Crystal Detector Research Articles

Characterization of Plasma-etched Surfaces of TlBr Crystals for Radiation Detectors

Characterization of Plasma-etched Surfaces of TlBr Crystals for Radiation Detectors

Study of electric-field induced ionic migration on all-inorganic perovskite CsPbBr3 single crystal nuclear radiation detector

As one of the promising room temperature nuclear radiation detection materials, the all-inorganic perovskite CsPbBr3 single crystal has been receiving much attention in recent years. Even though the performance of the CsPbBr3 detector is improving continuously, the disadvantages of detection instability have not been solved fundamentally, and this instability is mainly caused by ionic migration in the CsPbBr3 single crystal itself. In this paper, a reasonable ionic migration model is proposed based on an in-depth study of the current hysteresis phenomenon and ionic migration mechanism in the Ti/CsPbBr3/Ti detector. The model shows that the ions migrate to the anode or cathode under an external electric field, and the accumulated ions subsequently form an inverted internal electric field inside the crystal and carrier transport barriers at the metal–semiconductor interface simultaneously. The photoelectric characteristic and ionic migration activation energy (Eaion) fitting results also prove the rationality of the ionic migration model. Furthermore, the ionic migration model can also be used to explain the left-shift of the energy response peak and the decrease in the normalized charge collection efficiency in the Ti/CsPbBr3/Ti detector. This paper systematically investigates the intrinsic origin of migrated ions and the influence of ionic migration on detection stability, which will provide a potential solution to improve detection stability by suppressing ionic migration in the near future.

Confirming X-ray parametric down conversion by time–energy correlation

We present measurements of X-ray Parametric Down Conversion at the Advanced Photon Source synchrotron facility. Using an incoming pump beam at 22 keV, we observe the simultaneous, elastic emission of down-converted photon pairs generated in a diamond crystal. The pairs are detected using high count rate silicon drift detectors with low noise. Production by down-conversion is confirmed by measuring time–energy correlations in the detector signal, where photon pairs within an energy window ranging from 10 to 12 keV are only observed at short time differences. By systematically varying the crystal misalignment and detector positions, we obtain results that are consistent with the constant total of the down-converted signal. Our maximum rate of observed pairs was 130/h, corresponding to a conversion efficiency for the down-conversion process of 5.3±0.5×10−13.

Direct detection of minimum ionizing charged particles in a perovskite single crystal detector with single particle sensitivity.

We report the detection of high energy electrons of some hundreds of MeV, crossing a methylammonium lead bromide single crystal device with sensitivity down to a single electron. In the device, the released energy is close to the energy released by minimum-ionizing particles. This is the first demonstration of a perovskite-based device that can be used for tracking and counting minimum-ionizing charged particles. The device reaches single particle sensitivity with a low bias voltage of 5 V. It also shows a good linearity of the response as a function of the number of electrons in a dynamic range of approximately 104.

Experimental validation of Monte Carlo NaI(Tl) detector efficiency responses with surrogate 137Cs environmental contamination source term

Radiological site remediation is a resource intensive process requiring extensive field sampling to demonstrate regulatory compliance. Specifically, the application of Monte Carlo (MC) simulations and automated hybrid radiation transport methods has garnered interest in streamlining the remediation process by simulating detector responses for a plurality of contaminated media, contamination depths and profiles, and source-detector orientations. In this study, experimental validation of gamma-ray detector efficiency responses was conducted for simulations of radiological site-specific and idealized external contamination conditions. Measurements were performed with a cylindrical 2′′ × 2″ sodium iodide thallium-doped (NaI(Tl)) scintillator detector suspended above a 217.8 kBq, 50 cm × 50 cm 137Cs contamination source located on the surface of or buried within environmental soil. New area correction factors (ACFs) and gamma shielding factors (GSFs) were also derived to modify the simulated idealized detector efficiency responses, accounting for reductions in source area and clean soil covering layers, respectively, that may be encountered when performing in-situ gamma spectrometry in the field. The study concluded that simulated total detection efficiency from energy deposition in the active volume of the detector crystal can be adopted for radionuclide screening purposes. Furthermore, pragmatic implementation of environmental surveying using gamma-spectrometry requires site-specific information.

