Nanocellulose Research Articles

PLA based biodegradable bionanocomposite filaments reinforced with nanocellulose: development and analysis of properties

The 3D printing technique has recently become more prevalent among researchers for the fabrication of nanocomposites. The low crystallinity of polylactic acid (PLA) leads to the poor mechanical and thermal properties of its 3D-printed products, which restrict their applications in many fields. To overcome the limitations of PLA, the present work aims to develop PLA-based bionanocomposite filaments with varying percentages (1, 3, and 5 wt%) of crystalline nanocellulose (CNC) through a single screw extruder. The filaments will be further utilized for the development of bionanocomposite samples to evaluate their properties. The effect of CNC reinforcement on the chemical structure of the filaments was analyzed by FTIR analysis. XRD analysis revealed that the crystallinity of the filaments was significantly improved due to the nucleating effect of CNC. The maximum crystallinity was observed in the filament containing 1 wt% CNC, which was 26% higher than the pure PLA filament. The thermal and mechanical performance of the filaments was also considerably improved after CNC reinforcement, which was confirmed by DSC-TGA and tensile test analysis. The maximum tensile strength and tensile modulus were observed to be 48.9 MPa and 1700 MPa, respectively, in the filament reinforced with 1 wt% CNC, which was 35.5% and 21.89%, respectively, higher than those of the pure PLA filament. Rheological analysis showed that the complex viscosity, storage modulus, and loss modulus of the filaments were significantly affected by the reinforcement of CNC.

Rheology of nanocrystalline cellulose (CNC) gels: Thixotropy, yielding, wall slip, and shear banding

This study focuses on the rheological behavior of a cellulose nanocrystal gel. This system [5 wt. % cellulose nanocrystal (CNC) + 20 mM NaCl] is proved to be thixotropic, and the detected shear force tightly depends on the growth and break-up of the aggregates of CNC rods. From strain-controlled experiments, a nonmonotonic steady-state flow curve with a minimum stress value of ≈33 Pa is found, and the negative slope of stress versus shear rate suggests the existence of shear bands. From stress-controlled experiments (creep), the “static yield stress” is determined to be 67.5 ± 2.5 Pa. This difference proves that the local minimum stress of the flow curve does not coincide with the “static yield stress” determined by creep tests. However, this minimum stress can maintain flow provided that the material is already in a yielded state. At nominal shear rates below about 100 s−1, shearing is suggested to be localized in a shear band rather than over the whole material. The “dynamic yield stress” is found as “the minimum stress to maintain flow,” or the onset of shear banding. Moreover, wall slip also occurs at low nominal shear rates which is related to the interaction between the dynamic microstructure of the CNC gel and the wall: it is hypothesized that the low shear rates allow the CNC aggregates to extensively grow and, thus, the oversized CNC aggregates detach from the asperities of the wall. Our finding of the robust connection between yielding, thixotropy, wall slip, and shear banding shall shed new light on the nature of the nonmonotonic flow curves of yield stress and thixotropic materials.

The effect of urea-formaldehyde adhesive modification with diisocyanate-functionalized nanocellulose on the properties of particleboard

In this paper, a nanocrystalline cellulose (NCC) functionalized with 4,4′-diphenylmethane diisocyanate (MDI) was used as a modifier for urea-formaldehyde (UF) adhesive in particleboard production. The applied method of NCC functionalization with diisocyanate has not been previously studied in research on wood-based materials. Chemical structure of MDI-NCC evaluated with Fourier transform infrared spectroscopy (FTIR) demonstrated some significant changes indicating that the functionalization was effective. No change in crystallinity caused by the modification was noted based on the lateral order index and total crystallinity index. Hydrophilicity of NCC was reduced due to the functionalization with MDI. Based on the differential scanning calorimetry (DSC) results, it was found that the reactivity of the resin was improved by the addition of NCC, and moreover, the effect was even more noticeable when the MDI-NCC was introduced. Properties of manufactured particleboards such as density, water absorption and formaldehyde content were not affected by the resin reinforcement. In turn, the modification of NCC with MDI allowed to increase the strength and reduce swelling of the particleboards more significantly than in the case of a neat NCC. It indicates that application of diisocyanate-functionalized NCC has great potential for the use as the UF resin modifier in particleboard production.

