Brush-like Architecture Research Articles

Sustainable chitin-derived elastomers via grafting strategy with tunable mechanical and adhesion properties

With increasing environmental awareness and the pursuit of sustainable development goals, environmentally friendly sustainable thermoplastic elastomers (TPEs) derived from natural resources are highly desired to replace traditional TPEs. However, preparing sustainable TPEs with high mechanical properties and multifunctionality from biobased feedstocks remains a significant challenge. In this work, a series of chitin-graft-poly(acrylamide-co-2-ethylhexyl acrylate) (Chitin-g-P(AM-co-EHA)) copolymers were synthesized through reversible addition-fragmentation chain transfer (RAFT) polymerization. The tensile strength of Chitin-g-P(AM-co-EHA) copolymers can be tuned over a wide range from 1.0 to 7.3 MPa by adjusting the chitin and PAM contents. Benefiting from the brush-like architecture, Chitin-g-P(AM-co-EHA) copolymer exhibits improved mechanical properties over its linear counterparts. Moreover, these Chitin-g-P(AM-co-EHA) copolymers show good adhesion performance on different substrates. The shear strength can achieve 7.5 MPa for Chitin0.8-PAM50, which is high enough for commercial applications. The combination of chitin and grafting strategy can promote the development of strong chitin-based sustainable elastomers. This approach can be further utilized to design novel high-performance biobased elastomers and adhesives derived from natural resources.

Programming and Reprogramming the Viscoelasticity and Magnetic Response of Magnetoactive Thermoplastic Elastomers.

We present a novel type of magnetorheological material that allows one to restructure the magnetic particles inside the finished composite, tuning in situ the viscoelasticity and magnetic response of the material in a wide range using temperature and an applied magnetic field. The polymer medium is an A-g-B bottlebrush graft copolymer with side chains of two types: polydimethylsiloxane and polystyrene. At room temperature, the brush-like architecture provides the tissue mimetic softness and strain stiffening of the elastomeric matrix, which is formed through the aggregation of polystyrene side chains into aggregates that play the role of physical cross-links. The aggregates partially dissociate and the matrix softens at elevated temperatures, allowing for the effective rearrangement of magnetic particles by applying a magnetic field in the desired direction. Magnetoactive thermoplastic elastomers (MATEs) based on A-g-B bottlebrush graft copolymers with different amounts of aggregating side chains filled with different amounts of carbonyl iron microparticles were prepared. The in situ restructuring of magnetic particles in MATEs was shown to significantly alter their viscoelasticity and magnetic response. In particular, the induced anisotropy led to an order-of-magnitude enhancement of the magnetorheological properties of the composites.

Graphene Oxide-Grafted Hybrid Diblock Copolymer Brush (GO-graft-PEG6k-block-P(MA-POSS)) as Nanofillers for Enhanced Lithium Ion Conductivity of PEO-Based Nanocomposite Solid Polymer Electrolytes.

