Short Carbon Fibers Research Articles

Electromagnetic shielding effectiveness of silver‐coated hollow glass microsphere‐graded short carbon fiber epoxy composite

AbstractThe present study is investigating the use of short carbon fiber (SCF) and silver‐coated hollow glass microsphere (Ag@HGM) reinforced epoxy light‐weight composites for electromagnetic interference (EMI) shielding applications in the X‐band frequency range (i.e., 8–12 GHz). The study found that Ag@HGM along with SCF significantly improved the dielectric properties of the composites and enhanced the EMI shielding effectiveness of 34.6 dB. Thermal analysis indicates that the sample shows a high rate of heat dissipation and good thermal conductivity. The dynamic mechanical analysis has indicated that the composite has improved storage modulus, glass transition temperature, and activation energy.Highlights SCF and Ag@HGM epoxy composite is fabricated for EMI shielding application. Two steps: etching and electroless coating of HGM are used for silver coating. The addition of Ag@HGM has enhanced total SE from 27.4 to 34.6 dB. EM wave gets scattered, experiences internal reflections view SCF and Ag@HGM. Additionally, enhancement of thermal and mechanical properties is observed.

Effects of energized treatment on electro trigger shape memory behavior

The shape memory polymers (SMPs) can be programmed to take temporary shapes and return to their original shape when subjected to external stimuli. Electrically triggered SMP has become an important branch of shape memory materials because of its advantages such as remote heating, fast response and local control. In this paper, a novel shape memory composite structure is prepared by using polylactic acid (PLA) as substrate and short carbon fiber (SCF) as conductive filler. The electrification treatment during the preparation process has a beneficial effect on the SCF arrangement. Compared with the sample without electrification treatment, the highest conductivity can be increased from 43.96 S/m to 66.67 S/m, and the performance is improved by 51.66 %. When the voltage is increased from 3 V to 8 V, the time to reach the glass transition temperature (Tg) is reduced by 62.22 %, and the shape memory recovery time is reduced by 53.68 %. The intelligent fixture based on the composite structure can realize the remote grasp of 3D printed balls with a diameter of 40 mm and a weight of 18.35 g under pressure, which fully proves the reliable electrically triggered shape memory performance of the composite structure and the great application potential in the field of robot gripper.

Tensile Behavior of Parts Manufactured Using a Material Extrusion Process from a Filament with Short Carbon Fibers and PET Matrix

One of the latest tendencies in research related to material extrusion based on additive manufacturing is to determine the mechanical characteristics of parts taking into consideration the most influential manufacturing parameters. The main research objective is to describe how the manufacturing parameters, part orientation, layer thickness and infill density influence the tensile behavior of specimens made from PET with 15% short carbon fibers. The most advantageous result is obtained for a layer thickness of 0.15 mm, with 100% material infill, and material deposition on the longitudinal direction of the part. The obtained mean values are: 65.4 MPa tensile strength, 1.93% strain at rupture, and 9 GPa Young Modulus. For these values, the tensile behavior of specimens manufactured along transverse and thickness directions are presented. The least favorable results are obtained for manufacturing by thickness. The novelty of the discussed research consists in all these aspects together with an original mathematical model that was determined based on design of experiments with a correlation of the regression model of over 90%. By optical and electronic microscopy material gaps are visible in the filament and manufactured parts, and the failure occurs in most cases in form of matrix cracks and delamination.

Synergistic toughening modification and finite element analysis of carbon fiber/epoxy resin‐reinforced composites

AbstractIn this work, the poor fracture toughness of carbon fiber‐reinforced composites (CFRPs) was improved by the introduction of a graphene oxide/nanosilica (GOS) hybrid, and short carbon fibers (SCFs) were investigated through experimental and modeling methods. The effects of the SCF content, number of SCF layers, and introduction position on the mode I fracture toughness (GIC) and mode II fracture toughness (GIIC) of the composites were considered for epoxy resin (EP) modified by GOS. The results showed that GOS and SCF exhibited a synergistic toughening effect on CFRP. The GIC and GIIC of CFRP laminate with GOS content of 0.2 wt% and SCF content of 0.4 wt% reached 0.506 and 2.15 kJ/m2, increased by 72.2% and 53.6% compared to the unmodified composite, respectively. The number of layers and the lamination mode of GC10S5‐B specimens exhibited the optimal improvement of interlaminar fracture toughness. Similarly compared with those of the original. The GIC and GIIC of the CFRP laminates reached 0.662 and 0.506 kJ/m2 (enhanced by 125.9% and 95%, respectively). In addition, the stress propagation path and distribution, and progressive damage of the CFRP composites were obtained to further reveal the toughness mechanism.Highlights Synergistic toughening of resin modification and short carbon fiber on modes I and II fracture toughness of composites were considered. Content of short carbon fiber and lay‐up methods on toughness performance were investigated thoroughly. Finite element models were established to reveal the stress progress and distribution and toughness mechanism.

