Source Of Cellulose Research Articles

Seaweed-derived etherified carboxymethyl cellulose for sustainable tissue engineering

Biodegradability, biocompatibility, abundant supply from renewable sources, and affordability are the outstanding properties of cellulose that have prompted substantial studies into its potential in biomedical applications. Beyond terrestrial sources of cellulose, seaweeds have attracted much attention as a potential source of cellulose because they are widely available. Cellulose and its byproducts may be extracted from various macroalgae species, including red, green, and brown algae. The extracted cellulose's qualities vary depending on the algae species, age, and extraction process utilized. Cellulose's characteristics are enhanced through chemical modifications, specifically etherification and esterification, which substitute functional groups for hydroxyl groups, yielding a range of products, including cellulose acetate (CA), cellulose nitrate, cellulose sulfate, methylcellulose, and carboxymethyl cellulose (CMC). The ability to modify CMC characteristics for particular applications is explored through techniques including grafting processes mixing, and cross-linking with other polymers. Moreover, tissue engineering is given significant consideration in the growing use of CMC and its altered forms in biological applications. These alterations allow for the production of scaffolds that promote tissue regeneration and cell proliferation, enabling CMC-based scaffolds for various tissue engineering uses. This review provides a comprehensive overview of CMC's properties, modifications, and potential in tissue engineering.

Preparation of Lyocell Fibers from Solutions of Miscanthus Cellulose.

Both annual (cotton, flax, hemp, etc.) and perennial (trees and grasses) plants can serve as a source of cellulose for fiber production. In recent years, the perennial herbaceous plant miscanthus has attracted particular interest as a popular industrial plant with enormous potential. This industrial crop, which contains up to 57% cellulose, serves as a raw material in the chemical and biotechnology sectors. This study proposes for the first time the utilization of miscanthus, namely Miscanthus Giganteus "KAMIS", to generate spinning solutions in N-methylmorpholine-N-oxide. Miscanthus cellulose's properties were identified using standard methods for determining the constituent composition, including also IR and atomic emission spectroscopy. The dry-jet wet method was used to make fibers from cellulose solutions with an appropriate viscosity/elasticity ratio. The structural characteristics of the fibers were studied using IR and scanning electron microscopy, as well as via X-ray structural analysis. The mechanical and thermal properties of the novel type of hydrated cellulose fibers demonstrated the possibility of producing high-quality fibers from miscanthus.

Sustainable Polyamide Composites Reinforced with Nanocellulose via Melt Mixing Process

Introduction of biomass-based nanofillers into the polyamide matrix may represent a sustainable approach for the development of high-performance engineering plastics. From this standpoint, nanocellulose, derived from various cellulosic sources, has attracted a great deal of attention because of is exceptional mechanical properties, lightweight nature, and biodegradability, which presents significant advantages over conventional inorganic fillers. However, a technical challenge arises in the industrially favorable melt processing of polyamides and nanocellulose. This challenge is associated with the thermal degradation of nanocellulose at high processing temperatures, as well as the strong tendency of nanocellulose to aggregate within the polymer matrix. This review examines recent developments to address these issues. Key approaches based on the surface treatment of nanocellulose as well as optimization of processing conditions are discussed in detail, which can provide insights on the development of nanocellulose-reinforced polyamide composites.

Exploring the reclamation pathway science of Beachwood powder for pharmaceutical acetaminophen drug effluent management.

High effective low-cost substance derived from agriculture-based waste towards a circular economy concept showed a significant green approach for pharmaceuticals uptake in aqueous solution. Beachwood sawdust was used as the source of cellulose based adsorbents. Cellulose is isolated from the waste and in parallel magnetite nanoparticles are prepared by the simple co-precipitation technique and the two substances are mixed in various proportions to be acetaminophen adsorbent. Characteristics of the prepared magnetite (M)/sawdust (SD) composite in various proportions (M:SD (1:1), M:SD (1:2), M:SD (1:3), M:SD (1:5) and M:SD (2:1) were assessed using scanning electron microscope (SEM) transmission electron microscope (TEM) and X-ray diffractometer (XRD) which revealed the presence magnetite and cellulose. Also, for the object of recoverable adsorbent, vibrating sample magnetometer (VSM) of the adsorbent is investigated to evaluate its sustainability. The highest removal rate was associated with M:SD (1:2) compared to the other composites and the pristine magnetite or sawdust materials within 2 hours of isotherm time. The adsorption parameters are optimized and the maximal yield is attained at pH (7.0), adsorbent dose of 2.0 g/L at room temperature. The adsorption matrix is following Langmuir model and fitted to the second-order kinetic model. The process is exothermic in nature and highlighted physisorption tendency. The highest monolayer adsorption uptake was investigated at 7.0 mg/g which corresponds to the M:SD (1:2) adsorbent.

