, the central longitudinal axis of the proximal tibia (TA) was constructed, and the TTTG distance was measured before and after alignment of the TA. Observer reliability was assessed with inter- and intra-class correlation coefficient (ICC) and Bland-Altman plots. Adduction of the knee occurred in 26 examinations, mean 2.7° (range 0.0° to 9.4°), and abduction in 20 examinations, mean 2.6° (range 0.0° to 7.2°). Following adjustment, the mean TTTG distance increased 2.4mm (range 0.0 to 6.7mm) in the knees positioned in adduction and decreased 2.3mm when in abduction (range 0.0 to 5.5mm). The correlation coefficient (r2) between the deviation in adduction and abduction and the difference between TTTG unadjusted and adjusted was r2 = 0.96. ICCs were excellent, but limits of agreement were close to ± 3mm. Measurement of the TTTG distance by MRI is influenced by a systematic technique-dependent error caused by knee positioning in adduction or abduction. We suggest a simple method for adjusting the positioning.

Personalized Three-Dimensional Printing Pedicle Screw Guide Innovation for the Surgical Management of Patients with Adolescent Idiopathic Scoliosis

To assess the safety and efficacy of patient-specific three-dimensional (3D) rapid-prototype printing technology for pedicle screw insertion in patients with adolescent idiopathic scoliosis (AIS). The 3D pedicle screw guides were produced after selecting the fixation points for all individual levels to be used intraoperatively. Preoperative computed tomography images recreated 3D bone models of each vertebra specific to each patient. Safe pedicle trajectories were determined in all 3 planes on these models. 3D printed guides were modeled according to these trajectories and manufactured with a biocompatible material. Postoperatively, all screws were evaluated and scored with computed tomography as class 1 (accurate), class 2 (inaccurate), or class 3 (deviated). The mean angle between the inserted pedicle screw and the intended trajectory, and the mean distance between the central longitudinal axis of a screw and pedicle were also measured. A total of 134 screws were inserted. On the concave and convex sides, the mean medial malposition was 0.5 ± 0.8 and 0.4 ± 0.6 mm, the mean lateral malposition was 1.4 ± 2.3 and 0.8 ± 1.3 mm, angle between the inserted pedicle screw and the intended trajectory was 4.2 ± 4.6 and 4.3° ± 6.0°, and distance between the central longitudinal axis of a screw and pedicle was 1.5 ± 2.1 and 0.9 ± 1.2 mm, respectively. A total of 117 screws were regarded as class 1, 14 as class 2, and 3 as class 3. Of all screws inserted, 92.5% achieved positional accuracy. There were no screw-related complications. This is one of the initial reports to note the novel design and implementation of patient-specific 3D pedicle screw guides for adolescent idiopathic scoliosis surgery. Our pilot study shows that the use of these low-cost personalized 3D guides is completely safe and effective in both convex and concave sides of the curves.

Electron microscopy and tomography reveal that sodium 2-naphthalene sulfonate incorporated into perming solutions swells and tilts trichocyte intermediate filaments causing straightening of curly Japanese human hair.