STUDY THE ELECTRICAL PROPERTIES OF GRAPHENE OXIDE – NANOCELLULOSE COMPOSITE

This study investigates the electrical properties of a graphene oxide (GO) and nanocellulose (NC) composite using impedance spectroscopy, complemented by thorough characterization through Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and scanning electron microscopy (SEM). FTIR analysis revealed characteristic peaks corresponding to functional groups present in both GO and NC, providing insights into their chemical composition. XPS spectra exhibited distinctive peaks indicative of carbon and oxygen bonding states, elucidating the surface chemistry of the materials. Raman spectroscopy provided information on the structural order and defects within the samples, particularly highlighting the graphitic structure of GO. SEM images revealed the morphological features of the composite membrane, showcasing the distribution of NC particles and structural modifications induced by their incorporation. Impedance spectroscopy was utilized to investigate the electrical conductivity of the GO-NC composite. Results indicated a temperaturedependent behavior, with an increase in conductance observed as the temperature rose within the operational range of fuel cells. Remarkably, the addition of NC did not significantly alter the conductive behavior of the composite, suggesting compatibility and stability. In summary, this comprehensive characterization using multiple analytical techniques offers valuable insights into the electrical properties of the GO-NC composite. The findings suggest its potential for various applications requiring enhanced electrical conductivity, particularly in fuel cell technology.

Fabrication of CNC-AC bionanosorbents from the residual mass of Magnolia champaca l. Bark after methanol extraction for wastewater treatment: Continuous column adsorption study

In this current study, a new class of multifunctional biobased ecofriendly nanosorbents namely crystalline nanocellulose-activated char (CNC-AC) nanosorbents were fabricated by employing a much more innovative and beneficial solvent evaporation induced phase separation (EIPS) technique. While the crystalline nanocellulose (CNC) were extracted from a very much new, innovative, and beneficial agrowaste source namely banana tree (M. oranta) rachis fibers by conducting a series of chemical treatments like scouring, alkali treatment, bleaching, and acid hydrolysis reactions. Additionally, the biochar were synthesized from the residual mass of Magnolia champaca L. barks after methanol extraction and functionalized by 30 % H3PO4 to improve their overall properties. Besides these the fixed-bed continuous column adsorption study were carried out by optimizing the various influential factors such as preliminary concentration and flow rates of the inlet wastewater solution, along with the nanosorbent bed heights into the applied column. For better understanding the overall physicochemical, thermomechanical, and morphostructural behavior of the newly fabricated polyfunctional CNC-AC bionanosorbents the samples were characterized by conducting FTIR-ATR, FESEM, BET, XRD, TGA analysis. Meanwhile the treated and nontreated water specimens were examined by conducting AAS and UV–vis-NIR techniques. The obtained results recommended that the newly produced CNC-AC nanosorbents have contained a quite number of active edges/binding sites along with substantial sp. surface area (around 316.95 m2/g). Additionally, they possessed a crystallinity index about 59.98 ± 0.027 %, greater thermal steadiness up to 600 °C, and outstanding 2D honeycomb-like mesoporous peripheral surface microstructure with a promising spherical shapes and smaller size nearly 5–10 nm. The highest removal capacity were found at 538.91 mg/g and 455.70 mg/g for Pb2+ and CR respectively. Additionally, for better understanding the experimental breakthrough curves (BTC) were evaluated by several well established column models while the maximum R2 value was found around 0.999 for the Thomas model and reduced chi squire (χ2) value was around 0.0001.

BioMOF@cellulose Glycerogel Scaffold with Multifold Bioactivity: Perspective in Bone Tissue Repair.

