Broadband Optical Absorption Research Articles

Janus aramid nanofiber aerogel incorporating plasmonic nanoparticles for high-efficiency interfacial solar steam generation

Interfacial solar steam generation (ISSG) is a novel and potential solution to global freshwater crisis. Here, based on a facile sol-gel fabrication process, we demonstrate a highly scalable Janus aramid nanofiber aerogel (JANA) as a high-efficiency ISSG device. JANA performs near-perfect broadband optical absorption, rapid photothermal conversion and effective water transportation. Owning to these features, efficient desalination of salty water and purification of municipal sewage are successfully demonstrated using JANA. In addition, benefiting from the mechanical property and chemical stability of constituent aramid nanofibers, JANA not only possess outstanding flexibility and fire-resistance properties, but its solar steaming efficiency is also free from the influences of elastic deformations and fire treatments. We envision JANA provides a promising platform for mass-production of high-efficiency ISSG devices with supplementary capabilities of convenient transportation and long-term storage, which could further promote the realistic applications of ISSG technology.

Transition-metal ions in β-Ga2O3 crystals: Identification of Ni acceptors

Transition-metal ions (Ni, Cu, and Zn) in β-Ga2O3 crystals form deep acceptor levels in the lower half of the bandgap. In the present study, we characterize the Ni acceptors in a Czochralski-grown crystal and find that their (0/−) level is approximately 1.40 eV above the maximum of the valence band. Both Ni2+ (3d8) and Ni3+ (3d7) acceptors are present in the as-grown crystal. Also present are unintentional Ir3+ (5d6) and Ir4+ (5d5) donors. The neutral Ni3+ acceptors have a low-spin S = 1/2 ground state and are easily monitored with electron paramagnetic resonance (EPR). Principal values of the g matrix for these acceptors are 2.131, 2.138, and 2.233. Although paramagnetic, the singly ionized Ni2+ acceptors are not seen with EPR at X band (9.4 GHz). The Ir4+ donors are monitored with EPR and with infrared absorption spectroscopy. Exposing the Ni-doped β-Ga2O3 crystal to 275 nm light at room temperature increases the concentration of Ni3+ ions and reduces the concentration of Ir4+ ions as electrons move from the acceptors to the donors. After illumination, heating the crystal above 375 °C restores the initial concentrations of the Ni3+ and Ir4+ ions. Broad optical absorption bands peaking near 303 and 442 nm are attributed to the Ni3+ acceptors.

Broadband optical absorption and photothermal properties of partially disordered MoSe2 nanospheres

The new broadband light-absorbing material is essential for effective utilization of solar energy. However, the size-controllable MoSe2 nanospheres for the applications in broadband light-absorbing and photothermal fields, as well as the role of partially disordered features on the optical responses have not been well investigated. Here, we prepare the partially disordered MoSe2 nanospheres by a facile solvothermal synthesis method and investigate the random impacts of the spherical diameter on optical responses. The MoSe2 nanospheres reveal dark black color and broadband absorption from ultraviolet to near-infrared wavelength without obvious absorption edge. The photothermal properties with super-continuous laser irradiation demonstrate that MoSe2 nanospheres have high photothermal conversion efficiency of about 44.8% in water and even also reach about 30.7% in ethanol. The superior light absorption could originate from free-carriers absorption, defective state absorption and resonant absorption. The results not only pave the way of two-dimensional material for disordered photonic researches, but also widen the potential applications of MoSe2 in saturable absorber and photothermal agent.

