Boron Nitride Research Articles

On the analysis of physical properties of thermal interfaces based on hexagonal boron nitride and copper

The physical properties (thermal and thermal diffusivity) of thermal interfaces based on powdered boron nitride with a hexagonal crystal lattice (h-BN) and copper with a cubic crystal lattice (Cu) for cooling the electronic component base of micro- and nanoelectronics are studied. The physical properties are determined by the flash method. The prospects of using pressed hexagonal boron nitride powder as a thermal interface without using a binder are described. A comparison with the physical properties of other thermal interfaces that are widely used at present is made.

Sonochemical amino-functionalization of hexagonal boron nitride nanosheets produced by liquid phase exfoliation

The functionalization of hexagonal boron nitride nanosheets (hBNNSs) is a powerful strategy to improve their properties, such as dispersibility and stability in aqueous media, biocompatibility, and surface affinity. In this work, we report the functionalization of hBNNSs using a two-step strategy. First, hBN powder was exfoliated at ambient temperature by liquid phase exfoliation method into deionized water/isopropanol mixture and the resultant hBNNSs were characterized by transmission electron microscopy, X-ray diffraction and Raman spectroscopy. In the second step, the surface of the hBNNSs was modified with amino groups by means an ultrasonic wave-assisted functionalization process using hydrazine hydrate as functionalization agent. The amino-functionalization of the hBNNSs was confirmed by Infrared (IR) spectroscopy and thermogravimetric analysis (TGA). Our results showed that in an exfoliation optimized process with a sonication time of 4 h, the yield of hBNNSs reach 66 %, and that the hBNNSs can be dispersed in water, isopropanol, and water/isopropanol 75:25 at concentrations of up to 1.5 mg/mL. IR analysis confirmed that the amino groups were successfully grafted on hBNNSs, whereas TGA curves revealed that the content of –NH2 groups in the NH2-hBNNSs vary from 0.9 to 3.2 wt% depending of functionalization agent amount. Due to the polar nature of the amino groups, the NH2-hBNNSs exhibit higher stability and dispersibility in aqueous media compared with the unmodified hBNNSs. Particularly, the NH2-hBNNSs can be dispersed in water/isopropanol 75:25 at concentration from 7 to 15 mg/mL, depending on the content of amino groups.

Influence of boron nitride reinforcement particles on physical and tribological properties of Al7079 MMCs

Influence of boron nitride reinforcement particles on physical and tribological properties of Al7079 MMCs

Generation of stable dual-wavelength mode-locked pulses using boron nitride saturable absorber in all-polarization-maintaining Er-doped fiber laser

This work demonstrates the generation of stable dual-wavelength mode-locked pulses using boron nitride (BN) as a novel saturable absorber within a polarization-maintaining (PM) Er-doped fiber laser cavity. BN was chosen due to its exceptional properties, including high thermal stability, wide bandgap, and excellent mechanical strength. A drop-casting technique was employed to fabricate the BN-based saturable absorber. The laser generated high-quality dual-wavelength pulses centered at 1566.3 nm and 1575.6 nm with a repetition frequency of 25.3 MHz and a pulse width of 900 ps. The generated laser exhibited excellent stability and a high degree of polarization (DOP) of 99.8 %. These findings contribute to the advancement of dual-wavelength mode-locked fiber laser technology and open new avenues for applications such as dual-frequency comb spectroscopy.

High-speed turning of AISI 4340 alloy steel using carbide tools in a sustainable minimum quantity lubrication environment

