Blue LED Light Research Articles

Green triboelectric nanogenerator based on waste polymers for electrophoretic deposition of titania nanoparticles

Nowadays, with the development of electronic devices and the internet of things (IoT), there is a growing demand for an available, eco-friendly and endless power supply. Triboelectric nanogenerator (TENG), which converts wasted mechanical energy to electricity, is an alternative to batteries for power generation. TENGs are usually fabricated from polymers, and there are already great quantities of waste polymers in the environment that concern animals, wildlife and humans. Therefore, in this work, several eco-friendly, simple and low-cost TENGs were crafted using waste polymers like polyurethane foam (PU), expanded polystyrene (PS), polypropylene (PP), polyethylene foam (PE) and melamine formaldehyde foam (MF) without performing any physical or chemical functionalization on them. Finite element analysis was performed for each TENG and simulation results supported our experimental findings. Among these TENGs, voltage and power density of 1830 V and 96.68 mW/cm2 were achieved over a 3 × 3 cm2 area of M-TENG. This TENG could turn on 100 commercial blue light LED. The TENG with Melamine formaldehyde foam as a tribo-positive layer (M-TENG) also showed high mechanical robustness and its output did not change after 10,000 contact and separation cycles. To examine M-TENG utilization for high voltage practical application, M-TENG was used as a power source of electrophoretic deposition. The obtained high-quality titanium dioxide coating was uniform with no microcracks.

Visible-Light-Induced Deaminative Alkylation/Cyclization of Alkyl Amines with N-Methacryloyl-2-phenylbenzoimidazoles in Continuous-Flow Organo-Photocatalysis.

Herein, we present a metal-free visible-light-induced eosin-y-catalyzed deaminative strategy for the sequential alkylation/cyclization of N-methacryloyl-2-phenylbenzoimidazoles with alkyl amine-derived Katritzky salts, which provides an efficient avenue for the construction of various benzo[4,5]imidazo[2,1-a]isoquinolin-6(5H)-one derivatives in moderate to excellent yields under mild reaction conditions. The key enabling feature of this novel reaction includes utilization of redox-active pyridinium salts from abundant and inexpensive primary amine feedstocks that were converted into alkyl radicals via C-N bond scission and subsequent alkylation/cyclization with N-methacryloyl-2-phenylbenzoimidazoles by the formation of two new C-C bonds. In addition, we implemented this protocol for a variety of amino acids, affording the products in moderate yields. Moreover, the novel, environmentally benign batch protocol was further carried out in a continuous-flow regime by utilizing a perfluoroalkoxy alkane tubing microreactor under optimized reaction conditions with a blue light-emitting diode light source, enabling excellent yields and a shorter reaction time (19 min) versus the long reaction time (16 h) of the batch reaction. The reaction displays excellent functional group tolerance, easy operation, scalability, mild reaction conditions, and broad synthetic utility.

Blue LED light irradiation enhances yield in green beans

Blue LED light irradiation enhances yield in green beans

Probing Charge Carrier Properties and Ion Migration Dynamics of Indoor Halide Perovskite PV Devices Using Top‐ and Bottom‐Illumination SPM Studies

AbstractRecently, perovskite solar cells have shown excellent performance under indoor light conditions. In a new approach using directional illumination combined with nanoscale scanning probe microscopy (SPM) characterization, morphology dependent‐charge transport measurements are performed to provide a comprehensive understanding of the optoelectronic behavior of (FAPbI3)0.85(MAPbBr3)0.15 containing 5 vol% cesium (Cs5vol%) with various electron transport layers (ETLs), i.e., SnO2, c‐TiO2, and [6,6]‐phenyl‐C61‐butyric acid methyl ester/SnO2 under indoor light. This approach allows the identification of the charge transport properties of the perovskite film and the perovskite/ETL interface separately. The light is applied from the top of the perovskite film to study the electronic properties of the surface. Lower photocurrent and lower surface photovoltage (SPV) are observed under top‐illumination conditions. The electronic interface behavior is investigated using bottom‐illumination and short excitation wavelengths, such as blue LED light. Higher photocurrent and higher SPV are observed under blue light illumination from the bottom. These results suggest that the charge transport capability is enhanced near the p–n junction. Conductive atomic force microscopy results show that SnO2 enhances the charge collection properties of the perovskite's grain boundaries (GBs). Kelvin probe force microscopy results confirm that SnO2 exhibits homogeneous and high surface potential because of the lowest trap states at GBs.

