Capacity Ratio Research Articles

Evaluation of the Potential Flight Ability of the Casuarina Moth, Lymantria xylina (Lepidoptera: Erebidae).

Lymantria xylina Swinhoe (Lepidoptera: Erebidae) is a potentially invasive pest, similar to Lymantria dispar asiatica Vnukovskij and Lymantria dispar japonica Motschulsky (Lepidoptera: Erebidae). To evaluate its potential for spread and flight distance related to egg deposition on vessels at ports, we employed a flight mill to assess the flight capabilities of its adults under varying conditions. Our findings revealed that females primarily flew short distances and ceased flying after 3:00 AM, whereas males covered much longer distances throughout the day. Sex, age, and flight duration significantly influenced flight ability. Females exhibited weaker flight capability than males, and their ability declined with increasing age or flight duration. Notably, 1-day-old moths displayed the strongest flight ability, with average flight distances of up to 3.975 km for females and 8.441 km for males. By the fifth day, females no longer flew, and males experienced reduced flight ability. After continuous hanging for 16 h, females lost most of their flight capacity, while males remained capable of flight even after 32 h. Additionally, female flight ability decreased significantly after mating, possibly due to factors such as egg-carrying capacity, weight, and load ratio. This study provides a foundation for assessing the risk of long-distance dispersal of L. xylina via ocean-going freighters, considering female moths' phototactic flight and oviposition.

The impact of arable soil management on physical functions – The ratio of air capacity and air permeability or hydraulic conductivity as a document of harmful soil compaction

Soil health or soil degradation criteria are until now not well documented for a greater number of soil profiles under conventional and conservation tillage management in the literature. In order to evaluate the compaction status of more than 700 arable sites analyzed within the last 40 years, the Compaction Verification Tool (CVT) was applied according to Zink et al. (2011). Besides the ratio of air capacity (AC, at a matric potential of −6 kPa) and saturated hydraulic conductivity (Ks), the ratio of AC and air conductivity (Ka, at a matric potential of −6 kPa) was considered for evaluating the compaction status with respect to potentially harmful soil alterations. The compaction status was classified into the CVT classes I–IV, where a harmful subsoil compaction was assumed, if both values of AC and Ks or AC and Ka simultaneously exceeded (are smaller than) their defined critical value indicating limited conditions for plant growth (CVT class IV). We analyzed the compaction status of soil profiles with respect to clay content, soil type, structural stage (aggregate forms) and time span of sampling (1980–1999, 2000–2020) under conventional and conservation tillage for top- and subsoil horizons. While also some of the annually plowed topsoils under conventional tillage showed critical values of AC, Ks and Ka, the occurrence of harmful soil compaction is most dominant in the subsoil horizons (> 30 cm depth) because of a higher proportion of class IV which increased with the clay content (from < 12 % to > 12 % clay), irrespective of the applied ratio used for verification (AC/Ks or AC/Ka). Especially the highly productive Luvisols showed a high percentage of harmful compaction in the subsoil (30–41 % in CVT class IV). Soil profiles under conservation tillage management are less affected by harmful compaction. The more aggregated subsoils showed smaller proportions of class IV, which was further influenced by the clay content.

An Investigation into the Variables Influencing the Structural Bamboo Architecture Using Filled Concrete and Cement Mortar

