Breaking Capacity Of Circuit Breaker Research Articles

The Influence of Novel Power System Characteristics on 330kV Power Grid Short-circuit Current

Under the development goal of “Carbon Peak, Carbon Neutralization”, the concept of novel power system is proposed. Its representative features include AC/DC interconnection of power grid and large-scale access of new energy power stations. Under these characteristics, higher requirements are put forward for the short-circuit current breaking capacity of the circuit breaker. The DC component of short-circuit current and the injection of new energy into the system short-circuit current cannot be ignored. Based on the 330kV local power grid in Northwest China, this paper studies the power grid operation mode, DC component of short-circuit current and the influence of photovoltaic power station on short-circuit current. The influence law of DC component of short-circuit current on the actual breaking capacity of circuit breaker and access of photovoltaic power station on the short-circuit current are summarized. It can provide a theoretical basis for the selection of circuit breaker in novel power system.

Study on the influence of speed in DRM of SF6 circuit breaker

As the breaking capacity of circuit breaker depends in part on the state of contact sets, and the states can be described by the electrical resistance. However, the electrical resistance shows great differences when the closing or opening speed changes due to the fault or degradation of operating mechanism, and the differences will cause trouble to the diagnosis results inevitably. In order to achieve accurate diagnosis of the contact condition, the mechanism of resistance changing with speeds has to be studied. In the present paper, the contact resistance under different speeds is measured by DRM experimental platform, and the characteristic parameters of resistance curves are extracted to show the positive correlation between contact resistance and speeds. What follows is a finite model of contact sets used to simulate the deformation and strain under different speeds. After the simulation, the influence mechanism is discussed, and a mathematical model is proposed.

An intelligent protection scheme to deal with extreme fault currents in smart power systems

In modern power systems, the generation capacity is increasing significantly for responding to high electric energy demands. This generation expansion directly affects the level of short circuit in transmission systems and increases the fault current magnitude, which may pass the breaking capacity of circuit breakers. To deal with extreme fault currents in power systems, an intelligent protection scheme is proposed in this paper, which removes the necessity of installing expensive fault current limiters. This protection scheme uses communication capabilities defined in IEC 61850 to design smart cascading switching actions to isolate the faulty part of the system. In fact, it is a supervisory protection algorithm in addition to the conventional distance protection, which is the main protection of HV transmission systems. This protection is activated if the fault current is higher than breaking capacity of circuit breakers; otherwise, the conventional distance protection is responsible to clear the fault. Numerical results obtained from implementing the proposed protection algorithm in a 400 kV system demonstrate the effectiveness of this method in terms of fault clearing time, stability margin improvement and power system economy.

고장 유형별 고속 인터럽터의 동작 특성

With the increasing power demands, size of the fault current in electrical grids is steadily increasing, and it exceeds the breaking capacity of circuit breakers. To effectively cope with these problems, a high-speed interrupter was suggested. The high-speed interrupter provides fault current with a bypass to a fault current limiter in case of accidents and consequently, fault current can be restricted. In this study, behavioral characteristics of high-speed interrupter were analyzed by accident types occurred in a distribution system. When accidents occurred, a and b contact of the high-speed interrupter were turned-off and then, turned-on. Accordingly, fault current flowed to the circuit connected to a current limiting element, and the fault current limiter restricted fault current to within a half-cycle. Nevertheless, the behavior of the high-speed interrupter was slowed down by a switching surge. As a result, fault current was confirmed to be restricted not to within the anticipated half-cycle, but to after a half-cycle. Moreover, the behavioral characteristics of the high-speed interrupter changed not only by accident types, but by behaviors of R, S, and T phases. This was due to the errors in stroke lengths of the high-speed interrupters, which resulted in a slight time discrepancy among three interrupters. In addition, the switching behaviors of the b and a contact were confirmed not to have coincided due to the switching surge; b contact behaved first and a contact followed. because of this, accuracy of stroke length and switching surges through the solenoid suction increases may be necessary to resolve.

Recovery behavior based on reclosing operation and a neutral line of three-phase flux-coupling type SFCL

The breaking capacity of circuit breakers currently reaches the saturation point in electric power systems when a fault occurs. This is because the fault current increases due to continuous increases in electric power demand and facilities. It is not efficient to change existing circuit breakers, however, because of some problems that will increase the replacement cost and cause technical difficulties. To solve such problems, a study on the superconducting fault current limiter (SFCL) is being actively conducted.In this paper, a three-phase flux-coupling-type SFCL was composed, and its recovery characteristic according to the change in the number of turns of its secondary coils and its reclosing operation were analyzed. The increase in the number of turns of the SFCL’s secondary coils enhances its limiting efficiency by increasing its total impedance. The recovery time was delayed, however, when the number of turns of the secondary coils increased, because the superconducting element was connected in parallel to the secondary coils, which increased the voltage and current of the superconducting element. In other words, the delay in the recovery time was due to the increase in the power burden between the superconducting elements. Thus, two superconducting elements that were connected in series were used to distribute the power burden to each other, and the recovery characteristics of the SFCL with and without a neutral line were experimented on.

재폐로 동작에 따른 초전도 한류기의 회복성능 분석

The breaking capacity of circuit breakers could be no more increased in the electric power system. This is because the fault current increases due to continuous increases in electric power demand and facilities. To solve the problem, it is necessary to come up with an alternative. The superconducting fault current limiter (SFCL) has received an attention among various alternatives. The SFCL effectively reduce a fault current in cooperation with a power circuit breaker. A various types of the SFCL are suggested and a study on them have been progressed. As a result of it, the SFCL can be applyed to the electric power system in the near future. But, a study on recovery behaviors of the SFCL is not enough for applying to the electric power system. If the superconducting elements do not completely recover to the superconducting state after fault operation, it might be a breakdown of the superconducting elements due to heavy power burden and it gives an bad influence on the working of other electric devices. Additionally, the distribution power system has reclosing operation such as open-0.3sec-closed/open-3min-closed/open procedure. So we need to study more about improvement of the recovery behaviors of the SFCL. In this paper, we analyzed the recovery behaviors of a flux-coupling type SFCL according to reclosing operation when a single line-to-ground fault occurred and we compared recovery behaviors of the SFCL with and without a neutral line between secondary reactors and superconducting elements. Also, the flux-coupling type SFCL has advantageous for increases of capacity by controlling the variation in turn ratios between two reactors. Consequently, when the number of turns of the secondary reactors increased, the power burden of the superconducting elements was bigger due to the increase of impedances of the secondary reactors. To distribute the power burden, two superconducting elements connected in series and the balanced quenching of the superconducting elements was induced by connecting a neutral line.