Hydrothermal alkaline treatment of lignocellulosic biomass for microcrystalline cellulose generation at subcritical water

Like lignocellulosic biomass, wood waste sawdust is rich in cellulose and can potentially be used as a source of microcrystalline cellulose (MCC) production via removal of hemicellulose and lignin constituents. Under hydrothermal alkaline treatment (100 to 140 °C), the breaking in the linkages of lignin and hemicellulose groups may happen, resulting in the solid residue, which is known as a cellulose-rich solid product. Results of FTIR analysis indicated that the removal of non-cellulosic constituents improved with increasing operating temperature and/or the prolonged treatment time. The XRD diffractogram pattern proved that improving the operating parameters (temperature and/or time) may also improve the crystallinity index of the solid product. On the contrary, the yield of the solid product decreases with increasing operating temperature and/or the prolonged treatment time.

Utilization of Forest Residues for Cellulose Extraction from Timber Species in the High Montane Forest of Chimborazo, Ecuador

The present study explored the extraction of cellulose from forest residues of four timber species, namely Cedrela montana Moritz ex Turcz, Buddleja incana Ruiz & Pav, Vallea stipularis L. f. and Myrsine andina (Mez) Pipoly, in the high montane forest of Chimborazo province, Ecuador, for the sustainable utilization of leaves, branches, and flowers. An alkaline extraction method was used on the residues without the need for prior degreasing. An ANOVA analysis was applied to evaluate significant differences in cellulose extraction yields among the species’ residues. The characterization techniques used were Fourier transform infrared spectroscopy (FTIR) and polarized light optical microscopy, which confirmed the successful extraction of cellulose with characteristics comparable to standard cotton cellulose and other traditional species. The results showed significant variations in cellulose yield among the species, with Vallea stipularis L. f achieving the highest yield of 80.83%. The crystallinity of the samples was clearly evidenced by the polarity of the light in the samples during microscopy, demonstrating that the residues can be a viable and sustainable source of cellulose, contributing to a circular economy and reducing the environmental impact of forest waste.

Optimization and Modification of Bacterial Cellulose Membrane from Coconut Juice Residues and Its Application in Carbon Dioxide Removal for Biogas Separation

Driven by environmental and economic considerations, this study explores the viability of utilizing coconut juice residues (CJRs), a byproduct from coconut milk production, as a carbon source for bacterial cellulose (BC) synthesis in the form of a versatile bio-membrane. This work investigates the use of optimization modeling as a tool to find the optimal conditions for BC cultivation in consideration of waste minimization and resource sustainability. Optimization efforts focused on three parameters, including pH (4–6), cultivation temperature (20–30 °C), and time (6–10 days) using Design Expert (DE) V.13. The maximum yield of 9.31% (g/g) was achieved when the cultivation took place at the optimal conditions (pH 6, 30 °C, and 8 days). This approach aligns with circular economy principles, contributing to sustainable resource management and environmental impact reduction. The experimental and predicted optimal conditions from DE V.13 were in good agreement, validating the study’s outcomes. The predictive model gave the correlations of the optimal conditions in response to the highest yield and maximum eco-efficiency. The use of prediction modeling resulted in a useful tool for forecasting and obtaining guidelines that can assist other researchers in calculating optimal conditions for a desired yield. Acetylation of the BC resulted in cellulose acetate (CA) membranes. The CA membrane exhibited the potential to separate CO2 from a CH4/CO2 mixed gas with a CO2 selectivity of 1.315 in a membrane separation. The promising gas separation results could be further explored to be utilized in biogas purification applications.