Bamboo, as a green building material, plays a vital role in construction. Bamboo has good properties and appearance, making it highly attractive for building structures and designs. Since the compressive capacity of bamboo is considerably lower than its tensile capacity, with the ratio typically ranging between 300% to 900%, this limits its application dimensions in construction. Therefore, filling the original bamboo structural members with specific materials or applying different connection methods can not only maintain the appearance of the bamboo structure but also improve its compressive capacity and overall durability, thus expanding the application range of bamboo structural members and enhancing the performance of the architectural design process. Two hollow bamboo specimens were among the eight BFC specimens tested for this paper. Key components such as transverse stiffeners, steel bars, filler materials, and bamboo nodes were examined for their influence on the specimens’ ductility, peak strain, ultimate bearing capacity, and failure mechanisms. The test results showed that the ratio of the ultimate bearing capacity of BFC specimens to hollow bamboo samples could reach up to 538%, while the peak strain differences were minimal. A non-linear finite element model was developed and its accuracy confirmed based on the test results. This work proposes a new approach to determine the final axial compressive capacity of BFC columns by creating an elastic model of transversely isotropic cylinders. As a result, the primary goal of this study is to establish a foundation for more scientific building design techniques and procedures by examining the axial compression mechanics of structural bamboo filled with cement and concrete (BFC) and how it influences building design.

ВПЛИВ ВЕЛИЧИНИ ЄМНОСТІ ПОСЛІДОВНОГО РЕЗОНАНСНОГО КОНТУРУ НА ПОТУЖНІСТЬ ЕЛЕКТРОТЕХНІЧНИХ СИСТЕМ РЕЗОНАНСНОГО ТИПУ ДЛЯ МОНІТОРИНГУ ІЗОЛЯЦІЇ ВИСОКОВОЛЬТНОГО ОБЛАДНАННЯ

It were analyzed the processes of charging the capacitive electro-technical storage (CES), which can be the electrical insulation of modern high -voltage equipment (in particular power cables) during the current monitoring of its techni-cal condition by the value of leakage currents when applying high voltage to insulation. The transformerless electro-technical system (ETS) of a resonance type, in which resonant inductive-capacitive circuit (ICС) with a high Q -factor carried out a multiple increase in AC voltage, was used to generate such voltage. Analytical expressions were obtained for the steady-state voltage on such CES and transient currents in the ETS circuit its charging. Simulation modeling of transient processes in the circuits of such ETS during CES charging was performed using the LTSpice software pack-age. It is shown that the dependences of the output voltage and current of the ETS on time, obtained by analytical ex-pressions, practically coincide with the results of simulation simulations. The influence of the ratio of the load capaci-tance and the resonant circuit capacitance on the relative load charging time and, accordingly, on the ETS power was studied. It was found that in order to increase the power of high -voltage transformerless ETS of the specified reso-nance type, it is necessary to increase the ratio of the CES capacity to the ICС capacity of the resonant circuit of the ETS. This approach can be used when using ETS with resonant ICCs to create powerful electric discharge installations (EDIs) for the implementation of technologies for obtaining electro-spark micro- and nanopowders with unique opera-tional properties. When creating powerful EDIs, it is suggested to use the value of the above-mentioned ratio at least 10. References 31, figures 5.

Expiratory Venous Volume and Arterial Tortuosity are Associated with Disease Severity and Mortality Risk in Patients with COPD: Results from COSYCONET.

The aim of this study was to evaluate the association between computed tomography (CT) quantitative pulmonary vessel morphology and lung function, disease severity, and mortality risk in patients with chronic obstructive pulmonary disease (COPD). Participants of the prospective nationwide COSYCONET cohort study with paired inspiratory-expiratory CT were included. Fully automatic software, developed in-house, segmented arterial and venous pulmonary vessels and quantified volume and tortuosity on inspiratory and expiratory scans. The association between vessel volume normalised to lung volume and tortuosity versus lung function (forced expiratory volume in 1 sec [FEV1]), air trapping (residual volume to total lung capacity ratio [RV/TLC]), transfer factor for carbon monoxide (TLCO), disease severity in terms of Global Initiative for Chronic Obstructive Lung Disease (GOLD) group D, and mortality were analysed by linear, logistic or Cox proportional hazard regression. Complete data were available from 138 patients (39% female, mean age 65 years). FEV1, RV/TLC and TLCO, all as % predicted, were significantly (p < 0.05 each) associated with expiratory vessel characteristics, predominantly venous volume and arterial tortuosity. Associations with inspiratory vessel characteristics were absent or negligible. The patterns were similar for relationships between GOLD D and mortality with vessel characteristics. Expiratory venous volume was an independent predictor of mortality, in addition to FEV1. By using automated software in patients with COPD, clinically relevant information on pulmonary vasculature can be extracted from expiratory CT scans (although not inspiratory scans); in particular, expiratory pulmonary venous volume predicted mortality. NCT01245933.