Investigation of polarization mechanism in MSM TlBr crystal room-temperature nuclear radiation detector

Thallium Bromide (TlBr) single crystal detector is widely recognized as an excellent semiconductor nuclear radiation detector. And its detection performance has already reached commercial level of the majority semiconductor detector. However, the long-term stability of TlBr detector always exhibited a serious polarization effect and the commercial application of TlBr detector is heavily limited. In this paper, the polarization phenomenon, polarization mechanism and the influence of polarization effect on detection performance are systematic investigated. As the metal-semiconductor interface plays an important role in detector performance, two typical metal-semiconductor-metal structure, Au/TlBr/Au and Ti/TlBr/Ti detectors are designed and fabricated in this paper. The XPS in-situ analysis results reveal that different oxidation/reduction reactions would happen at the metal-semiconductor interface of Au/TlBr/Au and Ti/TlBr/Ti detectors. The serious polarization effect in Au/TlBr/Au detectors resulted from the aggregated [AuBr4]- ion at the Au/TlBr interface. Meanwhile, the relative weaken polarization effect in Ti/TlBr/Ti detectors is ascribed to the combined effects of oxidic titanium ions (Ti3+, Ti4+) and metallic Ti–Tl layer at the Ti/TlBr interface. Thus, the detector Ti/TlBr/Ti has a relative better energy resolution and long-term stability compared to detector Au/TlBr/Au. This paper systematic investigate the polarization mechanism and the influence of polarization effects on TlBr detector performance, and this will provide a potential solution to suppress the polarization problem by electrode architecture designing in the near future.

Comparative Study of Cat’s Whiskers Leaves (Orthosiphon stamineus) and Mint Leaves (Mentha arvensis) as Repellent For Houseflies

House flies (Musca domestica) are one of the challenging pests that are difficult to overcome and control. Common control methods usually involve the use of chemical insecticides, but a more environmentally friendly alternative is to use plant-based insecticides with repellent properties. Medicinal plants from the Lamiaceae family are famous for their distinctive aroma and are effective in treating pest problems. This research aims to evaluate the potential of cat's whisker leaves and mint leaves as housefly repellent. The repellency test used cotton impregnated with extract concentrations of 2,000 ppm, 4,000 ppm, 6,000 ppm, 8,000 ppm and 10,000 ppm. Exposure time was 30 minutes and carried out 3 times. The repellency percentage is then calculated. The results of the research showed that at concentrations of 2,000 ppm and 4,000 ppm there were still some flies landing, but at concentrations of 6,000 ppm, 8,000 ppm and 10,000 ppm no flies landed. Strong repulsion was observed at concentrations of 2,000 ppm (86.7% for cat's whisker leaf extract and 82.7% for mint leaf extract) and 4,000 ppm (96% for cat's whisker leaf extract and 88% for mint leaf extract). Both extracts showed very strong repulsion (100%) at concentrations of 6,000, 8,000 and 10,000 ppm. These results show that the higher the concentration, the stronger the repellent effect produced. In conclusion, cat's whiskers and mint leaves have potential as active mosquito repellent ingredients, and this research can be the basis for further development as a pest control method, especially against houseflies.

Surface-barrier detector with smoothly tunable thickness of depleted layer for study of ionization loss and dechanneling length of negatively charged particles channeling in a crystal

A new method for the experimental study of ionization loss of relativistic negatively charged particles moving in a crystal in the channeling regime using a semiconductor surface-barrier detector with smoothly tunable thickness of the depleted layer is proposed. The thickness of the depleted layer in a flat semiconductor detector can be smoothly regulated by the value of the bias voltage applied to the detector. Therefore, the energy distribution of the ionization loss of relativistic particles which cross the detector and move in the channeling regime in the detector crystal can be measured along the path of the particles by varying the bias voltage of the detector and the dechanneling length can be found. Available literature data on experimental and theoretical researches of the dechanneling length are reviewed. The significant disagreement between the experimental and theoretical data is noted. Comparison of experimental data obtained by the detector-target with smoothly tunable thickness of the depleted layer with calculations can help to develop theoretical description of the dynamics of motion of negatively charged particles channeling in a crystal. A better understanding of the dechanneling length properties can be useful in the production of positrons and other particles such as neutrons by an electron beam in crystals, as well as in the development of crystalline undulators, and in the crystal-based extraction of electron beams from a synchrotron.

