Cathode Material For Sodium-ion Batteries Research Articles

Interfacial Engineering of P2-Type Ni/Mn-Based Layered Oxides by a Facile Water-Washing Method for Superior Sodium-Ion Batteries.

Owing to the strong basicity and reactivity, residual sodium compounds (RSCs) on the surface of Na-based layered oxides for sodium-ion batteries (SIBs) cause the deterioration of the electrochemical performance and processability of the oxide cathode materials. Herein, considering P2-type Na0.66Ni0.26Zn0.07Mn0.67O2 as the model material, the water-washing treatment is proven to be a facile, economic, and highly efficient method to improve the electrochemical performance of P2-type Ni/Mn-based layered oxides. Experimental results show that RSCs on material surfaces can be effectively removed by water washing without causing severe damage to the bulk structure. Notably, water washing triggers the formation of an ultrathin (2-3 nm thick) Na-poor disordered interfacial layer on the surface of Na0.66Ni0.26Zn0.07Mn0.67O2. This layer plays a passivating role in further enhancing the material's resistance to water and reduces the reactivity of the material surface with the electrolyte. These compositional and structural optimizations for P2-type Na0.66Ni0.26Zn0.07Mn0.67O2 effectively suppress the release of gaseous CO2, formation of thick cathode-electrolyte interphase films, and consumption of active Na+, enabling good Na+ transport kinetics during cycling. The water-washed Na0.66Ni0.26Zn0.07Mn0.67O2 exhibits significantly improved cycling stability with a capacity retention of 89.1% at 100 mA g-1 after 100 cycles and rate capability with a discharge capacity of 76.3 mA g-1 at 2000 mA g-1; these values are higher than those of the unwashed Na0.66Ni0.26Zn0.07Mn0.67O2 (83.3%, 71.4 mA h g-1). This work provides fundamental insights into the detrimental effect of RSCs on the electrochemical performance of layered oxides and highlights the importance of regulating interfacial compositions for developing high-performance layered-oxide cathode materials for SIBs.

Solid-state synthesis of low-cost and high-energy-density sodium layered-tunnel oxide cathodes: Dynamic structural evolution, Na+/vacancy disordering, and prominent moisture stability

Manganese-based layered oxides show promise as cathode materials for sodium-ion batteries (SIBs). However, several challenges including sluggish Na+ kinetics, complex phase transitions, and poor air stability hinder their practical application. Herein, we proposed a dual-function strategy that not only precisely manipulates dynamic structural evolution from layered to tunnel structure, but also effectively suppresses Na+/vacancy and charge ordering by inhibiting electron delocalization. A series of Ti-substituted Na2/3Mn1-xTixO2 (x=0, 1/9, 2/9, 1/3) as proof of concept materials were designed to demonstrate the dual-function strategy. As a result, the optimized Na2/3Mn8/9Ti1/9O2 cathode material delivers a high specific capacity of 202.9 mAh g−1 at 0.1 C within 1.5−4.3 V, equivalent to 536.6 Wh kg−1 of energy density, and exhibits 71.0% of capacity retention after 300 cycles at 1 C. Meanwhile, a highly reversible P2/Tunnel-OP4/Tunnel phase transition process and interlocking effect between the layered and tunnel structure as well as prominent moisture stability even after soak water treatment are further confirmed by in-situ charge and discharge XRD and other advanced characterization techniques. Noting that the electrode assembled with water-solution binder still displays a high capacity retention of 85.4% after 400 cycles at 1 C. Our dual-function strategy provides valuable guidance for developing high energy density and water stable practical SIB cathode materials.

Designing a 3D framework NaVOPO4 as a high-power, low-strain and long-life positive electrode material for Na-ion batteries