Exploring the effects of cellulose sources on silver reduction and the bacterial removal of nanocellulose-based hydrogel beads

With water access challenged, there is a need to develop efficient and sustainable alternatives for water purification. Here, cellulose nanofibrils (CNFs) isolated from three source materials (softwood, soybean hulls and oat straw) were compared for the generation of hydrogels beads, and compared as support and reducing agent for silver nanoparticles formation. The silver-functionalized hydrogel beads (Ag-CNFs) were characterized, and the surface energy and specific surface area were evaluated. Antimicrobial testing was conducted to assess the efficacy of the Ag-CNFs against E. coli. The results showed that the Ag-CNFs had a higher specific surface area and lower surface energy compared with unmodified CNFs. Softwood-based Ag-CNFs exhibited the highest silver content and specific surface area, while the soybean hull based showed the highest hydrophobic character. The silver-functionalized soybean hull beads (Ag-sbCNF) showed the highest efficacy in reducing the growth of bacteria. Overall, this study highlights the potential of silver-functionalized CNFs hydrogel beads as a promising environmentally friendly and sustainable material for water filtration and disinfection. The findings also suggest that lower surface energy of the Ag-CNFs play an important role in their antimicrobial effect on tested water by enabling shorter retention, providing useful insights into the design of future water filtration materials.

Harvesting nature’s treasure from agricultural biomass: Spatholobus parviflorus unveiled as a source of nano-scaled crystalline cellulose

Harvesting nature’s treasure from agricultural biomass: Spatholobus parviflorus unveiled as a source of nano-scaled crystalline cellulose

Biomass-based perovskite/graphene oxide composite for the removal of organic pollutants from wastewater

Water pollution is a critical issue that affects both human health and the environment. Biomass-based LaFeO3 is prepared by the microwave-assisted method using rice straw as a cellulose source. Then LaFeO3/graphene oxide (GO) composite is prepared by ultrasonication to facilitate the perovskite-GO binding. Raman and FTIR spectra of the prepared composite identify the presence of the perovskite, biochar, cellulose and GO oxide phases and proves the surface functional groups interactions. Transmission electron microscope image shows that the GO sheets are homogeneous covered with the perovskite nanoparticles. The adsorption performance of the LaFeO3/GO composite for the removal of methylene blue (MB) and congo red (CR) dyes from aqueous solution is optimized. Adsorption follows pseudo 2nd order kinetic model and Freundlich isotherm, with maximum adsorption capacities of 319.5 and 416.7 mg/g for MB and CR, respectively. These values are higher than those reported for magnetic GO composites, indicating the excellent adsorption ability of the proposed perovskite/GO composite. A thermodynamic study shows that the adsorption of MB is exothermic, while it is endothermic for CR and combines physisorption and chemisorption characteristics for both dyes. The proposed adsorbent shows a good performance in the presence of NaCl interferent, with the possibility of regeneration and efficient successive reuse.

A soft processing technology for the extraction of cellulose from plant residues and agri-food wastes

In this study, cellulose was extracted from giant cane (GC), Posidonia oceanica seagrass (PO), coffee silverskin (CS), and brewer's spent grain (BSG) as alternatives to conventional sources of cellulose. The extraction protocol involved three steps: i) hemicellulose and lignin removal through alkaline hydrolysis in a 5% (w/v) NaOH solution (solid-to-liquid ratio = 1:100 g/mL, T = 25 °C, t = 2 h, ω = 300 rpm), ii) removal of organic compounds and ashes through a 95% (v/v) ethanol solution (solid-to-liquid ratio = 1:25 g/mL, T = 25 °C, t = 0.5 h, ω = 500 rpm), and iii) double bleaching in a 1% (w/v) acidic (pH = 4) NaClO2 solution (solid-to-liquid ratio = 1:50 g/mL, T = 90 °C, t = 1.5 h, ω = 500 rpm). Yield, purity, crystallinity degree, and morphology of cellulose extracted through a soft-chemical cascade process were assessed by gravimetric, infrared (FT-IR), nuclear magnetic resonance (NMR) spectroscopy, X-ray diffraction (XRD), and scanning electron microscopy (SEM) analyses. Averaged cellulose extraction yields of 36.4, 38.6, 23.1, and 22.2% for GC, PO, CS, and BSG were obtained, respectively. All cellulose samples had high purity, though lower than the ultra-pure bacterial cellulose, which was due to the slight contamination from unremoved hemicellulose and lignin residues. Cellulose samples exhibited similar chemical features and the typical fibril-like morphology of microcrystalline cellulose (6–13 μm in width). The versatility of the proposed extraction procedure supports the sustainable conversion of low-cost organic biomasses to valuable products with manifold industrial applications (e.g., food packaging).