The development of new biomaterials for musculoskeletal tissue repair is currently an important branch in biomedicine research. The approach presented here is centered around the development of a prototypic synthetic glycerogel scaffold for bone regeneration, which simultaneously features therapeutic activity. The main novelty of this work lies in the combination of an open meso and macroporous nanocrystalline cellulose (NCC)-based glycerogel with a fully biocompatible microporous bioMOF system (CaSyr-1) composed of calcium ions and syringic acid. The bioMOF framework is further impregnated with a third bioactive component, i.e., ibuprofen (ibu), to generate a multifold bioactive system. The integrated CaSyr-1(ibu) serves as a reservoir for bioactive compounds delivery, while the NCC scaffold is the proposed matrix for cell ingrowth, proliferation and differentiation. The measured drug delivery profiles, studied in a phosphate-buffered saline solution at 310 K, indicate that the bioactive components are released concurrently with bioMOF dissolution after ca. 30 min following a pseudo-first-order kinetic model. Furthermore, according to the semi-empirical Korsmeyer-Peppas kinetic model, this release is governed by a case-II mechanism, suggesting that the molecular transport is influenced by the relaxation of the NCC matrix. Preliminary in vitro results denote that the initial high concentration of glycerol in the NCC scaffold can be toxic in direct contact with human osteoblasts (HObs). However, when the excess of glycerol is diluted in the system (after the second day of the experiment), the direct and indirect assays confirm full biocompatibility and suitability for HOb proliferation.

The Correlations between Microstructures and Color Properties of Nanocrystalline Cellulose: A Concise Review.

Cellulose nanocrystals (CNCs) are a green resource which can produce photonic crystal films with structural colors in evaporation-induced self-assembly; CNC photonic crystal films present unique structural colors that cannot be matched by other colored materials. Recently, the mechanisms of CNC photonic crystal films with a unique liquid crystal structure were investigated to obtain homogenous, stable, and even flexible films at a large scale. To clarify the mechanism of colorful CNC photonic crystal films, we briefly summarize the recent advances from the correlations among the preparation methods, microstructures, and color properties. We first discuss the preparation process of CNCs, aiming to realize the green application of resources. Then, the behavior of CNCs in the formation of liquid crystal phases is studied, considering the influence of the CNCs' size and shape, surface properties, and the types and concentrations of solvents. Finally, the film formation process of CNCs and the control of structural colors during the film formation are summarized, as well as the mechanisms of CNC photonic crystal films with full color. In summary, considering the above factors, obtaining reliable commercial CNC photonic crystal films requires a comprehensive consideration of the subsequent preparation processes starting from the preparation of CNCs.

Preparations of Polyurethane Foam Composite (PUFC) Pads Containing Micro-/Nano-Crystalline Cellulose (MCC/NCC) toward the Chemical Mechanical Polishing Process.

Polyurethane foam (PUF) pads are widely used in semiconductor manufacturing, particularly for chemical mechanical polishing (CMP). This study prepares PUF composites with microcrystalline cellulose (MCC) and nanocrystalline cellulose (NCC) to improve CMP performance. MCC and NCC were characterized using scanning electron microscopy (SEM) and X-ray diffraction (XRD), showing average diameters of 129.7 ± 30.9 nm for MCC and 22.2 ± 6.7 nm for NCC, both with high crystallinity (ca. 89%). Prior to preparing composites, the study on the influence of the postbaked step on the PUF was monitored through Fourier-transform infrared spectroscopy (FTIR). After that, PUF was incorporated with MCC/NCC to afford two catalogs of polyurethane foam composites (i.e., PUFC-M and PUFC-N). These PUFCs were examined for their thermal and surface properties using a differential scanning calorimeter (DSC), thermogravimetric analysis (TGA), dynamic mechanical analyzer (DMA), and water contact angle (WCA) measurements. Tgs showed only slight changes but a notable increase in the 10% weight loss temperature (Td10%) for PUFCs, rising from 277 °C for PUF to about 298 °C for PUFCs. The value of Tan δ dropped by up to 11%, indicating improved elasticity. Afterward, tensile and abrasion tests were conducted, and we acquired significant enhancements in the abrasion performance (e.g., from 1.04 mm/h for the PUF to 0.76 mm/h for a PUFC-N) of the PUFCs. Eventually, we prepared high-performance PUFCs and demonstrated their capability toward the practical CMP process.