Advances in sodium-ion batteries hugely rely on perfecting the performance of active electrode materials. In this paper, we offer a new NaVOPO4 polymorph adopting a KTiOPO4-type framework as a promising high-rate, low-strain and long-life positive electrode material for sodium-ion batteries. NaVOPO4 is prepared via a facile hydrothermally-assisted solid-state ion exchange. The crystal structure is refined based on synchrotron X-ray powder diffraction (XRD) and validated by X-ray absorption spectroscopy (XAS), transmission electron microscopy analysis and density functional theory (DFT) calculations. The electrochemical performance of NaVOPO4 is evaluated through galvanostatic charge/discharge tests, cyclic voltammetry, potentiostatic intermittent titration and electrochemical impedance spectroscopy. A carbon-coated NaVOPO4 demonstrates a specific capacity of ∼110 mAh g–1 at a C/10 rate at an average potential of ∼3.93 V vs. Na+/Na. The material exhibits decent capacity retention and rate capability, maintaining over 74 % of the initial capacity after 1000 cycles at a C/2 rate and around 87% at a 2C charge/discharge rate. Diffusion coefficients of 10–11 cm2 s–1 and DFT-calculated energy barriers of ∼0.15–0.35 eV indicate fast Na+ ion diffusion within the NaVOPO4 framework. The vanadium oxidation state and charge compensation mechanism in NaVOPO4 are studied by XAS and DFT. Moreover, the operando XRD analysis coupled with DFT elucidates several phase transitions occurring in NaVOPO4 with an exceptionally low volume variation of 2.4% in total, highlighting the reversibility and structural stability during Na+ de/insertion. Overall, NaVOPO4 exhibits attractive electrochemical performance and stability, making it a potential candidate for sodium-ion battery cathode materials.

Designing ultrastable P2/O3-type layered oxides for sodium ion batteries by regulating Na distribution and oxygen redox chemistry

P2/O3-type Ni/Mn-based layered oxides are promising cathode materials for sodium-ion batteries (SIBs) owing to their high energy density. However, exploring effective ways to enhance the synergy between the P2 and O3 phases remains a necessity. Herein, we design a P2/O3-type Na0.76Ni0.31Zn0.07Mn0.50Ti0.12O2 (NNZMT) with high chemical/electrochemical stability by enhancing the coupling between the two phases. For the first time, a unique Na+ extraction is observed from a Na-rich O3 phase by a Na-poor P2 phase and systematically investigated. This process is facilitated by Zn2+/Ti4+ dual doping and calcination condition regulation, allowing a higher Na+ content in the P2 phase with larger Na+ transport channels and enhancing Na+ transport kinetics. Because of reduced Na+ in the O3 phase, which increases the difficulty of H+/Na+ exchange, the hydrostability of the O3 phase in NNZMT is considerably improved. Furthermore, Zn2+/Ti4+ presence in NNZMT synergistically regulates oxygen redox chemistry, which effectively suppresses O2/CO2 gas release and electrolyte decomposition, and completely inhibits phase transitions above 4.0 V. As a result, NNZMT achieves a high discharge capacity of 144.8 mA h g−1 with a median voltage of 3.42 V at 20 mA g−1 and exhibits excellent cycling performance with a capacity retention of 77.3% for 1000 cycles at 2000 mA g−1. This study provides an effective strategy and new insights into the design of high-performance layered-oxide cathode materials with enhanced structure/interface stability for SIBs.

O3‐Type Cathodes for Sodium‐Ion Batteries: Recent Advancements and Future Perspectives

AbstractOver recent decades, rapid advancements in energy technology have transformed human life. Lithium‐ion batteries (LIBs) have played a pivotal role nevertheless concerns about limited lithium resources and price fluctuations underscore the need for sustainability. Sodium‐ion batteries (SIBs), operating on principles akin to LIBs, have emerged as promising candidates for rechargeable batteries in the next generation of energy storage systems, primarily due to their cost‐effectiveness and sustainable attributes. Analogous to LIBs, the cathode in SIBs assumes a critical role in dictating the electrochemical performance of the battery. Therefore, the research and development of cathode materials for SIBs take on paramount significance. O3‐type SIB cathodes, inspired by the successful O3‐type LIB cathodes (e. g., LiCoO2 and NMC variants), hold promise for commercial applications. This comprehensive overview offers an in‐depth exploration of various unary‐metal oxide cathode materials characterized by an O3‐layered structure. Subsequently, nickel (Ni), manganese (Mn), and Ni/Mn‐based O3 cathode materials are conducted a comprehensive study, assessing the effects of element substitution and doping on capacity, phase transitions, and cycle life. In light of the current challenges, advancing SIB cathode materials of future directions will propose, addressing key considerations in the pursuit of enhanced performance and sustainable energy storage solutions.