Cherenkov-type terahertz generation by optical rectification in KD2PO4 (DKDP) crystal

The potential of KD2PO4 (or DKDP) crystal as a terahertz generator is demonstrated, despite its extremely strong terahertz absorption. By combining the Cherenkov radiation scheme and surface-emitting geometry, femtosecond Ti:sapphire laser pulses of ∼200−300 μJ energy were converted to broadband (∼4 THz bandwidth) terahertz transients with the efficiency of ∼8×10−6. The transients produced electro-optic signals of a ∼0.15 modulation depth and ∼103 dynamic range in a 1-mm thick ZnTe detector crystal. This suggests DKDP as a potential generator crystal for terahertz time-domain spectroscopy. From our measurements, we estimated the nonlinear coefficient d36≈3 pm/V of DKDP for optical rectification, which is an order of magnitude larger than the value known from second-harmonic-generation experiments. At the same time, the obtained value of d36 is an order of magnitude smaller than the value calculated from the clamped electro-optic coefficient r63 for the MHz frequency range. At high pump intensities, we observed multiple filamentation of the pump beam and white light generation, spatially separated from terahertz generation.

Integration of Large-Area Halide Perovskite Single Crystals and Substrates via Chemical Welding Using an Ionic Liquid for Applications in X-ray Detection.

The large carrier lifetime mobility product and strong stopping power for high-energy X-rays make halide perovskites an attractive candidate for next-generation X-ray detectors. In particular, high-energy X-rays in the range of several tens of keV require halide perovskite absorber layers with thicknesses exceeding a few millimeters. To avoid carrier scattering caused by grain boundaries at such thicknesses, the utilization of single crystals is desirable. Large-area single crystals are predominantly grown in a freestanding form, and integration onto a substrate is necessary for the fabrication of commercial devices. However, an effective method for integrating large single crystals onto a substrate has not yet been developed. In this study, a large-area (20 cm2) MAPbBr3 single crystal is bonded to an indium tin oxide (ITO) substrate using an ionic liquid, showing strong adhesion strength of 164 kPa. X-ray detectors based on ITO/MAPbBr3 single crystal bonded by methylammonium acetate achieved excellent sensitivity of 91,200 μC Gyair-1 cm-2, the highest among substrate-integrated halide perovskite single crystal X-ray detectors.

Estimation of transfer factor from soil to cassava in Ethiope East, Delta State, Nigeria

Cassava is a very important staple food crop in Delta state. The aim of this research is to assess the activity concentration level and determine the transfer factor of radionuclide from soil to cassava in Ethiope Local Government Area of Delta state, Nigeria. The activity concentration of 40K, 238U and 232Th in soil and cassava samples collected from the study area were analysed using gamma spectrometry. A lead-shielded 3 x 3 inch coaxial type Sodium Iodide Thallium [NaI(TI)] doped detector crystal (Model No. 802 series, Canberra Inc.) coupled to a Canberra series multichannel Analyzer (MCA) (Model N0.1104) through a preamplifier was used. The results of the activity concentration in soil samples indicate that, 40K has the highest mean activity concentration ((38.66 ± 3.69) BqKg−1) with the highest value ((62.47 ± 5.67) BqKg−1) recorded at E2. The mean activity concentrations of 238U and 232Th are 3.65 ± 0.90 BqKg−1 and 0.46 ± 0.05 BqKg−1respectively. The peak values of 238U and 232Th are 5.07 ± 1.17 BqKg−1 and 0.98 ± 0.11 BqKg−1. From cassava, 40K varies from 75.06 to 200.08 BqKg−1 with the highest mean activity concentration of 99.62 ± 8.32 BqKg−1 and 200.08 ± 14.90 BqKg−1 as the highest value noted at C5. The mean activity concentrations of 238U and 232Th are 3.89 ± 0.93 BqKg−1 and 0.81 ± 0.09 BqKg−1 respectively. The maximum values of 238U and 232Th determined from the computation from cassava samples are 11.10 ± 2.48 BqKg−1 and 1.70 ± 0.18 BqKg−1. The results of this study show that the activity concentration of 40K, 238U and 232Th in the study area are lower than world average values of 420, 30 and 35 BqKg-1 in soil and cassava respectively, and it is therefore not harmful if consumed. The mean transfer factor of 40K, 238U and 232Th from soil to cassava are 3.12 ± 0.44, 0.95 ± 0.31 and 2.96 ± 0.91 respectively. The range of values of 40K, 238U and 232Th varied as 1.41 to 5.82, BDL to 2.98 and 0.21 to 9.35 correspondingly. Peak values of the TF were noted as 5.82 for 40K at E8, C8, 2.98 for 238U at at E9, C9 and 9.35 for 232Th at E9, C9. The high value of TR is accredited to the richness of the organic matter in the soil. The quick recycling of natural radionuclides through the soil-cassava suggests the presence of an internal cycling that help the build-up of the natural radionuclides.

