Bone-implant Contact Ratio Research Articles

Biocompatibility and dimensional stability through the use of 3D-printed scaffolds made by polycaprolactone and bioglass-7: An in vitro and in vivo study.

This experiment aimed to observe the differences in biological properties by producing BGS-7 + PCL scaffolds with different weight fractions of BGS-7 through 3D printing and to confirm whether using the scaffold for vertical bone augmentation is effective. Cube-shaped bioglass (BGS-7) and polycaprolactone (PCL) scaffolds with different weight fractions (PCL alone, PCL with 15% and 30% BGS-7) are produced using 3D printing. The surface hydroxyapatite (HA) apposition, the pH change, proliferation and attachment assays, and various gene expression levels are assessed. After a 7-mm implant was inserted 3 mm into the rabbit calvaria, vertical bone augmentation is performed around the implant and inside the scaffold in four ways: scaffold only, scaffold+bone graft, bone graft only, and no graft. Sacrifice is performed at 6, 12, and 24 weeks, and the various parameters are compared radiographically and histologically. HA apposition, cell proliferation, cell attachment, and expression of osteogenic genes increase as the proportion of BGS-7 increase. In the in vivo test, a higher bone-implant contact ratio, bone volume ratio, bone mineral density, and new bone area are observed when the scaffold and bone grafts were used together. The 3D-printed scaffold, a mixture of BGS-7 and PCL, exhibit higher biological compatibility as the proportion of BGS-7 increase. Additionally, the use of scaffold is effective for vertical bone augmentation.

Evaluate the effects of low-intensity pulsed ultrasound on dental implant osseointegration under type II diabetes.

Objective: The objective of this study is to assess the impact of low-intensity pulsed ultrasound (LIPUS) therapy on the peri-implant osteogenesis in a Type II diabetes mellitus (T2DM) rat model. Methods: A total of twenty male Sprague-Dawley (SD) rats were randomly allocated into four groups: Control group, T2DM group, Control-LIPUS group, and T2DM-LIPUS group. Implants were placed at the rats' bilateral maxillary first molar sites. The LIPUS treatment was carried out on the rats in Control-LIPUS group and T2DM-LIPUS group, immediately after the placement of the implants, over three consecutive weeks. Three weeks after implantation, the rats' maxillae were extracted for micro-CT, removal torque value (RTV), and histologic analysis. Results: Micro-CT analysis showed that T2DM rats experienced more bone loss around implant cervical margins compared with the non-T2DM rats, while the LIPUS treated T2DM rats showed similar bone heights to the non-T2DM rats. Bone-implant contact ratio (BIC) were lower in T2DM rats but significantly improved in the LIPUS treated T2DM rats. Bone formation parameters including bone volume fraction (BV/TV), trabecular thickness (Tb.Th), bone mineral density (BMD) and RTV were all positively influenced by LIPUS treatment. Histological staining further confirmed LIPUS's positive effects on peri-implant new bone formation in T2DM rats. Conclusion: As an effective and safe treatment in promoting osteogenesis, LIPUS has a great potential for T2DM patients to attain improved peri-implant osteogenesis. To confirm its clinical efficacy and to explore the underlying mechanism, further prospective cohort studies or randomized controlled trials are needed in the future.

The Effects of Corona Stimulation on the Osseointegration of Dental Implants: An Experimental Study

Aim: Currently, one of the most promising research areas in dental implantology is the exploration of additional procedures to reduce loading time for implants and enhance osseointegration in cases of poor bone quality. Various techniques have been researched and developed for stimulating bone production, including electrical stimulation of the jawbone and surrounding tissues. However, there is limited research on the direct relationship between electrostimulation and osseointegration. This experimental study aims to investigate the effects of corona stimulation (CS) on the rate and quality of osseointegration, as well as its potential to reduce the waiting period for dental implants. Material and Method: In this experimental protocol, 32 dental implants were inserted into the tibia of four male sheep bilaterally. Implants on the right tibia of each male sheep underwent CS treatment, while the other side served as a control group without any stimulation. The animals were sacrificed on the 15th and 30th days after implantation. Bone segments containing the implants were processed using a noncalcified method. It assessed new bone formation and osseointegration around the dental implants using the undecalcified method and histomorphological analysis. An experienced blinded investigator measured percentages of mineralized bone-implant contact (BIC), bone area (BAr), and bone perimeter (BPm) to evaluate the bone-implant interface. Statistical analyses were performed using SPSS 21 for Windows, with a significance level set at p<0.05. Results: The histomorphometric parameters revealed a significant increase in BIC, BAr, and BPm values in the CS group compared to the control group on both the 15th and 30th days (p<0.05). There was no statistically significant difference in BIC ratio between the second and fourth stimulation groups. Conclusion: The findings of this experimental study suggest that CS may have a positive impact on the early osseointegration period of dental implants.