(Invited) Broadband and Broad Angle Enhanced Light Absorption in MoS2 based Hetero Plasmonic Structure

Solar cells, photovoltaic devices and optoelectronic elements needs enhanced light absorption with a wide range of incident angle for better and efficient design. Two-dimensional (2D) materials have exceled in all areas including electrical applications, optical modulations, mechanical as well as chemical implementations due to their direct bandgap and high optical absorption nature[1]. Photon irradiation allows to generate electron-hole pairs in a direct bandgap material such as TMDCs which makes them potential candidates for large amount of light to be trapped. Different structures have been studied to achieve high optical absorption [2][3]. Although one dimensional photonic crystal(1DPC) and defective PC has good optical absorption with wide range and angle [4],[2] number of layers and complexity in structure has made it difficult to be fabricated. MoS2 monolayer structure based on cover spacer, plasmonic and dual substrate layer (SiO2(50nm)/Si ) has also increased optical absorption range and broad angle [5] but TMDC based heterostructures with spacer has improved absorption comparing to previous structures without metallic layer [6]. In this paper, we proposed a dual TMDC-spacer based plasmonic structure with dual substrate for wide and broad range and angle of near perfect optical absorption.The structure considered here is an air/MoS2/Spacer1/MoS2/Spacer2/plasmonic/dual substrate with 0.665nm, 70nm and 50nm layer of MoS2, Au as plasmonic layer and SiO2 as part of dual layer with Si as lossless substate. (Figure 1) For spacers SiO2 and TiO2 are taken with optimized value (figure 2) of 92 and 68nm for enhanced absorption. The transfer matrix of the constituted layer for either transverse electric (TE) or transverse magnetic (TM) polarization was determined using the transfer matrix method (TMM). Both in TE and TM mode, the ~30 and ~40% of enhanced light absorption are observed in proposed structure compared to hetero and mono layer structure (figure 3) with impact of metallic and spacer layer. In case of incident angle, both at resonance frequency of MoS2 and within visible range, broad angle range (00-400 for TE and 00-800 for TM) is observed with wider wavelength. (Figure 4 and figure 5). Impact of various metallic layer on the proposed structure is also observed (Figure 6). Structure with VO2 as plasmonic layer [7] has around ~95% of peak absorption (400nm-550nm) and wide incident angle (00-850) irrespective of polarizations with lieu of spacer hetero-TMDC-stack (Figure 7). Due to multiple layers of structures, collective surface plasmon polaritons (SPP) has an enhanced light absorption within the heterostructure and enhanced electric field distribution of the structure is observed (Figure 8).Table I lists some comparison among various structures and parameters indicates that proposed dual spacer -TMDC based plasmonic heterostructure has wide visible range of wavelength (400-550 nm) with broad angle (00-850) light absorption with both polarizations compare to other counterparts.In this work an enhanced range in both wavelength and incident angle of visible optical absorption is observed in both polarization with plasmonic dual heterostructure is observed and compared with other structures. Such structures are useful for photodetectors and solar cells for maximum absorptions.[1] Lopez-Sanchez O, Lembke D, Kayci M, Radenovic A and Kis A 2013 Ultrasensitive photodetectors based on monolayer MoS 2 Nat. Nanotechnol. 8 497–501[2] Ansari N and Mohebbi E 2018 Broadband and high absorption in Fibonacci photonic crystal including MoS2 monolayer in the visible range J. Phys. D. Appl. Phys. 51 149–52[3] Ansari N and Ghorbani F 2018 Light absorption optimization in two-dimensional transition metal dichalcogenide van der Waals heterostructures J. Opt. Soc. Am. B 35 1179[4] Ansari N and Mohebbi E 2016 Increasing optical absorption in one-dimensional photonic crystals including MoS2 monolayer for photovoltaics applications Opt. Mater. (Amst). 62 152–8[5] Ansari N, Mohebbi E and Gholami F 2020 Nearly perfect and broadband optical absorption by TMDCs in cover/TMDC/spacer/Au/substrate multilayers Appl. Phys. B Lasers Opt. 126 1–6[6] Ansari N, Goudarzi B and Mohebbi E 2021 Design of narrowband or broadband absorber by heterostructures including TMDCs and spacers Opt. Laser Technol. 138 106771[7] Das H R and Arya S C 2021 Performance improvement of VO2 and ITO based plasmonic electro-absorption modulators at 1550 nm application wavelength Opt. Commun. 479 Figure 1

