Bistatic Interferometric Synthetic Aperture Radar Research Articles

Estimation and Analysis of Glacier Mass Balance in the Southeastern Tibetan Plateau Using TanDEM-X Bi-Static InSAR during 2000–2014

In recent decades, glaciers in the southeastern Tibetan Plateau (SETP) have been rapidly melting and showing a large scale of glacier mass loss. Due to the lack of large-scale, high-resolution, and high-precision observations, knowledge on the spatial distribution of the glacier mass balance and the response to climate change is limited in this region. We propose a TanDEM-X bi-static InSAR (Interferometric Synthetic Aperture Radar) algorithm with a non-local mean filter method and difference strategy, to improve the precision of glacier surface elevation change detection. Moreover, we improved the glacier mass balance estimation algorithm with a correction method for multi-source system errors and an uncertainty evaluation method based on error propagation theory to reduce the uncertainty of estimations. We used 13 pairs of TanDEM-X bi-static InSAR images to obtain the glacier mass balance data for the entire SETP. The total area of glaciers monitored was 5821 km2 and the total number of glaciers monitored was 2321; the glacier surface elevation change rate was −0.505 ± 0.005 m/yr, and the glacier mass balance estimation was −454.5 ± 13.1 mm w.eq. during 2000–2014. Additionally, we analyzed the spatial distribution of the glacier mass balance within the SETP using the sub-watershed analysis method. The results showed that the mass loss rate had a decreasing trend from the southeast to the northwest. Furthermore, the temperature change and the glacier mass loss rate showed a positive correlation from the southeast to the northwest in this region. This study greatly advances our understanding of the regularities of glacier dynamics in this region, and can provide scientific support for major national goals such as the rational utilization of surrounding water resources and construction of important transportation projects.

Unmanned Airborne Bistatic Interferometric Synthetic Aperture Radar Data Processing Method Using Bi-Directional Synchronization Chain Signals

The bistatic Interferometric Synthetic Aperture Radar (InSAR) system can overcome the physical limitations imposed by the baseline of monostatic dual-antenna InSAR. It provides greater flexibility and can enhance elevation measurement accuracy through a well-designed baseline configuration. Unmanned aerial vehicles (UAVs) equipped with bistatic InSAR, having relatively low cost and high flexibility, are useful for mapping and land resource exploration. However, due to challenges including spatiotemporal synchronization and motion errors, there are limited reports on UAV-borne bistatic InSAR. This paper proposes a comprehensive method for processing data from small UAV-borne bistatic InSAR by integrating two-way synchronization chain signals. The proposed method includes compensation for time and phase synchronization errors, trajectory refinement with synchronized chain and Position and Orientation System (POS) data, high-precision bistatic InSAR imaging, and interferometric processing. Height inversion results based on the proposed method are also provided, which demonstrate the effectiveness of the proposed method in improving the accuracy of interferometric measurement at calibration points from 0.66 m to 0.42 m.

A High-Precision Target Geolocation Algorithm for a Spaceborne Bistatic Interferometric Synthetic Aperture Radar System Based on an Improved Range–Doppler Model

A trend in the development of spaceborne Synthetic Aperture Radar (SAR) technology is the shift from a single-satellite repeated observation mode to a multi-satellite collaborative observation mode. However, current multi-satellite collaborative geolocation algorithms face challenges, such as geometric model mismatch and poor baseline estimation accuracy, arising from highly dynamic changes among multi-satellites. This paper introduces a high-precision and efficient geolocation algorithm for a spaceborne bistatic interferometric SAR (BiInSAR) system based on an improved range–Doppler (IRD) model. The proposed algorithm encompasses three key contributions. Firstly, a comprehensive description of the spatial baseline geometric model unique to the bistatic configuration is provided, with a specific focus on deriving the perpendicular baseline expression. Secondly, IRD geolocation functions are established to meet the specific requirements of the bistatic configuration. Then, a novel BiInSAR geolocation algorithm based on the IRD’s functions is proposed, which can significantly improve the target geolocation accuracy by modifying the range–Doppler equation to suit the bistatic configuration. Meanwhile, a low-coupling parallel calculation method is proposed, which can improve the calculation speed by two to three times. Finally, the accuracy and efficiency of the algorithm are demonstrated using experimental data acquired by the TH-2 satellite, which is China’s first spaceborne BiInSAR system. The experimental results prove that the IRD algorithm exhibits geolocation accuracy with an average error of less than 1 m and a standard deviation of less than 2.5 m while maintaining computational efficiency at a calculation speed of 1,429,678 pixels per second.