Purpose This study aims to investigate the machining performance of CVD-coated carbide tools by considering most crucial machinability aspects: cutting force, tool life, surface roughness and chip morphology in high-speed hard turning of AISI 4340 alloy steel under a sustainable minimum quantity lubrication (MQL) environment. Design/methodology/approach The purpose of this study is to analyze the performance of coated carbide tools under MQL environment therefore, machining tests were performed in accordance with the Taguchi L9 orthogonal array, accommodating the three crucial machining parameters such as cutting speed (V = 300–400 m/min), feed rate (F = 0.1–0.2 mm/rev) and depth of cut (DOC = 0.2–0.4 mm). The measured or calculated values obtained in each experimental run were validated for normality assumptions before drawing any statistical inferences. Taguchi signal-to-noise (S/N) ratio and analysis of variance methodologies were used to examine the effect of machining variables on the performance outcomes. Findings The quantitative analysis revealed that the depth of cut exerted the most significant influence on cutting force, with a contributing rate of 60.72%. Cutting speed was identified as the primary variable affecting the tool life, exhibiting a 47.58% contribution, while feed rate had the most dominating impact on surface roughness, with an overall contributing rate of 89.95%. The lowest cutting force (184.55 N) and the longest tool life (7.10 min) were achieved with low machining parameters at V = 300 m/min, F = 0.1 mm/rev, DOC = 0.2 mm. Conversely, the lowest surface roughness (496 nm) was achieved with high cutting speed, low feed rate and moderate depth of cut at V = 400 m/min, F = 0.1 mm/rev and DOC = 0.3 mm. Moreover, the microscopic examination of the chips revealed a serrated shape formation under all machining conditions. However, the degree of serration increased with an incremental raise with cutting speed and feed rate. Research limitations/implications The study is limited to study the effect of machining parameters within the stated range of cutting speed, feed rate and depth of cut as well as other parameters. Practical implications Practitioners may consider to adopt this machining technique to create more sustainable working environment as well as eliminate the disposal cost of the used metal cutting fluid. Social implications By applying this machining technique, diseases caused by metal cutting fluid to the mechanist will be significantly reduced, therefore creating better lifestyles. Originality/value Hard turning is commonly carried out with advanced cutting tools such as ceramics, cubic boron nitride and polycrystalline cubic boron nitride to attain exceptional surface finish. However, the high cost of these tools necessitates exploration of alternative approaches. Therefore, this study investigates the potential of using cost-effective, multilayer-coated carbide tools under MQL conditions to achieve comparable surface quality. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2024-0013/

Optical control of multiple resistance levels in graphene for memristic applications

Neuromorphic computing has emphasized the need for memristors with non-volatile, multiple conductance levels. This paper demonstrates the potential of hexagonal boron nitride (hBN)/graphene heterostructures to act as memristors with multiple resistance states that can be optically tuned using visible light. The number of resistance levels in graphene can be controlled by modulating doping levels, achieved by varying the electric field strength or adjusting the duration of optical illumination. Our measurements show that this photodoping of graphene results from the optical excitation of charge carriers from the nitrogen-vacancy levels of hBN to its conduction band, with these carriers then being transferred to graphene by the gate-induced electric field. We develop a qualitative model to describe our observations. Additionally, utilizing our device architecture, we propose a memristive crossbar array for vector-matrix multiplications.

Investigating the Exfoliated Hexagonal Boron Nitride Nanosheets Embedded on Bi2S3 Nanorods Designed as a Positive Electrode for Hybrid Supercapacitors

Investigating the Exfoliated Hexagonal Boron Nitride Nanosheets Embedded on Bi₂S₃ Nanorods Designed as a Positive Electrode for Hybrid Supercapacitors

Boron nitride: Novel ceramic reductant for low‐activity waste vitrification

AbstractDuring vitrification of radioactive wastes, excessive foaming reduces processing rates within melters by hindering heat transfer from the molten glass pool to the reacting melter feed. Formulations of low‐activity waste (LAW) melter feeds, for vitrification at the Waste Treatment and Immobilization Plant at the Hanford Site, conventionally include the addition of sucrose to mitigate excessive foaming by hastening the denitration process. However, incomplete combustion of sucrose produces organics such as acetonitrile (C2H3N) that may exceed bounding limits of downstream effluent treatment facilities. Using boron nitride (BN) as an alternate reductant to sucrose, in a representative LAW melter feed reduced C2H3N production by 90% by preventing the low‐temperature sucrose–nitrate reactions. Furthermore, foaming was suppressed due to the higher decomposition temperature of BN than H3BO3 meaning a delayed reaction of a large fraction of boron with the transient glass‐forming melt until above the foam onset temperature, thus reducing the quantity and viscosity of the connected melt and trapping less gas in the foam layer.