Multi-objective optimization of micro crystalline cellulose and montmorillonite filled poly lactic acid bio–composite and its characterizations

In this research study, the synthesis of poly lactic acid (PLA) based bio composite material factors contributions were investigated through the Taguchi-based grey relational analysis (GRA) technique. Effects of micro crystalline cellulose (MCC) and montmorillonite (MTT) nano clay filler, sorbitol (S) plasticizer, and temperature (T) operating factor on the PLA matrix through melt-mixing preparation method. The tensile strength (TS), Young modulus (YM), flexural strength (FS), flexural modulus (FM), hardness, impact strength (IS), water absorption (WA), and density properties of bio composite material were investigated for each experimental setup (orthogonal array, L16). Additionally, neat PLA and optimal sample structural, thermal, and morphological properties were examined through Fourier transform infrared spectroscopy (FTIR), X-Ray diffraction (X-RD), thermal gravimetry analysis/differential thermal gravimetry (TGA/DTG), and DSC and SEM analyses. The obtained result for optimal mechanical and physical properties of MCC/MTT/S/PLA bio composite was MCC at level 3 (6%), MTT at level 4 (9%), S at level 2 (10%), and T at level 4 (175 °C). Analysis of variance (ANOVA) shows that MTT has the greatest significant effect on mechanical and physical properties of MCC/MTT/S/PLA bio composite followed by MCC, T, and S. The confirmation test indicates that the improvement of weighted grey relational grade (GRG) from 0.7896 to 0.846 and the FTIR, XRD, thermal gravimetry/differential scanning calorimetry (TG/DSC), and scanning electron microscopy (SEM) results indicates that the good interaction between PLA and fillers, improvement of thermal and morphological properties of optimal (6MCC/9MTT/10S/175 °C) bio composite samples. Therefore, the multi-response characteristics of MCC/MTT/S/PLA bio composite can be highly improved by this technique.

Antimicrobial Effect of Waterborne Polyurethane-Based Cellulose Nanofibril/Silver Nanoparticles Composites and Acacia concinna (Willd.) DC Extract (Shikakai).

Antimicrobial coatings are becoming increasingly popular in functional material modification and are essential in addressing microbial infection challenges. In this study, the phytochemical and antimicrobial potential of aqueous, 80% methanol and 80% ethanol pod extracts of Acacia concinna (Willd.) DC (AC) and its application in the green in situ (one pot) synthesis of silver nanoparticles on Cellulose nano fibrils (CNF) and Waterborne polyurethane (WPU) were prepared. The phytochemical evaluation of Acacia concinna crude extracts showed the presence of alkaloids, flavonoids, phenols, tannins, terpenoids, saponins, steroids. The surface plasmon Resonance peak of CNF/AC-AgNPs was 450 nm and the FTIR result confirmed functional groups such as carbonyl, phenols and carboxyl were present which was important for the bio-reduction of silver nanoparticles. The crude AC aqueous pods extract against Gram-positive and Gram-negative bacteria compared with AC ethanol and AC methanol extracts. The WPU/CNF/AC-AgNPs composite dispersion was also good in terms of its antibacterial activities. The WPU/CNF/AC-AgNPs nanocomposites could be applied as bifunctional nanofillers as an antimicrobial agent in food packaging systems and other biological applications.

How Far Is the Nanocellulose Chip and Its Production in Reach? A Literature Survey.

The slowdown of Moore's Law necessitates an exploration of novel computing methodologies, new materials, and advantages in chip design. Thus, carbon-based materials have promise for more energy-efficient computing systems in the future. Moreover, sustainability emerges as a new concern for the semiconductor industry. The production and recycling processes associated with current chips present huge environmental challenges. Electronic waste is a major problem, and sustainable solutions in computing must be found. In this review, we examine an alternative chip design based on nanocellulose, which also features semiconductor properties and transistors. Our review highlights that nanocellulose (NC) is a versatile material and a high-potential composite, as it can be fabricated to gain suitable electronic and semiconducting properties. NC provides ideal support for ink-printed transistors and electronics, including green paper electronics. Here, we summarise various processing procedures for nanocellulose and describe the structure of exclusively nanocellulose-based transistors. Furthermore, we survey the recent scientific efforts in organic chip design and show how fully automated production of such a full NC chip could be achieved, including a Process Design Kit (PDK), expected variation models, and a standard cell library at the logic-gate level, where multiple transistors are connected to perform basic logic operations-for instance, the NOT-AND (NAND) gate. Taking all these attractive nanocellulose features into account, we envision how chips based on nanocellulose can be fabricated using Electronic Design Automation (EDA) tool chains.