Nanocomposite solid polymer electrolytes (NSPEs) with PEO as the matrix and (i) GO or (ii) GO-graft-PEG6k or (iii) GO-graft-PEG6k-block-P(MA-POSS) as nanofillers have been fabricated to elucidate the impact of the filler morphology on the lithium ion conductivity. GO-graft-PEG6k was obtained by grafting PEG6k onto GO via esterification. GO-graft-PEG6k-block-P(MA-POSS) was prepared via surface-initiated atom transfer radical polymerization. Fourier-transform infrared spectroscopy revealed enhanced salt dissociation and complexation between the filler and PEO host that could be attributed to Lewis acid-base interactions. Electrochemical impedance spectroscopy revealed the improved ion conductivity of the fabricated NSPEs as compared with the pristine PEO-LiClO4. As an example, at 50 °C, the ion conductivity increased to 4.01 × 10-5 and 6.31 × 10-5 S cm-1 with 0.3% GO and 0.3% GO-graft-PEG6k, respectively, from 2.36 × 10-5 S cm-1 of PEO-LiClO4, suggesting that the filler with brush-like architecture (GO-graft-PEG6k) is more efficient in enhancing the ion conductivity. Further increase in filler content resulted in lowering of the ion conductivity that could be ascribed to aggregation of the filler. The most dramatic impact on conductivity was observed with the incorporation of brush-like GO-graft-PEG6k-block-P(MA-POSS) as a nanofiller (3.0 × 10-4 S cm-1 at 50 °C with 1.0 wt % filler content). The increase in ion conductivity in the current systems, as opposed to the conventional view, could not be correlated with the content of the amorphous phase of the matrix. The conduction mechanism is still unclear; nevertheless, it could be assumed that in addition to the ion conduction through the PEO matrix, the filler forms additional low-energy ion conducting channels at its interface with the matrix. The pendent POSS nanocages of GO-graft-PEG6k-block-P(MAPOSS) might probably increase the free volume at the interface with the matrix that is associated with higher chain and ion mobility, thus further enhancing the ion conductivity as compared with GO and GO-graft-PEG6k. The faster ion dynamics in 1.0 wt % GO-graft-PEG6k-block-P(MAPOSS) NSPEs has also been verified by the dielectric relaxation studies. Thus, integration of both the PEG and POSS nanocages into GO-grafted brush-like architecture offers a new tool for tuning the lithium ion conductivity for potential Li ion battery applications.

Nickel nanobrush platform for a magnetic field-assisted electrochemical response enhancement

A single-step electrochemical procedure to synthesize a brush-like platform, which composed of a nickel nanowire array attached to a nickel continuous layer acting as a solid base, is described. Room temperature hysteresis properties of this brush-like architecture (nanobrush) and those of the individual components (nanowires and layer) are determined. It is shown that the direction of the nanobrush magnetic easy axis may be tailored, being also possible to control the magnetic system's coercivity and remanence. The electrochemical response and the catalytic activity of a Ni nanobrush towards the redox probes [Fe(CN) 6 ] 4-/3- and ethanol were evaluated in the presence and absence of an applied magnetic field. The external field strongly affects the system's behavior by enhancing the electrode charge-transfer response, even at fields as low as 6 mT. This improvement was further investigated by Electrochemical Impedance Spectroscopy and Electrochemical Capacitance Spectroscopy studies. It is concluded that the enhanced electrochemical charge-transfer process of the Ni nanobrush electrode, with a magnetic field applied along the Ni nanowires axis, arises from a larger electroactive area. • A Ni nanobrush electrode is obtained by a single step electrodeposition route. • Nanobrush architecture consists of Ni NWs perpendicularly attached to a Ni layer. • The whole platform easy axis orientation is controlled by the brush shape and crystalline texture. • Catalytic activity towards redox probes Fe(CN) 6 −4/−3 and ethanol are evaluated. • A small magnetic field drastically reduces the nanobrush impedance.

Cellulose-Br-Initiated Unique Brush-Like Architectures for Highly Efficient Multifunctional Group Synergistically Regulated Lithium Transfer and Battery Performance of an All-Solid-State Polymer Electrolyte

Cellulose-Br-Initiated Unique Brush-Like Architectures for Highly Efficient Multifunctional Group Synergistically Regulated Lithium Transfer and Battery Performance of an All-Solid-State Polymer Electrolyte

Cellulose Microcrystals with Brush-Like Architectures as Flexible All-Solid-State Polymer Electrolyte for Lithium-Ion Battery

Development of cellulose-based electrolytes can strongly reduce the cost of energy storage devices. However, the prepared cellulose-based electrolytes use high contents of liquid electrolytes, sacr...

Nanoforest: Polyaniline Nanotubes Modified with Carbon Nano-Onions as a Nanocomposite Material for Easy-to-Miniaturize High-Performance Solid-State Supercapacitors.

This article describes a facile low-cost synthesis of polyaniline nanotube (PANINT)–carbon nano-onion (CNO) composites for solid-state supercapacitors. Scanning electron microscopic (SEM) analyses indicate a uniform and ordered composition for the conducting polymer nanotubes immobilized on a thin gold film. The obtained nanocomposites exhibit a brush-like architecture with a specific capacitance of 946 F g−1 at a scan rate of 1 mV s−1. In addition, the nanocomposites offer high conductivity and a porous and well-developed surface area. The PANINT–CNO nanocomposites were tested as electrodes with high potential and long-term stability for use in easy-to-miniaturize high-performance supercapacitor devices.

