Capillary Electrophoresis-electrospray Mass Spectrometry Research Articles

The Development of a Sheathless Interface for Capillary Electrophoresis Electrospray Ionization Mass Spectrometry Using a Cellulose Acetate Cast Capillary

The fabrication of a novel sheathless interface for capillary electrophoresis–electrospray–mass spectrometry (CE–ESI–MS) is described. A programmable CO2 laser was used to ablate small channels in the walls of a polyimide capillary near the terminus. Subsequent exposure of the channel region to a cellulose acetate solution followed by drying resulted in the formation of an electrically conductive semi-permeable membrane. Application of an appropriate voltage to the reservoir resulted in the simultaneous establishment of an electrical connection for CE and ESI. Interface viability was demonstrated by conducting a CE separation of a peptide mixture, with detection accomplished via positive ion mode ESI–MS. For the peptide Val-Tyr-Val, a limit of detection of 0.1 femtomole (S/N 3) was achieved using single reaction monitoring. Attributes of the interface include structural robustness, ease of fabrication, minimal interface dead volume, and the ability to alter post-separation analyte ionization status by use of appropriate buffers in the interface reservoir.

Analysis of free nucleotide monophosphates in human milk and effect of pasteurisation or high-pressure processing on their contents by capillary electrophoresis coupled to mass spectrometry

A simple, efficient and green analytical method for the determination of free nucleotide monophosphates in human milk is proposed. It involves centrifugal ultrafiltration (CUF) as sample treatment and capillary electrophoresis–electrospray mass spectrometry (CE–ESI-MS) for separation and simultaneous quantification.The optimised method, applied to the analysis of human milk samples, included their dilution (1:5) with water followed by CUF treatment. No matrix effects were found. The method provided limits of detection between 0.08 and 0.13μgmL−1 and limits of quantification between 0.26 and 0.43μgmL−1. The intralaboratory repeatability and reproducibility afforded relative standard deviation values lower than 10%.The method was applied to the study of the effects of Holder pasteurisation and high-pressure processing on the nucleotide contents in samples from a human milk bank. The results showed concentration values between 0.5 and 10μgmL−1, with higher concentrations for the samples treated by pasteurisation. The effect of freezing time on the content of nucleotides was also assessed.

Separation and characterization of superoxide dismutase 1 (SOD‐1) from human erythrocytes by capillary electrophoresis time‐of‐flight mass spectrometry

Cu, Zn-superoxide dismutase (SOD-1) is a homodimeric metalloenzyme that has been related to ALS (amyotrophic lateral sclerosis). The majority of ALS cases are sporadic while approximately 10% are inherited (familial ALS, FALS). Mutations in the amino acid sequence of human SOD-1 cause only 25% of the FALS cases, while the explanation for the rest is not clear yet. In this way, several authors have suggested the importance of posttranslational modifications or dimer dissociation on formation of the characteristic fatal intraneuronal SOD-1 aggregates. In this paper, we used capillary electrophoresis-electrospray mass spectrometry with an accurate mass and high-resolution time-of-flight mass spectrometer (CE-TOF-MS) for separation and characterization of standard bovine SOD-1 and human SOD-1 purified from erythrocytes. Two background electrolytes (BGEs) were used for CE-TOF-MS experiments in positive ion mode. An acidic BGE allowed detection of apo-monomer SOD-1, because the metal ions were completely released during the electrophoretic separation. The better sensitivity at acidic pH was especially interesting to detect different isoforms of human SOD-1. In contrast, a neutral BGE provided enhanced conditions for detection of the fully metalated dimeric and monomeric enzyme, but selecting an appropriate fragmentor voltage value in the TOF analyzer was critical to obtain reliable quantitative information. Anyway, only the metalated forms involving the main isoform of human SOD-1 were detected due to the lower sensitivity. Hence, the combination of both methodologies resulted necessary to obtain detailed structural information from the enzyme.