Study on Osseointegration Capability of β-Type Ti-Nb-Zr-Ta-Si Alloy for Orthopedic Implants.

Osseointegration is the basic condition for orthopedic implants to maintain long-term stability. In order to achieve osseointegration, a low elastic modulus is the most important performance indicator. It is difficult for traditional titanium alloys to meet this requirement. A novel β-titanium alloy (Ti-35Nb-7Zr-5Ta)98Si2 was designed, which had excellent strength (a yield strength of 1296 MPa and a breaking strength 3263 MPa), an extremely low elastic modulus (37 GPa), and did not contain toxic elements. In previous in vitro studies, we confirmed the good biocompatibility of this alloy and similar bioactivity to Ti-6Al-4V, but no in vivo study was performed. In this study, Ti-6Al-4V and (Ti-35Nb-7Zr-5Ta)98Si2 were implanted into rabbit femurs. Imaging evaluation and histological morphology were performed, and the bonding strength and bone contact ratio of the two alloys were measured and compared. The results showed that both alloys remained in their original positions 3 months after implantation, and neither imaging nor histological observations found inflammatory reactions in the surrounding bone. The bone-implant contact ratio and bonding strength of (Ti-35Nb-7Zr-5Ta)98Si2 were significantly higher than those of Ti-6Al-4V. The results confirmed that (Ti-35Nb-7Zr-5Ta)98Si2 has a better osseointegration ability than Ti-6Al-4V and is a promising material for orthopedic implants.

Comparative analysis of anchorage strength and histomorphometric changes after implantation of miniscrews in adults and adolescents: an experimental study in Beagles

ObjectivesThis study aimed to explore the differences in anchorage strength and histomorphometric changes in orthodontic miniscrews between adult and adolescent beagles.Material and methodSix adult beagles and six young beagles were used as experimental subjects, and eight miniscrews were symmetrically placed in the posterior mandible of each dog. Measurement of the displacement (mm) of two adjacent miniscrews after load application was performed to compare the anchorage strength between the adult and adolescent groups. Three intravital bone fluorochromes (oxytetracycline, calcein green, xylenol orange) were administered postoperatively to mark the active bone-forming surface. Subsequently, the mineral apposition rate and bone-implant contact ratio were measured for dynamic and static histomorphometry. Finally, the expression levels of the RANKL/OPG ratio were evaluated by immunohistochemistry.ResultsThe average displacement of miniscrews in the adult group was significantly less than that in the adolescent group after load application. For histomorphometry analysis, the mineral exposure rate in the adolescent group was higher than that in the adult group with or without force application. In addition, more fractures and new bone formation but deceased bone-implant contact ratios were observed in the adolescent group than in the adult group. The ratio of RANKL/OPG expression increased more in the adolescent group than in the adult group.ConclusionMiniscrews do not remain in the same position as skeletal anchors, and the amount of displacement was higher in adolescent group than that in adult group, reflecting the weaker anchorage strength of miniscrews in adolescents due to the higher bone turnover rate and active bone remodelling. Therefore, it is feasible to apply orthodontic loading to the miniscrews in adult patients earlier, even immediately, but it is recommended to wait a period for the adolescents.

Improvement implant osseointegration through nonthermal Ar/O2 plasma.

This study investigated the effects of nonthermal Ar/O2 plasma on the osseointegration of titanium implants. Through 8 weeks' in vivo evaluation of implants inserted into femoral bones of male Sprague-Dawley rats, the new bone mineralization apposition rate (MAR) is increased by 1.87 and 2.14 times for implants of smooth machined (SM) and sand-blasted and acid-etched (SLA) after plasma treatment. The bone volume fraction (bone volume/total volume, BV/TV) and bone-implant contact (BIC) ratios are improved by 1.31, 1.26 times and 1.35, 1.15 times after 90 s plasma treatment. The improved hydrophilicity rather than implant surface morphology is believed to play a critical role for the osseointegration improvement.