The Broad Band Optical Absorber Designed By Multilayered Hyperbolic Metamaterial

Bu çalışmada, özellikle optik bölgede geniş band soğurma gösteren çok tabakalı bir hiperbolik metamalzeme tasarlanmıştır. Tasarlanan yapıda üç farklı metal (Ag, Au ve Al) ve yarıiletken bir malzeme (InGaAs) kullanılmıştır. Hesaplamalarda Transfer Matris Metodundan (TMM) yararlanılmıştır. Bu yöntem kullanılarak tasarlanan çok tabakalı yapıların optik soğurma ve yansıma spektrumları gelme açısına bağlı olarak incelenmiştir. Metal-dielektrik çok tabakalı yapıların hiperbolik dispersiyon gösterdiği bölgeler belirlenmiş, ayrıca gelme açısına bağlı kontur grafikleri elde edilmiştir. Yapılan hesaplamalar sonucunda, metal olarak gümüşün kullanıldığı heteroyapının en iyi soğurma spektrumu verdiği gözlenmiştir.

Ultrafast nano generation of acoustic waves in water via a single carbon nanotube

Generation of ultra high frequency acoustic waves in water is key to nano resolution sensing, acoustic imaging and theranostics. In this context water immersed carbon nanotubes (CNTs) may act as an ideal optoacoustic source, due to their nanometric radial dimensions, peculiar thermal properties and broad band optical absorption. The generation mechanism of acoustic waves in water, upon excitation of both a single-wall (SW) and a multi-wall (MW) CNT with laser pulses of temporal width ranging from 5 ns down to ps, is theoretically investigated via a multiscale approach. We show that, depending on the combination of CNT size and laser pulse duration, the CNT can act as a thermophone or a mechanophone. As a thermophone, the CNT acts as a nanoheater for the surrounding water, which, upon thermal expansion, launches the pressure wave. As a mechanophone, the CNT acts as a nanopiston, its thermal expansion directly triggering the pressure wave in water. Activation of the mechanophone effect is sought to trigger few nanometers wavelength sound waves in water, matching the CNT acoustic frequencies. This is at variance with respect to the commonly addressed case of water-immersed single metallic nano-objects excited with ns laser pulses, where only the thermophone effect significantly contributes. The present findings might be of impact in fields ranging from nanoscale non-destructive testing to water dynamics at the meso to nanoscale.

Identification of aggregated 2D cobalt tellurides using a spatial self-phase modulation technique.

We report a previously unreported application of the spatial self-phase modulation (SSPM) technique for recognizing solute-solvent interaction in a suspension of 2D material. Broadband optical absorption of the 2D Co2Te3 leads to a nonlinear optical (NLO) susceptibility for the monolayer, i.e., χ M o n o(3) of 1.5 ×10-9 (3.3 ×10-9) esu at 532 (632) nm, which is 1-2 orders higher than for the 2D CoTe and CoTe2. The fine structure of the SSPM patterns is analyzed to explore the foundations of the observed NLO effects. With increasing polarity of the liquid media, a change of 2D Co2Te3 from homophonous dispersion to aggregation occurs, as confirmed from in situ optical microscopy and UV-vis absorption spectroscopy. As a result, type-I (thickest outer ring) SSPM ring patterns are converted to type-II (thinnest outer ring) SSPM ring patterns. Therefore, using SSPM with a CW laser as an optical tool to identify solvent-polarity-induced aggregation in 2D materials is possible.