Carbon Fiber Composites Recycling Technology Enabled by the TuFF Technology

Carbon Fiber Composites (CFCs) recycling has received increasing interest by the composites industry, but it is still in its early stages as an industry. There are two primary challenges that need to be addressed in order to achieve full property retention during CFC recycling: (1) the ability to recover the fiber content without property loss; and (2) conversion of the recycled, short fiber material back into high-performance CFC structures. The ability to manufacture high fiber volume fraction CFCs with end-of-life products would provide an opportunity to reduce material cost and lifetime-embodied energy. In this paper, recycled, short carbon fibers are processed via solvolysis and converted into high-performance CFCs with fiber volume fraction of ~50% and excellent composite property retention. This is enabled through alignment of the discontinuous, recycled fiber feedstock using the Tailorable universal Feedstock for Forming (TuFF) process. The paper introduces the necessary steps to process the fibers in the wet-laid process and explores the resulting mechanical and microstructural properties. The importance of incoming fiber surface quality and the effect of surface contamination from residue left by the recycling process on both the TuFF process and final composite properties is discussed in detail. A pyrolytic process has been adopted to remove the residue that is a by-product of the recycling process from the incoming recycled fiber surface. The approach presents a promising pathway for the recycling of high-performance CFCs.

Processing and Analysis of Hybrid Fiber-Reinforced Polyamide Composite Structures Made by Fused Granular Fabrication and Automated Tape Laying

Fused granular fabrication (FGF) is a large format additive manufacturing (LFAM) technology and focuses on cost-effective granulate-based manufacturing by eliminating the need for semifinished filaments. This allows a faster production time and a broader range of usable materials for tailored composites. In this study, the mechanical and morphological properties of FGF test structures made of polyamid 6 reinforced with 40% of short carbon fibers were investigated. For this purpose, FGF test structures with three different parameter settings were produced. The FGF printed structures show generally significant anisotropic mechanical characteristics, caused by the layer-by-layer building process. To enhance the mechanical properties and reduce the anisotropic behavior of FGF structures, continuous unidirectional fiber-reinforced tapes (UD tapes), employing automated tape laying (ATL), were subsequently applied. Thus, a significant improvement in the flexural stiffness and strength of the manufactured FGF structures was observed by hybridization with 60% glass fiber-reinforced polyamide 6 UD tapes. Since the effectiveness of UD-tape reinforcement depends mainly on the quality of the bond between the UD tape and the FGF structure, the surface quality of the FGF structure, the interface morphology, and the tape-laying process parameters were investigated.

Improving resistance–strain effects of conductive polymer composites modified by multiscale fillers: Short carbon fiber and carbon nanotube

AbstractConductive polymer composites (CPCs) have attracted much attention in strain sensing applications due to their excellent conductivities and high sensitivities. However, research on simultaneous modification of CPCs with multiple conductive fillers is lacking. This study aims to systematically investigate the electrical conductivities and strain‐sensing properties of two filler‐modified epoxy resin (EP) composites with different scale additives—short carbon fibers (SCFs) and carbon nanotubes (CNTs)—obtained by mixing and curing to obtain the samples. Both the SCF/EP and SCF/CNT/EP composite resistivities decreased with increasing filler content, and 1.35 wt% was the percolation threshold for SCF/EP composites; during monotonic tensile loading, the resistance change ratio (ΔR/R0) of the CPCs increased with increasing strain, and the sensitivities decreased with increasing conductive filler content. The CPCs containing SCFs and CNTs exhibited stable and repeatable resistance responses during cyclic tensile loading, among which the SCF/CNT_1.5/0.3 composite was the most suitable for use as a sensing material with a sensitivity of 0.149. According to the conductivity and resistance–strain response mechanism analysis, the CNTs supplementing and refining the CPC conductive network composed of SCFs were considered the main reason for the resistance response linearization and excellent dynamic response repeatability. CPCs can be widely used in strain sensing and damage monitoring.Highlights Provided a strategy for multiscale conductive filler‐modified epoxy resins. Realized monotonicity of resistance–strain response by adding multiscale conductive fillers. Explored resistance‐strain effect under dynamic cycling loading. Identified optimal materials for damage detection. Analyzed the resistance–strain response mechanism of single and multiscale conductive filler‐modified CPCs.