High Modulus Na2SiO3‐Rich Solid Electrolyte Interphase Enable Long‐Cycle and Energy‐Dense Sodium Metal Battery

AbstractSodium metal battery is considered as one of the most promising energy storage/conversion devices due to their high energy density, and abundant sodium reserves. However, its development is hampered by the limited metallic utilization and detrimental sodium dendrite growth ascribed to the unstable, and fragile solid electrolyte interphase (SEI). Here, the high stable and modulus SEI is constructed with a component of a thin and dense layer of high Na‐ion conductive Na2SiO3. It is in situ formed by the reaction between sodium anode and fish‐skin structure separator, which exhibits a 3D porous polyvinylidene fluoride‐based framework embedded with thin and robust vermiculite sheets. The robust interphase cannot only suppress sodium dendrite growth but also enable high energy density with small interphase‐consumed Na ions in anode‐less batteries. Accordingly, the as‐assembled NaNi1/3Fe1/3Mn1/3O2//Na cell shows 83% capacity retention after 5000 cycles at a rate of 5 °C. Moreover, the proof‐of‐concept pouch cells deliver an energy density of 205 Wh kg−1 (based on the total mass of the battery), and high safety (not catching fire after punctured) under anode‐less condition (with a low negative/positive capacity ratio of ≈2.1).

Liquidizing crystal MIL-100(Fe) to coating silica powder for purifying wastewater

Although MIL-100(Fe) was regarded as an ideal material for the environmental remediation, it could not be applied in practical because of the potential eco-environmental risk and cost. In this work, a novelty strategy of liquidizing crystal MIL-100(Fe) was posted for the first time through inhibiting the crystallization process and forming physical MIL-100(Fe) gel. Due to this MIL-100(Fe) sol–gel, MIL-100(Fe) could easy cover on the surface of silica powder (SiO2) through simple soaking operation. MIL-100(Fe) covering on SiO2 (MIL-100(Fe)@SiO2) could be quickly separated from wastewater spontaneously owing to the carrier of SiO2, even in a tank of 2.0 m, which made it possible for purifying wastewater in practical. MIL-100(Fe)@SiO2 could remove phosphate with a removing ratio of closing 100 % at an initial concentration of 10 mg/L, while more than 95 % towards methyl orange (MO). The removing ratio of MO by MIL-100(Fe)@SiO2 did not obviously decrease when the concentration of MO increased to 100 mg/L. And the adsorption performance of phosphate did not affect by pH among 3.0–9.0. The adsorption amount exceeded 50 % of maximum adsorption capacity for phosphate within 30 min, while 90 % for MO. Monodentate mononuclear coordination could explain the adsorption of phosphate by MIL-100(Fe)@SiO2. The N atom in MO might be acted as Lewis acid to coordinate with MIL-100(Fe)@SiO2. After adsorption, the P-saturated and MO-saturated MIL-100(Fe)@SiO2 could be effectively regenerated by the dilute HCl and NaOH solution, respectively. The recovery ratio of adsorption capacity for phosphate and MO were up to 97.7 % and 71.6 %.

Lithium Plating Characteristics in High Areal Capacity Li-Ion Battery Electrodes.