Enhanced nanocellulose extraction from date palm waste: green solvent hydrolysis with transition metal complex

This study presents a novel method for nanocellulose production using [Bmim]Cl as a green solvent, with enhanced hydrolysis efficiency achieved through the addition of a transition metal complex as a catalyst. The redox capability of the transition metal complex to break the glycosidic bonds in cellulose is amplified by the addition of an oxidizing agent. This protocol represents the latest innovation in the field of nanocellulose production, resulting in improved yield and reduced particle size. Nanocellulose (NC) was extracted from date seeds using 1-butyl-3-methylimidazolium chloride [Bmim]Cl coupled with a transition metal complex comprising copper metal and pyridine as a ligand along with H2O2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${\ ext{H}}_{2}{\ ext{O}}_{2}$$\\end{document} as an oxidizing agent. Unlike conventional [Bmim]Cl hydrolysis, which typically yields only microcrystalline cellulose (MCC), this approach resulted in a 25% higher yield of NC than that of MCC. Dynamic light scattering analysis showed a substantial reduction in hydrodiameter from 1200 nm for MCC to 128.7 nm for NC, highlighting the remarkable efficiency of this process. Thermal analysis demonstrated the high stability of NC, which showed a Tonset\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${T}_{onset}$$\\end{document} of 286 °C and an activation energy (Ea\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${E}_{a}$$\\end{document}) of 220.41 kJ/mol. X-ray diffraction analysis indicated that NC possessed a high degree of crystallinity (Crl=\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${C}_{rl}=$$\\end{document} 70.28%). Furthermore, NC underwent modification with 3-aminopropyltriethoxysilane to replace free hydroxyl groups (–OH), making it redispersal and suitable for various applications. This modification was confirmed through Fourier transform infrared spectroscopy, which showed the presence of characteristic functional groups, and energy-dispersive X-ray spectroscopy, which verified the elemental composition. Zeta potential measurements revealed surface charge differences, with MCC at − 27.87 mV, NC at − 27.28 mV, and modified NC at − 44.72 mV, indicating improved colloidal stability after modification. These findings highlight the protocol's effectiveness and its potential impact on the NC production industry, offering improved yields and the production of nanosized fibers using green solvents.

An ionic liquid crystal functionalized nanocellulose lubricant additives

Cellulose, one of nature's most abundant, clean, and sustainable resources, has often shown unsatisfactory results when used as bio-lubricant additives. Herein, nanocellulose (NC) from amorphous waste natural poplar was extracted using deep eutectic solvent encapsulation treatment and chlorine bleaching process. Subsequently, 1-hexadecyl-3-methylimidazolium bromide was integrated onto NC using a one-step hydrothermal treatment (high-temperature and high-pressure environment) to obtain ionic liquid crystal (ILC) functionalized products (named as ILC-NC). After ball-milling process and solid phase separation step, ILC-NC exhibits excellent dispersion stability and lubrication properties in the liquid phase (including water and vegetable oil). Based on the polar and colloidal activity properties of ILC, it can form an ordered molecular layer on NC surface and form a lubricating film-like structure, making NC smoother and sliding well. Compared to ILC/NC aqueous dispersion, ILC-NC reduces the coefficient of friction and wear rate on steel disk surface by 68.75 % and 74.07 %, respectively. The minimum coefficient of friction was further reduced to 0.032 as dispersing ILC-NC in sunflower oil, showing a reduction of 0.134 (77.91 %) compared to pure sunflower oil. Finally, the lubrication theoretical model calculation reveals the lubrication state of ILC-NC on the steel disk surface and proposes the lubrication mechanism.