Polyol Synthesis of Bimetallic FePt Nanoparticles over h-BN Substrate

Hexagonal boron nitride (h-BN) is a promising support for the deposition of functional metallic nanoparticles for next generation of catalysts. Multicomponent metallic NPs, such as bimetallic FePt NPs, are attracting much attention as catalytically active sites because their properties can be superior to their single-element counterpart. To achieve the best catalytic properties, careful control of the chemical composition of the bimetallic NPs on the surface of h-BN substrates is necessary. Herein we report the development of a polyol synthesis protocol that elucidates the relationship between the initial and resulting Fe:Pt molar ratio in a FePt/h-BN material. TEM, STEM, EDXS, BET and BJH methods were utilized to characterize the surface and structure of the h-BN support and FePt/h-BN heterostructures.

Investigating the Effects of Boron Nitride on Mechanical Properties of CoCrFeNiMn Composites

High‐entropy alloys (HEAs) are gaining attention for their exceptional properties but achieving precision and surface quality in powder metallurgy (PM) can be challenging. This study investigates the mechanical properties of CoCrFeNiMn HEAs produced through the flake powder metallurgy (FPM) technique and laser powder bed fusion (LPBF) preservative industrial, which established outstanding antiwear properties. To assess the enhancement of mechanical behavior and wear resistance by incorporating boron nitride (BN) into CoCrFeNiMn composites is fabricated via FPM. By incorporating BN into the composites, the mechanical behavior is significantly enhanced, leading to improved resistance against wear. Furthermore, the study delivers comprehensions into the serration behavior microstructure and shear localization in a high‐strain‐rate‐deformed CoCrFeMnNi entropy‐high alloy produces through metallurgy in powder. The serration behavior of the CoCrFeMnNi HEA is discussed concerning strain rate and temperature. Accordingly, the study employs the LPBF technique to fabricate the CoCrFeMnNi alloy from the prepared flakes. Microstructural characterization using scanning electron microscopy and X‐ray diffraction techniques to explore phase distribution, grain size, and possible segregation in the CoCrFeMnNi alloy produced through FPM‐LPBF is performed. In this particular investigation, a gradient microstructure is achieved through fusion in a laser‐powder bed of CoCrFeMnNi HEA onto highly deformed equal‐atomic HEA sheets. The resulting combination of partially recrystallized regions, exhibiting elevated yield strength, and fully recrystallized regions, demonstrates enhanced strain hardenability and elongation, and yields superior mechanical properties. The results obtained from the FPM‐LPBF CoCrFeMnNi alloy will be compared with those of conventionally processed CoCrFeMnNi to highlight the advantages and improvements achieved through the proposed method. The study findings reveal that the fundamental understanding of HEAs’ behavior under LPBF with FPM affords valuable insights into optimizing the processing parameters and achieving superior mechanical attributes.

Probing structural and electrochemical properties of a 2D CoMoO4@hBN nanocomposite as pseudocapacitive electrode for high-performance supercapacitors

The effectiveness of energy storage is largely determined by the electrode material's performance in critical areas. Enhancements in ion transport, cyclic stability, rate capability, and specific capacitance directly boost the supercapacitors' overall performance and broaden their application potential. This study aims to enhance these properties by incorporating hexagonal boron nitride (hBN) into cobalt molybdate (CoMoO4) material in a 1:1 stoichiometric ratio. The CoMoO₄@hBN nanocomposite was synthesized using a hydrothermal method followed by ball milling. The X-ray diffraction (XRD) analysis confirmed the formation of a single-phase CoMoO4@hBN composite, with a significant increase in crystallite size from 18.21 nm in pure CoMoO₄ to 25.6 nm, along with a slight shift in diffraction peaks, indicating enhanced crystallinity and structural defects due to the substitution of oxygen with boron atoms. Raman spectroscopy revealed that the composite retains the characteristic peaks of both CoMoO₄ and hBN, with stable sharp peaks at 936 cm−1 (Mo=O bond) and 1367 cm−1 (E2g peak of hBN) even after 20 depth measurements, confirming successful conjugation and consistent vibrational properties. The X-ray photoelectron spectroscopy (XPS) showed a slight shift in Co 2p and Mo 3d binding energies to higher values, suggesting improved electronic interactions between CoMoO4 and hBN, which could enhance the composite's conductivity. The electrochemical analysis demonstrated that incorporating h-BN significantly boosts the electrode's performance compared to pristine CoMoO4, with about 37 % increase in specific capacitance at 1 A g−1, reduced charge transfer resistance (0.11 Ω), and superior cyclic stability with 96 % capacitance retention after 5000 cycles. These findings indicate that hBN enhances both the electrical conductivity and structural integrity of CoMoO4, positioning the CoMoO4@hBN composite as a promising material for high-performance supercapacitors.