Li-ion battery degradation and safety events are often attributed to undesirable metallic lithium plating. Since their release, Li-ion battery electrodes have been made progressively thicker to provide a higher energy density. However, the propensity for plating in these thicker pairings is not well understood. Herein, we combine an experimental plating-prone condition with robust mesoscale modeling to examine electrode pairings with capacities ranging from 2.5 to 6 mAh/cm2 and negative to positive (N/P) electrode areal capacity ratio from 0.9 to 1.8 without the need for extensive aging tests. Using both experimentation and a mesoscale model, we identify a shift from conventional high state-of-charge (SOC) type plating to high overpotential (OP) type plating as electrode thickness increases. These two plating modes have distinct morphologies, identified by optical microscopy and electrochemical signatures. We demonstrate that under operating conditions where these plating modes converge, a high propensity of plating exists, revealing the importance of predicting and avoiding this overlap for a given electrode pairing. Further, we identify that thicker electrodes, beyond a capacity of 3 mAh/cm2 or thickness >75 μm, are prone to high OP, limiting negative electrode (NE) utilization and preventing cross-sectional oversizing the NE from mitigating plating. Here, it simply contributes to added mass and volume. The experimental thermal gradient and mesoscale model either combined or independently provide techniques capable of probing performance and safety implications of mild changes to electrode design features.

Assessing post-COVID-19 respiratory dynamics: a comprehensive analysis of pulmonary function, bronchial hyperresponsiveness and bronchodilator response.

Coronavirus disease 2019 (COVID-19) has a considerable impact on the global healthcare system. Individuals who have recovered from COVID often experience chronic respiratory symptoms that affect their daily lives. This study aimed to assess respiratory dynamics such as airway hyperresponsiveness (AHR) and bronchodilator response in post-COVID patients. This study included 282 adults with respiratory symptoms who underwent provocation tests. The demographic details, clinical symptoms and medical histories were recorded. Baseline spirometry, methacholine challenge tests (MCT) and post-bronchodilator spirometry were performed. Patients were divided into the following four groups: Group 1: non-COVID-19 and negative MCT; Group 2: post-COVID-19 and negative MCT; Group 3: non-COVID-19 and positive MCT; and Group 4: post-COVID-19 and positive MCT. Most post-COVID-19 patients (43.7%) experienced AHR, and wheezing was more common. Patients in Group 4 exhibited increased intensities of dyspnoea, cough and wheezing with the lowest pulmonary function test (PFT) parameters at baseline. Moreover, significant decreases in PFT parameters after the MCT were observed in these patients. Although the prevalence of a low forced expiratory volume in 1 s to forced vital capacity ratio (<70%) was initially 2% in Group 4, it increased to 29% after MCT. No significant differences in allergic history or underlying diseases were observed between the groups. These findings provide comprehensive insights into the AHR and respiratory symptoms of post-COVID-19 individuals, highlighting the characteristics and potential exacerbations in patients with positive MCT results. This emphasises the need of MCT to address respiratory dynamics in post-COVID-19 individuals.

Geogrid reinforcement for improving bearing capacity and stability of square foundations

Abstract Shallow foundations are often the most economical option for building support, as they distribute structural weight to soil layers, require minimal earthwork, and do not necessitate specialized machinery. The most common type of soil in the city of Karbala is sandy soil. It is granular and loose by nature which has a relatively low bearing capacity. According to previous studies, the soil weakness is one of the problems with shallow foundation construction. Thus, the aim of this study is to improve the properties of the soil using geogrid reinforcement. Three critical parameters are examined, including depth, size, and number of geogrid layers in the soil reinforcement process to increase bearing capacity and decrease soil settling. The effect of geogrid depth (u) was studied by considering four depth ratios (u/B = 0.5, 1.0, 1.5, and 2.0) in order to determine the ideal depth of the geogrid layer, where (B) refers to the width of the footings. The results indicated that a decrease in depth ratio significantly increased the bearing capacity of footings built on reinforced soil layers compared to those built on natural soil, and the settlement reduction ratio (SRR) also increased. The size of the geogrid layer (i.e., width of the geogrid layer (b) was evaluated by evaluating four size ratios (b/B = 1.5, 3.0, 4.5, and 6.0). With an increasing size ratio of the geogrid layer, the bearing capacity ratio (BRC) was significantly improved. Additionally, the study examined the optimal number of geogrid layers, focusing on single and multiple layers with N = 1, 2, 3, and 4. The results showed a higher BRC for footings on reinforced soil layers, as well as a significant rise in SRR with an increase in the number of geogrid layers. Finally, it was concluded that the optimal depth ratio was u/B = 0.5, the size ratio was b/B = 4.5, and reinforced with three geogrid layers, which provided the highest bearing capacity and SRR. The experimental test results were verified by comparing them with those calculated using theoretically developed models. The variation between the experimental and theoretical results is reasonable, confirming that the experimental testing results exhibit a high degree of accuracy.