Molecular Bottlebrushes as Novel Materials.

Molecular bottlebrushes are building blocks for the design of unique polymeric materials whose physical properties are fundamentally governed by their densely grafted structures. Recent developments in the area of reversible deactivation radical polymerization enabled facile and effective control over multiple molecular parameters. Owing to large molecular size, anisotropic conformation, and reduced chain entanglement, molecular bottlebrushes have empowered various applications that are challenging to achieve with linear polymers. In this Review, we focus on determining correlations between brushlike architectures and materials properties.

Self-assembled amphiphilic zein-lactoferrin micelles for tumor targeted co-delivery of rapamycin and wogonin to breast cancer

Protein-based micelles have shown significant potential for tumor-targeted delivery of anti-cancer drugs. In this light, self-assembled nanocarriers based on GRAS (Generally recognized as safe) amphiphilic protein co-polymers were synthesized via carbodiimide coupling reaction. The new nano-platform is composed of the following key components: (i) hydrophobic zein core to encapsulate the hydrophobic drugs rapamycin (RAP) and wogonin (WOG) with high encapsulation efficiency, (ii) hydrophilic lactoferrin (Lf) corona to enhance the tumor targeting, and prolong systemic circulation of the nanocarriers, and (iii) glutaraldehyde (GLA)-crosslinking to reduce the particle size and improve micellar stability. Zein-Lf micelles showed relatively rapid release of WOG followed by slower diffusion of RAP from zein core. This sequential release may aid in efflux pump inhibition by WOG thus sensitizing tumor cells to RAP action. Interestingly, these micelles showed good hemocompatibility as well as enhanced serum stability owing to the brush-like architecture of Lf shell. Moreover, this combined nano-delivery system maximized synergistic cytotoxicity of RAP and WOG in terms of tumor inhibition in MCF-7 breast cancer cells and Ehrlich ascites tumor animal model as a result of enhanced active targeting. Collectively, GLA-crosslinked zein-Lf micelles hold great promise for combined RAP/WOG delivery to breast cancer with reduced drug dose, minimized side effects and maximized anti-tumor efficacy.

Supramolecular Nanostructures of Structurally Defined Graphene Nanoribbons in the Aqueous Phase.

Structurally well-defined graphene nanoribbons (GNRs) have attracted great interest because of their unique optical, electronic, and magnetic properties. However, strong π-π interactions within GNRs result in poor liquid-phase dispersibility, which impedes further investigation of these materials in numerous research areas, including supramolecular self-assembly. Structurally defined GNRs were synthesized by a bottom-up strategy, involving grafting of hydrophilic poly(ethylene oxide) (PEO) chains of different lengths (GNR-PEO). PEO grafting of 42-51 % percent produces GNR-PEO materials with excellent dispersibility in water with high GNR concentrations of up to 0.5 mg mL-1 . The "rod-coil" brush-like architecture of GNR-PEO resulted in 1D hierarchical self-assembly behavior in the aqueous phase, leading to the formation of ultralong nanobelts, or spring-like helices, with tunable mean diameters and pitches. In aqueous dispersions the superstructures absorbed in the near-infrared range, which enabled highly efficient conversion of photon energy into thermal energy.

Hierarchical carbon nanopetal/polypyrrole nanocomposite electrodes with brush-like architecture for supercapacitors.