Bone marrow stromal cell-derived exosome combinate with fibrin on tantalum coating titanium implant accelerates osseointegration.

This study aims to present a sustainably releasing system of exosomes-fibrin combinate loaded on tantalum-coating titanium implants. We hope to investigate potential effects of the system on osseointegration between tantalum coating titanium implants and its surrounding bone tissue. Exosomes derived from rabbit bone marrow stromal cells (rBMSCs) and fibrin were deposited onto the micro-nanostructure tantalum coating surface (Ta + exo + FI) and compared to control groups, including tantalum coating (Ta), tantalum coating loaded exosomes (Ta + exo) and tantalum coating loaded fibrin (Ta + FI). The optimal concentration of loading exosomes, exosomes uptake capacity by BMSCs, and the effect of controlled-release by fibrin were assessed by laser scanning confocal microscope (LCSM) and microplate reader. The optimal concentration of exosomes was 1μg/μL. Adhesion, proliferation, and osteogenic differentiation ability of BMSCs on different materials were assessed in vitro. Finally, osseointegrative capacity of Ta, Ta + exo, Ta + FI, Ta + exo + FI implants in rabbit tibia were respectively evaluated with histology and bone-implant contact ratio (BIC%). It was demonstrated that exosome sustained-release system with fibrin loading on the tantalum coating was successfully established. Fibrin contribute to exosomes release extension from 2d to 6d. Furthermore, Ta + exo + FI significantly promoted adhesion, proliferation, and osteogenic differentiation of BMSCs. In vivo, the implants in Ta + exo + FI group displayed the highest osseointegrative capability than those in other groups. It is concluded that this exosome delivery system on the implants may be an effective way for tantalum coating titanium implants to promote osseointegration between implant and its surrounding bone tissue.

Osteogenic effect of low-intensity pulsed ultrasound on peri-implant bone: A systematic review and meta-analysis.

Purpose This study aimed to evaluate the effect of low-intensity pulsed ultrasound (LIPUS) on promoting osseointegration around dental implants.Study selection A comprehensive search was performed on two databases, including MEDLINE (PubMed) and Web of Science to identify relevant studies published before June 1, 2022. Randomized controlled trials that met the inclusion criteria were selected for the study. The year of publication, study design, animal species, number of animals, number of implants, implant position, implant size, intervention, follow-up time, bone volume ratio (BV/TV), bone-implant contact ratio (BIC), and implant removal torque value (RTV) measurements, including mean and SD, were extracted.Results Ten randomized trials were included in this meta-analysis. The results showed that LIPUS significantly promoted osteogenesis around dental implants. Furthermore, in animal models of pre-existing diseases such as osteoporosis and diabetes, LIPUS had the same effect. The included data were divided into subgroups to explore the effects of different follow-up time, acoustic intensities, and frequencies. Results showed that higher acoustic intensities and frequencies significantly improve the osteogenic effects of LIPUS. There was some degree of heterogeneity owing to bias in the included studies. More high-quality randomized controlled trials are necessary in the future.Conclusions LIPUS can promote bone healing around dental implants and is an attractive option for edentulous patients, especially those with pre-existing diseases. Further clinical trials on the use of LIPUS in implant dentistry are warranted. Furthermore, future studies must pay more attention to acoustic intensity and frequency.

The effects of collagen cross-link deficiency on osseointegration process of pure titanium implants.

This study aimed to investigate the effect of collagen cross-link deficiency on collagen fiber formation around an implant and its effect on the osseointegration process. Wistar rats were fed 0.1% beta-aminopropionitrile (BAPN) dissolved in water to induce collagen cross-link deficiency. Custom-made mini-implants with machined surfaces were placed proximal to the tibia. At 1, 2, and 4 weeks postoperatively, the bone area around the implant, bone-implant contact ratio, osteoclast/osteocyte activity, and osseointegration strength were evaluated using histological and immunohistochemical analyses and biomechanical tests. Long-term disturbance of collagen cross-link formation in the BAPN group resulted in faster collagen fiber maturation than that in controls, with a defective collagen structure, low bone formation quantity, and low bone-implant contact values. Deficiency of collagen cross-links resulted in increased bone resorption and decreased osteocyte activity. Collagen cross-linking is important for the formation of the collagen matrix, and their deficiency may impair bone activity around implants, affecting the osseointegration process.