A novel correlation-based approach for combined estimation of state of charge and state of health of lithium-ion batteries

State of charge(SOC) and state of health(SOH) estimation are two critical aspects for the secure operation and echelon utilisation of lithium-ion batteries. Considering the two states are interrelated, combined estimation methods are desired in practice. However, previous machine learning-based or traditional filter-based techniques have high computational requirements or suffer from convergence issues. To this end, the combined SOC and SOH estimation method of lithium-ion batteries using the novel correlation between SOC and SOH is proposed in this study. Specifically, a correlation between the capacity ratio for constant-current charging process and constant-voltage charging process and capacity loss is established. Extended Kalman filter is adopted to track SOC values at the end of constant current charging process instead of relying on the entire charging process during online application and SOH estimation can be accomplished in only one step based on the established correlation. The results show that the proposed combined SOC and SOH estimation method enables precise SOC estimation during both charging and discharging processes and achieves reliable estimation results during battery degradation. Additionally, the proposed method offers a swift means of estimating SOH with guaranteed estimation accuracy.

Association between dietary niacin intake and lung function among American adults: A cross-sectional analysis from national health and nutrition examination survey, 2007–2012

BackgroundThe pathogenesis of pulmonary senescence involves immune system dysregulation, oxidative stress, and mitochondrial dysfunction. The effects on lung function of niacin, an essential coenzyme involved in mitochondrial energy metabolism with known antioxidant properties, are poorly understood. MethodsThis cross-sectional study used data from the 2007–2012 National Health and Nutrition Examination Survey, including spirometry data and niacin intake information of 9706 adults. This study investigated various spirometry measures, such as forced expiratory volume in 1 s, forced vital capacity, pulse expiratory flow, (forced expiratory volume in 1 s)/(forced vital capacity)ratio, and predicted forced expiratory volume in 1 s and forced vital capacity percentages. Additionally, a secondary analysis was conducted using Global Initiative for Chronic Obstructive Lung Disease and chronic obstructive pulmonary disease. Foundation Spirometry Grade criteria to assess the relationship between niacin intake, airflow limitation, and obstruction. Multivariate regression models were used to adjust for relevant covariates. ResultsThe study included 9706 U S. adults (4788 men and 4918 women) with a median age of 46.2 years. After adjusting for relevant factors, a positive correlation was observed between niacin intake and lung function. Compared to the lowest quintile of niacin intake (Q1, ≤14.5 mg/day), individuals in the highest quintile (Q5, >34.5 mg/day) exhibited significant increases in lung function parameters, including forced expiratory volume in 1s (69.84 mL, p = 0.003), pulse expiratory flow (254.48 mL, p < 0.001), (forced expiratory volume in 1 s)/(forced vital capacity)(0.01, p = 0.041), percent predicted forced expiratory volume in 1 s(2.05, p = 0.002), and percent predicted forced vital capacity(1.29, p = 0.042).Subset analyses of individuals with spirometry-defined airflow obstruction showed associations of high niacin intake with significantly improved forced expiratory volume, pulse expiratory flow, and percent predicted pulse expiratory flow and an interaction among race, education, and smoking status with respect to the relationship between niacin intake and lung function parameters. ConclusionsHigher niacin intake was associated with increased measures of lung function. A diet rich in niacin-containing foods may play a role in improving lung health.