Mechanical and antimicrobial effects of riboflavin-mediated photosensitization of in vitro C. albicans formed on polymethyl methacrylate resin

PurposeThis study assessed the potential of riboflavin-mediated photodynamic therapy (RF-PDT) against Candida albicans (C. albicans) and compared the effects of RF-PDT with other therapeutic modalities in terms of mechanical and surface characteristics of acrylic denture base material. Materials and methodsMolds (10 × 10 × 2 mm) of acrylic resin specimens were prepared and underwent artificial ageing. C. albicans were grown aerobically over the specimens and divided into four groups (n = 10/group); Group-I: no decontamination; Group-II: nystatin suspension; Group-III: riboflavin 0.1% in darkness, Group-IV: blue LED light only, and Group-V: riboflavin 0.1% for 10 minutes (pre-irradiation time) and photoactivated by the blue LED light (light dose). Fungal viability was assessed using MTT assay and characterized using scanning electron microscopy and confocal laser microscopy (CLSM). Treated specimens were subjected to surface roughness (Ra), flexural strength (FS), and flexural modulus (FM). ResultsGroup-I showed the highest C. albicans viability followed by Group-III. Nystatin group (Group-II) showed ∼50% of the viability while RF-PDT showed the least C. albicans viability among the four groups (p<0.05). On SEM, specimens treated with Group-IV and V showed almost clear and free from C. albicans that was evidenced on CLSM. Post-treated specimens and storage after 72 h revealed that FS was significantly higher for RF-PDT group as compared to any other group (>105.82 MPa) (p<0.05). The FM and Ra showed statistically no significant difference between the groups (p>0.05). ConclusionRF-PDT showed the highest anti-fungal capacity against C. albicans over acrylic denture surface without any surface deterioration.

Study on Irradiation Uniformity of Array Blue LED in Jaundice Treatment Box

The uniformity of blue LED array in jaundice treatment box is improved. The mathematical model of illumination uniformity algorithm for inner and outer LED arrays layout is established. Taking the actual size of blue light board in jaundice treatment box as an example, the optimal illumination uniformity with best LED arrays layout are obtained through programming iteration and simulation verification. The uniformity of blue light LED improved 42.9 % comparing with tradition LED arrays.

A novel M2Ga2GeO7:N3+ (M = Ca, Ba, Sr; N = Cr, Nd, Er) sub-micron phosphor with multiband NIR emissions: preparation, structure, properties, and LEDs

Near-infrared (NIR) emission materials can be widely applied in various fields, such as food detection, imaging, treatment, electronic products. With the trend of miniaturization of equipment, smaller materials are needed. In this work, we successfully synthesized a series of M2Ga2GeO7:N3+ (M = Ca, Ba, Sr; N = Cr, Nd, Er) samples and then focused on the study of Nd3+ doped Sr2Ga2GeO7 (SGGO). A series of SGGO:xNd3+ sub-micron phosphors were prepared via a microwave-assisted sol–gel process combined with subsequent calcination at 750 ℃, and the structural information and luminescent properties were systematically studied. SGGO is a representative tetragonal crystal and belonging to the space group of P21m (113). The Nd3+ ions occupy eight-coordinated Sr2+ sites in the crystal lattice. From SEM analysis, the average particle size distribution is 219.7 ± 41.4 nm. The sub-micron phosphors have rich excitation spectra ranging from 350 nm to 850 nm and can produce multiband NIR emissions of 1331, 1056, and 905 nm when excited by ultraviolet and NIR light. The maximum emission intensity was obtained by optimizing the doping ratio of Nd3+ ions. A commercial chip was then utilized to fabricate light-emitting diodes (LEDs) to verify its application potential in NIR-II mini-LEDs. Compared with blue light LEDs, the as-prepared LEDs had good imaging penetration depth and could be clearly observed under 10 mm of chicken breast coverage. The maximum imaging penetration depth can be 33 mm.