Mechanical property and thermal stability of short carbon fiber reinforced polysulfonamide composites

AbstractIn this paper, polysulfonamide‐based composite materials (SCF/PSAf composite) reinforced by the short carbon fiber were prepared. The mechanical properties and thermal stability of SCF/PSAf composite were characterized experimentally and compared with those of polysulfonamide‐based single‐polymer composites (PSA SPCs). Results showed that SCF/PSAf composites exhibit higher thermal stability due to the excellent thermal stability of SCFs. Furthermore, the additional short carbon fibers also considerably enhance the flexure strength of PSA SPCs due to the strong interfacial bonding between SCF and PSAf. The properties and understanding of SCF/PSAf composite obtained in this work can benefit further applications of this novel composite material.Highlights SCF/PSAf composites are prepared by hot compression, and the adhesion between the PSA matrix and SCF is good. The flexural strength of the SCF/PSAf composite is about 2.5 times higher than that of PSA SPCs. The storage modulus of SCF/PSAf composites is about 3.5 times higher than that of PSA SPCs. The addition of short carbon fibers helps to improve the thermal properties of SCF/PSAf composites. SCF/PSAf composite has a stronger ability to resist deformation and a higher operating temperature than the PSA SPCs do.

Mouldable Conductive Plastic with Optimised Mechanical Properties.

This paper investigates making an injection mouldable conductive plastic formulation that aims for conductivity into the electromagnetic interference (EMI) shielding range, with good mechanical properties (i.e., stiffness, strength, and impact resistance). While conductivity in the range (electrostatic charge dissipation) and EMI shielding have been attained by incorporating conductive fillers such as carbon black, metals powders, and new materials, such as carbon nanotubes (CNTs), this often occurs with a drop in tensile strength, elongation-to-break resistance, and impact resistance. It is most often the case that the incorporation of high modulus fillers leads to an increase in modulus but a drop in strength and impact resistance. In this work, we have used short carbon fibres as the conductive filler and selected a 50/50 PBT/rPET (recycled PET) for the plastic matrix. Carbon fibres are cheaper than CNTs and graphenes. The PBT/rPET has low melt viscosity and crystallises sufficiently fast during injection moulding. To improve impact resistance, a styrene-ethylene-butadiene-styrene (SEBS) rubber toughening agent was added to the plastic. The PBT/rPET had very low-impact resistance and the SEBS provided rubber toughening to it; however, the rubber caused a drop in the tensile modulus and strength. The short carbon fibre restored the modulus and strength, which reached higher value than the PBT/rPET while providing the conductivity. Scanning electron microscope pictures showed quite good bonding of the current filler (CF) to the PBT/rPET. An injection mouldable conductive plastic with high conductivity and raised modulus, strength, and impact resistance could be made.

Fabrication and mechanical properties of TiC coated short carbon fiber reinforced Ti5Si3–TiC composites

Ti5Si3-based composites reinforced with TiC-coated Cf and TiC particulate (TiC@Cf/Ti5Si3–TiC) were fabricated by spark plasma sintering. The performance of the TiC@Cf/Ti5Si3–TiC composite was comprehensively evaluated by investigating its mechanical properties at room temperature, as well as the thermal shock resistance, oxidation resistance and flexural strength at high temperatures. By employing optimal process parameters obtained through response surface methodology, the TiC@Cf/Ti5Si3–TiC composite exhibited a maximum room-temperature fracture toughness of 9.32 ± 1.05 MPa m1/2, which represented a significant increase of 261.2% and 23.1% compared to monolithic Ti5Si3 and TiC@Cf/Ti5Si3 composite, respectively. The flexural strength of the TiC@Cf/Ti5Si3–TiC composite measured at room temperature, 1000 °C, and after quenching from 1200 °C was 531 ± 61 MPa, 299 ± 43 MPa, and 138.4 ± 15 MPa, achieving an improvement of 221.8%, 128.2%, and 295.4% compared to monolithic Ti5Si3. The incorporation of TiC particulates appeared to mitigate the fiber-matrix interfacial reaction more effectively than that observed in the TiC@Cf/Ti5Si3 composite previously investigated. Consequently, the reinforcing mechanism of fiber pulling-out and debonding, crack blocking, deflection, and bridging was fully operational at heightened sintering temperatures. These essential factors play a vital role in remarkably enhancing the mechanical properties of the TiC@Cf/Ti5Si3–TiC composite.