Sinus augmentation with poly(ε)caprolactone-β tricalcium phosphate scaffolds, mesenchymal stem cells and platelet rich plasma for one-stage dental implantation in minipigs.

This study evaluated the efficacy of a tube-shaped poly(ε) caprolactone - β tricalcium phosphate (PCL-TCP) scaffold with the incorporation of human umbilical cord-derived mesenchymal stem cells (hUCMSCs) and platelet-rich plasma (PRP) for bone regeneration in the procedure of single-stage sinus augmentation and dental implantation in minipigs. Implants were placed in the bilateral sides of the maxillary sinuses of 5 minipigs and allocated to a PCL-TCP+hUCMSCs+PRP group (n=5), a PCL-TCP+PRP group (n=5), and a PCL-TCP-only group (n=6). After 12 weeks, bone regeneration was evaluated with soft X-rays, micro-computed tomography, fluorescence microscopy, and histomorphometric analysis. Four implants failed (2 each in the PCL-TCP+hUCMSCs+PRP and PCL-TCP+hUCMSC groups). An analysis of the grayscale levels and bone-implant contact ratio showed significantly higher mean values in the PCL-TCP+hUCMSCs+PRP than in the PCL-TCP group (P=0.045 and P=0.016, respectively). In fluoromicroscopic images, new bone formation around the outer surfaces of the scaffolds was observed in the PCL-TCP+hUCMSCs+PRP group, suggesting a tenting effect of the specially designed scaffolds. Bone regeneration at the scaffold-implant interfaces was observed in all 3 groups. Using a tube-shaped, honeycombed PCL-TCP scaffold with hUCMSCs and PRP may serve to enhance bone formation and dental implants' osseointegration in the procedure of simultaneous sinus lifting and dental implantation.

Influence of the biomechanical environment on the femoral stem insertion and vibrational behavior: a 3-D finite element study.

The long-term success of cementless surgery strongly depends on the implant primary stability. The femoral stem initial fixation relies on multiple geometrical and material factors, but their influence on the biomechanical phenomena occurring during the implant insertion is still poorly understood, as they are difficult to quantify in vivo. The aim of the present study is to evaluate the relationship between the resonance frequencies of the bone-implant-ancillary system and the stability of the femoral stem under various biomechanical environments. The interference fit IF, the trabecular bone Young's modulus [Formula: see text] and the bone-implant contact friction coefficient [Formula: see text] are varied to investigate their influence on the implant insertion phenomena and on the system vibration behavior. The results exhibit for all the configurations, a nonlinear increase in the bone-implant contact throughout femoral stem insertion, until the proximal contact is reached. While the pull-out force increases with [Formula: see text], IF and [Formula: see text], the bone-implant contact ratio decreases, which shows that a compromise on the set of parameters could be found in order to achieve the largest bone-implant contact while maintaining sufficient pull-out force. The modal analysis on the range [2-7] kHz shows that the resonance frequencies of the bone-implant-ancillary system increase with the bone-implant contact ratio and the trabecular bone Young's modulus, with a sensitivity that varies over the modes. Both the pull-out forces and the vibration behavior are consistent with previous experimental studies. This study demonstrates the potential of using vibration methods to guide the surgeons for optimizing implant stability in various patients and surgical configurations.

Effectiveness of photofunctionalized titanium alloy on osseointegration in rats with type 2 diabetes