Embryo Development and Behavior in Sea Urchin (Tripneustes gratilla) Under Different Light Emitting Diodes Condition

This study aims to evaluate the effect of light-emitting diodes (LEDs) of different wavelengths on the embryonic development, covering behavior, righting behavior, and phototaxis of collector urchins (Tripneustes gratilla). The collector urchins were divided into three groups according to the type of LED illumination they received: full-spectrum (400–750 nm wavelength), red light (630 nm), or blue light (450 nm). The results of the embryonic development experiment indicated that the blue LED group had the highest proportion of embryos reaching the prism stage at the 24th hour and the highest proportion of embryos entering the 4-arm pluteus stage, but it also had the highest death rate at the 48th hour. The full-spectrum and red LED groups exhibited similar speeds of embryonic development. In the experiment on covering behavior performed on adult urchins, our findings indicated that the blue LED group gripped the most acrylic sheets for cover, exhibiting the most covering behavior, followed by the full-spectrum group and then the red LED group. Moreover, behavior varied with coloration, as collector urchins with a lower level of melanin exhibited more covering behavior than those with a higher melanin level. In addition, the righting behavior experiments demonstrated that the blue LED group spent the longest time righting themselves. It is possible that the relatively strong stimulation from the blue LED illumination led to a higher level of stress in the collector urchins and hence slowed their righting. The phototaxis experiment revealed the most significant negative phototactic response in collector urchins when they were under the blue LED light, followed by the full-spectrum light; the red LED light did not induce any positive or negative phototactic response in the collector urchins. This experimental result verified collector urchins’ high sensitivity to and dislike of the blue LED light. The study results confirmed that the blue LED light environment accelerated the embryonic development of collector urchins; however, the relatively strong stimulation from that light also caused them to engage in covering behavior or move away from the light. These results indicate that short-wavelength irradiation significantly affects the embryonic development and behavior pattern of this species.

One-Pot Microwave-Assisted Synthesis of Carbon Dots and in vivo and in vitro Antimicrobial Photodynamic Applications.

Carbon-based photosensitizers are more attractive than the other ones based on their low cost, high stability, broadband of light absorption, tunable emission spectra, high quantum yield, water solubility, high resistance to metabolic degradation, and selective delivery. These properties allow multiple applications in the field of biology and medicine. The present study evaluated in vitro and in vivo the antimicrobial photodynamic effect of a one-pot microwave produced C-DOTS based on citric acid. The in vitro assays assessed the effectiveness of illuminated C-DOTS (C-DOTS + light) against Staphylococcus aureus suspension and biofilm. The concentrations of 6.9 and 13.8 mg/mL of C-DOTS and light doses of 20 and 40 J/cm2 were able to reduce significantly the microorganisms. Based on these parameters and results, the in vivo experiments were conducted in mice, evaluating this treatment on wounds contaminated with S. aureus. The viability test showed that C-DOTS–mediated photodynamic inactivation reduced 104 log of the bacteria present on the skin lesions. These results, altogether, showed that antibacterial photodynamic therapy using C-DOTS is a promising and viable treatment for Gram-positive bacteria-infected wounds.

Green Stereoregular Polymerization of Poly(methyl methacrylate)s Through Vesicular Catalysis

Green Stereoregular Polymerization of Poly(methyl methacrylate)s Through Vesicular Catalysis

Red and Blue Light-Emitting Diodes Significantly Improve in vitro Tuberization of Potato (Solanum tuberosum L.)

Abstract The tuberization phenomenon in potatoes (Solanum tuberosum L.) is a highly synchronized morphophysiological process occurring on the underground stolons under the influence of various intrinsic and extrinsic factors. This involves the participation of the phytochrome sensory system, transport of sucrose from source to stolon, and several regulatory pathways including tuber-inducing hormone biosynthetic lipoxygenase (StLOX1) gene and major calcium-mediated signaling pathway genes (StCDPK and StCaM1). This study was aimed to explore the impacts of distinctive qualities of the light-emitting diode (LED) light with a specific wavelength on in vitro tuberization of potato. Single nodal segments of potato ‘Kufri Jyoti’ were incubated in vitro on the growth medium at a temperature of 22 ± 2 °C and exposed to various combinations of red (R) and blue (B) LED light. The results showed that the combination of 30% red + 70% blue LED light (R30B70) significantly shortened the tuber induction period, increased the number of tubers, and their yield compared with these parameters in the tissues exposed to the white light (W100). The induction of the in vitro tuberization correlated with the enhanced expression of the major tuberizing pathway genes, including the lipoxygenase (StLOX1), calmodulin (CaM1), and calcium-dependent protein kinase (StCDPK). The current study indicated that the combination of red and blue LED lights at R30B70 is the best spectrum for effective in vitro tuberization of potatoes.

