Carbon-based Perovskite Solar Cells Research Articles

Superwetting Nanofluids of NiOx-Nanocrystals/CsBr Solution for Fabricating Quality NiOx-CsPbBr3 Gradient Hybrid Film in Carbon-Based Perovskite Solar Cells.

The wettability of precursor solution on substrates is the critical factor for fabricating quality film. In this work, superwetting nanofluids (NFs) of non-stoichiometric nickel oxide (NiOx) nanocrystals (NCs)-CsBr solution are first utilized to fabricate quality NiOx-CsPbBr3 hybrid film with gradient-distributed NiOx NCs in the upper part for constructing hole transport ladder in carbon-based perovskite solar cells (C-PSCs). As anticipated, the crystalline properties (improved crystalline grain diameters and reduced impurity phase) and hole extraction/transport of the NiOx-CsPbBr3 hybrid film are improved after incorporating NiOx NCs into CsPbBr3. This originates from the superb wettability of NiOx-CsBr NFs on substrates and the excellent hole-transport properties of NiOx. Consequently, the C-PSCs with the structure of FTO/SnO2/NiOx-CsPbBr3/C displays a power conversion efficiency of 10.07%, resulting in a 23.6% improvement as compared with the pristine CsPbBr3 cell. This work opens up a promising strategy to improve the absorber layer in PSCs by incorporating NCs into perovskite layers through the use of the superwettability of NFs and by composition gradient engineering.

Work Function Tuning of Carbon Electrode to Boost the Charge Extraction in Hole Transport Layer-Free Perovskite Solar Cells.

Perovskite solar cell (PSC) is a promising photovoltaic technology that achieves over 26% power conversion efficiency (PCE). However, the high materials costs, complicated fabrication process, as well as poor long-term stability, are stumbling blocks for the commercialization of the PSCs in normal structures. The hole transport layer (HTL)-free carbon-based PSCs (C-PSCs) are expected to overcome these challenges. However, C-PSCs have suffered from relatively low PCE due to severe energy loss at the perovskite/carbon interface. Herein, the study proposes to boost the hole extraction capability of carbon electrode by incorporating functional manganese (II III) oxide (Mn3O4). It is found that the work function (WF)of the carbon electrode can be finely tuned with different amounts of Mn3O4 addition, thus the interfacial charge transfer efficiency can be maximized. Besides, the mechanical properties of carbon electrode can also be strengthened. Finally, a PCE of 19.03% is achieved. Moreover, the device retains 90% of its initial PCE after 2000 h of storage. This study offers a feasible strategy for fabricating efficient paintable HTL-free C-PSCs.

Dual-sites passivation for efficient and stable carbon-based perovskite solar cells

It has been proven that dual-active-site passivation is more effective than single-site passivation in mitigating surface defects of carbon-based perovskite solar cells (C-PSCs). Therefore, it is imperative to explore new agents capable of inducing dual-active-site passivation effect. This work strategically employs potassium laurate (KLA) as a surface passivating agent, which stands out due to its extended saturated alkane chains and carboxylate groups, offering dual-active sites encompassing carboxylate ions and K+ cations. Carboxylate ions play a pivotal role in passivating low-coordinated Pb2+ defects, while K+ metal cations are anticipated to address anionic defects. The champion C-PSC achieves an impressive power conversion efficiency (PCE) of 16.10%, increased from 14.35% of the original. The incorporation of KLA serves to diminish surface defects within the film and suppress non-radiative recombination at the interface by dual-sites passivation, thereby establishing itself as a valuable technique for enhancing the efficiency and durability of C-PSCs.

Enhanced photoelectric performance of dual cations quantum dots carbon-based perovskite solar cells with stacked structure

Enhanced photoelectric performance of dual cations quantum dots carbon-based perovskite solar cells with stacked structure

Design tungsten oxides hole transport layers (HTLs) to modify the back interface in all-inorganic carbon-based CsPbBr3 solar cells

To enhance the inferior photovoltaic performance of all-inorganic carbon-based perovskite solar cells (C-PSCs) caused by inefficient charge extraction and transport processes of the CsPbBr3/carbon back interface, three types of tungsten oxides (WO3, WO2.72, WO2) are synthesized as low cost and stable hole transport layers (HTLs) to modify the back interface by tunning the energy level alignment. Among the three kinds of tungsten oxides, WO3 shows the best hole extraction and transport capability and the C-PSCs using WO3 HTL generates a power conversion efficiency (PCE) of 7.90% with a high open circuit voltage (Voc) of 1.307 V, indicating a great PCE enhancement of 43.9%, as compared with the device without HTL (5.49%). Meanwhile, WO2.72 and WO2 also are also proved to be qualified HTLs and the devices show PCE values of 7.57% and 6.24%, respectively. Importantly, WO3 and WO2.72 based device show excellent stabilities with PCE retention over 90% of the initial PCE values under ambient conditions for 60 days.