A new hair-care process has been specifically developed for the straightening of curved Japanese woman's hair . The process included sodium 2-naphthalene sulfonate (SNS) in the reduction and oxidation steps of a conventional perming process. Our objective was to develop an understanding of how this process caused hair straightening by measuring the changes to morphology and ultrastructure between untreated, conventionally permed and SNS permed hair. Untreated and SNS permed Merino wool fibres were used to confirm structural changes. Japanese hair samples were measured for single-fibre curvature before and after perming treatments. A silver staining method was developed to stain hair fibres without changing fibre curvature so that transmission electron microscopy could be used to measure changes in the lateral dimensions of all structural components from the cellular to protein filament level. Electron tomography determined intermediate filament slopes and slope changes after SNS perming relative to the central longitudinal axis of the fibre. SNS perming was found to cause greater lateral swelling than conventional perming of: the paracortical cells of wool; the cuticle, the cuticular cell membrane complex and the macrofibrillar centre-to-centre distance of hair; and of the intermediate filaments in wool and hair. In curved hair, SNS perming caused the intermediate filaments of the helical macrofibrils to simultaneously swell and to tilt further, resulting in the slight longitudinal contraction of the macrofibrils. The overall swelling and tilting was greatest in the helical macrofibrils of Type B cortical cells predominately located in the convex fibre half. The presence of a higher percentage of helical macrofibrils in the convex fibre half than in the concave fibre half caused a contraction differential between the two halves leading to straighten of the curved fibre. A mechanical model was proposed to explain how SNS perming straightened curly hair. The effects of conventional and SNS perming on the morphological and ultrastructural components of curved Japanese hair and high-curl Merino wool fibres have given clear insights into understanding the mechanism of fibre curvature change.

Effect of Outer Surface Sealing Treatment on the Reduction of Surface Check Occurrence During the Drying of Center-Bored Round Timber

A significant amount of time and energy is required to dry green timber with a large cross-section. Due to long-lasting internal moisture gradients, internal stress is high during the drying of large cross-sectional timber, and the potential for check occurrence is significant. Although many researchers have aimed to develop a method for drying large pieces of wood without the occurrence of drying defects, a procedure for rapidly drying wood without cracks has not yet been developed. In the present study, an outer surface sealing method and center-boring process (i.e., drilling a hole along the central longitudinal axis) was developed to dry timber with a large cross-section without the occurrence of checks. The proposed center-boring procedure reduces the movement of heat and moisture inside the wood and expedites the drying process by sustaining a small MC gradient. Moreover, the outer surface sealing treatment changes the drying stress direction and controls check occurrence. By kiln drying center-bored (80-mm diameter) and outer-surface-sealed round timber pitch pine (Pinus rigida) with an initial MC of 30% and an outer diameter of 140 mm, a final MC of 6% was obtained within 40 hours without the occurrence of any drying defects.

Investigation of the dose distribution for a cone beam CT system dedicated to breast imaging

Cone-beam breast Computed Tomography (bCT) is an X-ray imaging technique for breast cancer diagnosis, in principle capable of delivering a much more homogeneous dose spatial pattern to the breast volume than conventional mammography, at dose levels comparable to two-view mammography. We present an investigation of the three-dimensional dose distribution for a cone-beam CT system dedicated to breast imaging. We employed Monte Carlo simulations for estimating the dose deposited within a breast phantom having a hemiellipsoidal shape placed on a cylinder of 3.5 cm thickness that simulates the chest wall. This phantom represents a pendulant breast in a bCT exam with the average diameter at chest wall, assumed to correspond to a 5-cm-thick compressed breast in mammography. The phantom is irradiated in a circular orbit with an X-ray cone beam selected from four different techniques: 50, 60, 70, and 80 kVp from a tube with tungsten anode, 1.8 mm Al inherent filtration and additional filtration of 0.2 mm Cu. Using the Monte Carlo code GEANT4 we simulated a system similar to the experimental apparatus available in our lab. Simulations were performed at a constant free-in-air air kerma at the isocenter (1 μGy); the corresponding total number of photon histories per scan was 288 million at 80 kVp. We found that the more energetic beams provide a more uniform dose distribution than at low energy: the 50 kVp beam presents a frequency distribution of absorbed dose values with a coefficient of variation almost double than that for the 80 kVp beam. This is confirmed by the analysis of the relative dose profiles along the radial (i.e. parallel to the “chest wall”) and longitudinal (i.e. from “chest wall” to “nipple”) directions. Maximum radial deviations are on the order of 25% for the 80 kVp beam, whereas for the 50 kVp beam variations around 43% were observed, with the lowest dose values being found along the central longitudinal axis of the phantom.