Simultaneous analysis of cocaine and its metabolites in urine by capillary electrophoresis–electrospray mass spectrometry using a pressurized liquid junction nanoflow interface

A new method for the simultaneous separation of cocaine and four metabolites in urine by CE-ESI-MS via a pressurized nanoliquid junction interface was developed. The resolution of cocaine, cocaethylene, benzoylecgonine, norcocaine, and ecgonine methyl ester was achieved in a polyvinyl-alcohol-coated capillary with 75 μm id × 50 cm total length, using a 15 mM ammonium formate electrolyte solution (pH 9.5) in less than 15 min. In addition, to enhance sensitivity, a field-amplified sample injection (FASI) was evaluated in terms of injection time and sample solvent composition. The limits of detection achieved with the FASI method ranged from 1.5 to 10 ng/mL for all the compounds. The detection of the studied compounds was performed using an ion-trap mass spectrometer in a positive ionization mode. A mixture of methanol:water (80:20 v/v) containing 0.1% v/v of formic acid was employed as spray liquid and delivered at ~200 nL/min. Under optimal CE-MS conditions, linearity was assessed in the concentration range of interest for all analytes with correlation coefficients r² ≥ 0.9913. Intra- and inter-day precision provided a relative standard deviation lower than 1.54% for migration times and lower than 12.15% for peak areas. Finally, urine samples, spiked with the standard mixture, were extracted using a solid-phase extraction procedure and injected under FASI conditions, providing recoveries from 80% to 94% for all analytes.

Analysis of recombinant human erythropoietin glycopeptides by capillary electrophoresis electrospray–time of flight-mass spectrometry

Capillary electrophoresis electrospray–mass spectrometry was used to detect and characterize the great variety of O- and N-glycopeptide glycoforms of recombinant human erythropoietin (rhEPO) using an orthogonal accelerating time-of-flight mass spectrometer to obtain their exact molecular masses (CE–TOF-MS). rhEPO was digested with trypsin and Glu-C and analyzed by CE–TOF-MS to detect O 126, N 83, N 24–N 38 and N 24 and N 38 glycopeptide glycoforms, respectively. Neuraminidase was first used to enhance the detection of the glycopeptides and detect all possible glycoforms contained in each glycosylation site. O 126 and N 83 glycopeptides were extensively characterized. Twelve sialoforms corresponding to 5 different glycoforms were detected in N 83, and for the first time, a sulfated sialoform of this glycopeptide was also detected. In the case of O 126, different sialoforms with different types of sialic acids (Neu5Gc and Neu5Ac) were detected and an estimation of the relative percentage of Neu5Gc versus Neu5Ac was also carried out for this glycopeptide. N 24 and N 38 glycosylation sites were also characterized by CE–TOF-MS after Glu-C digestion and these results permitted to rule out some glycan combinations for N 24–N 38 glycopeptide glycoforms. This study provided a reliable glycopeptide map of rhEPO and may be regarded as an excellent starting point to analyze rhEPO glycopeptides in biological fluids and detect the use of this hormone in sports.

Multi-component elemental and molecular analysis of lanthanides by capillary electrophoresis–electrospray mass spectrometry (CE–ESI-MS)

Electrospray mass spectrometry is a method of choice for individual elemental and molecular analysis of uncomplexed or complexed metal ions in solution. The multi-component elemental and molecular analysis of lanthanides is however hindered by the existence of isobaric interferences, therefore a previous chemical separation is required before mass spectrometric analysis. The whole lanthanide series has been separated by capillary electrophoresis using partial complexation and detected by electrospray mass spectrometry. The multi-component capability of coupled capillary electrophoresis–electrospray mass spectrometry for elemental and molecular analysis has been shown by adjusting the degree of declustering and molecular fragmentation in the mass spectrometer interface region. Three different modes have been defined as a function of the fragmentation potential applied (high, low and intermediate fragmentation potentials). For a high fragmentation potential, the system operates as an elemental detector: spectra representing mainly singly charged lanthanide oxide or lanthanide metal ion are observed. These spectra can be related to the dissociation energies of the lanthanide oxide bond and to the lanthanide electronic properties. For a low fragmentation potential, the system operates as a molecular detector: structural information on the mixed complexes formed in the capillary during the electrophoretic separation are obtained. The intermediate fragmentation potentials enable the study of the different steps of declustering.