The single crystal diamond-based diagnostic suite of the JET tokamak for 14 MeV neutron counting and spectroscopy measurements in DT plasmas

The Joint European Torus (JET) has recently conducted its second deuterium–tritium (DT) experimental campaign DTE2, providing unique opportunity for studying both physics and engineering aspects of nuclear fusion plasmas. This also allowed the exploitation of new diagnostics and technologies that were not available during the first JET DT campaign held in 1997. Among these new instruments, the enhancement projects of the JET nuclear diagnostics lead to the development and installation of synthetic single crystal diamond detectors along different collimated line of sights. This paper describes the single crystal diamond-based diagnostic suite of the JET tokamak and the enhanced 14 MeV neutron diagnostic capabilities in terms of neutron yield and high resolution neutron spectroscopy. The diamond characterization measurements and the calibration procedure at JET are shown, together with performance of the diamond based neutron spectrometer as 14 MeV neutron yield monitor which allows the separation of 2.5 MeV and 14 MeV neutrons in trace tritium plasmas. The first high-resolution 14 MeV neutron spectroscopy measurements in neutral beam injection-heated DT plasmas are presented, allowing thermal and non-thermal neutron component separation. Prospects for the diagnose of DT burning plasmas such as ITER and SPARC will be presented.

Search for Boosted Dark Matter in COSINE-100.

We search for energetic electron recoil signals induced by boosted dark matter (BDM) from the galactic center using the COSINE-100 array of NaI(Tl) crystal detectors at the Yangyang Underground Laboratory. The signal would be an excess of events with energies above 4MeV over the well-understood background. Because no excess of events are observed in a 97.7 kg·yr exposure, we set limits on BDM interactions under a variety of hypotheses. Notably, we explored the dark photon parameter space, leading to competitive limits compared to direct dark photon search experiments, particularly for dark photon masses below 4MeV and considering the invisible decay mode. Furthermore, by comparing our results with a previous BDM search conducted by the Super-Kamionkande experiment, we found that the COSINE-100 detector has advantages in searching for low-mass dark matter. This analysis demonstrates the potential of the COSINE-100 detector to search for MeV electron recoil signals produced by the dark sector particle interactions.

High temperature X-ray and γ-ray spectroscopy with a diamond detector

A single crystal chemical vapour deposition diamond detector was electrically characterised and then investigated as a spectroscopic photon counting X-ray and γ-ray detector across the temperature range, T, −20 °C ≤ T ≤ 100 °C. The detector was connected to a custom-built charge-sensitive preamplifier of low electronic noise and illuminated in turn by 55Fe radioisotope X-ray and 109Cd radioisotope X-ray and γ-ray sources. In combination, the radiation sources provided characteristic soft (e.g. 5.9 keV) and hard (e.g. 22.16 keV) X-rays and 88.03 keV γ-ray emissions. The Mn Kα (5.9 keV) and Kβ (6.49 keV) X-ray emissions from the 55Fe radioisotope X-ray source were detected (and separated from the zero energy noise peak) at temperatures of −20 °C ≤ T ≤ 60 °C; the Ag Kα (22.16 and 21.99 keV) and Kβ (24.94, 24.99, and 25.46 keV) X-ray emissions and 88.03 keV γ-ray emissions were detectable across the entire temperature range investigated (−20 °C ≤ T ≤ 100 °C). The detector and the preamplifier were operated without cooling across the entire temperature range. The energy resolution (full width at half maximum) at 22.16 keV (Ag Kα1) was 4.57 keV ± 0.26 keV at 100 °C and 2.70 keV ± 0.18 keV at −20 °C. Noise analysis indicated that the combination of dielectric noise and any incomplete charge collection noise present dominated the other noise components at 5.9 keV. When the detector was illuminated with the 109Cd radioisotope X-ray and γ-ray source, a high count rate introduced parasitic effects (possibly baseline shift) which reduced the optimum shaping time of the spectrometer.