BackgroundUltraviolet (UV) light-mediated photofunctionalization improves the osseointegration of pure titanium and titanium alloy (Ti6Al4V). However, little is known about the effect of UV irradiation on Ti6Al4V, used frequently in orthopedic surgery, in diabetic patients. We examined the effect of UV irradiation on Ti6Al4V in rats with type 2 diabetes.MethodsCylinder Ti6Al4V implants were used. Half the animals were Sprague Dawley rats (the control group), and the other half were Spontaneously Diabetic Torii fatty rats (the diabetes mellitus model). For radiological analysis, bone density was observed and calculated using 3D microcomputed tomography. Histological analysis was performed to calculate the bone–implant contact (BIC) ratio. We used Pearson correlation to analyze the correlation between average blood glucose level and BIC ratio, and between average blood glucose level and bone volume (BV) ratio.ResultsIn the UV light-treated group, the BIC ratios of the normal and diabetic rats increased significantly compared with those in the untreated group at 2 weeks; at 4 weeks, the BIC ratio of the diabetic rats increased significantly, but there was no significant increase in the control animals. In both the control and diabetic groups, there was no significant difference in the BV ratios between the UV-treated and untreated implants at 2 or 4 weeks. The average blood glucose level in the 4-week group negatively correlated with the BIC and BV ratios. The average blood glucose level in the UV-treated group negatively correlated with the BIC ratio.ConclusionPhotofunctionalization of Ti6Al4V implants may promote osseointegration in the early stages in rats with type 2 diabetes.

Mechanical micromodeling of stress-shielding at the bone-implant interphase under shear loading.

Inserting a titanium implant in the bone tissue may modify its physiological loading and therefore cause bone resorption, via a phenomenon called stress-shielding. The local stress field around the bone-implant interphase (BII) created under shear loading may be influenced by different parameters such as the bone-implant contact (BIC) ratio, the bone Young's modulus, the implant roughness and the implant material. A 2-D finite element model was developed to model the BII and evaluate the impact of the aforementioned parameters. The implant roughness was described by a sinusoidal function (height 2Δ, wavelength λ), and different values of the BIC ratio were simulated. A heterogeneous distribution of the maximum shear stress was evidenced in the periprosthetic bone tissue, with high interfacial stress for low BIC ratios and low implant roughness and underloaded regions near the roughness valleys. Both phenomena may lead to stress-shielding-related effects, which were concentrated within a distance lower than 0.8λ from the implant surface. Choosing an implant material with mechanical properties matching those of bone tissue leads to a homogenized shear stress field and could help to prevent stress-shielding effects. Finally, the equivalent shear modulus of the BII was derived to replace its complex behavior with a simpler analytical model in future studies. Schematic illustrations of the 2-D finite element model used in the present study and spatial variation of the maximal shear stress in the periprosthetic bone tissue for different implant roughness and bone-implant contact ratios.

Histomorphometric and biomechanical evaluation of the osseointegration around micro- and nano-level boron-nitride coated titanium dental implants

IntroductionTitanium dental implants has been coated with different materials such as polymers and biomimetic agents, bone morphogenetic protein, calcium phosphate to enhance surface properties of the titanium implants for osseointegration. The aim of this study was to evaluate the bone tissue healing around Boron Nitride-coated (BN-coated) titanium implants histomorphometrically and biomechanically and also observe the effect of different coating thicknesses on osseointegration. Materials and methodsBN was coated on dental titanium implants with two different coating thicknesses by using RF magnetron sputtering system. Totally fifty-four implants were inserted into the tibias’ of 12 New Zealand rabbits bilaterally under general anesthesia. All animals were sacrificed after 4-weeks. Bone-implant contact (BIC) and new bone area/total area ratios (BATA) were calculated. Also, the removal torque (RT) test was performed. ResultsThe highest new bone area in the medullary cavity was around the nano-BN-coated surface with 15.70%. In micro-BN-coated surface and control group, this ratio was determined as 10.48% and 8.23%, respectively. The BIC ratios in upper-side of implants and cortical-associated BIC ratios in lower-side were found significantly higher in control and micro-BN-coated group than nano-BN-coated group (p < 0.05). Similar BIC values were observed between control and micro-BN-coated groups (p > 0.05). BATA values did not show statistically significant differences between all three groups (p > 0.05). The RT values measured in all groups were found comparable and no statistically significant differences were found (p > 0.05). ConclusionNo inflammatory reaction developed around any implant. Relatively more new bone formation around nano-BN-coated titanium implants indicates the promising osseoinductive effect of BN coating. BN-coated implants showed similar biomechanical and histomorphometrical outcomes to that of the conventional titanium implants through a 4-week evaluation period.