Erimiş Filament Üretim Yöntemi ile Üretilen Kompozit Yapılarda Yöne Bağlı Yüzey Özelliklerinin İncelenmesi ve İyileştirilmesi

Additive manufacturing methods, which have begun to be used in final product production beyond producing prototypes, are popular research topics today. The Fused Filament Fabrication (FFF) method, which has a wider usage area and user base, is the most well-known among these methods. The method in which the polymer is extruded in layers has advantages such as design freedom and topology optimization, as well as disadvantages such as surface roughness and low production speed. The number of materials that can be used in the FFF method is diversifying day by day, and polymeric composites can also be produced beyond pure polymers. The use of engineering polymers such as polyamide in this production method creates many new opportunities. In addition, the start of production of short fiber reinforced polymeric composites has paved the way to produce high-performance final products. In this study, the effects of parameters such as layer thickness and printing orientation on the surface roughness of samples produced using polyamide and short carbon fiber reinforced polymer matrix composite materials were examined. Chemical surface treatment was applied to the surfaces of 3D-printed samples to improve surface roughness. It was concluded that the increase in layer thickness increases the surface roughness, the -/+45 filling orientation creates higher roughness than the 0 and 90 orientations, and the surface quality can be increased by chemical surface modification.

Microstructure evolution and ablation mechanisms of Csf/ZrB2-SiC composites at different heat fluxes under air plasma flame

In this study, short carbon fibre (Csf) reinforced ZrB2-SiC composites were fabricated via direct ink writing followed by precursor infiltration and pyrolysis. The ablation behaviour of the composites was investigated at heat fluxes of 4–6 MW/m2 under an air plasma flame, which revealed excellent ablation resistance with negative linear ablation rates of − 0.1 to − 0.5 µm/s. The results showed that ZrO2-SiO2 oxide layer was formed on the ablation surface after ablation, which provided effective protection to the internal materials. With an increase in heat flux, ZrO2 precipitated from the SiO2 melt first in the form of nano-tetragonal ZrO2 (t-ZrO2), owing to the vaporisation of SiO2. During cooling, the nano t-ZrO2 particles were retained, and some of them reacted with SiO2 to form ZrSiO4, thus improving the thermal stability of the SiO2-ZrO2 oxide layer. In contrast, t-ZrO2 agglomerated and grew owing to capillary force and finally transformed into monoclinic ZrO2 (m-ZrO2). Moreover, a higher heat flux led to the size of precipitation ZrO2 increases, meanwhile increasing the content of t-ZrO2 and ZrSiO4 in the oxide layer.

Multiscale numerical modeling of large-format additive manufacturing processes using carbon fiber reinforced polymer for digital twin applications

Large Format Additive Manufacturing (LFAM) has gained prominence in the aerospace and automotive industries, where topology optimization has become crucial. LFAM facilitates the layer-by-layer production of sizeable industrial components in carbon fiber (CF) reinforced polymers, however 3D printing at large scales results in warpage generation. Printed components are deformed as residual stresses generated due to thermal gradients between adjacent layers. This paper tackles the problem at two different scales: the micro and macroscale. Initially, the microstructure characterization of the thermoplastic ABS matrix composite material enriched with 20% short CF is used in the development of numerical models to understand the mechanical behavior of the studied material. Numerical modeling is performed simultaneously by means of Mean-Field (MF) homogenization methods and Finite Element Analysis (FEA). Outcomes validated with corrected experimental mechanical testing results show a discrepancy in the elastic modulus of 7.8% with respect to FE multi-layer analysis. Micro-level results are coupled with the a macroscopic approach to reproduce the LFAM process, demonstrating the feasibility of the tool in the development of a Digital Twin (DT).