Hierarchical 3D nanocomposite electrodes with tube brush-like morphology are synthesized by electrochemically depositing polypyrrole (PPY) on carbon nanopetal (CNP) coated carbon fibers (CFs). Initially CNPs are synthesized on CF substrate by chemical vapour deposition. The CNPs synthesized on CF (CNPCF) are further used as an electrically conducting large surface area bearing template for the electropolymerization of PPY in order to fabricate CNPCF-PPY nanocomposite electrodes for supercapacitors (SCs). The CF in CNPCF-PPY nanocomposite functions as (i) a mechanical support for the CNPs, (ii) a current collector for the SC cell and also (iii) to prevent the agglomeration of CNPs within the CNPCF-PPY nanocomposite. Transmission electron microscopy and scanning electron microscopy are used to examine the surface morphology of CNPCF-PPY nanocomposites. The chemical structure of the nanocomposites is analysed by Fourier transform infrared spectroscopy. X-Ray photoelectron spectroscopy has been used to understand the chemical bonding states of the hierarchical CNPCF-PPY nanocomposites. The electrochemical properties of symmetric type CNPCF-PPY SC cells are examined by electrochemical impedance spectroscopy, cyclic voltammetry and galvanostatic charge-discharge measurements. The hierarchical CNPCF-PPY SC exhibits a maximum gravimetric capacitance of 280.4 F g(-1) and an area specific capacitance of 210.3 mF cm(-2) at a current density of 0.42 mA cm(-2). The CNPCF-PPY SC cell exhibits good cycling stability of more than 5000 cycles. The present study proclaims the development of a novel lightweight SC with high-performance.

Solvent-free, supersoft and superelastic bottlebrush melts and networks.

Polymer gels are the only viable class of synthetic materials with a Young's modulus below 100 kPa conforming to biological applications, yet those gel properties require a solvent fraction. The presence of a solvent can lead to phase separation, evaporation and leakage on deformation, diminishing gel elasticity and eliciting inflammatory responses in any surrounding tissues. Here, we report solvent-free, supersoft and superelastic polymer melts and networks prepared from bottlebrush macromolecules. The brush-like architecture expands the diameter of the polymer chains, diluting their entanglements without markedly increasing stiffness. This adjustable interplay between chain diameter and stiffness makes it possible to tailor the network's elastic modulus and extensibility without the complications associated with a swollen gel. The bottlebrush melts and elastomers exhibit an unprecedented combination of low modulus (∼100 Pa), high strain at break (∼1,000%), and extraordinary elasticity, properties that are on par with those of designer gels.

Polymer-nanocomposite brush-like architectures as an all-solid electrolyte matrix.

Herein, we report on polymer-nanocomposites with brush-like architectures and evaluate their feasibility as an all-solid electrolyte matrix supporting Li(+)-ion conduction. Showcased as a first example in the domain of electrolyte research, the study probes several key factors, such as (i) core morphology, (ii) surface modifiers/functionality, (iii) grafting length, and (iv) density of the brushes, and determines their role on the overall electrochemical properties of these nanostructured organic-inorganic hybrids. Nanostructured titania was synthesized via wet-chemical approaches using either controlled hydrolysis or hydrothermal methods. Exercising suitable control on reaction parameters led to well-defined morphologies/phases, such as nanoparticles, nanospindles, nanourchins, nanorods or nanotubes, in either anatase, rutile or mixed forms. Covalent anchoring on titania nanostructures was achieved using dopamine, gallic acid and glycerol as small organic moieties. A one-pot process of priming the available surface functional groups postmodification with isocyanate chemistry was followed by grafting polyethylene glycol monomethyl ethers of desired chain lengths. Finally, complexation with lithium salt yielded electrolyte compositions where the ethylene oxide (EO) fractions aid in ion-solvation with ease. The synthesized materials were characterized in detail employing XRD, TEM, DRS-UV, FTIR, micro-Raman, TG-DTA and DSC at each stage to confirm the products and ascertain the physicochemical properties. Comprehensive evaluation using temperature-step electrochemical impedance spectroscopy (EIS) of these brush-like nanocomposites provided crucial leads toward establishing a plausible physical model for the system and understanding the mechanism of ion transport in these all-solid matrices. The preliminary results on ionic conductivity (σ) obtained for some of the compositions are estimated to be within the range of ∼10(-4) to 10(-5) S cm(-1) in the temperature window of the study that holds excellent promise for further improvement.