Super broadband mid-infrared absorbers with ultrathin folded highly-lossy films

Super broadband optical absorbers with ultrathin films have been keenly pursued for a long time. Although highly lossy materials with sharp light attenuation have the potential to become super absorbers, a large percent of light from free space is inevitably reflected back for the distinct impedance mismatch. Here, a simple strategy, of which reducing the thickness of highly-lossy thin films to minish reflectance and simultaneously folding the ultrathin films to make light multiple pass through, is proposed to obtain super broadband mid-infrared absorbers with ultrathin films. Along this line, the absorbers were prepared by depositing Al-doped ZnO film on scaffolds consisted of alumina spherical shells, whose substrates were opaque. When the thickness of Al-doped ZnO is 43 nm and the layer number of scaffolds is three, a maximum average absorptance was achieved as 97.6% over the wavelength range from 3 to 15 μm. Applying this strategy on polished Al foil, excellent infrared camouflage performance on human-body background was demonstrated. Featured by the strong broadband optical absorption with ultrathin films, flexible access to multiple substrates and low-cost procedures, this approach has the potential in widespread applications of infrared thermal emitters and optoelectronic devices.

Photocatalytic β-In2S3 nanoflowers synthesized by thermal assembly of In2S3 nanosheets

Three-dimensional (3D) β-In2S3 offers photocatalytic advantages by virtue of its strong and broadband optical absorption resulting from its large effective surface area and a high density of sulfur vacancies. However, the use of surfactants and reducing agents complicates the synthesis process and causes undesirable agglomeration while forming the 3D structures, degrading the photocatalytic efficiency of 3D In2S3. Here we have prepared the surfactant-free In2S3 nanoflowers by the thermal assembly of two-dimensional (2D) In2S3 nanosheets and achieved a substantial enhancement of the optical absorption and the tunable bandgap narrowing. We show that owing to the intrinsic structure of our In2S3 nanoflowers that preserves the unit geometry of 2D In2S3 nanosheets, the rate of photocatalytic performance was enhanced by 200% just by the post-annealing process. The facile method used to prepare In2S3 nanoflowers expedites the practical application of 3D In2S3 for energy and environmental purposes.

High conductivity Sepia melanin ink films for environmentally benign printed electronics

Melanins (from the Greek μέλας, mélas, black) are bio-pigments ubiquitous in flora and fauna. Eumelanin is an insoluble brown-black type of melanin, found in vertebrates and invertebrates alike, among which Sepia (cuttlefish) is noteworthy. Sepia melanin is a type of bio-sourced eumelanin that can readily be extracted from the ink sac of cuttlefish. Eumelanin features broadband optical absorption, metal-binding affinity and antioxidative and radical-scavenging properties. It is a prototype of benign material for sustainable organic electronics technologies. Here, we report on an electronic conductivity as high as 10-3 S cm-1 in flexographically printed Sepia melanin films; such values for the conductivity are typical for well-established high-performance organic electronic polymers but quite uncommon for bio-sourced organic materials. Our studies show the potential of bio-sourced materials for emerging electronic technologies with low human- and eco-toxicity.

Efficient Photocatalytic Oxidative Coupling of Benzylamine over Uranyl-Organic Frameworks.

Visible-light-driven organic transformation photocatalyzed by metal-organic frameworks (MOFs) under mild conditions is considered a feasible route to conserve energy and simplify synthesis. Herein, a light-sensitized, three-dimensional uranyl-organic framework (HNU-64) with twofold interpenetration and its derivatives HNU-64-CH3 and HNU-64-Cl with functionalized ligands of -CH3 and -Cl groups were obtained. These MOFs have broad optical absorption bands and suitable band energy levels in photooxidation, which makes them exhibit high activity and selectivity for the photooxidation of benzylamine to N-benzylbenzoimide under mild conditions. This work provides an efficient and simple synthetic option for oxidative coupling of amines to directly produce imines.

Graphene Metamaterial Embedded within Bundt Optenna for Ultra-Broadband Infrared Enhanced Absorption.