INTERACTIONS OF ORTHOSIPHON STAMINEUS COMPOUNDS AGAINST COX-2 AS AN ANTI-INFLAMMATORY USING IN SILICO METHODS AND TOXICITY PREDICTION

Objective: Orthosiphon stamineus, or cat's whiskers, are known to have several pharmacological activities, one of which is anti-inflammatory. An in silico study was conducted to determine the active compound with anti-inflammatory activity from Orthosiphon stamineus leaves while also assessing their toxicity. Methods: AutoDock 4 was used to perform molecular docking, while LigandScout 4.4.3 Advanced was used to screen pharmacophores. The Swiss ADME and PreAdmet websites were used to screen the prediction of Lipinski’s rules of 5 and toxicity. Results: In this in silico study on the COX-2 enzyme (PDB ID: 3ln1) with a RMSD validation value of 1.00 Å, Tetramethyl Luteolin emerged as the most promising candidate, exhibiting the lowest binding energy of-9.90 kcal/mol and a KI value of 55.80 nM, indicating favorable interactions within the active site. The compound also satisfied the Lipinski Rules and demonstrated favorable absorption and distribution characteristics, with HIA at 98.440681% and CaCO2 permeability at 53.1689 nm/sec, along with a small BBB value of 0.0154021 and quite good %PPB of 87.388706. Furthermore, Tetramethyl Luteolin obtained a pharmacophore fit score of 32.42, indicating possession of key structural features essential for desired biological activity. Conclusion: The flavonoid-derived compounds in cat's whisker leaf extract show promise as potential anti-inflammatory drug candidates, with Tetramethyl luteolin emerging as the best candidate among nine compounds, meeting Lipinski rules and exhibiting superior ADMET properties. These results highlight the potential of Tetramethyl Luteolin as a lead compound, necessitating additional research into its intended target or biological function.

Influence of high fluence heavy ion irradiation on the performance of single crystal diamond detectors

Radiation detectors based on diamond are highly favored for particle physics research due to their superior radiation hardness. In this work, the performance of single crystal diamond detectors under high fluence heavy ion radiation has been investigated. After irradiation by Fe13+ and Xe20+ ion beams with a high particle fluence of 1.2 × 1015 cm-2, the properties of unirradiated and irradiated intrinsic single crystal chemical vapor deposition (CVD) diamond detectors are compared by means of the spectroscopic energy resolution, charge collection efficiency (CCE), mobility-lifetime (μτ) product and time response using a 241Am alpha (α) particle source. The experimental results of the unirradiated sample with respect to I-V dark current levels, showed an ohmic behaviour of the Al and Cr/Au contact, CCE of 100%, fast response with a rise time of 750 ps and a fall time of 600 ps as well as drift velocities of 6.67 × 104 m/s and 4.72 × 104 m/s for holes and electrons respectively. In the case of the irradiated samples, the CCE, μτ product and time response pulse amplitude of holes and electrons were all degraded, indicating that high density trappings for both kinds of carriers were created under the diamond crystal surface and the trapping probability of holes and electrons was equal, which was different from the previous reports in the literature where only higher trapping probability of holes were observed under heavy ions irradiation. In particular, the spectroscopic performance as well as μτ product of holes and electrons in Fe13+ irradiated sample decreased more than those in Xe20+ irradiated sample, which implied that the recombination of electrons and holes increased in Fe13+ irradiated sample with greater penetration depth than that in Xe20+ irradiated sample when radiation fluence was up to 1015 cm-2, despite the lower density of lattice vacancies in Fe13+ irradiated sample. Moreover, the rise time of holes was slightly different, but the drift velocity was basically the same as that of the unirradiated sample, and so was that of the electrons. Anyway, the presented results showed that the diamond detectors irradiated by heavy ions at a high fluence of 1015 cm-2 still retained their good spectroscopic and very fast time response properties.

Helicity dependent cross sections for the photoproduction of π0π± pairs from quasi-free nucleons

Photoproduction of π0π±-pairs from quasifree nucleons bound in the deuteron has been investigated to study the helicity dependence of this reaction. Measurements with a liquid deuterium target were used to extract the unpolarized cross sections for reactions on protons and neutrons. A deuterated, longitudinally polarized solid-butanol target, together with a circularly polarized photon beam, determined the double polarization observable E. From these results the spin-dependent cross sections σ1/2 and σ3/2, corresponding to the anti-parallel and parallel spin configurations of the beam photon and target nucleon, have been derived. The measurements were performed at the Mainz MAMI accelerator with tagged, circularly-polarized photon beams produced via bremsstrahlung from longitudinally polarized electron beams. The reaction products were detected with an almost 4π solid-angle covering calorimeter composed of the Crystal Ball and TAPS detectors, supplemented by plastic scintillation detectors for charged particle identification. The results are sensitive to sequential decays of nucleon resonances via intermediate states and also to the decay of nucleon resonances by emission of charged ρ mesons, and are compared to recent model results.

