Catalytic System Research Articles

Frustrated Lewis pairs on facet-engineered CeO2 boost the conversion of low-concentration CO2 into cyclic ureas with assistance of diamine platforms

The development of efficient processes for value-added utilization of low-concentration CO2 is an on-going challenge. In this work, we present a sequential system based on diamine platforms for the direct utilization of low-concentration sources of CO2 (≤15%) in the production of cyclic ureas. Specifically, the low-concentration CO2 is captured by ethylenediamine to form ethylenediamine carbamate (EDA-CA), which subsequently undergoes the intramolecular dehydration to give ethyleneurea (EU) in the presence of frustrated Lewis pairs (FLPs) on the facet-engineered CeO2. Remarkably, the productivity of EU obtained from EDA-CA in the sequential system (9.5 mmol·gcat−1·h−1) is ∼4 times higher compared to the traditional catalytic system (2.4 mmol·gcat−1·h−1) using ethylenediamine and pure CO2 (3 MPa). Density functional theory calculations demonstrated that the FLPs on facet-engineered CeO2 significantly reduce the energy barrier for the nucleophilic attack of N-containing segment towards the carbonyl carbon in EDA-CA (rate-limiting step), ultimately optimizing the intramolecular cyclization efficiency of EDA-CA. This work not only provides an innovation tandem approach that enables the production of cyclic ureas from low-concentration CO2, but also opens up a promising avenue for the direct utilization of low-concentration CO2 for value-added applications in the future.

Photocatalytic regeneration of nicotinamide cofactor biomimetics drives biocatalytic reduction by Old Yellow enzymes

A key approach in developing green chemistry involves converting solar energy into chemical energy of biomolecules through photocatalysis. Photocatalysis can facilitate the regeneration of nicotinamide cofactors during redox processes. Nicotinamide cofactor biomimetics (NCBs) are economical substitutes for natural cofactors. Here, photocatalytic regeneration of NADH and reduced NCBs (NCBsred) using graphitic carbon nitride (g-C3N4) was developed. The process involves g-C3N4 as the photocatalyst, Cp*Rh(bpy)H2O2+ as the electron mediator, and Triethanolamine as the electron donor, facilitating the reduction of NAD+ and various oxidative NCBs (NCBsox) under light irradiation. Notably, the highest reduction yield of 48.32 % was achieved with BANA+, outperforming the natural cofactor NAD+. Electrochemical analysis reveals that the reduction efficiency and capacity of cofactors relies on their redox potentials. Additionally, a coupled photo-enzymatic catalysis system was explored for the reduction of 4-Ketoisophorone by Old Yellow Enzyme XenA. Among all the NCBsox and NAD+, the highest conversion ratio of over 99 % was obtained with BANA+. After recycled for 8 times, g-C3N4 maintained over 93.6 % catalytic efficiency. The photocatalytic cofactor regeneration showcases its outstanding performance with NAD+ as well as NCBsox. This work significantly advances the development of photocatalytic cofactor regeneration for artificial cofactors and its potential application.

Photochemical Synthesis of Chiral Heterocycles via Asymmetric Carbon‐Heteroatom Bond Formation

Chiral heterocyclic compounds play a crucial role in the pharmaceutical science, materials science, and agrochemical industries. The critical step for synthesizing chiral heterocycles is the formation of asymmetric carbon‐heteroatom bonds, which can be achieved in a chiral environment under thermal or photochemical conditions. However, photochemical asymmetric transformation has become an area of immense growth in the past 15 years. In the drug discovery and development era, chiral photochemical transformations have drawn the attention of researchers to develop new synthetic strategies for chiral heterocycles via asymmetric carbon‐heteroatom bond formation. Chiral photochemistry in the pathway of asymmetric synthesis requires a chirality source which is transferred to the products. A catalytic chiral metal complexing agent or a chiral photosensitizer that generally follows a single electron transfer (SET) or oxidative and reductive quenching cycle has been widely exploited to achieve this goal. In this review, we have demonstrated the recent development of photochemical synthesis of chiral heterocycles via asymmetric carbon‐heteroatom bond formation by using a chiral metal catalyst, asymmetric organocatalyst, or dual catalytic system based on their plausible mechanism.