Inducing Na+ Site Rearrangement Through a Cosubstitution Strategy for Rapid Na Diffusion Kinetics of P2-Type Layered Metal Oxides.

The P2-layered metal oxide cathode materials are crucial for constructing high-rate sodium-ion batteries (SIBs); however, its practical application is hindered by the high Na+ diffusion barrier resulting from Na+/vacancy ordering. Herein, a Li/Zn cosubstitution P2-Na0.67Ni0.33Mn0.67O2 (NLNZM) cathode was synthesized via a sol-gel method assisted with citric acid, which can induce the rearrangement of Na+ sites to disrupt ordered structures. The XRD Rietveld refinement confirms a higher occupancy of Na+ at Nae sites with low diffusion barriers through the Li/Zn cosubstitution. In addition, the highly reversible phase evolution of the NLNZM is confirmed through in situ XRD results, thereby ensuring the stability of the structure with low volume change rate (0.78%). Furthermore, Li and Zn can reduce the surface energy and increase the interlayered distance to achieve rapid interfacial kinetics. As a result, the NLNZM has exhibited a high reversible capacity of 152.8 mAh g-1 and an outstanding rate performance of 103.4 mAh g-1 at 5C. After 200 cycles at 5C, the capacity retention rate is 81.1%. This work proposes a cosubstitution strategy to induce Na+/vacancy disorder for achieving rapid Na+ migration as a cathode material for SIBs.

Solid-phase construction of high-performance sodium-ion battery cathode materials with three-dimensional porous structure: Na4MnCr(PO4)3/C

Na4MnCr(PO4)3 is a promising cathode material with high redox potential and high energy density, but the intrinsic poor electronic conductivity and substandard structural stability restrict its practical application. Herein, porous Na4MnCr(PO4)3/C with conductive networks and improved electrochemical properties is synthesized by a facile modified solid-state process using citric acid as a multifunctional additive. The results reveal that citric acid can be used as a grinding aid to make the raw materials mix more evenly and speed up the efficiency of ball milling. Besides, 3D conductive network and porous structure originated from polycondensation and carbonization of citric acid can promote the electrochemical properties of Na4MnCr(PO4)3/C by enhancing the electronic/ionic conductivity and (de)intercalation reaction kinetics. As expected, the optimal Na4MnCr(PO4)3/C delivers a high reversible capacity of 130.5 mAh g−1 at 0.1C rate, and exhibits a capacity retention of 82.62% at 10C rate after 500 cycles. In addition, the reversible biphasic reaction of the cathode is confirmed by the constant galvanostatic intermittent titration technique and ex-situ XRD, which shows great potential of the synthesized Na4MnCr(PO4)3/C for practical applications.

Advances in layered transition metal oxide cathodes for sodium-ion batteries

The rapid rise of renewable energy technology has greatly promoted the development of energy storage systems. Breaking decades of stagnation, sodium-ion batteries (SIBs) have now regained momentum in the field of energy storage and they are considered as a low-cost alternative to lithium-ion batteries. The search for suitable materials to reversibly host sodium ions has become a focal point in SIB field. Layered transition metal oxide (NaxTMO2) as the cathode material has attracted increasing attention due to its simple structure, facile synthesis, and high operating potential. Nevertheless, NaxTMO2 still faces severe challenges, including irreversible phase transitions, storage instability, insufficient performance, etc. This work provides a comprehensive review of NaxTMO2 as the cathode material for SIBs, analyzes the challenges encountered by NaxTMO2, and summarizes effective improvement strategies. Strategies including doping, composite cathode materials, high-entropy materials and microstructural modulation can effectively guide the design of NaxTMO2 with excellent performance. SIBs are bound to play a positive role in the new round of energy revolution.

Yolk-Shell Construction of Na3V2(PO4)2F3 with Copper Substitution Microsphere as High-Rate and Long-Cycling Cathode Materials for Sodium-Ion Batteries.