Lowering the concentration limits of detection by on-line solid-phase extraction–capillary electrophoresis–electrospray mass spectrometry

The use of solid-phase extraction coupled on-line to capillary electrophoresis using electrospray mass spectrometry detection (SPE-CE-ESI-MS) is described for the analysis of peptides in dilute solutions. A SPE microcartridge or analyte concentrator containing C 18 derivatized silica particles as the extraction sorbent was easily constructed near the inlet of the separation capillary using commercially available materials. The reversed-phase sorbent selectively retained the target peptides, enabling large volumes of the sample to be introduced (>100 μL). The captured analytes were eluted in a small volume of an appropriate solution (20–50 nL). This resulted in sample clean-up and concentration enhancement, with minimum sample handling. As the SPE-CE conditions were compatible with on-line ESI-MS detection, the potential for identifying and characterizing the preconcentrated analytes by SPE-CE-ESI-MS using a sheath-flow CE-ESI-MS interface is also shown. Using separation electrolytes containing N-[carbamoylmethyl]-2-aminoethanesulfonic acid (ACES) at pH 7.4, an elution plug of 80:20 (v/v) (25 mM of formic acid in MeCN):H 2O and a sheath liquid of 20 mM of acetic acid in 50:50 (v/v) methanol:H 2O the concentration limits of detection for the analyzed peptides in the positive ion mode were lowered to nanogram per milliliter levels. The systematic optimization of the operational parameters involved in the development of the SPE-CE method is described in detail, in order to promote robust and quantitative SPE-CE-ESI-MS analysis and facilitate the widespread use of the technique.

Application of capillary electrophoresis mass spectrometry to the characterization of bacterial lipopolysaccharides

Capillary electrophoresis (CE) is a high-resolution technique for the separation of complex biological mixtures and has been widely applied to biological analyses. The coupling of capillary electrophoresis with mass spectrometry (MS) provides a powerful approach for rapid identification of target analytes present at trace levels in biological matrices, and for structural characterization of complex biomolecules. Here we review the analytical potential of combined capillary electrophoresis electrospray mass spectrometry (CE-MS) for the analysis of bacterial lipopolysaccharides (LPS). This hyphened methodology facilitates the determination of closely related LPS glycoform and isoform families by exploiting differences in their unique molecular conformations and ionic charge distributions by electrophoretic separation. On-line CE-MS also provides an additional avenue to improve detection limits, which has been successfully applied to directly probe oligosaccharide LPS glycoform populations of bacteria isolated from infected animal models without the need for further passage.

Functional Characterization of the Flagellar Glycosylation Locus in Campylobacter jejuni 81–176 Using a Focused Metabolomics Approach

Bacterial genome sequencing has provided a wealth of genetic data. However, the definitive functional characterization of hypothetical open reading frames and novel biosynthetic genes remains challenging. This is particularly true for genes involved in protein glycosylation because the isolation of their glycan moieties is often problematic. We have developed a focused metabolomics approach to define the function of flagellin glycosylation genes in Campylobacter jejuni 81-176. A capillary electrophoresis-electrospray mass spectrometry and precursor ion scanning method was used to examine cell lysates of C. jejuni 81-176 for sugar nucleotides. Novel nucleotide-activated intermediates of the pseudaminic acid (Pse5NAc7NAc) pathway and its acetamidino derivative (PseAm) were found to accumulate within select isogenic mutants, and use of a hydrophilic interaction liquid chromatography-mass spectrometry method permitted large scale purifications of the intermediates. NMR with cryo probe (cold probe) technology was utilized to complete the structural characterization of microgram quantities of CMP-5-acetamido-7-acetamidino-3,5,7,9-tetradeoxy-L-glycero-alpha-L-manno-nonulosonic acid (CMP-Pse5NAc7Am), which is the first report of Pse modified at C7 with an acetamidino group in Campylobacter, and UDP-2,4-diacetamido-2,4,6-trideoxy-alpha-D-glucopyranose, which is a bacillosamine derivative found in the N-linked proteinglycan. Using this focused metabolomics approach, pseB, pseC, pseF, pseI, and for the first time pseA, pseG, and pseH were found to be directly involved in either the biosynthesis of CMP-Pse5NAc7NAc or CMP-Pse5NAc7Am. In contrast, it was shown that pseD, pseE, Cj1314c, Cj1315c, Cjb1301, Cj1334, Cj1341c, and Cj1342c have no role in the CMP-Pse5NAc7NAc or CMP-Pse5NAc7Am pathways. These results demonstrate the usefulness of this approach for targeting compounds within the bacterial metabolome to assign function to genes, identify metabolic intermediates, and elucidate novel biosynthetic pathways.