Emulsifying properties of cellulose nanocrystals with different structures and morphologies from various solanaceous vegetable residues

The stems of solanaceous vegetables with attractive source of cellulose, have caused severe environmental problems as agricultural residues. For the reutilization of the residues, this study isolated cellulose nanocrystals (CNs) from the stems of tomato, eggplant, and pepper to explore their applications in Pickering emulsions. Detailed analyses of the crystalline structure and morphology revealed differences in their emulsifying properties. Tomato stem CNs had higher crystallinity of 82.1 % and a short, straight rod-like shape with a low aspect ratio of 8.0, while eggplant and pepper CNs were long, curved whisker-like fibers with lower crystallinities of 75.3 % and 75.4 %, respectively. Tomato stem CNs exhibited the best emulsifying properties, attributed to their relatively higher crystallinity and larger crystal brick size enhancing amphiphilicity, along with their lower aspect ratio improving interface coverage, which resulted in stable emulsions across different temperatures, pH levels, and ionic strengths. This study enhances our understanding of how the structure and morphology of CNs influence their emulsifying properties, thereby contributing to the promotion of agricultural waste reutilization.

Physical and chemical treatments in obtaining and purifying Kombucha SCOBY Cellulose

SCOBY cellulose (CS) is a biopolymer with exceptional physical properties, serving as a source of fiber, water retention capacity, crystallinity, and purity. Its potential as a byproduct of kombucha production and a source of bacterial cellulose (BC) has been a subject of exploration. This study aims to gather information from experimental studies in the scientific literature on various methods of CS extraction, processing, and purification, and their impact on microscopic, macroscopic structure, and functional characteristics. The purification treatments for CS, as described in the literature, include immersion in deionized, distilled, or sterile water, sodium hydroxide, hydrogen peroxide, and sodium hypochlorite under agitation or static mode at different temperatures (23ºC, 30ºC, 50ºC, 80ºC, 90ºC, 110ºC) and under variable contact times with the substance chosen for treatment (1, 2, 20, 24 hours to 3 days). Alkaline treatments on SCOBY cellulose enhance extensibility, viscoelasticity, absorptivity, tensile strength, heat stability, and remove microorganisms, sugars, and other components of the culture medium adhered to the cellulose. With CS being obtained at a low cost and low complexity in the fermentation process, and the potential for less polluting treatments, it presents a sustainable process and source of CB that can be applied in a variety of industries, particularly in the exciting field of food.

Application of scoby bacterial cellulose as hydrocolloids on physicochemical, textural and sensory characteristics of mango jam.

The scoby pellicle of symbiotic culture of bacteria and yeast is a by-product from kombucha fermentation. While a portion is used as starter culture, the remainder is often discarded, yet it can be a valuable source of bacterial cellulose. Scoby from black, green and oolong tea kombucha fermentation was assessed for its hydrocolloid effects in mango jam-making through evaluation of physicochemical, textural and sensory characteristics. Quality of jam was significantly improved with water activity reduction up to 22.22% to 0.679, moisture content reduction up to 37.06% to 19.92%, and a pH drop up to 5.9% to 3.19 with the use of 20 to 100 g kg-1 scoby. In colour analysis, presence of scoby led to a brighter jam due to higher values from 30.98 to a range of 31.82 to 40.83. Texture of jam with scoby gave higher gel strength and adhesiveness, with the most prominent effects from the black tea kombucha. Overall acceptability in sensory test scoring was above 70% on a nine-point hedonic scale with the 40 g kg-1 green tea kombucha scoby jam chosen as the most preferred. Scoby gave significant contributions to jam stability, appearance and texture, showing potential as a clean-label food ingredient. © 2024 Society of Chemical Industry.