MOX-TiO2 (M=Pt, Pd, Ru) for alcoholysis reaction from furfuryl alcohol to ethyl levulinate

Simple noble metal oxides (PtOx, PdOx, RuOx) based titanium dioxide (Pt–TiO2, Pd–TiO2, Ru–TiO2) were prepared using a facile sol-gel method. The conversion of furfuryl alcohol (FAL) to ethyl levulinate (EL) was studied. Full characterizations were performed using XRD, XPS, Raman and in situ FT-IR. An in-depth study of acidic strength and sites distribution (Brønsted or Lewis) was conducted by NH3-TPD, pyridine-IR. The profiles of H2-TPR and O2-TPD suggested enhanced reducibility and optimum oxygen storage capacity in Pt–TiO2. Remarkable FAL conversion (94.4%), EL yield (89.6%) with productivity (21.3 × 103 molEL/mmolPt h) and TOF (22.5 × 103 molFAL/mmolPt h) were obtained. Metal productivity follows the order: Pt (21.3 × 103 molEL/mmolPt h) > Ru (11.5 × 103 molEL/mmolRu h) > Pd (3.6 × 103 molEL/mmolPd h). Two different reaction pathways were proposed. From computational calculations of charge density differences and Ead value, a robust electron transfer capacity was found in Pt–TiO2, as well as an advantageous FAL adsorption as compared to other catalytic systems.

Tandem photocatalysis of nitrate to nitrogen on Cu@CN/TiOx S-scheme heterojunction

The persistent challenge of nitrate (NO3–) pollution in water systems, profoundly impacting ecosystems and human health, demands effective remediation strategies. Here, we present an innovative S-scheme Cu@CN/TiOx heterojunction for high-efficiency photocatalytic denitrification (PCDN). Evaluation of its performance demonstrates exceptional NO3– removal efficiency (99.5%) and remarkable N2 selectivity (95.5%), with 13.7 and 4.1 times higher rate constants of NO3– removal than the individual Cu@CN and TiOx components. Notably, this catalyst exhibits impressive stability across multiple cycles, maintaining consistent high conversion rates and selectivity. Mechanistic insights unveiled a tandem reaction pathway where Cu@CN selectively reduced NO3– to NO2–, followed by the TiOx-mediated CO2•– generation, enabling highly selective NO2– to N2 conversion. This unique catalytic system, featuring spatially separated redox-active sites, presents a promising avenue for efficient, selective, and stable denitrification processes, offering significant potential in addressing water pollution challenges and advancing tandem catalytic systems.

Reduction of the harmful NOx pollutants emitted from the ship engines using high-pressure selective catalytic reduction system.

Various techniques are used to reduce harmful pollutants such as NOX emissions from ships. Selective catalyst reduction (SCR) systems are the most effective technique used to reduce NOX emissions. In this study, the effects of an SCR reactor on NOX emissions and performance in high-pressure selective catalytic reduction (HP-SCR) systems were investigated numerically. In numerical studies, the effects of SCR system diameter, output form, catalyst activation energy, mixing zone length, and location were investigated as parametric, and the most suitable system geometry was determined. The effects of geometric parameters and catalyst type on emission and performance such as NOX reduction, NH3 slip, velocity, and pressure loss were investigated. It was determined that with increasing system diameter, whereas the NOX reduction performance increased depending on exhaust velocity, the pressure drop decreased, and the most suitable system diameter was determined as 780 mm. Furthermore, the obtained results showed that the performance of NOX reduction decreased after 2 × 106 kJ/kmol activation energy, and the most suitable SCR output form was conical geometry. In terms of the environment, this study will contribute to achieving the UN Sustainable Development Goals such as climate action (SDG 13).

Solvent Effects on Heterogeneous Catalysis for the Selective Hydrogenation

AbstractSolvent effects add a new dimension for tuning the activity and selectivity of heterogeneous catalytic reactions, which is extensively employed in the hydrogenation of unsaturated compounds with multiple functional groups. In this concept, we briefly summarize recent developments on how the solvent effects affect the catalytic performance from the following aspects: 1) the polarity of the solvent can influence the interaction between the solvent and the reactant or intermediate; 2) the composition of mixed solvent can influence the reactivity of the reactant or intermediate; 3) solvent effect varies with the metal identity and support; 4) the solvent can induce surface modification of the supported catalysts. This summarization will provide insights into the rational development of efficient and selective heterogeneous hydrogenation catalytic system to realize the precise synthesis of desired chemicals.

Organoboron-Promoted Electrochemical Chlorosulfonylation of Alkenes with Sulfonyl Chlorides.

Although extraordinary advances have been achieved by the transition-metal catalysis system, there is an urgent need to explore and develop alternative methodologies that are more environmentally friendly. Herein, we report an electrochemical chlorosulfonylation of alkenes using a wide range of sulfonyl chlorides with an inexpensive, degradable, and commercially available organoboron as a promoter. Furthermore, this protocol employs convergent paired electrolysis, reducing the need for sacrificial anodes and minimizing the extent of hydrogen evolution.