Perovskite/La-BDC heterojunction enhances the performance of carbon-based perovskite solar cells

Carbon-based Perovskite Solar Cells (C-PSCs) present a promising avenue for enhancing the stability and commercialization of PSCs. However, the power conversion efficiency (PCE) of C-PSCs still lags behind that of metal-based PSCs. In this study, La-BDC (La-MOF prepared by La3+ and ligand H2BDC) has successfully synthesized using a simple hydrothermal method and then directly introduced into CH3NH3PbI3 (MAPbI3) perovskite precursor solution to prepare perovskite/La-BDC heterojunction structure with remarkable properties in light absorption, hydrophobicity, and crystallinity. By incorporating this structure, the PCE of C-PSCs with an FTO/SnO2/MAPbI3/La-BDC/Carbon architecture was effectively enhanced. The presence of CO functional group in La-BDC effectively reduced interface defects while improving carrier separation efficiency, and successfully passivated the free Pb2+ ions within the perovskite. Remarkably, the La-BDC-based device achieved a superior PCE of 14.95%, surpassing the pristine device's PCE by an impressive margin of 20.37%. Moreover, even after a 31 days period of air storage (temperature range of 15–25℃, humidity range of 15–30%), the La-BDC-based devices maintained over 90% of the initial performance, demonstrating excellent stability. This study provides a facile and effective strategy for improving the PCE and stability of C-PSCs through implementing a La-BDC heterojunction structure， and provides a new idea for MOF materials in the field of PSCs.

Efficient and Stable CuSCN-based Perovskite Solar Cells Achieved by Interfacial Engineering with Amidinothiourea.

Cuprous thiocyanate (CuSCN) emerges as a prime candidate among inorganic hole-transport materials, particularly suitable for the fabrication of perovskite solar cells. Nonetheless, there is an Ohmic contact degradation between the perovskite and CuSCN layers. This is induced by polar solvents and undesired purities, which reduce device efficiency and operational stability. In this work, we introduce amidinothiourea (ASU) as an intermediate layer between perovskites and CuSCN to overcome the above obstacles. The characterization results confirm that ASU-modified perovskites have eliminated trap-induced defects by strong chemical bonding between -NH- and C═S from ASU and under-coordinated ions in perovskites. The interfacial engineering based on the ASU also reduces the potential barrier between the perovskite and CuSCN layers. The ASU-treated perovskite solar cells (PSC) with a gold electrode obtains an improved power conversion efficiency (PCE) from 16.36 to 18.03%. Furthermore, after being stored for 1800 h in ambient air (relative humidity (RH) = 45%), the related device without encapsulation maintains over 90% of its initial efficiency. The further combination of ASU and carbon-tape electrodes demonstrates its potential to fabricate low-cost but stable carbon-based PSCs. This work finds a universal approach for the fabrication of efficient and stable PSCs with different device structures.

The surface effect of chlorinated mesoscopic TiO2 in printable carbon-based perovskite solar cells

Printable HTM-free (HTM = hole-transporting material) mesoporous carbon-based perovskite solar cells (C-PSCs) are one of the most promising technologies. In this study, a high-quality chlorinated mesoscopic TiO2 (m-TiO2) film was obtained by hydrochloric acid (HCl) wet chemical process and applied in C-PSCs based on TiO2/ZrO2/(5-AVA)x(MA)1-xPbI3/C structures. Experimental results show that the PCE of chlorinated m-TiO2 C-PSCs greatly improved. Based on (5-AVA)x(MA)1-xPbI3, C-PSCs with TiO2 ETL treated with HCl aqueous solution achieved an average photovoltaic conversion efficiency of 9.36 %, which is an increase of 7.96 % in comparison with the efficiency of the device using unmodified TiO2 ETL, while the Voc and the Jsc were increased by 3.63 % and 2.63 %, respectively. In a 30-day aging test, C-PSCs based on (5-AVA)x(MA)1-xPbI3 and TiO2-HCl 1 exhibited excellent stability under ambient air conditions.