Descrição fonética eletropalatográfica de fones alveolares

To describe the articulation of the Brazilian Portuguese, by examining the tongue-palate contact in the production of consonantal phones. The electropalatography (EPG) of the alveolar consonants of the Brazilian Portuguese produced by an individual with typical speech was used, considering the alveolar, post-alveolar, palatal, and velar rates, as well as the percentage of activated contacts at the point of maximum constriction, and the visual inspection of palatograms. As expected, it was observed that all the examined phones have more contact in the alveolar region at the point of maximum constriction. The phones /t/, /d/ and /n/ showed more alveolar contact, with total obstruction of the air stream; the fricative phones /s/ and /z/ were characterized by the absence of contact at the central longitudinal axis; the lateral phone /l/ did not present contact at the lateral longitudinal axis, and the tap /[symbol: see text]/ showed not only few tongue-palate contacts but it was also produced in the shortest duration time. The electopalatography allowed a detailed description of the extension of the tongue-palate contact in the different alveolar phones of the Brazilian Portuguese and how they occur.

Modelling Of Heat Conduction Along Vein Walls In Endovenous Laser Treatment

Modelling Of Heat Conduction Along Vein Walls In Endovenous Laser Treatment

Preliminary liver dose estimation in the new facility for biomedical applications at the RA-3 reactor

As a part of the project concerning the irradiation of a section of the human liver left lobe, a preliminary estimation of the expected dose was performed. To obtain proper input values for the calculation, neutron flux and gamma dose rate characterization were carried out using adequate portions of cow or pig liver covered with demineralized water simulating the preservation solution. Irradiations were done inside a container specially designed to fulfill temperature preservation of the organ and a reproducible irradiation position (which will be of importance for future planification purposes). Implantable rhodium based self-powered neutron detectors were developed to obtain neutron flux profiles both external and internal. Implantation of SPND was done along the central longitudinal axis of the samples, where lowest flux is expected. Gamma dose rate was obtained using a neutron shielded graphite ionization chamber moved along external surfaces of the samples. The internal neutron profile resulted uniform enough to allow for a single and static irradiation of the liver. For dose estimation, irradiation condition was set in order to obtain a maximum of 15 Gy-eq in healthy tissue. Additionally, literature reported boron concentrations of 47 ppm in tumor and 8 ppm in healthy tissue and a more conservative relationship (30/10 ppm) were used. To make a conservative estimation of the dose the following considerations were done: (i). Minimum measured neutron flux inside the sample (∼5×10 9 n cm −2 s −1) was considered to calculate dose in tumor. (ii). Maximum measured neutron flux (considering both internal as external profiles) was used to calculate dose in healthy tissue (∼8.7×10 9 n cm −2 s −1). (iii). Maximum measured gamma dose rate (∼13.5 Gy h −1) was considered for both tumor and healthy tissue. Tumor tissue dose was ∼69 Gy-eq for 47 ppm of 10B and ∼42 Gy-eq for 30 ppm, for a maximum dose of 15 Gy-eq in healthy tissue. As can be seen from these results, even for the most conservative case, minimum tumor dose will be acceptable from the treatment point of view, which shows that the irradiation conditions at this facility have quite good characteristics for the proposed irradiation.

Morphogenesis of the bovine rete testis: the intratesticular rete and its connection to the seminiferous tubules.