Na3V2(PO4)2F3 (NVPF) is emerging as a promising cathode material for high-voltage sodium-ion batteries. Whereas, the inferior intrinsic electrical conductivity leading to poor rate performance and cycling stability. To address this issue, a strategy of synthesizing unique yolk-shell structured NVPF with copper substitution via spray drying method is proposed. Besides, the synergistic modulation of both crystalline structure and interfacial properties results in significantly enhanced intrinsic and interfacial conductivity of NVPF. The optimized yolk-shell structured cathode materials can possess a high capacity of 117.4 mAh g-1 at 0.1 C, and remains a high-capacity retention of 91.3% after 5000 cycles. A detailed investigation of kinetic properties combined with in situ XRD technology and DFT calculations, has been implemented, particularly with regard toelectron conduction and sodium ion diffusion. Consequently, the yolk-shell structured composition of Na3V1.94Cu0.06(PO4)2F3 with nitrogen-modified carbon coating layer shows the lowest polarization potential because of the effectively enhanced electronic conductivity and Na+ diffusion process in the bulk phase. The robust electrochemical performance suggests that developing the unique yolk-shell structure with the collaboration of interface and bulk crystal properties is a favorable strategy to design cathode material with a high performance for sodium-ion batteries.

Cation/Anion-Dual regulation in Na3MnTi(PO4)3 cathode achieves the enhanced electrochemical properties of Sodium-Ion batteries

Na3MnTi(PO4)3 (NMTP) emerges as a promising cathode material with high-performance for sodium-ion batteries (SIBs). Nevertheless, its development has been limited by several challenges, including poor electronic conductivity, the Mn3+ Jahn-Teller effect, and the presence of a Na+/Mn2+ cation mixture. To address these issues, we have developed a cation/anion-dual regulation strategy to activate the redox reactions involving manganese, thereby significantly enhancing the performance of NMTP. This strategy simultaneously enhances the structural dynamics and facilitates rapid ion transport at high rates by inducing the formation of sodium vacancy. The combined effects of these modifications lead to a substantial improvement in specific capacity (79.1 mAh/g), outstanding high-rate capabilities (35.9 mAh/g at 10C), and an ultralong cycle life (only 0.040 % capacity attenuation per cycle over 250 cycles at 1C for Na3.34Mn1.2Ti0.8(PO3.98F0.02)3) when used as a cathode material in SIBs. Furthermore, its performance in full cell demonstrates impressive rate capability (44.4 mAh/g at 5C) and exceptional cycling stability (with only 0.116 % capacity decay per cycle after 150 cycles at 1C), suggesting its potential for practical applications. This work presents a dual regulation strategy targeting different sites, offering a significant advancement in the development of NASICON phosphate cathodes for SIBs.

Rapid mechanochemical synthesis of high-performance Na4Fe2.94Al0.04(PO4)2(P2O7)/C cathode material for sodium-ion storage

Na4Fe3(PO4)2(P2O7) is regarded as a promising cathode material for sodium-ion batteries due to its affordability, non-toxic nature, and excellent structural stability. However, its electrochemical performance is hampered by its poor electronic conductivity. Meanwhile, most of the previous studies utilized spray-drying and sol–gel methods to synthesize Na4Fe3(PO4)2(P2O7), and the large-scale synthesis of the cathode material is still challenging. This study presents a composite cathode material, Na4Fe2.94Al0.04(PO4)2(P2O7)/C, prepared via a straightforward ball-milling technique. By substituting Al3+ minimally into the Fe2+ site of NFPP, Fe defects are introduced into the structure, hindering the formation of NaFePO4 and thereby enhancing Na-ion diffusion kinetics and conductivity. Additionally, the average length of AlO bonds (2.18 Å) is slightly smaller than that of FeO bonds (2.19 Å), contributing to the superior structural stability. The smaller ionic radii of Al3+ induce lattice contraction, further enhancing the structural stability. Moreover, the surface of material particles is coated with a thin layer of carbon, ensuring excellent electrical conductivity and outstanding structure stability. As a result, the Na4Fe2.94Al0.04(PO4)2(P2O7)/C cathode exhibits excellent electrochemical performance, leading to high discharge capacity (128.1 mAh g−1 at 0.2 C), outstanding rate performance (98.1 mAh g−1 at 10 C), and long cycle stability (83.7 % capacity retention after 3000 cycles at 10 C). This study demonstrates a low-cost, ultra-stable, and high-rate cathode material prepared by simple mechanical activation for sodium-ion batteries which has application prospects for large-scale production.