The use of methanol as a C1 building block.

Methanol is a key building block in the chemical industry. In recent years, it has been used as a C1 source in various organic transformations in the presence of a transition-metal catalyst. This protocol describes the ruthenium- and cobalt-catalyzed utilization of methanol in different types of methylation reactions and heterocycle synthesis. Initially, we describe the synthesis of tridentate ligands (L1-L3) and their corresponding Ru(II) complexes (Ru-1, -2 and -3) and then detail how to apply these Ru(II) complexes and Co/PP3 (PP3 = P(CH2CH2PPh2)3) in various methanol dehydrogenative coupling reactions. We discuss six types of transformations by using methanol or a methanol/water mixture. The experimental setup for all the catalytic reactions is similar and involves adding all the respective reagents and solvents to an argon-filled pressure tube, which is sealed (by screw cap) and refluxed at the indicated temperature before the desired products are isolated and characterized. The catalytic systems described in this protocol work well for both small-scale and preparative-scale synthesis of various N-methylated amines/amides, C-methylated products and quinazolinones. These catalytic reactions are greener and more sustainable than conventional synthesis methods, with only H2 and/or H2O as by-products, and we evaluate the 'green chemistry metrics' for a typical substrate. The total time required for the catalytic experiments described in this protocol is 16-28 h, and the operation time is 4 h. An average level of expertise in organic synthesis is required to carry out these protocols.

Chiral Lewis Base/Achiral Acid Co‐Catalyzed Atroposelective Sulfenylation of Pyrrole Derivatives: Construction of C—N Axially Chiral Sulfides

Comprehensive SummaryChiral BINAM‐derived selenide/achiral acid co‐catalyzed atroposelective electrophilic sulfenylation of pyrrole derivatives has been realized for the first time. A variety of C—N axially chiral sulfur‐containing pyrrole derivatives were readily obtained in moderate to good yields with moderate to excellent enantioselectivities. This catalytic system involves sequential desymmetrization and kinetic resolution.

Enhancing the performance of catalytic membranes for simultaneous degradation of dissolved organic phosphonates and phosphorous recovery: A fit-for-purpose loose nanofiltration design

In this study, we developed a loose nanofiltration catalytic membrane (LNCM) by incorporating nitrogen-doped carbon nanotubes (NCNT) into graphene oxide (GO) membrane (NCNT@GO-M) to activate peroxymonosulfate for efficient phosphonates degradation into phosphate, reducing phosphorus-based pollution and facilitating P recovery. The NCNT@GO-M exhibited superior permeability (76.7 L m−2 h−1 bar−1) due to its expanded pore size (1.60 nm). It integrated nanoconfinement and surface catalysis, improving the availability of surface-bound sulfate radicals for rapid Orth-P generation (kobs, 1.93 s−1), with the kobs being 2.4 times higher than that of the NCNT membrane catalytic system and 2626 times higher than the NCNT@GO heterogeneous catalytic system. The NCNT@GO-M also demonstrated excellent antifouling, self-cleaning, and anti-interference ability, effectively retaining humic acid with a molecular weight exceeding 3.6 kDa (∼62% removal of dissolved organic carbon), making it suitable for real-water applications. The development of LNCM shows great potential for transforming and recovery of the nutrients in wastewater.

Selectivity Switch in Non‐Directed Palladium‐Catalyzed C‐H Olefination of Chlorobenzene Derivatives

A palladium(II)‐catalyzed oxidative C‐H olefination of chlorobenzene derivatives, which favored the functionalization at the ortho‐to‐chlorine position, was reported. The catalytic system employed a commercially available quinoline ligand to access a wide panel of olefinated aryl chlorides in moderate to high yields from feedstock chemicals (42 examples, 28 to 93% yields). The synthetic utility of the method was further demonstrated by the coupling of various bio‐relevant acrylate partners offering straightforward access to structurally diverse complex molecules. A computational study of the reaction allowed us to confirm that the C‐H activation step, occurring through a concerted metalation‐deprotonation mechanism, determined the site‐selectivity of the transformation. The regioselectivity was controlled by the pKa of the C‐H bond (more acidic position) and the lower distortion of chlorobenzene in the key transition structure.

Ultrahigh-Performance Fiber-Supported Iron-Based Ionic Liquid for Synthesizing 3,4-Dihydropyrimidin-2-(1H)-ones in a Cleaner Manner.