Interfacial Layers with Desolvation Function Induced Stable Deposition of Lithium Metal for Long-Cycling Lithium Metal Batteries.

The unstable solid electrolyte interface (SEI) formed by uncontrollable electrolyte degradation, which leads to dendrite growth and Coulombic efficiency decay, hinders the development of Li metal anodes. A controllable desolvation process is essential for the formation of stable SEI and improved lithium metal deposition behavior. Here, we show a functional artificial interface protective layer comprised of chondroitin sulfate-reduced graphene oxide (CrG), on which polar functional groups are distributed to effectively reduce the energy barrier for desolvation of Li+ and effectively alienate solvent molecules to avoid solvent involvement in SEI formation, thus promoting the formation of a LiF-rich SEI. Consequently, stable Coulombic efficiencies of 98.4% were achieved after 500 cycles in a Li//Cu cell. Moreover, the LiFePO4 full cells achieve steady circulation (470 cycles at 80%, 1 C) with a negative/positive electrode capacity ratio of 2.87. Our multifunctional artificial interface protective layer provides a new way to advance Li metal batteries.

Extended Plateau Capacity of Hard Carbon Anode for High Energy Lithium-Ion Batteries.

Hard carbon materials have shown promising potential for sodium-ion storage due to accommodating larger sodium ions. However, as for lithium-ion storage, the challenge lies in tuning the high lithiation plateau capacities, which impacts the overall energy density. Here, hard carbon microspheres (HCM) are prepared by tailoring the cross-linked polysaccharide, establishing a comprehensive methodology to obtain high-performance lithium-ion batteries (LIBs) with long plateau capacities. The "adsorption-intercalation mechanism" for lithium storage is revealed combining in situ Raman characterization and ex situ nuclear magnetic resonance spectroscopy. The optimized HCM possesses reduced defect content, enriched graphitic microcrystalline, and low specific surface area, which is beneficial for fast lithium storage. Therefore, HCM demonstrates a high reversible capacity of 537mAhg-1 with a significant low-voltage plateau capacity ratio of 55%, high initial Coulombic efficiency, and outstanding rate performance (152mAhg-1 at 10Ag-1). Moreover, the full cell (HCM||LiCoO2) delivers outstanding fast-charging capability (4min charge to 80% at 10C) and impressive energy density of 393Whkg-1. Additionally, 80% reversible capacity can be delivered under -40°C with competitive cycling stability. This work provides in-depth insights into the rational design of hard carbon structures with extended low-voltage plateau capacity for high energy LIBs.

Effects of different drying techniques of ground sprouted chickpeas on quality, textural properties, and sensory attributes of fried falafel

AbstractThe process of sprouting makes legumes better by changing their nutrition, chemicals, and taste. Ground sprouted chickpeas are commonly used as the main ingredient in falafel. The aim of this research was to study the impact of drying techniques that include hot‐air, infrared, and microwave on the moisture, ash, total phenolics, antioxidant capacity, color, and rehydration ratio of dried ground sprouted chickpeas. Also, the effects of drying techniques of ground sprouted chickpeas on the moisture, ash, total phenolics, antioxidant activity, color, volume, density, oil content, textural properties, and sensory attributes of fried falafel were examined. The total phenolics of hot‐air‐dried, infrared‐dried, and microwave‐dried samples were 463.42, 766.20, and 470.82 μg Gallic acid (GA)/g dry, respectively. The infrared‐dried ground sprouts had the highest antioxidant capacity. Additionally, the total phenolic content and antioxidant capacity of fried falafels made from infrared‐dried ground sprouted chickpeas were significantly higher than those of the fried falafels made from hot‐air‐dried and microwave‐dried sprouts (p &lt; .05). The mean values of lightness, redness, and yellowness of the fried falafel core ranged from 57.37 to 59.29, 3.66 to 6.88, and 40.50 to 43.31, respectively. The lowest oil absorption was related to the sample prepared from the hot‐air‐dried sprouted chickpeas (p &lt; .05). The firmness, cohesiveness, springiness, and chewiness of the fried falafels were between 38.17 N and 91.56 N, 0.29 and 0.44, 0.48 and 0.58, and 5.38 N and 17.24 N, respectively. The use of infrared‐dried sprouted chickpeas for producing fried falafel, due to the highest odor, flavor, and overall acceptance scores, high phenolic compounds and antioxidant activity, high volume, low density, and low hardness, is recommended.