Environmentally Friendly, Photochemical Access to [ ]AuIII Pincer Complexes By Oxidative Addition.

Starting from commercially available DMSAuCl and diazonium salts, cationic [N∧C∧N ]AuIII complexes were synthesized in a selective, photosensitizer‐free, photochemical reaction by irradiation with blue LED light. This new protocol represents the first easy synthesis of these types of pincer complexes in moderate to excellent yield starting from a readily available gold(I) precursor with nitrogen as the only by‐product. Owing to the disadvantages of known protocols, especially the toxicity in the case of a transmetalation with mercury or the necessity for a mostly twofold excess of a gold precursor, this method offers an attractive alternative towards this kind of gold(III) complexes. In addition, the first arylated [N∧C∧N ]Au(III) pincer complex was synthesized by using this technology.

(Invited) Titania Inverse-Opal Photonic Crystals Incorporating Gold Nanoparticles in Void Spaces for Photoabsorption Enhancement

Designing of three-dimensional (3D) materials such as inverse-opal (IO) photonic crystals (PCs) has been identified as an effective pathway to enhance light harvesting to longer electromagnetic absorption regions such as visible and infrared [1]. IO PCs exhibit photonic band gap (PBG) and this band structure predicts the translation of photons with reduced velocity, namely as slow photons at certain crystallographic directions. The photonic effect from titania (TiO2)-IO structure was reported to enhance light-material interactions thus allowing better absorption of light at the wavelength at which the materials absorb poorly [2]. On the other hand, utilization of gold-nanoparticles (Au-NPs) on TiO2 could aid in charge separation and play its role as an amplifier for visible-light absorption due to its effects originating from localized surface plasmon resonance (LSPR) [3]. In this study, TiO2-IO PC with incorporated gold nanoparticles(Au-NPs) per void space was developed by implementing five important steps to achieve a good quality of TiO2-IO structure. Both photonic effects due to the slow photons in TiO2-IO structure and LSPR effects contributed by Au-NPs were expected to give visible-light absorption by the photocatalyst material.The experimental procedure consists of five steps as shown in Scheme 1 starting from (i) synthesis of Au-NPs, (ii) silica (SiO2) coating on Au-NP to form Au/SiO2 core-shells, (iii) self-assembly of Au/SiO2 to form high-quality opal structure, (iv) infiltration of TiO2 precursor via forced impregnation method and (v) selective etching of SiO2 to obtain the final TiO2-IO structure. Photodegradation of acetic acid was carried out in the presence of the photocatalyst material by using blue LED light (450 nm) with optical power of 0.3 W. SiO2 containing Au-NP (Au/SiO2) was used as the opal template for the 3D macroporous TiO2-IO containing Au-NP per void space (TiO2(Au)-IO). Figures 1a and 1b are images observed for Au/SiO2 opal structure exhibiting face-centered cubic (FCC) arrangement. As is observed, the closely packed opal structure could be obtained as the minimum variation among each particle was less than 5 %. However, extra precautions should be taken to avoid cracking on the opal structure to sustain the quality of the final desired material. Figures 1c and 1d are images of TiO2(Au)-IO which was successfully obtained after TiO2 infiltration via forced impregnation method followed by the removal of SiO2 to form the nanovoids. The strategy that has been implemented to enhance the light harvesting process was by designing the TiO2-IO structure with different diameter of nanovoids, which can be controlled by altering the SiO2 shell thickness in the second step of the synthesis process.Photocatalytic activities of those samples were evaluated by measuring the amount of carbon-dioxide(CO2) generated from acetic acid by TiO2(Au)-IO with different diameter of nanovoid diameters (Au-NP size: 44 nm) under LED light irradiation (4 h). Enhanced CO2 evolution was detected with TiO2(Au)-IO with nanovoid diameter of 215 nm suggesting the successful matching of photonic and LSPR effects in TiO2(Au)-IO.[1] X. Zheng, D. Li, X. Li, L. Yu, P. Wang, X. Zhang, J. Fang, Yu. Shao and Y. Zheng. Phys. Chem. Chem. Phys. 16 (2014) 15299–15306.[2] V. Jovic, H. Idriss and G.I.N. Waterhouse. Chem. Phys. 479 (2016) 109–121.[3] S.M. Yoo, S.B. Rawal, J.E. Lee, J. Kim, H. Ryu, D. Park and W.E. Lee. Appl. Catal. A Gen. 499 (2015) 47–54. Figure 1