INVESTIGATIONS ON INSAR DATA PROCESSING STANDARD FOR VOLCANO ISLAND MONITORING IN INDONESIA

Abstract. In critical situations such as disaster and humanitarian relief, the reliable geospatial data will present an appropriate decision on a timely manner. As fundamental datasets, large-scale topographic maps are are mandatory in order to perform geospatial analysis for many societal challenges. Indeed, Large Scale Topographic Mapping in Indonesia shall be accelerated in an innovative and productive way to consider the production efficiency, especially for the geospatial data acquisition as its primary source. Interferometric Synthetic Aperture Radar (InSAR) data acquisition presents some advantages, especially in conjunction with the security clearance and global weather as some main constraints for the geospatial data acquisition. In terms of disaster preparedness and emergency response, radar interferometry techniques can play an important role by generating a Digital Elevation Model (DEM) as an input to Decision Support Systems (DSS). In addition, the techniques of differential Interferometric Synthetic Aperture Radar (D-InSAR) can provide the earth surface deformation from time series Radar Datasets. A set of standards related to the InSAR data acquisition are essential, especially with regards to the improved sensors, and processing methods implemented by the worldwide space agencies nowadays. Hence, the precise definition of a standard is fundamental in order to prepare the InSAR data as one potential source of geospatial data and information, especially for LSTM data production. Generated time series of Digital Elevation Model (DEM) can identify the potential cause of 2018’s Sunda Strait tsunami (Tampubolon, 2019). It was related with the increasing eruption activity of Anak Krakatau (Child of Krakatoa). From DEM analysis, the Volcanic mudflow material avalanche has been detected before the tsunami hit the coastal surrounding area. In this paper, more advanced techniques was investigated by the combination between Time Series DEM Analysis and Ground Displacement detection. The focus on the integration between reliable TanDEM-X and up-to-date Sentinel 1A/B was proposed on another volcano island of Gamalama in Ternate. As TanDEM-X uses X-band as its medium wave, it can produce more reliable DEM as a reference data. On the other hand, Sentinel 1 uses C-band that can contribute to detect the ground deformation over the aforementioned volcano island. TanDEM-X uses a more robust and consistent approach to scan the earth surface by single data acquisition scheme, which is generally more accurate and reliable for the DEM generation. However, many factors influence the selection of a platform that can be best suited for radar interferometry. Initially, the German TanDEM-X Coregistered Singlelook Slant-range Complex (CoSSC) using bi-static InSAR approach has been implemented in order to generate DEMs comply with the LSTM specification in Indonesia. The basic principle is performing a simultaneous measurement of the same scene and identical doppler spectrum by using 2 sensors, thereby avoiding temporal decorrelation (DLR, 2012). Subsequently, the differential InSAR techniques by using Sentinel 1A/B has been performed in order to detect the ground deformation. Finally, tt can be shown that the reliable TanDEM-X data has increased the ground deformation resolution and accuracy in order to provide potential solution for disaster preparedness.

Fast geolocation solution for bistatic interferometric synthetic aperture radar configuration of inclined geosynchronous transmitter with low earth orbit receivers

AbstractSpaceborne interferometric synthetic aperture radar (InSAR) technology is an effective method to obtain digital elevation model (DEM) data. The bistatic InSAR configuration of the inclined‐geosynchronous (InGEO) transmitter with low earth orbit (LEO) receivers (InGEO‐LEO) is a novel InSAR system to acquire terrain information. This novel system is characterised with high resolution, wide swath and timeliness, but the Newton iterative method is time‐consuming to solve the bistatic InSAR equations for fast DEM generation. For the conventional LEO bistatic InSAR system, the closed‐form solution is an effective method to improve the efficiency of solving InSAR equations, which is invalid in the InGEO‐LEO InSAR system because of the significant geometry difference caused by the orbits of InGEO transmitter and LEO receivers. To address this issue, we analyse the bistatic InGEO‐LEO geometry in detail and exploit the bistatic InSAR equations to propose an approximate closed‐form solution (ACS) for the novel system. Compared with the general Newton iterative method, the ACS significantly improves the efficiency of geolocation for the bistatic InGEO‐LEO InSAR system with high precision. Simulation experiments are carried out to verify the effectiveness and superiority of ACS.