Coal gasification fine slag derived porous carbon-silicon composite as an ultra-high capacity adsorbent for Rhodamine B removal

The extensive release of industrial solid wastes and organic dyes has led to severe environmental pollution, underscoring the urgent need to recycle these solid wastes and to remove the dyes. Herein, a porous carbon-silicon composite (PC-SiO2) is synthesized using coal gasification fine slag (CGFS) as a precursor via an alkali (KOH) activation and an acid (HCl) etching process, and used as an adsorbent for the Rhodamine B (RhB) removal. The as-synthesized PC-SiO2 possesses an ultra-high specific surface area of 1275.63 m2/g, a large pore volume of 0.26 cm3/g, and enriched reactive functional groups (e.g., Si-OH and –COOH). Due to these features, the actual adsorption capacity and removal ratio of the PC-SiO2 for RhB were as high as 1383.72 mg/g and 92.25 %, respectively, at 298.15 K and pH = 7. Further studies indicate that the adsorption of RhB on PC-SiO2 fits both the pseudo-second-order kinetic model and the Langmuir model, with the maximum equilibrium adsorption capacity being 1388.89 mg/g as predicted by the Langmuir model. The adsorption process involves the electrostatic attraction, hydrogen bonding, π-π interaction, and pore-filling mechanism. This work not only offers a novel approach for removing organic dyes from industrial wastewater but also provides an effective strategy for producing high-value-added materials from industrial solid wastes.

Characteristics of CPO Extraction Results from Spinner Machine Test Capacity 15-45 Kg for Home Industrial Scale

Purpose: This research aims to obtain the characteristics of CPO extraction results using a home industry spinner machine and determine the capacity of palm fruit suitable for CPO extraction using the spinner machine. Methodology: The spinner machine tested used a speed of 1800 rpm for 15 minutes, with capacity ratios of 15, 30, and 45 kg. The spinning process produces oil that will come out through the oil drain hole. Testing these three capacities will determine which one is more capable of producing CPO oil and is safe for engine rotation. Observing the characteristics of CPO involved yield tests, free fatty acid (FFA) tests, impurity content tests, and water content tests. Results: The yield test results ranged from 19.66% to 21.6%, the FFA test results ranged from 4.096% to 5.376%, the water content test results ranged from 0.2% to 0.6%, and the dirt content test results ranged from 2% to 5%. Findings: The 30 kg capacity was the most effective and efficient for CPO extraction using the home industry spinner machine. Novelty: The use of spinner machines in the home industry for CPO extraction has not been widely studied, and this research identifies the optimal capacity and efficiency of the spinner machine. Originality: This study provides new insights into the application of spinner machines for CPO extraction, highlighting their potential use in the home industry. Conclusions: The 30 kg capacity was the most effective and efficient for CPO extraction using the home industry spinner machine. Paper Type: Experimental Research Article Keywords: CPO, Extraction, home industry, spinner

Simulation study of a novel methanol production process based on an off-grid Wind/Solar/Oxy-fuel power generation system