LED Light Technology as a Source of Illumination and a Promising Method for Stevia rebaudiana Elite Propagation

Effect of light-sources, quality, and intensities on morphogenesis, shoot multiplication, development and roots, and biomass production in Stevia investigated using shoot tips cultured on Murashige and Skoog (MS) medium supplemented with different concentrations of plant growth regulators (PGRs). 2000 Lux intensity provided by fluorescent light lambs was found the most favorable for shoot induction and production, shoot length, number of leaves/explant and also for fresh and dry weights/foliage. Under this light condition, the optimum contents of photosynthetic pigments, cholorophyll a, cholorophyll b, total cholorophyll, and carotenoids recorded. Blue-LED light treatment created growth condition for the highest shoot elongation, leaves number/shoot, leaf fresh weight, leaf dry weight, and photosynthetic pigment production. Cent percent of shoot induction was obtained under red-LED treatment resulting in the largest number of shoot production. Root formation was promoted by 2000 and 3000 Lux intensities of light. However, the 2000 Lux intensity treatment provided the most favorable growth condition permitting generation of largest number of longest roots with maximum fresh/dry weights. Root induction was 100 percent under fluorescent light, the maximum fresh and dry weights of roots were achieved on blue-Led light and red-LED treatment induced the longest roots.

Effect of Light Intensity and Wavelength on Biomass Growth and Protein and Amino Acid Composition of Dunaliella salina

Dunaliella salina is a halotolerant, photoautotrophic marine microalga and one of the richest sources of natural carotenoids but also shows potential as a novel food source with high protein quality. This study sought to optimise the production of biomass, protein and amino acids from D. salina, alongside carotenoids using a two-stage cultivation approach based on the use of light of different intensities and quality, i.e., white, red and blue LED light. In stage 1, four white LED light intensities were tested. In stage 2, the same four light intensities from either blue or red LEDs were applied once exponential growth ceased and cells reached the stationary phase under white LED light in stage 1. Remarkably, both biomass concentration and biomass productivity showed a 1.3–1.7-fold increase in stage 2, without medium replenishment, while protein concentration and protein productivity showed an ~1.1-fold increase. The amino acid content and amino acid index remained unchanged from stage 1 to stage 2, and minimum difference was found across different light intensities. Overall, D. salina delivered so-called high protein quality, with an essential amino acid index (EAAI) of 0.99, and red light, which has previously been shown to increase carotenoid production, boosted further biomass production over and above white light, at all light intensities tested.

Effect of blue LED light irradiation on anthocyanin synthesis in the skin of detached apples

Effect of blue LED light irradiation on anthocyanin synthesis in the skin of detached apples

Photophysical and Antibacterial Properties of Porphyrins Encapsulated inside Acetylated Lignin Nanoparticles.

Lignin has recently attracted the attention of the scientific community, as a suitable raw material for biomedical applications. In this work, acetylated lignin was used to encapsulate five different porphyrins, aiming to preserve their photophysical properties, and for further use as antibacterial treatment. The obtained nanoparticles were physically characterized, through dynamic light scattering size measurement, polydispersity index and zeta potential values. Additionally, the photophysical properties of the nanoparticles, namely UV-vis absorption, fluorescence emission, singlet oxygen production and photobleaching, were compared with those of the free porphyrins. It was found that all the porphyrins were susceptible to encapsulation, with an observed decrease in their fluorescence quantum yield and singlet oxygen production. These nanoparticles were able to exert an effective photodynamic bactericide effect (blue-LED light, 450–460 nm, 15 J/cm2) on Staphylococcus aureus and Escherichia coli. Furthermore, it was achieved a photodynamic bactericidal activity on an encapsulated lipophillic porphyrin, where the free porphyrin failed to diminish the bacterial survival. In this work it was demonstrated that acetylated lignin encapsulation works as a universal, cheap and green material for the delivery of porphyrins, while preserving their photophysical properties.

Microbicidal effect of 405-nm blue LED light on Candida albicans and Streptococcus mutans dual-species biofilms on denture base resin.