Modelling migration behavior of peptide hormones in capillary electrophoresis-electrospray mass spectrometry

The applicability in capillary electrophoresis-electrospray mass spectrometry (CE-ESI-MS) of the classical semiempirical relationships between electrophoretic mobility and charge-to-mass ratio ( m e versus q/ M α ) has been investigated in order to describe the migration behavior of a series of bioactive peptide hormones. The influence upon the models of the separation electrolyte pH and the accuracy of the p K values of these compounds were studied first by capillary electrophoresis with ultraviolet detection (CE–UV). The classical polymer model, α = 1/2, resulted in slightly better correlations at any of the studied pH. Furthermore, a general linear equation can be adjusted combining all the experimental data pairs, which suggests that correlation in the whole pH range is independent of the ionic form of the studied peptide hormones. The plots of q/ M 1/2 against separation electrolyte pH were used to predict their electrophoretic separations, using the accurate p K values obtained in a previous work by CE–UV for charge calculations. A volatile separation electrolyte containing 50 mM of acetic acid and 50 mM of formic acid at pH 2.85 was selected for optimum CE–UV and CE-ESI-MS analysis of the peptide mixture. At this pH and taking into account the specific features of the coupling, the correlation using the classical polymer law was excellent and its parameters were similar to the ones of the general linear equation previously obtained by CE–UV. This confirmed the applicability in CE-ESI-MS of the semiempirical relationship originally established by CE–UV.

Capillary electrophoresis–electrospray mass spectrometry and HR–ICP–MS for the detection and quantification of 10B-boronophenylalanine (10B–BPA) used in boron neutron capture therapy

Boron neutron capture therapy (BNCT) is a bimodal radiotherapeutic treatment based on the irradiation of neoplastic tissues with neutrons after the tissues have selectively accumulated molecules loaded with nuclides with large neutron capture cross-sections (such boron-10). Boron-10 carriers have been tested to a limited extent, and clinical trials have been conducted on sulfhydryl borane (10B-BSH) and boronophenylalanine (10B-BPA). However, precise and accurate measurements of boron-10 concentrations (0.1-100 microg/g) in specimens and samples of limited size (microg scale) are needed in order to be able to biologically characterise new compounds in predictive tissue dosimetry, toxicology and pharmacology studies as well as in clinical investigations. A new approach based on fast separation and detection of 10B-BPA performed by coupling capillary electrophoresis to electrospray mass spectrometry is reported. This method allows the quantitative analysis and characterisation of 10B-BPA in a short time with a high separation efficiency. Detection limits of 3 microM for 10B-BPA and 30 ng/mL for 10B were obtained with CE-ESI-MS. A quantification limit of 10 microM for 10B-BPA (100 ng/mL for 10B) was attained. The total boron-10 concentration was determined by high-resolution inductively coupled mass spectrometry in order to validate the method. Boron-10 isotope measurements were carried out by HR-ICP-MS at medium resolution (R=4000) due to the presence of an isobaric interference at mass 10. Good agreement was obtained between the values from CE-ESI-MS and those from HR-ICP-MS. The method has been successfully used to determine the 10B-BPA in two lines of cultured cells.

Electrophoretic and mass spectrometric strategies for profiling bacterial lipopolysaccharides

Capillary electrophoresis (CE) is a high-resolution separation technique that has been widely used for trace analysis in biological samples. On-line capillary electrophoresis-electrospray mass spectrometry (CE-MS) was developed for the analysis of lipopolysaccharide (LPS) glycoforms from the gram-negative bacteria, Haemophilus influenzae. In this paper, we report on the application of CE-MS to characterize structural differences in O-deacylated LPS samples from H. influenzae strains Rd 11.7 and 375.1. The resolution capability of on-line CE-MS was first demonstrated by analysis of a complex LPS mixture from H. influenzae strain Rd 11.7. This strain contains a mixture of isomeric glycoforms differing in the number and positions of hexose moieties. Sialic acid containing glycoforms were also determined. Structural features of LPS from a lic1 mutant of H. influenzae strain 375 (375.1) were studied using on-line CE-MS/MS. With the separation provided by CE, two isomeric glycoforms differing in the location of phosphoethanolamine substituents were characterized by tandem mass spectrometry.

Metabolome analysis: the potential of in vivo labeling with stable isotopes for metabolite profiling

Metabolome analysis technologies are still in early development because, unlike genome, transcriptome and proteome analyses, metabolome analysis has to deal with a highly diverse range of biomolecules. Combinations of different analytical platforms are therefore required for comprehensive metabolomic studies. Each of these platforms covers only part of the metabolome. To establish multiparallel technologies, thorough standardization of each measured metabolite is required. Standardization is best achieved by addition of a specific stable isotope-labeled compound, a mass isotopomer, for each metabolite. This suggestion, at first glance, seems unrealistic because of cost and time constraints. A possible solution to this problem is discussed in this article. Saturation in vivo labeling with stable isotopes enables the biosynthesis of differentially mass-labeled metabolite mixtures, which can be exploited for highly standardized metabolite profiling by mass isotopomer ratios.