Impact of valley degeneracy on the thermoelectric properties of zig-zag graphene nanoribbons with staggered sublattice potentials and transverse electric fields.

This study investigates the band inversion of flat bands in zig-zag graphene nanoribbons (ZGNRs) using a tight-binding model. The band inversion results from symmetry breaking in the transverse direction, achievable through deposition on specific substrates such as separated silicon carbide or hexagonal boron nitride sheets. Upon band inversion, ZGNRs exhibit electronic structures characterized by valley degeneracy and band gap properties, which can be modulated by transverse electric fields. To explore the impact of this level degeneracy on thermoelectric properties, we employ Green's function techniques to calculate thermoelectric quantities in ZGNR segments with staggered sublattice potentials and transverse electric fields. Two carrier transport scenarios are considered: the chemical potential is positioned above and below the highest occupied molecular orbital. We analyze thermionic-assisted transport (TAT) and direct ballistic transport (DBT). Level degeneracy enhances the electric power factors of ZGNRs by increasing electrical conductance, while the Seebeck coefficient remains robust in the TAT scenario. Conversely, in DBT, the enhancement of the power factor primarily stems from improvements in the Seebeck coefficient at elevated temperatures.

Robust Plasma-Assisted Growth of 2D Janus Transition Metal Dichalcogenides and Their Enhanced Photoluminescent Properties.

Janus transition metal dichalcogenides (TMDs) are a novel class of 2D materials with unique mirror asymmetry. Plasma-assisted synthesis at room temperature is favored for producing Janus TMDs due to its energy efficiency and prevention of alloying. However, current methods require stringent control over growth conditions, risking defects or unintended materials. A robust plasma-assisted (RPA) synthesis strategy is introduced, incorporating a built-in tube with a suitable inner diameter into the plasma-assisted system. This innovation creates a mild, uniform plasma atmosphere, allowing for broader variations in growth parameters without significantly affecting Janus MoSSe's morphology and characteristics. This approach simplifies the synthesis process and enhances the success rate of Janus TMD production. Additionally, methods are explored to enhance the photoluminescence (PL) of Janus MoSSe. Releasing MoSSe from the growth substrate and annealing it removes strain and unintentional doping, improving PL performance. MoSSe on hexagonal boron nitride (h-BN) flakes after annealing shows a 32-fold increase in PL intensity. Bis(trifluoromethane) sulfonimide (TFSI) treatment of MoSSe results in a remarkable 70-fold increase in PL intensity, a 2.5-fold extension in exciton lifetime, and quantum yield (QY) reaching up to ≈31.2%. These findings provide critical insights for optimizing the luminescence properties of 2D Janus materials, advancing Janus optoelectronics.

Mapping the energy-momentum dispersion of hBN excitons and hybrid plasmons in hBN-WSe2 heterostructures

Heterostructures obtained by combining two-dimensional (2D) sheets are widely investigated as a platform for designing new materials with customised characteristics. Transition metal dichalcogenides (TMDCs) are often combined with hexagonal boron nitride (hBN) to enhance their excitonic resonances. However, little is known about how stacking affects excitons and plasmons in TMDCs or their mutual interactions. Here, we combine momentum-resolved electron energy-loss spectroscopy with first-principles calculations to study the energy-momentum dispersion of plasmons in multi-layer WSe2-hBN heterostructures as well as in their isolated components. The dispersion of the high-momentum excitons of hBN, alone and in combination with WSe2, is mapped across the entire Brillouin zone. Signatures of hybridisation in the plasmon resonances and some of the excitons suggest that the contribution of hBN cannot be neglected when interpreting the response of such a heterostructure. The consequences of using hBN as an encapsulant for TMDCs are also discussed.