Enhancing Efficiency and Stability in Carbon-Based Perovskite Solar Cells by Double Passivation with Ultralow-Cost Coal-Derived Graphene and Its Derivatives.

Coal-derived carbon nanomaterials possess numerous superior features compared to other classic carbon, such as readily accessible surfaces, tunable pore structure, and facile and precise surface functionalization. Therefore, the controllable preparation of coal-derived carbon nanomaterials is anticipated to be of great significance for the performance improvement and commercialization process of carbon-based perovskite solar cells (C-PSCs). In this study, we successfully synthesized highly stable and commercially valuable graphene oxide (GO) and reduced graphene oxide (rGO) utilizing coal. Compared to traditional methods and commercial graphene, the chemical oxidation and pyrolysis process used in this study is mild and simple, offering the advantages of controlled composition and the absence of other impurities. GO or rGO was incorporated into the top of the SnO2 electron transport layer (ETL) of C-PSCs. Under optimized conditions and ultraviolet-ozone (UVO) irradiation, the ultimate power conversion efficiency (PCE) increased from the unmodified 12.4 to 14.04% (based on rGO) and 15.18% (based on GO), representing improvements of 22 and 31%, respectively. The improved photovoltaic performance is mainly owing to enhanced charge transport capabilities, denser interfacial contacts, improved carrier separation properties, increased conductivity, and abundance of hydrophilic functional groups in GO, which can form more stable hydrogen bonds with SnO2. After being stored at room temperature and ambient humidity for 30 days, the modified, unpacked devices retained 87% of the highest power conversion efficiency (PCE). This study introduces a practical and manageable method to enhance the performance of C-PSCs by using functional carbon nanomaterials derived from coal.

Enhancing the Performance of the Mesoporous TiO2 Film in Printed Perovskite Photovoltaics through High‐Speed Imaging and Ink Rheology Techniques

AbstractMesoscopic carbon‐based perovskite solar cells (C‐PSCs) have the potential to be manufactured at an industrial scale by utilizing screen‐printing, a simple, affordable, and commercially mature process. As such, many recent publications have focused on enhancing performance through modifying cell architecture and perovskite chemistries. This work examines how ink rheology can be tuned to optimize cell performance through reducing the occurrence of common print defects to create higher quality m‐TiO2 films. Inks with different solvent dilutions and rheological profiles are assessed using high‐speed imaging through the screen‐printing visualization (SPV) technique, to investigate the impact of the viscosity and elasticity on ink separation mechanisms. The resultant film quality and its influence on device performances are then assessed. Ink separation lengths are minimized, and the formation of filaments ceases during printing, leading to improved TiO2 film topography and homogenous infiltration of the perovskite precursor. Consequently, PCE is improved by over 10% of the original efficiency in cells and 224 cm2 active area modules due to enhanced Voc and FF. These results not only provide key insights into tailoring ink rheology, to achieve improved print homogeneity and higher performing cells, but also aid further work on enhancing the performance of other screen‐printed functional films.

Crystallization modulation and defect passivation in carbon-based perovskite solar cells using multifunctional group additive

Recently, carbon-based perovskite solar cells have attracted wide attention in academia and industry because of their simple preparation process, low cost, and adaptability to roll-to-roll industrial production. The combination of ternary perovskite composition and carbon electrode configuration is expected to meet the requirements of device performance and stability. However, low grain size, and high density of grain boundary and surface defect states result in serious non-radiative recombination, which is one of the main gaps between the carbon-based perovskite solar cells and metal-electrode-based devices. Based on the consideration of crystal tuning and defect passivation of ternary CsFAMA thin films, the additive molecule 5-(Difluoromethoxy)-2-mercapto-1H-benzimidazole (DMB) with multifunctional groups were introduced into the film. XRD show that the (100) and (200) crystal plane orientation growth directed by the DMB additive lead to the formation of the micro-sized perovskite. XPS suggests that DMB not only modulates the crystallization of the films but also exists at the grain boundaries, and realizes the passivation of undercoordinated Pb2+ defects and inhibits the generation of Pb0. The defect state density is significantly reduced, and the carrier lifetime is greatly improved. The possible mechanism for perovskite crystal growth as well as defect passivation based on Lewis acid-base coordination and hydrogen bond was also proposed. After the introduction of DMB, a power conversion efficiency of 14.40% was achieved, which was 13.4% higher than that of the control device. After nearly 1200 h of environmental stability test, the DMB modified device still retained 95% of the original efficiency. This work emphasizes the feasibility of simultaneously realizing the crystallization modulation and defect passivation of carbon-based perovskite solar cells using the additive with multifunctional groups, and provides a reference for the commercialization of carbon-based perovskite solar cells.