Highly Efficient Phase Boundary Biocatalysis with Enzymogel Nanoparticles

The enzymogel nanoparticle made of a magnetic core and polymer brush shell demonstrates a novel type of remote controlled phase-boundary biocatalysis that involves remotely directed binding to and engulfing insoluble substrates, high mobility, and stability of the catalytic centers. The mobile enzymes reside in the polymer brush scaffold and shuttle between the enzymogel interior and surface of the engulfed substrate in the bioconversion process. Biocatalytic activity of the mobile enzymes is preserved in the enzymogel while the brush-like architecture favors the efficient interfacial interaction when the enzymogel spreads over the substrate and extends substantially the reaction area as compared with rigid particles.

A versatile method for functionalization and grafting of 2-hydroxyethyl cellulose (HEC) via Click chemistry

This article describes a versatile method for the modification of 2-hydroxyethyl cellulose (HEC) involving azide-alkyne cycloaddition reaction to impart neutral (ester) and ionic (carboxylic acid and 1ry amine) functionalities. The synthetic approach involved, first the introduction of the azide functionality to HEC and then followed by its cycloaddition reaction with several alkyne terminated compounds: namely ethyl propiolate, 5-hexynoic acid and propargyl amine. Sequential Click reactions were also demonstrated to be feasible by the successful synthesis of polydimethylsiloxane (PDMS) grafted HEC containing neutral (ester) and ionic (carboxylic acid and 1ry amine) functionalities. The Click chemistry was then further utilized similarly to graft poly(lactic acid) (PLA) and poly(ethylene glycol) (PEG) segments to HEC to access its hydrophobic and hydrophilic analogs, respectively. AFM analysis revealed that while HEC itself formed uniform oval features, the PLA grafted HEC exhibited a brushlike architecture. The formation of these brushlike structures suggested that the HEC backbone exhibits an extended conformation with the side chains stretched out. The resulting polymeric materials were characterized by solution and solid state 13C NMR and FTIR spectroscopy.

A versatile single‐electron‐transfer mediated living radical polymerization route to galactoglucomannan graft‐copolymers with tunable hydrophilicity

AbstractCu(0) mediated living radical polymerization was successfully applied to synthesize graft‐copolymers from the hemicellulose acetylated galactoglucomannan. Functionalizing the polysaccharide backbone with α‐bromo isobutyric acid gave rise to a macroinitiator for single‐electron‐transfer mediated living radical polymerization (SET‐LRP). This macroinitiator with a degree of substitution of 0.15 or 0.20 was used in the graft‐SET‐LRP of methyl methacrylate in dimethyl sulfoxide as well as N‐isopropyl acrylamide and acrylamide in water. Kinetic analyses confirm conversions of up to 73% and a controlled behavior of the SET‐LRP process providing high molecular weight hemicellulose‐based hybrid copolymers with a brush‐like architecture. Derived graft‐copolymers varied significantly in solubility properties, ranging from hydrophobic via temperature responsive water‐solubility to water‐soluble. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011

Hemicellulose-Based Multifunctional Macroinitiator for Single-Electron-Transfer Mediated Living Radical Polymerization

A multifunctional macroinitiator for single-electron-transfer mediated living radical polymerization (SET-LRP) was designed from acetylated galactoglucomannan (AcGGM) by α-bromoisobutyric acid functionalization of the anomeric hydroxyl groups on the heteropolysaccharide backbone. This macroinitiator, with a degree of substitution of 0.15, was used in the SET-LRP of methyl acrylate, catalyzed by Cu(0)/Me(6)-TREN in DMSO, DMF, or DMSO/H(2)O in various concentrations. Kinetic analyses confirm high conversions of up to 99.98% and a living behavior of the SET-LRP process providing high molecular weight hemicelluloses/methyl acrylate hybrid copolymers with a brush-like architecture.

Tension amplification in molecular brushes in solutions and on substrates.