Pressurized liquid extraction–capillary electrophoresis–mass spectrometry for the analysis of polar antioxidants in rosemary extracts

A method based on capillary electrophoresis–electrospray–mass spectrometry (CE–ESI–MS) was developed to qualitatively characterize natural antioxidants from rosemary ( Rosmarinus officinalis L.) in different fractions obtained by pressurized liquid extraction (PLE) using subcritical water. The parameters of CE–ESI–MS were adjusted allowing the separation and characterization of different compounds from rosemary in the PLE fractions. These parameters for CE are kind, pH and concentration of the separation buffer, parameters for ESI–MS are dry gas temperature and flow, nebulizing gas pressure, and make-up flow. The following analytical conditions were found most favorable: aqueous CE buffer (40 mM ammonium acetate/ammonium hydroxide, pH 9); sheath liquid containing 2-propanol–water (60:40, v/v) and 0.1% (v/v) triethylamine at a flow rate of 0.24 mL/h; drying gas flow rate equal to 7 L/min at 350 °C, nebulizing gas pressure of 13.8 kPa (2 psi), using a compound stability of 50%. Different antioxidant compounds (e.g., rosmarinic acid and carnosic acid) could be detected in the rosemary extracts by CE–ESI–MS without any additional treatment, enabling the determination of variations in the extract composition caused by the different PLE conditions (i.e., 60 and 100 °C). The results provide complementary information to HPLC analysis.

Direct automatic determination of biogenic amines in wine by flow injection‐capillary electrophoresis‐mass spectrometry

A capillary electrophoresis-electrospray mass spectrometry (CE-ESI-MS) method for the separation and determination of nine biogenic amines is proposed. Operational variables, such as the voltage, temperature, sheath liquid composition, flow-rate, and MS parameters, were optimized. Samples are injected in the hydrodynamic mode into a 75 cm x 50 microm ID coated capillary and separated by using 25 mM citric acid at pH 2.0. Heptylamine is used as internal standard. The experimental setup includes a flow manifold coupled to the CE system for automatic insertion of samples into the CE vials. The proposed method allows amines to be determined with limits of detection from 0.018 to 0.09 microg x mL(-1) and relative standard deviation (RSD) values from 2.4% to 5.0% (except 6.8% for histamine). The method was successfully used to determine biogenic amines in red and white wines.

Coupling capillary electrophoresis and high-field asymmetric waveform ion mobility spectrometry mass spectrometry for the analysis of complex lipopolysaccharides.

High-field asymmetric waveform ion mobility spectrometry (FAIMS) is a new technology for atmospheric pressure, room temperature separation of gas-phase ions. The FAIMS system acts as an ion filter that can continuously transmit one type of ion, independent of mass-to-charge ratio (m/z). Capillary electrophoresis-electrospray mass spectrometry (CE-MS) has been extensively used for the analysis of complex bacterial lipopolysaccharides (LPS). The coupling of FAIMS to CE-MS provides a sensitive technique for the characterization of these complex glycolipids, permitting the separation of trace-level LPS oligosaccharide glycoforms for subsequent structural characterization using tandem mass spectrometry. This was demonstrated for LPS from nontypeable Haemophilus influenzae strain 375 following O-deacylation with anhydrous hydrazine. This strain of H. influenzae can express a triheptosyl-containing glycoform to which four hexose residues are linked forming the outer-core region of the molecule. This has been referred to as the Hex4 glycoform. Glycoforms have been identified which differ in the number of phosphoethanolamine substituents in the inner-core. With the use of CE-FAIMS, isomeric Hex4 glycoforms containing two PEtn groups were separated and characterized by MS/MS. FAIMS provided a significant reduction in mass spectral noise, leading to improved detection limits ( approximately 70 amol of the major glycoform). The extracted mass spectrum showed that the apparent noise was virtually eliminated. In addition to the reduction of chemical background, the ion current was increased by as much as 7.5 times as a result of the atmospheric pressure ion-focusing effect provided by the FAIMS system. The linearity of response of the CE-FAIMS-MS system was also studied. The calibration curve is linear for approximately 3 orders of magnitude, over a range of 40 pg/microL to 10 ng/microL.