Optimizing Carbon-Based Perovskite Solar Cells with Pyramidal Core–Shell Nanoparticles for High Efficiency

Optimizing Carbon-Based Perovskite Solar Cells with Pyramidal Core–Shell Nanoparticles for High Efficiency

2-Iodoaniline-Modified High-Efficiency Carbon-Based CsPbIBr2 perovskite solar cells

The stability of carbon-based perovskite solar cells without a hole transport layer is better than that of hybrid perovskite solar cells, However, there will be serious interface recombination and carrier transport inhibition at the perovskite/carbon interface. Therefore, the interface between CsPbIBr2 perovskite and carbon electrodes was modified with 2-iodoaniline (2-IDA) to facilitate hole extraction in solar cell devices. –NH2 has a lone pair of electrons that can be coordinated with positively charged Lewis acid defects via coordination bonds. In addition, the introduction of iodide ions can compensate the halide vacancy on the grain boundary, inhibit the production of non-radiative recombination and passivate the defects in the film. After modification, the open-circuit voltage decays more slowly and the carrier lifetime is longer, resulting in a photoelectric conversion efficiency of 10.23% and Improve the moisture stability of the device.

Two birds with one stone: SmCl3 modified TiO2/perovskite interface to enhance the performance of carbon-based perovskite solar cell

Two birds with one stone: SmCl3 modified TiO2/perovskite interface to enhance the performance of carbon-based perovskite solar cell

Interface modification for efficient carbon-electrode CsPbI2Br perovskite solar cells using ionic liquid.

All-inorganic CsPbI2Br, as a promising photovoltaic (PV) material, have attracted extensive research attention in society for its outstanding thermal stability and appropriate trade-offs. Carbon-based perovskite solar cells (C-PSCs) without hole transporting layer (HTL) have shown great potential in terms of cost-effectiveness and stability. However, the inevitable defects on the surface of CsPbI2Br films severely hampers the development of high-efficiency CsPbI2Br C-PSCs. Surface engineering has emerged an effective approach to overcome this challenge. Herein, 1-decyl-3-methylimidazolium tetrafluoroborate (DMTT) ionic liquid was introduced between CsPbI2Br and carbon electrode to reduce non-recombination of charges, decrease defect states, minimize the energy-level mismatch, and greatly enhance the device stability. As a result, the HTL-free CsPbI2Br C-PSCs combined with DMTT as an interface modification achieved a higher power conversion efficiency (PCE) of 12.47% than that of the control devices with a PCE of 11.32%. Furthermore, without any encapsulation, the DMTT-optimized C-PSC remained approximately 84% of its initial PCE after over 700 h under room temperature and 25% relative humidity (RH) conditions. Additionally, when exposed to a temperature of 65 °C for over 400 h, the device still retained 74% of the initial PCE, demonstrating its thermal stability.

Quantifying Infiltration for Quality Control in Printed Mesoscopic Perovskite Solar Cells: A Microscopic Perspective.

Mesoscopic carbon-based perovskite solar cells (CPSCs) are often cited as a potential frontrunner to perovskite commercialization. Infiltration, the extent to which perovskite fills the mesoporous scaffold, is critical for optimum performance and stability. However, infiltration data are usually presented as qualitative photographic comparisons of samples with extreme infiltration variation. This work examines how small infiltration defects impact performance using an optical microscopy examination of the base TiO2 layer to identify issues and develop targeted techniques for infiltration enhancement. Critically, the uninfiltrated area at the base of the stack was found to correlate well with PCE across multiple batches of varied print quality and ZrO2 thickness. Through reduction of mesh mark defects and improvement of print quality in the ZrO2 and carbon layers, a champion PCE of 15.01% is attained. It follows that this facile, multiscaled, nondestructive technique could enable targeted performance enhancement and quality control in future scale-up initiatives.