Achieving structurally stable O3-type layered oxide cathodes through site-specific cation-anion co-substitution for sodium-ion batteries

O3-type layered oxides have garnered great attention as cathode materials for sodium-ion batteries because of their abundant reserves and high theoretical capacity. However, challenges persist in the form of uncontrollable phase transitions and intricate Na+ diffusion pathways during cycling, resulting in compromised structural stability and reduced capacity over cycles. This study introduces a special approach employing site-specific Ca/F co-substitution within the layered structure of O3-NaNi0.5Mn0.5O2 to effectively address these issues. Herein, the strategically site-specific doping of Ca into Na sites and F into O sites not only expands the Na+ diffusion pathways but also orchestrates a mild phase transition by suppressing the Na+/vacancy ordering and providing strong metal–oxygen bonding strength, respectively. The as-synthesized Na0.95Ca0.05Ni0.5Mn0.5O1.95F0.05 (NNMO-CaF) exhibits a mild O3 → O3 + O'3 → P3 phase transition with minimized interlayer distance variation, leading to enhanced structural integrity and stability over extended cycles. As a result, NNMO-CaF delivers a high specific capacity of 119.5 mA h g−1 at a current density of 120 mA g−1 with a capacity retention of 87.1% after 100 cycles. This study presents a promising strategy to mitigate the challenges posed by multiple phase transitions and augment Na+ diffusion kinetics, thus paving the way for high-performance layered cathode materials in sodium-ion batteries.

Exploring the Effect of V2O5 and Nb2O5 Content on the Structural, Thermal, and Electrical Characteristics of Sodium Phosphate Glasses and Glass-Ceramics.

Na-V-P-Nb-based materials have gained substantial recognition as cathode materials in high-rate sodium-ion batteries due to their unique properties and compositions, comprising both alkali and transition metal ions, which allow them to exhibit a mixed ionic-polaronic conduction mechanism. In this study, the impact of introducing two transition metal oxides, V2O5 and Nb2O5, on the thermal, (micro)structural, and electrical properties of the 35Na2O-25V2O5-(40 - x)P2O5 - xNb2O5 system is examined. The starting glass shows the highest values of DC conductivity, σDC, reaching 1.45 × 10-8 Ω-1 cm-1 at 303 K, along with a glass transition temperature, Tg, of 371 °C. The incorporation of Nb2O5 influences both σDC and Tg, resulting in non-linear trends, with the lowest values observed for the glass with x = 20 mol%. Electron paramagnetic resonance measurements and vibrational spectroscopy results suggest that the observed non-monotonic trend in σDC arises from a diminishing contribution of polaronic conductivity due to the decrease in the relative number of V4+ ions and the introduction of Nb2O5, which disrupts the predominantly mixed vanadate-phosphate network within the starting glasses, consequently impeding polaronic transport. The mechanism of electrical transport is investigated using the model-free Summerfield scaling procedure, revealing the presence of mixed ionic-polaronic conductivity in glasses where x < 10 mol%, whereas for x ≥ 10 mol%, the ionic conductivity mechanism becomes prominent. To assess the impact of the V2O5 content on the electrical transport mechanism, a comparative analysis of two analogue series with varying V2O5 content (10 and 25 mol%) is conducted to evaluate the extent of its polaronic contribution.

Electrochemical Performance of Na2Mn3O7 as a Cathode Material in Sodium-Ion Batteries Using the Precipitation Method with Ethylene Glycol Chelating Agent

Tests were conducted on Na2Mn3O7 as a cathode material in sodium-ion batteries, aiming to synthesize Na2Mn3O7 precursor using commercial and synthetic MnCO3 variants. Sample A utilized commercial MnCO3, while sample B utilized MnCO3 synthesized from MnSO4.1H2O and Na2CO3. Both variants were mixed with Na2CO3 to form Na2Mn3O7 precursor, which was then sintered at 700°C for 4 hours, ground, and sieved. A slurry was prepared by mixing the active materials PVDF: Super P in an 8:1:1 ratio with 3.5 mL of NMP. Sample A exhibited a conductivity of 3.4706×10-7 S/cm, and sample B had a conductivity of 2.7304×10-7 S/cm in the EIS results. In the CV test, sample A showed oxidation and reduction peaks at 2.77 V and 1.62 V, respectively, while sample B had peaks at 2.842 V and1.716 V. In the CD test, sample A reached maximum and minimum peaks of 4.3 V and 1.4 V, while sample B reached peaks of 4.2 V and 1.3 V. Sample A exhibited a capacity of 117.02 mAh/g on charge and 93.47 mAh/g on discharge, whereas sample B showed capacities of 79.17 mAh/g on charge and 65.79 mAh/g on discharge. These results indicate the superior performance of sample A over sample B.