Molecular bottle-brushes are highly branched macromolecules with side chains densely grafted to a long polymer backbone. The brush-like architecture allows focusing of the side-chain tension to the backbone and its amplification from the pico-Newton to nano-Newton range. The backbone tension depends on the overall molecular conformation and the surrounding environment. Here we study the relation between the tension and conformation of the molecular brushes in solutions, melts, and on substrates. In solutions, we find that the backbone tension in dense brushes with side chains attached to every backbone monomer is on the order of f(0)N(3/8) in athermal solvents, f(0)N(1/3) in theta solvents, and f(0) in poor solvents and melts, where N is the degree of polymerization of side chains, f(0) approximately equal k(B)T/b is the maximum tension in side chains, b is the Kuhn length, k(B) is Boltzmann's constant, and T is the absolute temperature. Depending on the side chain length and solvent quality, molecular brushes develop tension on the order of 10-100 pN, which is sufficient to break hydrogen bonds. Significant amplification of tension occurs upon adsorption of brushes onto a substrate. On a strongly attractive substrate, maximum tension in the brush backbone is approximately f(0)N, reaching values on the order of several nano-Newtons, which exceeds the strength of a typical covalent bond. At low grafting density and high spreading parameter, the cross-sectional profile of an adsorbed molecular brush is approximately rectangular with a thickness approximately b (A/S)1/2, where A is the Hamaker constant, and S is the spreading parameter. At a very high spreading parameter (S > A), the brush thickness saturates at monolayer approximately b. At a low spreading parameter, the cross-sectional profile of adsorbed molecular brush has a triangular tent-like shape. In the cross-over between these two opposite cases, covering a wide range of parameter space, the adsorbed molecular brush consists of two layers. Side chains in the lower layer gain surface energy due to the direct interaction with the substrate, while the second layer spreads on the top of the first layer. Scaling theory predicts that this second layer has a triangular cross-section with width R approximately N(3/5) and height h approximately N(2/5). Using self-consistent field theory we calculate the cap profile y(x) = h(1 - x2/R2)2, where x is the transverse distance from the backbone. The predicted cap shape is in excellent agreement with both computer simulation and experiment.

Polymersomes: A new multi-functional tool for cancer diagnosis and therapy

Nanoparticles are being developed as delivery vehicles for therapeutic pharmaceuticals and contrast imaging agents. Polymersomes (mesoscopic polymer vesicles) possess a number of attractive biomaterial properties that make them ideal for these applications. Synthetic control over block copolymer chemistry enables tunable design of polymersome material properties. The polymersome architecture, with its large hydrophilic reservoir and its thick hydrophobic lamellar membrane, provides significant storage capacity for both water soluble and insoluble substances (such as drugs and imaging probes). Further, the brush-like architecture of the polymersome outer shell can potentially increase biocompatibility and blood circulation times. A further recent advance is the development of multi-functional polymersomes that carry pharmaceuticals and imaging agents simultaneously. The ability to conjugate biologically active ligands to the brush surface provides a further means for targeted therapy and imaging. Hence, polymersomes hold enormous potential as nanostructured biomaterials for future in vivo drug delivery and diagnostic imaging applications.

Synthesis and characterization of biodegradable polylactide-grafted dextran and its application as compatilizer

Brush-like biodegradable polylactide-grafted dextran copolymer (PLA-g-dextran) was by a bulk polymerization reaction using a trimethylsilyl-protected (TMS) dextran as macroinitiator and stannous octoate as catalyst. After the polymerization, the TMS groups could be easily removed by immersing the copolymer in methanol for 48 h. The PLA-g-dextran copolymers were characterized by 1H NMR, GPC and intrinsic viscosity measurements. Besides, mouse 3T3 fibroblasts were cultured on these copolymeric substrates together with pure polylactide (PLA). Although the copolymers exhibited better hydrophilicity and cell affinity compared to pure PLA because of the incorporation of glucose units and the brush-like architecture, it was found that the cells still could not migrate into the center part of scaffold made of PLA-g-dextran copolymer. In result, PLA-g-dextran copolymers themselves were not an appropriate choice for the cell scaffold material, however, it could be used as compatilizer to ameliorate the compatibility between hydrophilic dextran and hydrophobic PLA due to its amphiphilic structure, which could improve the mechanical properties of PLA/dextran blends by reducing the phase separation between PLA and dextran. Therefore, the PLA/dextran blends, which had good cell affinity and moderate mechanical strength, might be prospect cell scaffold materials.