Herein, a fiber-supported iron-based ionic liquid as a type of fibrous catalyst has been developed for the synthesis of bioactive 3,4-dihydropyrimidin-2-(1H)-ones (DHPMs) via three-component Biginelli reactions in a cleaner manner. The described fibrous catalyst was obtained from the commercially available polyetheretherketone (PEEK) fiber by postfunctionalization processes and was characterized and analyzed in detail by means of diversified technologies. Furthermore, the fiber-supported iron-based ionic liquids could mediate the classical three-component Biginelli reactions to proceed smoothly to gain a variety of substituted DHPMs with yields of up to 99%. The superior catalytic activities of the fibrous catalyst were ascribed to the quasi-homogeneous medium by ionic liquids generated in the surface layer of the PEEK fiber, which could afford an appropriate reaction zone and could further be available for the aggregation of substrates to facilitate the three-component reaction. Notably, the fibrous catalyst is available for recycling over 10 runs just by a pair of tweezers, and the operational procedure was capable of enlarging the catalytic system to the gram-scale without any performance degradation, which provided a cleaner manner to take advantage of the iron-based catalyst in organic synthesis with potential industrialization prospects.

Fe-TiO2-x/TiO2 S-scheme homojunction for efficient photocatalytic CO2 reduction

CO2-to-high value-added chemicals via a photocatalytic route is of interest but strangled by the low efficiency. Herein, a novel Fe-TiO2-x/TiO2 S-scheme homojunction was designed and constructed by using a facile surface modification approach whereby oxygen vacancy (OV) and Fe introducing on the TiO2 nanorod surface. The as-synthesized Fe-TiO2-x/TiO2 S-scheme homojunction exhibits positive properties on promoting photocatalytic CO2 reduction: i) the nanorod structure provides numerous active sites and a radical charge transfer path; ii) the doped Fe and OV not only synergistically enhance light utilization but also promote CO2 adsorption; iii) the Fe-TiO2-x/TiO2 S-scheme homojunction benefits photoexcited charge separation and retains stronger redox capacity. Thanks to those good characters, the Fe-TiO2-x/TiO2 homojunction exhibits superior CO2 reduction performances with optimized CO/CH4 generation rates of 122/22 μmol g-1h−1 which exceed those of pure TiO2 by more than 9.4/7.3 folds and most currently reported catalytic systems. This manuscript develops a facile and universal approach to synthesize well-defined homojunction and may inspire the construction of other more high-efficiency photocatalysts toward CO2 reduction and beyond.

Electrocatalytic Conversion of Small Molecules Utilizing Concerted Proton-electron Transfer Mediators.

Activation of small molecules such as CO2, N2 or organic substrates and their subsequent transformation into complex value-added chemicals by electrocatalysis, utilizing renewable energy sources under ambient conditions, has gained considerable interest in the last few years. However, activation of these chemically inert molecules is hindered by their intrinsically high activation energy barrier presupposing the development of tailored catalytic systems, often precluding selective transformation to the desired target products. Recent studies have shown that the utilization of concerted proton-electron transfer (CPET) mediators (med-H) may facilitate these challenging electrocatalytic reactions.

Insights into Fischer–Tropsch catalysis: current perspectives, mechanisms, and emerging trends in energy research

Fischer–Tropsch (FT) synthesis is an important module for the production of clean and sustainable fuels and chemicals, making it a topic of considerable interest in energy research. This mini-review covers the current literature on FT catalysis and offers insights into the primary products, the nuances of the FT reaction, and the product distribution, with particular attention to the Anderson–Schulz–Flory distribution (ASFD) and known deviations from this fundamental concept. Conventional FT catalysts, particularly Fe- and Co-based catalysis systems, are reviewed, highlighting their central role and the influence of water and water–gas shift (WGS) activity on their catalytic behavior. Various mechanisms of catalyst deactivation are also investigated, and the high methanation activity of Co-based catalysts is illustrated. To make this complex field accessible to a broader audience, we explain conjectured reaction mechanisms, namely, the carbide mechanism and CO insertion. We discuss the complex formation of a wide range of products, including olefins, kerosenes, branched hydrocarbons, and by-products such as alcohols and oxygenates. The article goes beyond the traditional scope of FT catalysis by addressing topics of current interest, including the direct hydrogenation of CO2 for power-to-X applications and the use of bifunctional catalysts to produce tailored FT products, most notably for the production of sustainable aviation fuel (SAF). This mini-review provides a holistic overview of the evolving landscape of FT catalysts and is aimed at both experienced researchers and those new to the field while covering current and emerging trends in this important area of energy research.