Synergetic enhancement of structural stability and kinetics of P’2-type layered cathode for sodium-ion batteries via cation–anion co-doping

The P’2-type layered oxides attract much attention as viable cathode materials for sodium-ion batteries (SIBs), due to their high specific capacity and environmental friendliness. Nevertheless, the sluggish Na+ diffusion kinetics and drastic capacity decay triggered by irreversible phase transition limit their large-scale application. In this study, we employ a synergistic optimization strategy involving cation and anion dopants to successfully restrain intergranular strain and tune local electronic structure, strengthening structural stability and electrochemical performance of the cathode material. Specifically, the Mg2+ dopant suppresses Na+/vacancy rearrangement and Mn-O anisotropic changes, while the F− dopant facilitates Na+ transport and alleviates phase evolution in high-voltage regions. Through this co-doping design, the modified electrodes display more alleviated voltage decay and exceptional capacity retention enhancements ranging from 6.57 % to 81.23 % after 750 cycles at 1000 mA g–1. This work provides novel perspectives on precise design of cathode materials, making layered oxides promising contenders for the next generation energy storage systems.

Selective recovery of metals in spent batteries by electrochemical precipitation to cathode material for sodium-ion batteries

The recycling of key components in waste lithium-ion batteries (LIBs) is an important route to make up for the shortage of battery materials. Metal separation and purification is an important step. It is of great significance to propose an efficient and green separation technology. In this paper, an electrochemical precipitation method was applied to metal separation from spent LiNi0.5Mn1.5O4 cathode material. The Li and metal elements were effective separated and the precipitates were then used as precursor to synthesize high-performance R–O3-NaNFM cathode material for sodium-ion batteries. The R–O3-NaNFM exhibits excellent electrochemical cycling stability. The capacity retains 71.3 mAh g−1 after a long-term cycling of 200 times at 1 C. This method offers a referable strategy of the recycling for the waste cathode material in spent LIBs.

Unveiling charge compensation mechanisms in Na2/3MgxNi1/3-xMn2/3O2 cathode materials: insights into cationic and anionic redox

P2-type Na2/3Ni1/3Mn2/3O2 cathode material for sodium-ion batteries exhibits negligible voltage hysteresis during charge and discharge cycles, with oxygen redox mechanisms playing a pivotal, non-negligible role. Conversely, for the Na2/3Mg1/3Mn2/3O2 material featuring Mg substitution for Ni, O redox largely governs the entire charge and discharge process, accompanied by a pronounced voltage hysteresis. Upon combining these two materials – Na2/3MgxNi1/3-xMn2/3O2 – the transition metal and O redox processes, constituting the charge compensation mechanism, become paramount. These phenomena underscore the transition metal's influence on anionic redox, a topic with limited in-depth exploration in the existing literature. Within this study, we synthesized two materials, Na2/3Mg1/9Ni2/9Mn2/3O2 and Na2/3Mg2/9Ni1/9Mn2/3O2 (Mg-0.11, Mg-0.22), subsequently probing their transition metal and oxygen redox contributions to electrochemical capacity during the initial and 10th cycle charge and discharge processes by synchrotron-based mapping of resonant inelastic X-ray scattering and soft X-ray Absorption Spectroscopy. Our findings corroborate the presence of similar O redox contributions in the Mg-substituted materials. Intriguingly, the Mg-0.11 material exhibits a substantial enhancement in O redox following ten cycles, warranting further investigation due to its exceptional multiplicity, cycling performance, minimal voltage hysteresis, and potential impact on advancing sodium-ion battery commercialization.