Applicability of predictive models to the peptide mobility analysis by capillary electrophoresis–electrospray mass spectrometry

The prediction of peptide mobility by capillary electrophoresis (CE) coupled to electrospray mass spectrometry (MS) is studied in order to verify the validity of the semi-empirical models developed in classical CE. This work relies on the experimental determination of the electrophoretic mobilities of 68 peptides, different in charge and in size. The results indicate that the prediction is possible in CE–MS experiments, in spite of the restraints inherent in the coupling conditions. The best fit of experimental data was obtained with the Offord’s model. The efficiency of the model was confirmed by the analysis of a peptide mixture in CE–MS.

Structural, genetic and functional characterization of the flagellin glycosylation process in Helicobacter pylori.

Mass spectrometry analyses of the complex polar flagella from Helicobacter pylori demonstrated that both FlaA and FlaB proteins are post-translationally modified with pseudaminic acid (Pse5Ac7Ac, 5,7-diacetamido-3,5,7,9-tetradeoxy-l-glycero-l-manno -n o n-ulosonic acid). Unlike Campylobacter, flagellar glycosylation in Helicobacter displays little heterogeneity in isoform or glycoform distribution, although all glycosylation sites are located in the central core region of the protein monomer in a manner similar to that found in Campylobacter. Bioinformatic analysis revealed five genes (HP0840, HP0178, HP0326A, HP0326B, HP0114) homologous to other prokaryote genes previously reported to be involved in motility, flagellar glycosylation or polysaccharide biosynthesis. Insertional mutagenesis of four of these homologues in Helicobacter (HP0178, HP0326A, HP0326B, HP0114) resulted in a non-motile phenotype, no structural flagella filament and only minor amounts of flagellin protein detectable by Western immunoblot. However, mRNA levels for the flagellin structural genes remained unaffected by each mutation. In view of the combined bioinformatic and structural evidence indicating a role for these gene products in glycan biosynthesis, subsequent investigations focused on the functional characterization of the respective gene products. A novel approach was devised to identify biosynthetic sugar nucleotide precursors from intracellular metabolic pools of parent and isogenic mutants using capillary electrophoresis-electrospray mass spectrometry (CE-ESMS) and precursor ion scanning. HP0326A, HP0326B and the HP0178 gene products are directly involved in the biosynthesis of the nucleotide-activated form of Pse, CMP-Pse. Mass spectral analyses of the cytosolic extract from the HP0326A and HP0326B isogenic mutants revealed the accumulation of a mono- and a diacetamido trideoxyhexose UDP sugar nucleotide precursor.

Rapid identification of proteins in polyethylene glycol-containing samples using capillary electrophoresis electrospray mass spectrometry

Rapid identification of proteins in polyethylene glycol-containing samples using capillary electrophoresis electrospray mass spectrometry

Capillary electrophoresis-electrospray mass spectrometry for the characterization of high-mannose-type N-glycosylation and differential oxidation in glycoproteins by charge reversal and protease/glycosidase digestion.

The characterization of high-mannose-type N-glycosylation by capillary electrophoresis-electrospray mass spectrometry (CE-ESI MS) was described. In addition to the use of a cationic noncovalent capillary coating, strong acidic buffer, and charge reversal to increase the glycoform resolving power, N-glycosidase F (PNGase F) combined with a basic protease and alpha-mannosidase combined with an acidic protease were used to analyze the high-mannose-type N-glycosylation in ribonuclease B (RNase B) and in a novel C-type lectin from the venom of Trimeresurus stejnegeri (TSL). The structures of oligosaccharide, glycosylation sites, and glycoform distributions were determined simultaneously, and the differential oxidation of Met residues in glycopeptides obtained from TSL protease digestion was also characterized successfully by CE-MS/MS. The results showed that the oligosaccharide attached to RNase B has a structure of GlcNAc2Man5 approximately 9, and that attached to TSL has a structure of GlcNAc2Min5 approximately 8. The glycoform distributions in these glycoproteins are quite different, with the GlcNAc2Man5 type predominant in RNase B, and the GlcNAc2Man8 type, in TSL This method may be useful not only for the characterization of glycosylation sites and glycan structures, but also for the determination of the relative abundance of individual glycoforms.