The development of the intragonadal rete testis and the establishment of the connection between seminiferous and straight testicular tubules was studied using ultrastructural and histochemical methods in 60 bovine embryos and fetuses ranging from day 39 through day 225 post conceptionem. The methodology included a modified acetylcholinesterase (AChE) reaction as a selective marker for pre-Sertoli cells and a modified microsomal aminopeptidase (MAP) reaction as a selective marker for the epithelia of rete testis and straight testicular tubules. Between 40 and 45 days, the rete testis is predominantly an extratesticular rete situated in the cranial peduncle of the gonadal fold and in broad contact with the pro/mesonephric giant corpuscle. During this period, the intragonadal rete enters the gonad proper from its craniodorsal pole and extends into the cranial fourth of the testis. Between 60 and 110 days the rete testis attains its definitive position, extending into the central longitudinal axis as far as to the caudal fourth of the testis. For the caudal expansion of the rete testis the preceding proliferation of the mediastinal stroma is an important prerequisite. In the 40 to 45-day-old embryo the area of the testicular cords may be divided into two zones. A narrow outer zone contains plate-like cords with a thick diameter, and a larger central zone is filled with a network of thinner cords. Only the thick outer cords transform into the permanent seminiferous tubules, whereas the thinner cords in the central zone are transitory structures that disappear between 45 and 110 days. One important function of these transitory cords is to establish a continuous system of basal laminae that allows a direct connection between the central ends of the growing seminiferous tubules and the peripheral extensions of the rete testis (future straight testicular tubules). The first true straight testicular tubules become visible between 85 and 110 days. Due to a strong proliferation of the tubulus rectus-cells the straight testicular tubules elongate continuously, and the border between the rete system and the seminiferous tubules is slowly shifted towards the testicular periphery. This shift is not restricted to the prenatal period, but proceeds until after birth. At the cytological level, the formation and elongation of the straight testicular tubules is effected by proliferating cells that advance along the continuous basal lamina into the area of the seminiferous tubules. The pre-Sertoli and germ cells in this zone of invasion are separated from each other and overgrown by the tubulus rectus-cells. Exposed to the special milieu of the straight testicular tubules, pre-Sertoli and germ cells apparently cannot survive and finally disappear.

Intraobserver and interobserver measurements of the anorectal angle and perineal descent in defecography.

Anorectal angle and perineal descent can be measured either by drawing a line defined by the impression of the puborectalis muscle and the tangential of the posterior rectal wall (Method A) or by drawing a straight line at the level of the posterior rectal wall parallel to the central longitudinal axis of the rectum (Method B). The aim of this study was to assess the reproducibility of measuring anorectal angle and perineal descent by two different methods according to intraobserver and interobserver measurement and to evaluate which method yields more consistent results. Five physicians who have had an average of 1.3 years (range, 6 months to 1.5 years) experience in defecographic measurement drew both lines on 63 randomly selected defecographic films and measured anorectal angle and perineal descent by the two methods. The defecographic parameters were measured twice by each observer during a three-week interval. To avoid potential bias, one physician who did not participate in either measurement of perineal descent or anorectal angle performed all data collection. Intraobserver and interobserver agreement was quantified using Shrout and Fleiss intraclass correlation coefficients. The mean and range of intraclass correlation coefficients for intraobserver agreement of measuring anorectal angle and perineal descent by Method A were 0.71 (0.6-0.78) and 0.89 (0.74-0.97), respectively, whereas with Method B the coefficients were 0.81 (0.73-0.89) and 0.93 (0.89-0.99), respectively. Regarding the interobserver agreement of the five observers, the mean coefficients for measurement of both anorectal angle and perineal descent by both methods showed similar agreement levels (0.88 and 0.98 by Method A and 0.89 and 0.97 by Method B). The mean (+/- standard deviation) values of anorectal angle and perineal descent found by Method B were significantly larger than those found by Method A (103.3 degrees +/- 19.6 and 6.56+/-3.20 cm and 91.1 degrees +/- 25.6 and 5.64+/-3.42 cm, respectively; P<0.001). Intraobserver and interobserver intraclass correlation coefficients of anorectal angle and perineal descent, which were measured by both methods, were more than 0.60, indicating that both methods are reliable and consistent for measurement of anorectal angle and perineal descent. However, centers should consistently use the same line for measurement of anorectal angle and perineal descent because of the statistically significant differences between the two methods and the possibility of inconsistent results.

Ciliogenesis in photoreceptor cells of the tree shrew retina.