Biomechanic and biochemical analysis of the effects of local Ankaferd Blood Stopper® application on osseointegration of titanium implants

Aim: Investigations into Ankaferd Blood Stopper® (ABS) on bone healing have revealed positive bone regeneration effects. The exact mechanism of this positive bone tissue metabolism effect is unknown. This study’s aim is a biomechanic and biochemical investigation of the effects of local ABS application on the osseointegration of titanium implants. Methodology: Sprague Dawley rats were divided into four groups of ten rats each. The control group (n=20) received no treatment during the experimental period, while the ABS group (n=20) had ABS applied locally during the surgical application of the titanium implant before insertion into the bone sockets. After 2 (controls n=10 and ABS n=10) and 4 weeks (controls n=10 and ABS n=10) experimental periods, the rats were sacrificed and implants with surrounding bone tissues were removed for reverse torque analysis (Newton), blood sample collection, and biochemical analysis. Results: The biomechanic bone implant contact ratio detected was higher in week 4 than in week 2 in the ABS group (p&lt;0, 05). Lower phosphor levels were detected in the ABS group than in the 4-week controls (p&lt;0, 05). Conclusion: According to the biomechanical parameters, ABS is more effective after four weeks than after two weeks when locally applied. How to cite this article: Özcan EC, Gül M, Tanık A, Yıldırım TT, Özkan M, Bozoğlan A, Özdemir HE, Dündar S. Biomechanic and biochemical analysis of the effects of local Ankaferd Blood Stopper® application on osseointegration of titanium implants. Int Dent Res 2022;12(1):27-33. https://doi.org/10.5577/intdentres.2022.vol12.no1.5 Linguistic Revision: The English in this manuscript has been checked by at least two professional editors, both native speakers of English.

Implant Stability Following Osseointegration of Dental Implants in Bone Sites Reconstructed with Novel Porous Titanium Scaffold

Porous titanium (porous Ti) possesses excellent mechanical strength and three-dimensional structure. Therefore, it enables bone formation due to its good osteoconduction abilities. Osseointegration can be achieved at the implant site after bone reconstruction with porous Ti. This study aimed to assess implant stability following osseointegration at sites reconstructed with porous Ti. Hollow-shaped porous Ti were placed in the tibiae of six New Zealand white rabbits. Ti dental implants were placed 4 weeks later. Implant placed at the parent bone sites, without porous Ti, served as the controls. Histological and histomorphometric assessments of the porous Ti and control sites were performed 4 weeks later. There was no significant difference in the insertion torque between the porous Ti and control groups. The primary and secondary implant stability quotient value was higher in the porous Ti group than that in the control group. Histologically, bone reconstruction was achieved with porous Ti through osteoconduction into the original bone region and bone marrow region, as osseointegration of implants was achieved even in the bone marrow region. The bone-implant contact ratio was similar in both the groups; however, the bone-implant contact was mainly in the cortical region in the control group. In the present study, the reconstructed bone site with porous Ti showed favorable osseointegration ability when the dental implant was placed. Porous Ti is expected to be a suitable material for bone material before implant placement.

The role of forkhead box class O1 during implant osseointegration.

FOXO1, a member of the forkhead family of transcription factors, plays a vital role in the osteogenic lineage commitment of mesenchymal stem cells, and affects multiple cellular functions of osteogenic cells. However, prior studies have focused on mesenchymal stem cells but not on differentiated osteoblasts. In addition, studies about the role of FOXO1 during osseointegration are lacking. In this present study, we constructed osteoblast conditional FOXO1 knock-out mice and lentivirus-mediated FoxO1 overexpression to investigate maxillary titanium implant osseointegration. After 4wk post implant placement, micro-computed tomography, histomorphometric analyses, and RT-qPCR assays were performed. Results showed that compared with the control group, overexpression of FOXO1 significantly enhanced bone formation around implant and bone-implant contact ratio, while loss of FOXO1 impaired peri-implant osteogenesis and osseointegration. Moreover, overexpression of FoxO1 enhanced expression of osteogenesis-related genes, such as Runx2, Alp1, Col1a1, and Bglap. Whereas, knock-out of Foxo1 reduced the expression of osteogenesis-related genes. Taken together, our results suggested that FOXO1 in osteoblasts could enhance osteogenesis-related gene expression to improve osseointegration.

Osseointegration Aspects of Implants at the Bone Reconstruction Site by a Novel Porous Titanium Scaffold.