Graphene is well-known for its extraordinary physical properties such as broadband optical absorption, high electron mobility, and electrical conductivity. All of these make it an excellent candidate for several infrared applications such as photodetection, optical modulation, and optical sensing. However, a standalone monolayer graphene still suffers from a weak infrared absorption, which is ≅2.3%. In this work, a novel configuration of graphene metamaterial embedded inside Bundt optical-antenna (optenna) is demonstrated. It can leverage the graphene absorption up to 57.7% over an ultra-wide wavelength range from 1.26 to 1.68 µm (i.e., Bandwidth ≅ 420 nm). This range covers the entire optical communication bands of O, E, S, C, L, and U. The configuration mainly consists of a Bundt-shaped plasmonic antenna with a graphene metamaterial stack embedded within its nano-wide waveguide that has a 1.5 µm length. The gold average plasmonic loss is ≅25%. This configuration can enhance graphene ultra-broadband absorption through multiple mechanisms. It can nano-focus the infrared radiation down to a 50 nm spot on the graphene metamaterial, thus yielding an 11.5 gain in optical intensity (i.e., 10.6 dB). The metamaterial itself has seven concentric cylindrical graphene layers separated by silicon dioxide thin films, thus each layer contributes to the overall absorption. The focused infrared propagates tangential to the graphene metamaterial layers (i.e., grazing propagation), and thus maximizes the light–graphene interaction length. In addition, each graphene layer experiences a double-face exposure to the nano-focused propagating spot, which increases each layer’s absorption. This configuration is compact and polarization-insensitive. The estimated maximum absorption enhancement compared to the standalone monolayer graphene was 25.1 times (i.e., ≅4 dB). The estimated maximum absorption coefficient of the graphene stack was 5700 cm−1, which is considered as one of the record-high reported coefficients up to date.

Broadband saturable absorption in germanene for mode-locked Yb, Er, and Tm fiber lasers

Abstract Passively mode-locked lasers have been widely investigated as one of the effective methods to obtain ultrashort pulses. As an important part of passively mode-locked fiber lasers, the exploration of 2D material-based saturable absorber has become one of the hotspots in ultrafast photonics in recent years. Germanene, a novel 2D Dirac material, with ultrafast optical response and broadband optical absorption, is a promising alternative material for saturable absorber in mode-locked fiber lasers. In this paper, germanium nanosheets are prepared via liquid-phase exfoliated method, with the saturable absorption property systematically characterized in three major wavebands of the near-infrared region. The generation of ultrashort pulses based on germanene saturable absorber in fiber lasers is further realized, in a broad waveband (1000 nm) centered at 1061.1, 1559.3 and 1883.5 nm, respectively. In addition, noise-like pulses operation with central wavelength of 1558.6 nm is also obtained, and the formation of rogue waves is further demonstrated via statistical analysis. To the best of our knowledge, this is the first experimental verification of the broadband saturable absorption property of germanene-based devices, covering three major fiber laser wavelengths from 1.0 to 2.0 μm.

Possible catalytic activity of N,N-coordinated mono-cationic copper bound Pyrazol-1-yl(1H-pyrrol-2-yl)methanone complex: a computational study

Organic ligand-based transition metal coordinated complexes have been of paramount importance. They have found a lot of utilities in catalysis, bond activation, dye-sensitized solar cells, etc. Focusing on the so-called noble metal or coinage metal and keeping in mind the inexpensive single metal atom based catalyst, copper bound complexes are considered for adsorption of gas molecules and bond activation therein. Here, we have studied the interaction between a [Cu–NN] complex (N,N-coordinated mono-cationic copper bound Pyrazol-1-yl(1H-pyrrol-2-yl)methanone) and different gas molecules as ligands, such as L = H2, N2, CO, H2O, C2H4 and C2H2, which are industrially and environmentally important. Our computational investigation infers that these ligands are effective in electronic interactions and optical properties of the complex. The stability, geometry and the bonding nature in L bound [Cu–NN] complexes are studied to check their viability at room temperature. The [Cu–NN] complex can bind small gas molecules as ligands, viz., H2, N2, CO, H2O, C2H4 and C2H2, in a thermodynamically favorable way and the complexation induces bond activation within the ligands in the bound state as compared to their free state. All the [L–Cu–NN] complexes along with the bare complex show broadband optical absorption in the ultraviolet–visible (UV–Vis) domains. Furthermore, selective ligand binding has modulated the Fermi energy level resulting in an enhanced chemical reactivity of the [Cu–NN] complex.