Power-to-methanol technology represents a promising energy storage solution to manage the fluctuating supply and demand of renewable energy effectively. A novel methanol production process based on an off-grid wind/solar/Oxy-fuel power plant is presented in the paper, which consists of solar-wind energy, oxy-fuel combined cycle, proton exchange membrane electrolyzer, and carbon dioxide hydrogenation to methanol unit. The hydrogen produced by the proton exchange membrane electrolyzer is used to synthesize methanol, and the by-product oxygen is used in the oxy-fuel combined cycle. At the same time, low-cost carbon capture is achieved with liquefied natural gas cold energy utilization, and the collected carbon dioxide is used to synthesize methanol. The system carbon emission is negative, about −0.344 kg carbon dioxide/kg methanol, the system has no other products except methanol. The structure of renewable energy has a significant impact on the technical and economic performance of the system. Therefore, a comparative analysis of different wind/photovoltaic installed capacity ratios is carried out. The case study shows that the proposed system has the best performance when the wind/photovoltaic installed capacity ratio is 25 %/75 %, with a renewable energy utilization of 97.62 %, methanol production cost of 1.34 $/kg methanol, and an energy efficiency of 63.5 %. The proposed system may be a practical solution for methanol production from renewable energy.

Multilayer Commingled Production Effects in Hydrate Reservoirs with Underlying Gas

Multilayer commingled production is a widely used development method to improve the production capacity of gas reservoirs. However, there is currently limited research on the gas production characteristics of multilayer commingled production in hydrate reservoirs with underlying gas. The objective of this study was to analyze the characteristics of multilayer commingled production in order to determine suitable hydrate reservoirs for such a development method. Firstly, we employed analytical solutions to the equations of fluid flow in porous media to determine the factors affecting the production capacity. Then, by employing numerical simulation and depressurization methods, the rates of gas production and gas release from hydrate dissociation in a single production well were estimated. Additionally, the production capacity ratio of multilayer commingled production and separated-layer production was proposed. The influence of different reservoir characteristics on multilayer commingled production yield was determined and plotted. When there is an interlayer between hydrates and the underlying gas, the formation pressure ratio is the decisive factor affecting the multilayer commingled production yield. When there is no interlayer, the multilayer commingled production rate will increase with an increase in the permeability ratio, hydrate saturation, and underlying gas saturation. This study provides a theoretical foundation for predicting the production capacity of hydrate reservoirs, as well as assistance in selecting the hydrate reservoirs most suitable for multilayer commingled production.

Effect of Resected Lung Volume on Pulmonary Function and Residual Lung Volume in Patients Undergoing Segmentectomy: A Retrospective Study.

We elucidated the effects of planned resection volume on postoperative pulmonary function and changes in residual lung volume during segmentectomy. This study included patients who underwent thoracoscopic segmentectomy between January 2017 and December 2022 and met eligibility criteria. Pre- and post-resection spirometry and computed tomography were performed. Three-dimensional reconstructions were performed by using computed tomography images to calculate the volumes of the resected, remaining, and nonoperative side regions. Based on the resected region volume, patients were divided into the higher and lower volume segmentectomy groups. Changes in lung volume and pulmonary function before and after the surgery were comparatively analyzed. The median percentage of resected lung volume was 10.9%, forming the basis for categorizing patients into the two groups. Postoperative forced expiratory volume in 1 s (FEV1) and forced vital capacity (FVC) ratios to preoperative measurements in both groups did not differ significantly (FEV1, p = 0.254; FVC, p = 0.777). Postoperative FEV1 and FVC ratios to their predicted postoperative values were significantly higher in the higher volume segmentectomy group than in the lower volume segmentectomy group (FEV1, p = 0003; FVC, p < 0.001). The higher volume segmentectomy group showed significantly greater post-to-preoperative lung volume ratio in overall, contralateral, ipsilateral, residual lobe and residual segment than the lower volume segmentectomy group. Postoperative respiratory function did not differ significantly between the higher- and lower-volume segmentectomy groups, indicating improved respiratory function because of substantial postoperative residual lung expansion. Our findings would aid in determining the extent of resection during segmentectomy.