ABSTRACTObjectivesPorous titanium is used for the reconstruction of large bone defects due to its excellent mechanical strength. The quality of osseointegration of implants placed in bone reconstructed with porous titanium is unknown. The purpose of this in vivo study was to evaluate the osseointegration of implants at sites reconstructed using porous titanium.Material and MethodsHollow porous titanium (Ti) (outer-diameter 6 mm, inner-diameter 2 mm, length 4 mm, 85% porosity) and similar-sized porous hydroxyapatite (porous HA: 75% porosity) samples were prepared and implanted in 6 New Zealand white rabbit femurs. Four weeks later, an implant bed was created to receive a Ti implant (diameter 2 mm, length 4 mm). An implant placed at a pristine bone site served as the control. Four weeks later, histological and histomorphometric evaluations of the test and control sites were conducted.ResultsOsseointegration was observed in all groups. There was no significant difference in the bone formation ratio and bone-implant contact (BIC) ratio across all groups for the whole area. At the cancellous bone area of the bone defect, superior bone formation ratio and BIC ratio were observed with porous Ti and porous HA compared to the control (bone formation ratio: control 1.8 [SD 3]%, HA 23 [SD 3]%, Ti 23.6 [SD 5]%; BIC ratio: control 5.4 [SD 5.3]%, HA 28.9 [SD 10.7]%, Ti 41.6 [SD 14]%). Porous Ti demonstrated good osteoconduction and osseointegration abilities, similar to porous HA.ConclusionsTo our knowledge, this is the first report of implant treatment after preliminary bone reconstruction using a titanium biomaterial. Porous titanium is a suitable material for bone reconstruction before implant treatment in load-bearing areas that allow subsequent prosthetic treatment.

Topikal D Vitamininin Titanyum İmplantların Osseointegrasyonu Üzerine Etkilerinin Değerlendirilmesi: Deneysel Bir Çalışma

Background: The aim of this study was to evaluate the effects of topical vitamin D to on osseointegration when applied to the surface of titanium implants. Material and Metods: Twenty male Spraque-Dawley rats were used in this study in a 4-week experimental period. 4 rats died during the experiments. The rats were divided into 2 groups: a test group and control group. Sixteen sandblasted and acid-etched implants were integrated surgically in the metaphyseal part of rat femurs after patella dissection. Prior to integration, the implants, which were 3.2 mm in diameter and 8 mm in length, were submerged in a 10% vitamin D solution in the test group. No treatment was applied in the control group. After the 4-week experimental period, the rats were sacrificed, and the implants were removed with surrounding bone tissue. Specimens were fixed for 7 days in a 10% formaldehyde solution. Bone implant contact (BIC) ratios were determined after using non-decalcified histological methods. Results: In the experiment, 2 samples were removed because they were not suitable. No statistically significant differences were found for BIC ratios between the test (n = 7) and control group (n = 7) implants (P&amp;gt; 0.05). Conclusion: It was concluded, within the limitations of this animal study, that topical vitamin D application on implant surfaces does not affect BIC ratios.

Effects of local application of the ankaferd blood stopper on osseointegration in three different surface titanium implants

ObjectiveResearchs of the effects of ankaferd blood stopper (ABS) on bone healing metabolism have revealed that it affects bone regeneration positively. The exact mechanism by which this positive effect on bone tissue metabolism is not known. The aim of this study is to biomechanic and biochemical analysis of the effects of the local ABS application on osseointegration of 3 different surfaced titanium implants. Material & MethodsSpraque dawley rats were divided machined surfaced (MS) (n ​= ​10), sandblasted and large acid grid (SLA) (n ​= ​10) and resorbable blast material (RBM) (n ​= ​10) surfaced implants. ABS applied locally during the surgical application of the titanium implant before insertion in bone sockets. After 4 weeks experimental period the rats sacrificed and implants with surrounding bone tissues were removed to reverse torque analysis (Newton), blood samples collected to biochemical analysis (ALP, calcium, P) ResultsBiomechanic bone implant contact ratio detected higher in SLA surfaced implants compared with the RBM and controls (P ​< ​0,05). Phosphor levels detected lower in RBM implant group compared with the controls and SLA (P ​< ​0,05). Additionally; phosphor levels detected highly in controls compared with the RBM implants. ConclusionAccording the biomechanical parameters ABS may be more effective in SLA and RBM surfaced implants when locally applied.