Charge-Selective 2D Heterointerface-Driven Multifunctional Floating Gate Memory for In Situ Sensing-Memory-Computing.

Flash memory, dominating data storage due to its substantial storage density and cost efficiency, faces limitations such as slow response, high operating voltages, absence of optoelectronic response, etc., hindering the development of sensing-memory-computing capability. Here, we present an ultrathin platinum disulfide (PtS2)/hexagonal boron nitride (hBN)/multilayer graphene (MLG) van der Waals heterojunction with atomically sharp interfaces, achieving selective charge tunneling behavior and demonstrating ultrafast operations, a high on/off ratio (108), extremely low operating voltage, robust endurance (105 cycles), and retention exceeding 10 years. Additionally, we achieve highly linear synaptic potentiation and depression, and observe the reversibly gate-tunable transitions between positive and negative photoconductivity. Furthermore, we employed the VGG11 neural network for in situ trained in-sensor-memory-computing to classify the CIFAR-10 data set, pushing accuracy levels comparable to pure digital systems. This work could pave the way for seamlessly integrated sensing, memory, and computing capabilities for diverse edge computing.

Transferable Percolated Particle Monolayers Derived from Marangoni Flows for Thermally Conductive Dielectric Coatings.

Thermal management is becoming one of the most significant design and size limitations for high power density electronics, including motherboards, power converters, and phased array antennas for 5G communications. There are few options for conducting heat away with dielectric materials that avoid shortening or distorting the performance of these electronics. Certain highly thermally conductive 2D and 3D materials, including hexagonal boron nitride and diamond, offer ideal material properties to address these issues but are extremely challenging to process. This work studies highly oriented single-particle thick films of hexagonal boron nitride, manufactured through a modified Langmuir-Blodgett process and densified further using the Marangoni effect to attain remarkable thermal conductivity enhancement with minimal coating thickness. High loadings of hexagonal boron nitride (∼60 vol %) in dense, castable films are also produced to compare thermal spreading ability in a comparatively simpler but less-coordinated percolated system to the highly percolated particle monolayers. These procedures were applied to glass fiber reinforced polymers used in aerospace and radome applications as well as to a single-board computer to demonstrate enhanced thermal management.

Stereolithography Printing and Mechanical Properties of Polyethylene Glycol Diacrylate/Hexagonal Boron Nitride Ceramic Composites

To enhance the mechanical properties of bioceramic composite bone scaffolds, a composite paste of polyethylene glycol diacrylate (PEGDA) and hexagonal boron nitride (h‐BN) with a solid content of up to 42 wt% was developed in this study. The part was produced using stereolithography (SLA). The SLA printing parameters and material ratios of the paste were optimized through a homogeneous design and mechanical property tests. The results indicate that the single‐line curing width of the PEGDA/h‐BN paste in the XY plane ranged from 172 to 209 μm, while the curing depth of a single layer along the Z‐axis ranged from 99 to 154 μm. Laser power was identified as the primary factor influencing both the width and depth of curing. The compressive strength of the printed sample of PEGDA/h‐BN ceramic composite paste was measured at 222.4 ± 5.6 MPa, which is 61 times greater than the compressive strength of a pure PEGDA structure and comparable to that of cortical bone (100‐230 MPa). Finally, the superior biocompatibility of PEGDA/h‐BN ceramics was confirmed through cytotoxicity experiments. Consequently, PEGDA/h‐BN ceramic composites meet the mechanical properties and biocompatibility requirements necessary for bone tissue applications, indicating promising potential in the field of bone tissue engineering.