Ligand-Induced In Situ Epitaxial Growth of PbI2 Nanosheets/MAPbI3 Heterojunction Realizes High-Performance HTM-Free Carbon-Based MAPbI3 Solar Cells.

Hole-transporting layer-free carbon-based perovskite solar cells (HTL-free C-PSCs) hold great promise for photovoltaic applications due to their low cost and outstanding stability. However, the low power conversion efficiency (PCE) of HTL-free C-PSCs mainly results from grain boundaries (GBs). Here, epitaxial growth is proposed to rationally design a hybrid nanostructure of PbI2 nanosheets/perovskite with the desired photovoltaic properties. A post-treatment technique using tri(2,2,2-trifluoromethyl) phosphate (TFEP) to induce in situ epitaxial growth of PbI2 nanosheets at the GBs of perovskite films realizes high-performance HTL-free C-PSCs. The structure model and high-resolution transmission electron microscope unravel the epitaxial growth mechanism. The epitaxial growth of oriented PbI2 nanosheets generates the PbI2 /perovskite heterojunction, which not only passivates defects but forms type-I band alignment, avoiding carrier loss. Additionally, Fourier-transform infrared spectroscopy, 31 P NMR, and 1 H NMR spectra reveal the passivation effect and hydrogen bonding interaction between TFEP and perovskite. As a result, the VOC is remarkably boosted from 1.04 to 1.10V, leading to a substantial gain in PCE from 14.97% to 17.78%. In addition, the unencapsulated PSC maintains the initial PCE of 80.1% for 1440h under air ambient of 40% RH. The work offers a fresh perspective on the rational design of high-performance HTL-free C-PSCs.

Intermediate phase-assisted growth of CsPbBr3 for high performance of carbon-based perovskite solar cells

Intermediate phase-assisted growth of CsPbBr3 for high performance of carbon-based perovskite solar cells

Efficient Carbon‐Based Perovskite Solar Cells Passivated by Alkylammonium Chloride

Hole‐transport layer (HTL)‐free carbon‐based perovskite solar cells (C‐PSCs) have garnered significant attention in the research community due to their cost‐effectiveness and high stability. However, the absence of a traditional HTL can lead to substantial nonradiative recombination of charge carriers between the perovskite layer and the carbon electrode, significantly impacting efficiency. Herein, the performance effects of different alkylammonium chlorides, including butylammonium chloride, octylammonium chloride, and dodecylammonium chloride (DACl), on perovskite (FA0.1MA0.9PbI3) are investigated to produce high‐performance HTL‐free C‐PSCs. Following passivation, the film exhibits a more uniform grain size distribution and fewer grain boundary defects. Furthermore, with an increase in the alkyl chain length, enhanced interactions with the perovskite film result in reduced trap state density and increased carrier lifetime. After DACl passivation, the C‐PSC achieves a remarkable power conversion efficiency of 16.56% and a high open‐circuit voltage (Voc) of 1.074 V. The Voc enhancement is primarily attributed to the better energy‐level alignment, effectively improving hole transport and electron‐blocking capabilities while suppressing nonradiative recombination. Additionally, they demonstrate exceptional hydrophobic characteristics and robust stability in the presence of humidity, making them particularly promising for future practical applications in the field of photovoltaics.

Enhancing the stability and efficiency of carbon-based perovskite solar cell performance with ZrO2-decorated rGO nanosheets in a mesoporous TiO2 electron-transport layer.

Improving the role of electron-transport layers (ETLs) in carbon-based perovskite solar cells (CPSCs) is a promising method to increase their photovoltaic efficiency. Herein, we employed rGO sheets decorated with ZrO2 nanoparticles to increase the electron transport capability of mesoporous TiO2 ETLs. We found that the rGO/ZrO2 dopant enhanced the conductivity of the ETL, reducing the charge-transfer resistance at the ETL/perovskite interface and reducing charge recombination in the corresponding CPSCs. Notably, this dopant did not effectively change the transparency of ETLs, while increasing the light-harvesting ability of their own top perovskite layer by improving the crystallinity of the perovskite layer. The rGO/ZrO2-containing ETLs produced a champion efficiency of 15.21%, while devices with a net ETL recorded a maximum efficiency of 11.88%. In addition, the modified devices showed a higher stability behavior against ambient air than the net devices, which was linked to the passivated grain boundaries of the modified perovskite layers along with the improved hydrophobicity.