Oil palm frond leaves (OPFLs), a high recalcitrant biomass as an alternative cellulose source for glucose conversion

Among the oil palm biomass, oil palm frond leaves (OPFLs) are under-valued since they can be classified as a high recalcitrance feedstock due to the high lignin and hemicellulose content. This work proposes a new way of using OPFLs as alternative cellulose sources for glucose conversion by an application of various pre-treatments at varying parameters. From green pre-treatment, steam explosion (SE) is much more effective in disrupting the OPFLs structure in contrast to hydrothermal (HT) pre-treatment, by a vast dissolution of hemicellulose and depolymerization of lignin. The pre-impregnation with H2SO4 prior to steam explosion was beneficial to enhance the hemicellulose removal up to 89.94 %. The 2D-HSQC NMR analysis divulged the reduction of ß-O-4 linkage and S/G value after the SE and HT pre-treatment, verifying the degradation of lignin-carbohydrate linkage in OPFLs. Meanwhile, the dilute NaOH pre-treatment enhanced the delignification by 87.14 %. SEM analysis revealed a well-disrupted structure of pre-treated OPFLs exposing a higher cellulosic fraction, whereas SEC analysis divulged a decreasing pattern of degree of polymerization of cellulose. The enzymatic analysis revealed that pre-treated OPFLs yielded higher glucose ranging from 29.81 % to 49.98 % w/w, which was ∼3-fold higher than raw OPFLs (14.31 % w/w). A maximum cellulose digestibility (100 %) was achieved by steam-exploded OPFLs after 72 h of enzymatic hydrolysis. This suggests the potency of various pre-treatments to enhance enzymatic saccharification of OPFLs producing a higher glucose yield.

Dissolution of denim waste in N-methyl morpholine-N-oxide monohydrate for fabrication of regenerated cellulosic film: Experimental and simulation study

Despite the significant amount of denim waste and its potential as a cellulose source, its use has been neglected. This study uses N-methyl morpholine-N-oxide, an eco-friendly solvent, to dissolve denim (including 100 % cotton) and create a denim film. Achieving a 10 % denim record solubility, a cellulosic film was also fabricated for comparison. Characterisation techniques were applied, and molecular dynamics simulations explored intramolecular interactions and the influence of indigo dye on dissolution process. FTIR spectra indicated no chemical reactions during dissolution and regeneration, though a shift in OH stretching suggested a change in crystallinity, confirmed by XRD results showing decreased crystallinity and a structural shift from cellulose I to cellulose II. 13C NMR analysis revealed disruptions in interchain hydrogen bonds after regeneration. TGA results showed lower decomposition temperatures for both films compared to the powders. Testing mechanical properties showed the denim film had higher elongation at break but lower tensile strength than the cellulose film. MD simulations indicated indigo dye did not significantly affect fundamental interactions but decreased denim solubility by reducing the diffusion coefficient. Rheological tests supported the simulation results, showing higher viscosity and molecular weight for the denim solution compared to cellulose.

Preparation and characterization of microcrystalline cellulose from rice bran.

Rice bran, a by-product of rice processing, has not been fully utilized except for the small amount used for raising animals. The raw material source requirements of microcrystalline cellulose are becoming increasingly extensive. However, the characteristics of preparing microcrystalline cellulose from rice bran have not been reported, which limits the application of rice bran. Microcrystalline cellulose was obtained from rice bran by alkali treatment, delignification, bleaching and acid hydrolysis. The morphology, particle size distribution, degree of polymerization, crystallinity, and thermal stability of rice bran microcrystalline cellulose were analyzed. The chemical compositions, scanning electron microscopy and Fourier-transform infrared analysis for rice bran microcrystalline cellulose showed that the lignin and hemicellulose were successfully removed from the rice bran fiber matrix. The morphology of rice bran microcrystalline cellulose was shown to be of a short rod-shaped porous structure with an average diameter of 65.3 μm. The polymerization degree of rice bran microcrystalline cellulose was 150. The X-ray diffraction pattern of rice bran microcrystalline cellulose showed the characteristic peak of natural cellulose (type I), and its crystallization index was 71%. The rice bran microcrystalline cellulose may be used in biological composites with temperatures between 150 °C and 250 °C. These results suggest the feasibility of using rice bran as a low-price source of microcrystalline cellulose. © 2024 Society of Chemical Industry.