Production of Mannooligosaccharides from Açaí Seed by Immobilized β-Mannanase

In this work, an enzyme cocktail with β-mannanase as the main activity was immobilized on epoxy resin foams filled with fibers from annatto capsules. The catalytic system was characterized by SEM, FTIR, and a mechanical crush resistance test. The behavior of the pH and temperature for the hydrolysis of the locust bean gum were also studied. With the same substrate and with respect to the free enzyme, the immobilized enzyme showed an activity retention of 79.61%. Its operational stability in ten reuse cycles did not show any statistically significant loss of activity. This catalytic system was used to study the preferential release of MOS of two to five degrees of polymerization from mannan present in dried and ground açaí seeds, which were not subjected to any other pretreatment. Using an experimental response surface design, the predicted quadratic models for the M2–M5 MOS content were obtained and they fit well with the experimental data, predicting a production range between 0.435 and 20 g/L of MOS (M2–M5). In addition, the production reached about 12 g/L under the optimized conditions. These results indicate that the used foamed epoxy resin supports and immobilization methodology are suitable for catalyzing the hydrolysis of mannan from açaí seeds.

Turnover Number in Photoinduced Molecular Catalysis of Hydrogen Evolution: a Benchmarking for Catalysts?

Development of devices for production of H2 using light and a sustainable source of electrons may require the design of molecular systems combining a molecular catalyst and a photosensitizer. Evaluation of the efficiency of hydrogen production is commonly performed in homogeneous solution with a sacrificial electron donor and the report of the maximal turnover number vs catalyst ( ). This figure of merit is strongly dependent on deactivation pathways and does not by itself provide a benchmarking for catalysts. In particular, when the photosensitizer degradation is the primary source of limitation, a kinetic model, rationalizing literature data, shows that a decrease of the catalyst concentration leads to an increase of . It indicates that exceptionally high obtained at very low catalyst concentration shall not be considered as an indication of an exceptional catalytic system. We advocate for a systematic kinetic analysis in order to get a quantitative measure of the competitive pathways leading to values and to provide keys for performance improvement.

Cerium/sulfur co-doped spinel iron-cobalt oxide@carbon interconnected mesh networks as superior peroxymonosulfate activator for tetracycline degradation

Transition metal spinel oxides have potential applications in activating peroxymonosulfate (PMS) to generate reactive substances for degrading organics in polluted water. However, many catalytic materials have low efficiency, indicating the need for advancements in material design. In this study, we present the one-step fabrication of Ce, S-codoped spinel iron-cobalt oxide@carbon (Ce-FeCo2O4@SxC) with interconnected mesh networks for efficient PMS activation in degrading tetracycline hydrochloride (TCH). Among the Ce-FeCo2O4@SxC samples, Ce-FeCo2O4@S1.5C demonstrates the highest catalytic performance, achieving a TCH degradation efficiency of 97.2 % in 30 min. Moreover, the catalytic system also exhibits anti-interference abilities against various anions and shows universality in degrading organic pollutants. Characterization and experimental tests confirm the co-existence of radical (SO4•−, •OH and O2•−) and non-radical pathways (1O2 and direct electron transfer), with 1O2 identified as the primary reactive species. Three plausible pathways for TCH removal are proposed based on detected intermediate products. Toxicity evaluation reveals a significant reduction in the toxicity of the original TCH solution during the degradation process with the PMS activator. This study introduces a simple yet effective co-doping strategy to enhance the catalytic properties of spinel oxides for PMS activation in degrading organic contaminants in aquatic environments.

Nickel-Catalyzed Chemoselective Carbomagnesiation for Atroposelective Ring-Opening Difunctionalization.

There is a pressing need for methods that can connect enantioenriched organic compounds with readily accessible building blocks via asymmetric functionalization of unreactive chemical bonds in organic synthesis and medicinal chemistry. Herein, the asymmetric chemoselective cleavage of two unactivated C(Ar)-O bonds in the same molecule is disclosed for the first time through an unusual nickel-catalyzed carbomagnesiation. This reaction facilitates the evolution of a novel atroposelective ring-opening difunctionalization. Utilizing readily available dibenzo bicyclic substrates, diverse valuable axially chiral biaryls are furnished with high efficiencies. Synthetic elaborations showcase the application potential of this method. The features of this method include good atom-economy, multiple roles of the nucleophile, and a simple catalytic system that enables the precise magnesiation of an α-C(Ar)-O bond and arylation of a β-C(Ar)-O bond.