Defect passivation of organometal halide perovskite solar cells using low-cost green crystalline nanocellulose

Perovskite solar cells (PSCs) have made significant progress in recent years. However, the presence of defects in the photoactive absorption layer has become a limiting factor in the efficiency of PSCs. In this research, methylammonium lead iodide perovskite films with improved quality and reduced defect density were obtained with the addition of crystalline nanocellulose (CNC) biopolymer. CNC produced from biomass contains many hydroxyl groups that were able to passivate the defects in perovskite, increase grain size, and reduce recombination. The PSC made with CNC modification achieved an efficiency of 9.22 %, higher than similar PSC without the addition of CNC that produced an efficiency of 7.28 %. This work highlights the passivating impact of low-cost green cellulose for enhancing the electrical performance of PSC.

Controllable preparation and morphology regulation of nanocelluloses from waste paper by a green hydrolysis method

This study focused on the morphology regulation of nanocelluloses (NCs) aiming at preparing NCs with the controllable properties. NCs with rod-shaped, spherical, and rod-shaped and spherical composite structures were prepared from waste paper by a green enzymatic hydrolysis. The critical enzyme concentration for the transition of NCs from one morphology to another was explored. Several analytical methods, including TGA, XRD, SEM, TEM, DSC and WCA, were employed to characterize the prepared NCs. The results showed that with the cellulase enzyme concentration lower than 6 μ/ml or higher than 30 μ/ml, the prepared NCs had a single rod-shaped or spherical structure. When the cellulase concentration was between 6 and 30 μ/ml, the prepared NCs had a composite morphology of rods and spheres. Besides, NCs with a composite morphology dominated by rod-like or spherical structures had a higher thermal stability. Moreover, NCs prepared with cellulase enzyme concentration of 6 and 35 μ/ml had the highest and lowest crystallinity of 81.7 % and 59.3 %, respectively. Hence, this work achieved the morphology and property regulation of NCs by a green method which expanded the application scope of NCs and realized the high value utilization of waste paper.

The effect of nanocellulose and silica filler on the mechanical properties of natural fiber polymer matrix composites

Natural fiber-reinforced polymer matrix composites recently got great attention in biomedical applications due to their inherent characteristics such as biocompatibility, lightweight, and biodegradability. However, natural fiber composites suffer from poor mechanical properties and weak interfacial adhesion. It is well documented that the addition of nanofiller has improved the mechanical properties of different synthetic fibers such as glass and carbon composites. The main objective of this paper is to study nanofillers' effect on the mechanical properties of unidirectional false banana fibers reinforced polymer composites. The filler materials, crystalline nanocellulose fibrils, and crystalline nanosilica particles were extracted from sugarcane bagasse and its byproducts. The composite samples were fabricated by adding the nanofillers in unidirectional natural fibers arranged in four fiber orientations (0°, 0o/90o ±45o, and quasi-isotropic), and their tensile, flexural, compression strength, thermal stability, and void content were measured following ASTM standards. The results revealed that adding nanofillers increased the tensile, flexural, and compressive strengths by 16 % (98.83 Mpa), 11 % (161.60 Mpa), and 23 % (114.62 Mpa), respectively. Similarly, at 0° orientation, the addition of nanoparticles enhances the tensile, bending, and compressive modulus by 30 % (15.43 Gpa), 12 % (13.52 Gpa), and 60 % (42.6 Gpa), respectively. On the other hand, the void content was reduced with the addition of nanofillers. The results also revealed that composites with crystalline nanosilica particle fillers had superior thermal stability compared to crystalline nanocellulose fibril fillers. The overall results of this research give the confidence that nano particle-filled natural fiber composites can be used for bio-based engineering applications, such as prosthetic sockets.