Mechanical, electrical and self-healing properties of carbon fibre-reinforced ultra-lightweight ECC

The hybrid mixes of carbon fibres (CF), fly ash cenosphere and polyethylene fibre could be used to develop smart ultra-lightweight engineered cementitious composites (ULW-ECCs). In this study, the effects of CF length (1, 3, 6, 9, 12, 15, 20 mm) with different volume fractions (0.0, 0.5 and 1.0 vol%) on the fundamental mechanical (compression, tension and flexure) and electrical properties of CF-reinforced ULW-ECCs were evaluated. Pseudo-strain-hardening indices, multiple micro-cracking behaviours and self-healing properties were also tested. The experimental results reveal that, except for the 1 mm particle CF, incorporating CF could improve the strength (compression, tension and flexure) of ULW-ECCs but decrease the strain ductility properties under tension; and CF lengths of 9- and 12-mm show better results. The electrical conductivity of ULW-ECCs was improved by CF, and the higher dosage further increased the conductivity. The conductivity increased first and then decreased with the increase in CF length and the 9 mm CF (1.0 vol%) shows higher conductivity. The conductive network was affected by the volume fraction, length, count under the same content, and possible fracture of CF. Long CFs work well at low content in forming conductive networks, while short CFs are more effective at high content. The conductivity decreased with the increase of curing age and reached a constant value after 90 d. Incorporating CF and increasing its length/content negatively impacted crack number and width. CF-reinforced ULW-ECCs exhibit excellent self-healing, with reduced ability as wet-dry cycles and curing age increase.

Wide-range soft anisotropic thermistor with a direct wireless radio frequency interface

Temperature sensors are one of the most fundamental sensors and are found in industrial, environmental, and biomedical applications. The traditional approach of reading the resistive response of Positive Temperature Coefficient thermistors at DC hindered their adoption as wide-range temperature sensors. Here, we present a large-area thermistor, based on a flexible and stretchable short carbon fibre incorporated Polydimethylsiloxane composite, enabled by a radio frequency sensing interface. The radio frequency readout overcomes the decades-old sensing range limit of thermistors. The composite exhibits a resistance sensitivity over 1000 °C−1, while maintaining stability against bending (20,000 cycles) and stretching (1000 cycles). Leveraging its large-area processing, the anisotropic composite is used as a substrate for sub-6 GHz radio frequency components, where the thermistor-based microwave resonators achieve a wide temperature sensing range (30 to 205 °C) compared to reported flexible temperature sensors, and high sensitivity (3.2 MHz/°C) compared to radio frequency temperature sensors. Wireless sensing is demonstrated using a microstrip patch antenna based on a thermistor substrate, and a battery-less radio frequency identification tag. This radio frequency-based sensor readout technique could enable functional materials to be directly integrated in wireless sensing applications.

Integrated computational modeling of large format additive manufacturing: Developing a digital twin for material extrusion with carbon fiber-reinforced acrylonitrile butadiene styrene

Material extrusion (MEX) continues to be a pivotal additive manufacturing (AM) process, involving the selective heating and layer-by-layer deposition of material. However, conventional finite-element models (finite-element analysis) face limitations in accurately simulating the MEX process, highlighting the need for experimental validation. This paper highlights an advanced material modeling technology that streamlines the development of composite parts using large format AM (LFAM). It specifically focuses on a thermoplastic acrylonitrile butadiene styrene (ABS) matrix composite material enriched with 20% short carbon fibers. The study employs integrated computational materials engineering, integrating (i) the manufacturing process, (ii) the material’s microstructure, (iii) homogenization techniques, and (iv) the performance of the final part. The development of a digital twin for pellet extrusion is proposed, emphasizing the importance of micro-structure characterization to account for warpage and residual stresses that lead to part distortion. The demonstrator manufactured for this study is a wind turbine mold of a blade section. Experimental tests revealed an elastic modulus of 5.5 GPa and a hardening modulus of 2.4 GPa for the composite. The numerical microscopic model showed a 16% error in the elastic modulus compared to experimental results. The study concludes that the homogenization techniques are effective in predicting the elastic properties but lack accuracy in the plastic region. The application of the model to the LFAM process of pellet extrusion is demonstrated, with simulation results showing a maximum deformation close to the center of the wind turbine blade mold.