This study investigated: (1) the microbicidal effect of 405-nm blue LED light irradiation on biofilm formed by Candida albicans hyphae and Streptococcus mutans under dual-species condition on denture base resin, (2) the generation of intracellular reactive oxygen species (ROS) induced by irradiation, and (3) the existence of intracellular porphyrins, which act as a photosensitizer. Denture base resin specimens were prepared and C. albicans and S. mutans dual-species biofilms were allowed to form on the specimens. The biofilms were irradiated with 405-nm blue LED light and analyzed using the colony-forming unit assay, fluorescence microscopy, and scanning electron microscopy (SEM). Single-species biofilms of C. albicans and S. mutans formed on the specimens were irradiated with 405-nm blue LED light. After the irradiation, the intracellular ROS levels in C. albicans and S. mutans cells were measured. In addition, the level of intracellular porphyrins in C. albicans and S. mutans were measured. Irradiation for more than 30min significantly inhibited the colony formation ability of C. albicans and S. mutans. Fluorescence microscopy revealed that almost all C. albicans and S. mutans cells were killed by irradiation. SEM images showed various cell damage patterns. Irradiation led to the generation of intracellular ROS and porphyrins were present in both C. albicans and S. mutans cells. In conclusion, irradiation with 405-nm blue light-emitting diode light for 40min effectively disinfect C. albicans hyphae and S. mutans dual-species biofilms and possibly react with intracellular porphyrins resulting in generation of ROS in each microorganism.

Follow-up of pressure ulcer treatment with photodynamic therapy, low level laser therapy and cellulose membrane

A pressure ulcer (PU) is an area of tissue trauma caused by continuous and prolonged pressure, often associated with hospitalised patients immobilised due to neurological problems, negatively affecting their quality of life, and burdening the public budget. The aim of this study was to report the follow-up, for 45 weeks, of three patients with neurological lesions due to trauma who subsequently developed PUs, and who were treated with a combination of photodynamic therapy (PDT), low level laser therapy (LLLT) and cellulose membrane (CM). PDT was mediated by the photosensitiser curcumin on a 1.5% emulsion base. Blue LED light at 450 nm was delivered continuously for 12 minutes at an irradiance of 30mW/cm2 and total energy delivered to the tissue was 22J/cm2. LLLT was performed with 660 nm laser, punctuated and continuous, twice a week with parameters: spot size 0.04cm2, power of 40mW, 10 seconds per point, fluence of 10J/cm2 and irradiance of 1000mW/cm2. All PUs had a significant reduction (range: 95.2-100%) of their area after 45 weeks of follow-up and two PUs had complete healing at 20 weeks and 30 weeks. All of the PUs showed a reduction in contamination with the PDT treatments in different proportions. From the results obtained, we conclude that the combination of PDT, LLLT and CM is a promising treatment for PU healing.

Generation of Transgenic Medaka Oryzias curvinotus (Nichols &amp; Pope, 1927) Carrying a Cyan Fluorescent Protein Gene Driven by Alpha Actin Promoter

The study aimed to produce fluorescent protein transgenic medaka Oryzias curvinotus (Nichols &amp; Pope, 1927) as a novel strain of ornamental fish. These fish were produced by transferring a plasmid consisting of a fluorescent reporter gene and a strong promoter into one-cell stage embryos. For this purpose, myosin light chain 2, but not other promoters, was mainly used. The study also evaluated the stability of the transgenic medaka germline acquiring vivid fluorescent phenotypes via the transgenesis of the cyan fluorescent protein (CFP) gene under the control of O. curvinotus skeletal alpha-actin (OCacta) promoter. The pOCacta-CFP plasmid, containing a OCacta promoter and CFP reporter gene, was transferred into the one-cell stage of O. curvinotus embryos by a microinjection technique. As a result, 36 of 1386 microinjected O. curvinotus embryos exhibited CFP signals in their trunks. The expressed CFP signals in O. curvinotus embryos and adults were detected under a microscope using a green fluorescent protein (GFP) filter (450–490 nm wavelength), and blue LED light (400–450 nm wavelength). Five O. curvinotus founders showing clear CFP signals were selected and crossed with non-transgenic counterparts to produce subsequent generations. Among strains, the frequency of germline transmission from founder to F1 was highly variable. Only two of the five founders successfully pass the transgene to the F1 generation. At present, the progeny of subsequent generations is being produced and tested for the expression of CFP signals, and therefore, stable lines are ongoing.