Metal Replacement in Aeronautics Applications Using Two‐Dimensional Multifunctional Composites

Carbon‐based composites have replaced metals in many structural components of modern airplanes; however, functional applications still require metal conductors and devices. Here, the production and integration in small‐scale airplane parts of electric devices based on metal‐free layered composites of graphene, boron nitride, and polymers are described. Thanks to their two‐dimensional structure, these materials feature excellent tunable thermoelectrical properties and high flexibility. We describe the production and performance of heaters and ice sensors installed on scaled NACA‐0012 airfoils to avoid ice formation, to remove ice or to detect the ice on the outer skin of the airfoil. We demonstrate that we can tune the electrical conductivity of the composite heating element from 105 to 103 S m−1 that is preserved even after 1000 bending cycles. The heaters successfully achieve anti‐icing and deicing in representative icing conditions and can sustain high‐power densities as required for electrothermal ice‐protection systems in aviation. The composite material can be readapted into a sensor able to detect ice formation in real time in an icing wind tunnel. Moreover, the possibility to use the heaters developed as heating molds to cure composite materials by out‐of‐oven curing, with a significant energy saving potential, is demonstrated.

Exploring the mechanical and thermal properties of rubber-based nanocomposite: A comprehensive review

Abstract The emergence and progression of synthetic rubber have paved the way in variegated prospects across various engineering and technological fields. Nonetheless, its inherent limitations such as poor mechanical and thermal properties including wear resistance, poor tensile strength, and lower thermal conductivity, as evident in styrene butadiene rubber and silicone rubber, have constrained its utility in numerous load-bearing scenarios. This limitation has been addressed by incorporating specific nanofillers into various rubber compositions, resulting in promising outcomes up to a certain threshold. Many nanofillers were trialed, such as graphite oxide, aluminum oxide, carbon nanotubes, and boron nitride. However, an attempt should be made to explore the disparity in dimensional attributes of nanofillers and their effect on different properties of rubber, thereby delineating the scope for future research. The exploration of dimensionally distinct nanofillers, such as 1D multiwalled carbon nanotubes and 2D graphene, can overcome these limitations and augment rubber’s mechanical properties and thermal properties. The study also delineates the scope of future research, which should be focused on optimizing the nanofillers’ dispersion and interfacial bonding within the rubber matrix by trying dimensionally different nanofillers.

Cobalt-doped iron-based Prussian blue analogue cubes anchored to phosphorus‑nitrogen-covered BN surfaces for enhancing the flame retardancy of epoxy coatings

Prussian blue analogue (PBA) is considered to be a very promising inorganic nano-flame retardant material due to its structure enriched with transition metal elements. Here, hexachlorocyclotriphosphazene (HCCP) and p-phenylenediamine (p-PDA) were first loaded onto the boron nitride surface (BN/PCP) via a polymerization reaction to impart richer flame retardant characteristics. Then, Co-Fe-based PBA nanoparticles were homogeneously anchored on the BN/PCP surface to obtain the BN/PCP@PBA hierarchical nano-flame retardant. It is worth mentioning that this novel composite flame retardant effectively combined the superior barrier properties of BN, fire retardancy of N, P elements and the accelerated carbon conversion effect of Co-Fe/PBA. The test results showed that the loading of PCP on the BN surface could effectively improve the thermal insulation performance of EP, while Co-Fe/PBA had good catalytic carbon formation effect at high temperature. Specifically, the backside of the BN/PCP@PBA filled EP sample displayed the lowest temperature during flame attack (164.1 °C) compared to the other specimens, proving its best thermal insulation. The BN/PCP@PBA/EP obtained the maximum expansion height and expansion rate values (27.6 mm and 21.07) in the furnace chamber experiments, which are crucial for its fire resistance. In addition, BN/PCP@PBA/EP retained the highest residual char (32.6 %) and achieved the lowest smoke density rating (36.9 %), demonstrating its high carbon conversion and fume suppression. Carbon residue analysis confirmed that the char layer of BN/PCP@PBA/EP was more complete and the metal oxides were uniformly embedded in the carbon residue skeleton, which ensured good flame protection for the substrate.