Collaborative enhancement of thermal diffusivities and mechanical properties of Csf-Cu/Mg composites via introducing Cu coating with different thicknesses

Mg alloy matrix composites reinforced with short carbon fibers (Csf/Mg) are considered as potential candidates for integrated structural-functional electronic parts that satisfy the requirements of lightweight, excellent mechanical properties, and heat dissipation. However, the different characteristics of Csf and Mg alloy make the interface a critical issue affecting the synergistic improvement of thermal and mechanical properties of the composites. Here, Cu coating with different thicknesses is introduced to modify the Csf/Mg interface, so as to simultaneously enhance the thermal and mechanical performances, which can combine the advantages of coating modification and matrix alloying. Results reveal that thermal diffusivity (TD) of 3-Csf-Cu/Mg composites is as high as 22.12 mm2/s and an enhancement of 52.97% is achieved compared with Csf/Mg composites, as well as 16.3% enhancement of ultimate compressive strength (UCS) in the longitudinal direction, 8.84% improvement of UCS in the transverse direction, and 53.08% increasement of ultimate tensile strength (UTS). Such improvement can be ascribed to the formation of intermetallic compounds. The formation of intermetallic compounds can not only effectively alleviate the lattice distortion of the matrix and decrease interfacial thermal resistance, but also bear the loads. Our work is of great significance for designing Csf/Mg composites with integrated structure and function.

Microwave-assisted ZnO-decorated carbon urchin resembling 'shish-kebab' morphology with self-healing and enhanced electromagnetic shielding properties.

Herein, inspired by Acacia auriculiformis fruit, the shish-kebab-like growth of ZnO on carbon urchin (ZnO@CU) was designed using microwave radiation, thus leading to a hierarchal 3D structure that can promote multiple internal reflections through polarization centers. This hierarchal structure was then dispersed in a designer polyetherimide (PEI) matrix containing dynamic covalent bonds that can undergo metathesis, triggered by temperature, to harness self-healing properties in the composite. Such key attributes are required for their potential use in EMI shielding applications where frequent repairs are indispensable. Morphological investigation revealed that the ZnO flower was periodically nucleated like 'shish-kebab' structures on CU surfaces. CU was designed from short carbon fibers using a facile modified method. The EMI shielding performance of the resulting composites was investigated in the X-band, illustrating a shielding effectiveness of -40.6 dB for 2 wt% of ZnO@CU loading, and the composite can be preserved after the self-healing procedure. The ZnO 'kebabs' on 'CU shish' facilitated multiple scattering and numerous polarization centers to improve the EMI shielding performances at extremely low filler contents. In addition, the mechanical and thermal properties of the composite showed improved structural integrity and superior resistance to extreme temperatures, respectively. Overall, the proposed ZnO@CU/PEI composite has great potential to fulfill the increasing demands for lightweight EMI shielding materials in many fields.

Effect of ceramic particles on the mechanical and tribological properties of short carbon fibre reinforced epoxy composites

Effect of ceramic particles on the mechanical and tribological properties of short carbon fibre reinforced epoxy composites

Reliability assessment of carbon fiber mortar: Combined pulse velocity, point load, and compressive strength tests

Cement mortar is used as an adhesive and plaster for brick walls, drainage channels or irrigation with river stones or mountain stones, and in the manufacturing of short revetments. The performance of cement mortar requires continuous improvement by construction materials researchers, scientists, and building contractors. Recently, carbon fiber sheet has gained popularity for use in retrofitting and improvement to the performance of building elements. This study aims to recycle small sheets of unused carbon fiber by cutting them into short carbon fiber (SCF) with a uniform length of 12 mm, which is used as an internal reinforcement in the cement mortar. All plain and fibrous mortar were prepared with a 50 mm cube mold. In addition, tests were conducted to provide reliable data regarding the application of recycled carbon fiber sheets as discrete fiber reinforcement in the improvement of cement mortar; these include ultrasonic pulse velocity (UPV), compressive strength, and point load strength index (PLSI) (known for performance rock testing in geotechnical and geological environments) tests. The test results for UPV, PLSI, and compressive strength showed that the addition of carbon fiber improves the performance of the mortar when compared to plain mortar. Furthermore, two simplified relationships are made: the first correlation was for PLSI with compressive strength, and the second correlation was for UPV with compressive strength. Finally, these correlations were compared with those of experimental tests obtained from published literature, thus demonstrating the correctness of the PLSI, compressive strength, and UPV values obtained in this study.