Deep Learning for Mapping Tropical Forests with TanDEM-X Bistatic InSAR Data

The TanDEM-X synthetic aperture radar (SAR) system allows for the recording of bistatic interferometric SAR (InSAR) acquisitions, which provide additional information to the common amplitude images acquired by monostatic SAR systems. More concretely, the volume decorrelation factor, which can be derived from the bistatic interferometric coherence, is a reliable indicator of the presence of vegetation and it was used as main input feature for the generation of the global TanDEM-X forest/non-forest map, by means of a clustering algorithm. In this work, we investigate the capabilities of deep Convolutional Neural Networks (CNNs) for mapping tropical forests at large-scale using TanDEM-X InSAR data. For this purpose, we rely on a U-Net architecture, which takes as input a set of feature maps selected on the basis of previous preparatory works. Moreover, we design an ad hoc training strategy, aimed at developing a robust model for global mapping purposes, which has to properly manage the large variety of different acquisition geometries characterizing the TanDEM-X global data set. In addition to detecting forest/non-forest areas, the CNN has also been trained to detect water surfaces, which are typically characterized by low values of coherence. By applying the proposed method on single TanDEM-X images, we achieved a significant performance improvement with respect to the baseline clustering approach, with an average F-score increase of 0.13. We then applied such a model for mapping the entire Amazon rainforest, as well as the other tropical forests in Central Africa and South-East Asia, in order to test its robustness and generalization capabilities, and we observed that forests are typically well detected as contour closed regions and that water classification is reliable, too. Finally, the generated maps show a great potential for mapping temporal changes occurring over forested areas and can be used for generating large-scale maps of deforestation.

A Novel DEM Block Adjustment Method for Spaceborne InSAR Using Constraint Slices.

The lack and uneven distribution of Ground Control Points (GCPs) will lead to the deterioration of Digital Elevation Model (DEM) block adjustment results in the bistatic Interferometric Synthetic Aperture Radar (InSAR) system. Given this issue, we first explain the relationship between the stability of adjustment parameters and the GCP distribution pattern theoretically using matrix perturbation theory. Second, we put forward the Constraint Slices (CSs) concept and first introduce CSs into the adjustment optimization model as constraint conditions rather than actual values as GCPs. Finally, we propose a novel DEM block adjustment method for spaceborne InSAR using CSs based on an optimization model with nonlinear constraints. The simulated experiment shows the instability of the conventional method and validates the proposed method under different parallel baseline errors. Four groups of real experiments were carried out according to the size of the uncontrolled area using twelve Co-registered Single-look Slant–range Complex (CoSSC) datasets for Henan Province, China. The adjustment results verified by the ICESat-2 ATL08 data demonstrate that the performance of the proposed method is better than the conventional method in the uncontrolled area; the corresponding improvements in adjustment accuracies compared with the conventional method are 0.13 m, 1.02 m, 2.12 m, and 8.18 m, respectively. At the same time, the proposed method can enhance the height consistency in overlapping areas, which is vital for seamless DEM production.

Fast Geolocation Solution and Accuracy Analysis for Bistatic InSAR Configuration of Geostationary Transmitter With LEO Receivers

To obtain digital elevation model (DEM) data through spaceborne interferometric synthetic aperture radar (InSAR) technology, the solution of nonlinear InSAR geolocation equations is one of the most important steps. On one hand, Newton iterative method is time-consuming to solve the equations. On the other hand, the conventional closed-form solution for low earth orbit (LEO) bistatic InSAR system is not suitable for the novel InSAR configuration of geostationary (GEO) transmitter with LEO receivers because of the significant geometry difference. To address these issues, this letter analyzes the bistatic GEO-LEO geometry in detail and exploits the bistatic InSAR equations to propose a GEO-LEO fast location method (GFLM), which obtains the effective closed-form solution for the novel system. Compared with the general Newton iterative method, the GFLM significantly improves the efficiency of geolocation for the bistatic GEO-LEO InSAR system with high precision. Moreover, the geolocation accuracy of the novel system under realistic parameters uncertainties is introduced. Finally, we carry out simulation experiments to verify the effectiveness and superiority of GFLM.