Investigation of broad-band optical absorption and electrical properties in vacuum annealed CZTS/Ag multi-layered stack structure for plasmonic solar cell application

As there is only a few research work carried out in thin film plasmonic Cu2ZnSnS4 (CZTS) based solar cells, it is exceedingly inspiring to advance the optical and electrical properties through incorporating Ag nanoparticles without affecting its structural properties. In this work, CZTS and Ag were stacked with the help of sequential magnetron sputtering method using RF and DC power supplies. Homogeneous distribution of Ag nanoparticles in CZTS matrix has been achieved via post deposition annealing at 500 °C. The concentration of Ag has been tailored by varying deposition time from 30 to 90 s. The morphological properties of Ag incorporated CZTS thin films has been investigated by using FE-SEM technique. The optical property of CZTS films has been enhanced by increasing the optical path length through multiple scattering due to the localized surface plasmon resonance (LSPR) of Ag nanoparticles. In Hall effect study, a gradual drop in the resistivity is observed with increasing Ag deposition time however it is within the tolerable limit of CZTS film.

Self-Driven Broadband Photodetectors Based on MoSe2/FePS3 van der Waals n-p Type-II Heterostructures.

Two-dimensional (2D) van der Waals materials with broadband optical absorption are promising candidates for next-generation UV-vis-NIR photodetectors. FePS3, one of the emerging antiferromagnetic van der Waals materials with a wide bandgap and p-type conductivity, has been reported as an excellent candidate for UV optoelectronics. However, a high sensitivity photodetector with a self-driven mode based on FePS3 has not yet been realized. Here, we report a high-performance and self-powered photodetector based on a multilayer MoSe2/FePS3 type-II n-p heterojunction with a working range from 350 to 900 nm. The presented photodetector operates at zero bias and at room temperature under ambient conditions. It exhibits a maximum responsivity (Rmax) of 52 mA W-1 and an external quantum efficiency (EQEmax) of 12% at 522 nm, which are better than the characteristics of its individual constituents and many other photodetectors made of 2D heterostructures. The high performance of MoSe2/FePS3 is attributed to the built-in electric field in the MoSe2/FePS3 n-p junction. Our approach provides a promising platform for broadband self-driven photodetector applications.

Cu2+ and Cu3+ acceptors in β-Ga2O3 crystals: A magnetic resonance and optical absorption study

Electron paramagnetic resonance (EPR) and optical absorption are used to characterize Cu2+ (3d9) and Cu3+ (3d8) ions in Cu-doped β-Ga2O3. These Cu ions are singly ionized acceptors and neutral acceptors, respectively (in semiconductor notation, they are Cu− and Cu0 acceptors). Two distinct Cu2+ EPR spectra are observed in the as-grown crystals. We refer to them as Cu2+(A) and Cu2+(B). Spin-Hamiltonian parameters (a g matrix and a 63,65Cu hyperfine matrix) are obtained from the angular dependence of each spectrum. Additional electron-nuclear double resonance (ENDOR) experiments on Cu2+(A) ions give refined 63Cu and 65Cu hyperfine matrices and provide information about the nuclear electric quadrupole interactions. Our EPR results show that the Cu2+(A) ions occupy octahedral Ga sites with no nearby defect. The Cu2+(B) ions, also at octahedral Ga sites, have an adjacent defect, possibly an OH− ion, an oxygen vacancy, or an H− ion trapped within an oxygen vacancy. Exposing the crystals at room temperature to 275 nm light produces Cu3+ ions and reduces the number of Cu2+(A) and Cu2+(B) ions. The Cu3+ ions have an S = 1 EPR spectrum and are responsible for broad optical absorption bands peaking near 365, 422, 486, 599, and 696 nm. An analysis of loops observed in the Cu3+ EPR angular dependence gives 2.086 for the g value and 22.18, 3.31, and −25.49 GHz for the principal values of D (the fine-structure matrix). Thermal anneal studies above room temperature show that the Cu3+ ions decay and the Cu2+ ions recover between 75 and 375 °C.