Rheological engineering of perovskite suspension toward high-resolution X-ray flat-panel detector

Solution-processed polycrystalline perovskite film is promising for the next generation X-ray imaging. However, the spatial resolution of current perovskite X-ray panel detectors is far lower than the theoretical limit. Herein we find that the pixel level non-uniformity, also known as fixed pattern noise, is the chief culprit affecting the signal-to-noise ratio and reducing the resolution of perovskite detectors. We report a synergistic strategy of rheological engineering the perovskite suspensions to achieve X-ray flat panel detectors with pixel-level high uniformity and near-to-limit spatial resolution. Our approach includes the addition of methylammonium iodide and polyacrylonitrile to the perovskite suspension, to synergistically enhance the flowability and particle stability of the oversaturated solution. The obtained suspension perfectly suits for the blade-coating process, avoiding the uneven distribution of solutes and particles within perovskite films. The assembled perovskite panel detector exhibits greatly improved fixed pattern noise value (1.39%), high sensitivity (2.24 × 104 μC Gyair−1 cm−2), low detection limit (28.57 nGyair·s−1) as well as good working stability, close to the performance of single crystal detectors. Moreover, the detector achieves a near-to-limit resolution of 0.51 lp/pix.

Ethnoeconomics of Plants as Traditional Medicine (Ethnomedicine) and Food (Ethnoculinary) of the Bastem Indigenous Community in Luwu Regency

Ethnoeconomics is the study of the economic value or use of biological resources by an ethnic group and becomes wisdom. The aim of the research is to inventory the types of plants used as traditional medicine and food by the Bastem indigenous people. The methods used in the research were observation, interviews, focus group discussions (FGD), and literature study, while the sample collection technique used purpose sampling. This type of exploratory research uses a PRR (Participatory Rural Appraisal) approach. The sample criteria used were community leaders and traditional healers. The research data, which is respondents' emic data, is presented in tabular form, then analyzed descriptively and compared with scientific data based on Google Scholar, Sinta, and Research Gate sources. The results of the research show that the types of plants with the economic value used by the Bastem indigenous people as traditional medicine (ethnomedicine) are bangle, galangal, aromatic ginger, white turmeric, coffee leaves, avocado leaves, castor leaves, banana shoots, cat's whiskers, bitter gourd, guava leaves, papaya leaves, lemongrass and ciplukan, while the plants used as food by indigenous communities (ethnoculinary) are grouped into staple foods, vegetables and side dishes, traditional cakes and my day's food. Staple foods include sokko, limestone, corn porridge, sweet potato rice, banana rice and banana sokko. Vegetables and side dishes include green vegetables, burak, and nasu kadundung. Traditional cakes include putu pesse, tori cake, and baruasa. My daily food includes baurasa, gogos, and tumbu'.

Comparative Study of Single Crystal and Polymeric Pyroelectric Detectors in the 0.9-2.0 THz Range Using Monochromatic Laser Radiation of the NovoFEL.

The development of efficient and reliable sensors operating at room temperature is essential to advance the application of terahertz (THz) science and technology. Pyroelectric THz detectors are among the best candidates, taking into account their variety, outstanding performance, ease of fabrication, and robustness. In this work, we compare the performance of six different detectors, based on either LaTiO3 crystal or different polymeric films, using monochromatic radiation of the Novosibirsk Free Electron Laser facility (NovoFEL) in the frequency range of 0.9-2.0 THz. The main characteristics, including noise equivalent power and frequency response, were determined for all of them. Possible reasons for the differences in the obtained characteristics are discussed on the basis of the main physicochemical characteristics and optical properties of the sensitive area. At least three detectors showed sufficient sensitivity to monitor the shape and duration of the THz macropulses utilizing only a small fraction of the THz radiation from the primary beam. This capability is crucial for accurate characterization of THz radiation during the main experiment at various specialized endstations at synchrotrons and free electron lasers. As an example of such characterization, the typical stability of the average NovoFEL radiation power at the beamline of the electron paramagnetic resonance endstation was investigated.