High Yield Synthesis of Cellulose Nanocrystals From Avicel by Mechano‐Enzymatic Approach

AbstractCellulose nanocrystals are an important class of bio‐based crystalline nanostructures, finding application in several technological fields, including paper and textile coating, biocomposite engineering, biocatalysts immobilization, etc. This study explores enzymatic hydrolysis of Avicel, using endoglucanase from Aspergillus niger, to find an environmentally friendly method to extract cellulose nanocrystals from cellulose sources. Enzymatic hydrolysis has the advantage of reduced energy consumption and higher environmental friendliness compared to acid hydrolysis. In this work, we report for the first time very high nanocrystals yield by combining mechanical pretreatment of the cellulose starting material with a ball miller and endoglucanase hydrolysis, as a result of an extensive optimization of reaction conditions. In particular, a ball milling pretreatment carried out for 50 minutes at 3 Hz, allowed to isolate enzymatic CNCs with 76 % yield and with crystallinity as high as 75 %. The materials were characterized by X‐Ray diffractometry, attenuated total reflectance Fourier transform infrared (ATR‐FTIR) spectroscopy, dynamic light scattering, zeta potential and field emission scanning electron microscopy (FE‐SEM). Their characteristics were compared with the properties of sulfated CNCs, prepared from Avicel by sulfuric acid hydrolysis. Our results are technologically relevant, as they contribute to the accessibility and sustainability of CNCs for a wide range of applications in various industries.

Potential Conversion of Coconut Husk-Waste to Magnetic Cellulose Designed for Synthetic Dye Removal

Increasing concern about sustainability and environmental issues caused by the massive amount of solid biomass waste in Indonesia has driven efforts to develop new products for various endues applications in energy, environment, and health sectors. This study uses coconut husk as the cellulose source to fabricate magnetic cellulose (MC) via coprecipitation with iron chloride salts. Combining cellulose with magnetite nanoparticles aims to improve the removal rate of synthetic dye as the latter provides high catalytic activity in the Fenton degradation process to eliminate persistent pollutants. The paramagnetic characteristics that MC possesses also make them quickly recovered after use. The adsorption capacity is found at 252.2 mg/g (pH 7, temperature of 30°C, the dye initial concentration of 100 ppm, and the precursor mass ratio of 1:4.8:25) for Rhodamine-B. The dye mineralization in this condition also reaches 50%, indicating that this adsorbent can be used as an efficient material to adsorb and degrade dye from an aqueous solution. This magnetic adsorbent will be of immense potential application for removing organic contaminants, particularly synthetic dyes, due to its good performance, simple separation, and ability to perform both adsorption and degradation processes simultaneously.

Waste newspaper as cellulose resource of activated carbon by sodium salts for methylene blue and congo red removal

The work was aimed at evaluating the adsorptive properties of waste newspaper (WN) activated carbons chemically produced using sodium salts for methylene blue (MB) and congo red (CR) removal. The activated carbons, designated as AC1, AC2, AC3 and AC4 were prepared through impregnation with NaH2PO4, Na2CO3, NaCl and NaOH, respectively and activation at 500 °C for 1 h. The activated carbons were characterized for surface chemistry, thermal stability, specific area, morphology and composition. The AC1 with a surface area of 917 m2/g exhibits a greater MB capacity of 651 mg/g. Meanwhile, a greater CR capacity was recorded by AC2 at 299 mg/g. The pseudo-second order model fitted well with the kinetic data, while the equilibrium data could be described by Langmuir model. The thermodynamic parameters, i.e.., positive ΔH°, negative ΔG° and positive ΔS° suggest that the adsorption of dyes is endothermic, spontaneous and feasible at high solution temperature. To conclude, WN is a potential cellulose source for producing activated carbon, while NaH2PO4 activation could be employed to convert WN into activated carbon for effective dye wastewater treatment.