Preparation and Bolometric Responses of MoS2 Nanoflowers and Multi-Walled Carbon Nanotube Composite Network.

Due to their broadband optical absorption ability and fast response times, carbon nanotube (CNT)-based materials are considered promising alternatives to the toxic compounds used in commercial infrared sensors. However, the direct use of pure CNT networks as infrared sensors for simple resistance read-outs results in low sensitivity values. In this work, MoS2 nanoflowers are composited with CNT networks via a facile hydrothermal process to increase the bolometric performance. The thermal diffusivity (α) against temperature (T) is measured using the transient electro-thermal (TET) technique in the range of 320 K to 296 K. The α-T curve demonstrates that the composite containing MoS2 nanoflowers provides significant phonon scattering and affects the intertube interfaces, decreasing the α value by 51%. As the temperature increases from 296 K to 320 K, the relative temperature coefficient of resistance (TCR) increases from 0.04%/K to 0.25%/K. Combined with the enhanced light absorption and strong anisotropic structure, this CNT–MoS2 composite network exhibits a more than 5-fold greater surface temperature increase under the same laser irradiation. It shows up to 18-fold enhancements in resistive responsivity ((Ron − Roff)/Roff) compared with the pure CNT network for a 1550 nm laser at room temperature (RT).

Photon Recycling Effect and Lossless Fluorescence Propagation in β‐Sheet Peptide Fibers

AbstractLight‐delivering optical fibers are widely used for biomedical imaging, theranostics and surgery, and optogenetics. In this work, a new generation of bioinspired optical fibers is proposed. Developed amyloidogenic peptide fibrillary structures with tailored β‐sheet conformation exhibit unique optical properties of full overlapping of broadband visible fluorescence (FL) and optical absorption spectra. This study reports on unexpected lossless propagation of the FL light along 100 µm length β‐sheet microfibers. It is shown that the found FL long‐distance lossless radiative energy transport occurs due to highly effective FL photon recycling phenomenon supported by FL zero Stokes shift and high quantum yield. This new non‐Beer–Lambert FL lossless propagation mechanism is observed in very thin ≈1 µm diameter fibers, providing a single/few‐mode waveguiding regime. The developed model and computer simulations, based on the finite difference time domain method, are consistent with the experimental results. Fabricated peptide FL fiber probes permit delivering intensity‐modulated FL signal with selected wavelength over the whole visible spectrum in wide modulation frequencies range.

High-Entropy-Alloy Nanoparticles with Enhanced Interband Transitions for Efficient Photothermal Conversion.

Photothermal materials with broadband optical absorption and high conversion efficiency are intensively pursued to date. Here, proposing by the d-d interband transitions, we report an unprecedented high-entropy alloy FeCoNiTiVCrCu nanoparticles that the energy regions below and above the Fermi level (±4 eV) have been fully filled by the 3d transition metals, which realizes an average absorbance greater than 96 % in the entire solar spectrum (wavelength of 250 to 2500 nm). Furthermore, we also calculated the photothermal conversion efficiency and the evaporation rate towards the steam generation. Due to its pronounced full light capture and ultrafast local heating, our high-entropy-alloy nanoparticle-based solar steam generator has over 98 % efficiency under one sun irradiation, meanwhile enabling a high evaporation rate of 2.26 kg m-2 h-1 .