Vacancies-regulated Prussian Blue Analogues through Precipitation Conversion for Cathodes in Sodium-ion Batteries with Energy Densities over 500 Wh/kg.

Prussian blue analogues (PBAs) have been widely applied in many fields, especially as cathode materials of sodium-ion batteries on account of their low cost and open framework for fast ions transport. However, the capacity of reported PBAs has a great distance from its theoretical value. Herein, we proposed that [Fe(CN)6 ] vacancies are crucial point for the high specific capacity for the first time. The [Fe(CN)6 ] vacancies may create net electrons and reduce obstacles to ionic transport, which is conducive to rate performance of PBAs by increasing electronic and ionic conductivity to some extent. As a proof of concept, a series of PBAs have been prepared by co-precipitation method. And then, a novel precipitation conversion method has been designed, by which unique PBAs with a specific quantity of [Fe(CN)6 ] vacancies was successfully synthesized. Remarkably, the as-prepared PBAs possessing hierarchical hollow morphology have reached a unprecedent level of high capacity (168 mAh g-1 at 25 mA g-1 , close to PBAs' theoretical capacity 170 mAh g-1 ), high rate performance (90 mAh g-1 at 5 A g-1 ), and high energy density (over 500 Wh kg-1 ).

P2/O3 Biphasic Cathode Material through Magnesium Substitution for Sodium-Ion Batteries.

P2-type Fe-Mn-based oxides offer excellent discharge specific capacity and are as affordable as typical layered oxide cathode materials for sodium-ion batteries (SIBs). After Cu modification, though they can improve the cycling performance and air stability, the discharge specific capacity will be reduced. Considering the complementary nature of biphasic phases in electrochemistry, hybridizing P2/O3 hybrid phases can enhance both the storage performance of the battery and specific capacity. Herein, a hybrid phase composite with high capacity and good cycle performance is deliberately designed and successfully prepared by controlling the amount of Mg doping in the layered oxide. It has been found that the introduction of Mg can activate anion redox in the oxide layer, resulting in a significant increase in the specific discharge capacity of the material. Meanwhile, the dual-phase structure can produce an interlocking effect, thus effectively alleviating structure strain. The degradation of cycling performance caused by structural damage during the high-voltage charging and discharging process is clearly mitigated. The results show that the specific discharge capacity of Na0.67Cu0.2Mg0.1Fe0.2Mn0.5O2 is as high as 212.0 mAh g-1 at 0.1C rate and 186.2 mAh g-1 at 0.2C rate. After 80 cycles, the capacity can still maintain 88.1%. Moreover, the capacity and cycle performance as well as the stability can still remain stable even in the high-voltage window. Therefore, this work offers an insightful exploration for the development of composite cathode materials for SIBs.

Fluoride Doping Na3Al2/3V4/3(PO4)3 Microspheres As Cathode Materials for Sodium-Ion Batteries with Multielectron Redox.

Sodium-ion batteries (SIBs) are potential candidates for large energy storage usage because of the natural abundance and cheap sodium. Nevertheless, improving the energy density and cycling steadiness of SIB cathodes remains a challenge. In this work, F-doping Na3Al2/3V4/3(PO4)3(NAVP) microspheres (Na3Al2/3V4/3(PO4)2.9F0.3(NAVPF)) are synthesized via spray drying and investigated as SIB cathodes. XRD and Rietveld refinement reveal expanded lattice parameters for NAVPF compared to the undoped sample, and the successful cation doping into the Na superionic conductor (NASICON) framework improves Na+ diffusion channels. The NAVPF delivers an ultrahigh capacity of 148 mAh g-1 at 100mA g-1 with 90.8% retention after 200 cycles, enabled by the activation of V2+/V5+ multielectron reaction. Notably, NAVPF delivers an ultrahigh rate performance, with a discharge capacity of 83.6 mAh g-1 at 5000mA g-1. In situ XRD demonstrates solid-solution reactions occurred during charge-discharge of NAVPF without two-phase reactions, indicating enhanced structural stability after F-doped. The full cell with NAVPF cathode and Na+ preintercalated hard carbon anode shows a large discharge capacity of 100 mAh g-1 at 100mA g-1 with 80.2% retention after 100 cycles. This anion doping strategy creates a promising SIB cathode candidate for future high-energy-density energy storage applications.