Assessing the ecotoxicological effects of novel cellulose nanocrystalline glitter compared to conventional polyethylene terephthalate glitter: Toxicity to springtails (Folsomia candida)

Glitter is a type of microplastic, and thus there is a need to assess its potential impacts on the environment and to assess the potential for non-plastic cellulose nanocrystal structurally colored glitters as safe and sustainable replacements. The ecotoxicity of glitter has been mostly ignored in the research literature, with only a few published studies focusing on aquatic organisms. Therefore, an exposure experiment was conducted to examine the impact of conventional polyethylene terephthalate (PET) glitter as well as untreated and heat-treated cellulose nanocrystal (CNC) based glitter on the survival, reproduction, and length of Folsomia candida (springtail). Folsomia candida reproduction was reduced by 61% (P = 0.013) after exposure to PET glitter at 1000 mg/kg, while no significant effects were observed on F. candida survival and length. In contrast, there were no significant impacts on F. candida survival, length, or reproduction when exposed to untreated or heat-treated CNC glitter. These results indicate that exposure to PET glitter may impact soil invertebrates at the population level, and that CNC glitter has potential as a biodegradable non-plastic alternative to PET glitter to decrease detrimental effects on soil ecosystems.

A new approach to detect the imbalance of hemoglobin and methemoglobin levels in human plasma based on a fluorescent modified nanocellulose chemosensor

This work has developed a new, rapid, highly sensitive, and precise approach to identify the imbalance levels of hemoglobin and methemoglobin through fluorescence emission spectroscopy. A study on a new Schiff base-modified nanocellulose (PY-PDA-DANC) applied as a fluorescent chemosensor is reported. To prepare the chemosensor, nanocellulose (NC) was first converted into 2,3-dialdehyde nanocellulose (DANC), and then modified by grafting o-phenylenediamine (PDA), followed by 1-pyrenecarboxaldehyde giving rise to the new blue-fluorescent complex PY-PDA-DANC. All the synthesized products were characterized using FTIR, 1H NMR, XRD, EDX and UV–vis spectroscopy. The fluorescence response of PY-PDA-DANC against various metal ions (Co2+, Cr3+, Cu2+, Fe2+, Fe3+, Hg2+, K+, Mg2+, Mn2+, Na+, Ni2+, Pb2+ and Zn2+) in DMSO/H2O media was evaluated using PL spectroscopy. The fluorescent sensor showed high and selective quenching response to both Fe2+ and Fe3+ ions with low limit of detection (LOD). PY-PDA-DANC was also successfully applied for sensing of heme–iron coordinated to hemoglobin (HB) and methemoglobin (MHB), displaying a LOD of 28.45 nM and 65.36 nM, respectively. Subsequently, it was applied for the analysis of [Fe2+@HB] and [Fe3+@MHB] in human plasma sample with good recoveries.

Synthesis of bio-polyol-functionalized nanocrystalline celluloses as reactive/reinforcing components in bio-based polyurethane foams by homogeneous environment modification

Nanocrystalline Cellulose (NCC or CNC) is widely used as a filler in polymer composites due to its high specific strength, tensile modulus, aspect ratio, and sustainability.However, CNC hydrophilicity complicates its dispersion in hydrophobic polymeric matrices giving rise to aggregate structures and thus compromising its reinforcing action. CNC functionalization in a homogeneous environment, through silanization with trichloro(butyl)silane as a coupling agent and subsequent grafting with bio-based polyols, is herein investigated aiming to enhance CNC dispersibility improving the filler-matrix interaction between the hydrophobic PU and hydrophilic CNC. The modified CNCs (m_Ci) have been studied by XRD, SEM, and TGA analyses. The TGA results show that the amount of grafted polyol is strongly influenced by both its molar mass and OH number and the maximum amount of grafted polyol reaches up to 0.32 mmol per grams of functionalized CNC, within the explored conditions. The effect of different concentrations (1–3 wt%) of m_Ci on the physical, morphological, and mechanical properties of the resulting bio-based composite polyurethane foams is evaluated. Composite PU foams present compressive modulus up to 4.81 MPa and strength up to 255 kPa more than five times higher than those reinforced with unmodified CNC or with modified CNC in heterogeneous chemical environment. The improvement of mechanical properties of the examined PU foams, as a consequence of the incorporation of bio-polyols modified CNCs where polyol's OH groups interact with polyurethane precursors, could further broaden the use of these materials in building applications.

Two-Emission Channel Hybrid Nanosensors Based on BODIPY-Appended Nanocrystalline Cellulose for Determination of Biothiols

Two-Emission Channel Hybrid Nanosensors Based on BODIPY-Appended Nanocrystalline Cellulose for Determination of Biothiols