Transmission electron microscopy of the retinal cones from several prenatal, young postnatal and adult tree shrews (Tupaia belangeri) reveals that the centrioles, from which the ciliary precursors of the outer segments grow out, are not transported into a pre-existing inner segment, but are positioned under the apical plasma membrane of cone precursor cells all through the inner segment formation. Ciliogenesis starts before or on embryonic day 20 and thus precedes initial formation of the inner segment by 20 days, which is half the gestation period. Thus, the maturation of the outer segment covers a considerably longer period than has been previously described. Published observations from other mammals can be interpreted as conforming with the situation in Tupaia. In other vertebrates, compared to mammals, marked heterochronies do occur. In Tupaia, the centrioles and the cilium are located close to the central longitudinal axis of the photoreceptor precursor cell from the 20-day-old embryo to the 5-day-old juvenile. In this position the microtubule apparatus originating from the centrioles should be most effective in transporting the mitochondria into the inner segment. In the 12-day-old tree shrew, when transport of the mitochondria into the inner segment has been completed, centrioles and cilium have shifted into an eccentric position and the light-collecting megamitochondria have approached the disks of the outer segment. This eccentric position is maintained in all later developmental stages. In certain of the retinal areas of the adult Tupaia, the connecting cilia of neighbouring cones are always positioned on the same side of the inner segments.

Ultrasonic diagnostic transducer array with elevation focus

An ultrasonic diagnostic transducer array is provided for providing electronic focusing in the longitudinal plane and elevational focusing. Elements of the array are subdiced in the elevational direction to provide subelements with aspect ratios varying in proportion to their distance to the central longitudinal axis of the array. Such variation affords varying electro-mechanical coupling coefficients to the subelements such that the intensity of the transmitted energy is centered about the central longitudinal axis. In a second embodiment elements exhibit extensions in the elevational direction which vary in proportion to their displacement from the longitudinal center of the array. The extended elements are acoustically separated into subelements in the elevational direction to provide elevational focusing or spatial compounding of the transmitted acoustic energy.

The application of PIXE to the mapping of contaminants deposited on a monolithic automotive catalytic converter

Automotive catalytic converters lose activity whilst in service. The degree of deactivation depends upon a number of factors including contamination by residues of additives or trace elements in fuel and/or engine oil, which generally reduces the surface area of the catalyst. In this initial investigation, PIXE was used to map contaminant deposition at three points along each of the central longitudinal axis and a parallel axis located closer to the side of a single monolith. This monolith was selected because it was physically undamaged and exhibited low surface area (<2 m 2 g −1) at the front and reasonable surface area (>10 m 2 g −1) towards the rear. A total of 20 elements were identified. The contaminants P, K, Ca, Zn and Pb were deposited in greater concentration towards the front of the monolith on both axes. Si may also be a contaminant; it is unexpectedly deposited more uniformly along the central axis than along the parallel side axis where it appears to decrease linearly from front to rear. Degraded precision was obtained for Al and Si in samples that were heavily contaminated.

Mass transfer characteristics for a rotating cup-like cylinder

A numerical study is made of flow and mass transfer characteristics for a cup-like cylinder, which rotates steadily about its own central longitudinal axis. This study simulates the earlier mass transfer experiment of Sparrow and Chaboki, which provided only the averaged value of Sherwood number. Comprehensive numerical solutions have been obtained for the Navier-Stokes equations over an extended range of Reynolds numbers. Numerically-constructed flow visualizations exhibit the structures of three-component velocity and concentration fields. The patterns of meridional flows, which are directly responsible for convective transport, are analyzed. The distributions of azimuthal flow are illustrated. Plots of the local Sherwood number at the inner surface of the cup are given. Physically plausible descriptions are presented Gf the local mass transfer characteristics for both cases of a transferring base endwall and a non transferring base endwall. The numerical results of the cavity-average Sherwood number are consistent with the previous experimental data.