High-resolution topography of the Antarctic Peninsula combining the TanDEM-X DEM and Reference Elevation Model of Antarctica (REMA) mosaic

Abstract. The Antarctic Peninsula (AP) is one of the widely studied polar regions because of its sensitivity to climate change and potential contribution of its glaciers to global sea level rise. Precise digital elevation models (DEMs) at a high spatial resolution are much demanded for investigating the complex glacier system of the AP at fine scales. However, the two most recent circum-Antarctic DEMs, the 12 m TanDEM-X DEM (TDM DEM) from bistatic interferometric synthetic aperture radar (InSAR) data acquired between 2013 and 2014 and the Reference Elevation Model of Antarctica mosaic (REMA mosaic) at an 8 m spatial resolution derived from optical data acquired between 2011 and 2017 have specific individual limitations in this area. The TDM DEM has the advantage of good data consistency and few data voids (approx. 0.85 %), but there exist residual systematic elevation errors such as phase-unwrapping errors in the non-edited DEM version. The REMA mosaic has high absolute vertical accuracy, but on the AP it suffers from extended areas with data voids (approx. 8 %). To generate a consistent, gapless and high-resolution topography product of the AP, we fill the data voids in the TDM DEM with newly processed TDM raw DEM data acquired in austral winters of 2013 and 2014 and detect and correct the residual systematic elevation errors (i.e., elevation biases) in the TDM DEM with the support of the accurately calibrated REMA mosaic. Instead of a pixelwise replacement with REMA mosaic elevations, these provide reference values to correct the TDM elevation biases over entire regions detected through a path propagation algorithm. The procedure is applied iteratively to gradually correct the errors in the TDM DEM from a large to small scale. The proposed method maintains the characteristics of an InSAR-generated DEM and is minimally influenced by temporal or penetration differences between the TDM DEM and REMA mosaic. The performance of the correction is evaluated with laser altimetry data from Operation IceBridge and ICESat-2 missions. The overall root mean square error (RMSE) of the corrected TDM DEM has been reduced from more than 30 m to about 10 m which together with the improved absolute elevation accuracy indicates comparable values to the REMA mosaic. The generated high-resolution DEM depicts the up-to-date topography of the AP in detail and can be widely used for interferometric applications as well as for glaciological studies on individual glaciers or at regional scales.

DSM generation with bistatic TanDEM-X InSAR pairs and quality validation in inclined topographies and various land cover classes

In 2007, synthetic aperture radar (SAR) imaging was modified by TerraSAR-X (TSX); this second-generation SAR satellite offers up to 1 m of spatial resolution. The satellite is capable of interferometric SAR (InSAR), which permits the generation of digital surface models (DSMs). TSX was designed for monostatic InSAR imaging, but the potential for acquired DSMs is limited due to the disadvantages of repeat-pass InSAR geometry under the influence of temporal and related spectral decorrelations. In 2010, TanDEM-X (TDX) was launched to operate in a synchronized helix orbit with TSX to achieve high-quality DSMs covering almost the entire World in the basis of bistatic SAR imaging. In this paper, we focused on the DSM potential of TDX InSAR pairs in inclined topographies, and open, built-up, and forest land cover classes. A 5-m gridded TDX DSM was generated by interferometric processing and comprehensively analyzed by using model-to-model comparison approaches utilizing a reference airborne laser scanning (ALS) DSM. Absolute and relative vertical accuracies were estimated separately for all land cover classes using standard deviation and normalized median absolute deviation considering the influence of terrain tilt. Coherence with the reference DSM was determined by vertical profiles and frequency distribution graphics of height differences. Inaccurate regions were visualized by the generation of height error maps (HEMs). During the analysis, the qualities of the generated 5-m TSX DSM and a freely available 1-arcsecond (~ 30 m) Shuttle Radar Topography Mission (SRTM) DSM were validated and compared with TDX.

Glacier mass changes over Duxueshan, Burog Kangri, and Zangser Kangri in the Inner Tibetan Plateau

The variation of glacier mass balance during the past decades remains poorly known for Duxueshan, Burog Kangri, and Zangser Kangri (DBZ) which are located in the Inner Tibetan Plateau (ITP), a transition zone with shifting influences between the westerlies and the Indian summer monsoon. In the present study, glacier area and mass changes were determined by topographic maps (TOPO), Landsat imagery and multi-temporal digital elevation models (DEMs) generated with TOPO, SRTM, TanDEM-X bistatic interferometric synthetic aperture radar (InSAR) images, and High Mountain Asia 8-m DEMs. On average, the glaciers showed a slight retreat from 343.27 ± 5.23 km2 in 1971 to 334.67 ± 3.21 km2 in 2018 (0.05 ± 0.04% a−1). However, glaciers lost mass at a rate of -0.32 ± 0.03 m w.e. a−1 from 1971 to 2012. For the 1999–2012 and 2012–2017 periods, mass balances of − 0.03 ± 0.16 and 0.09 ± 0.04 m w.e. a−1, respectively, were observed, which represents an approximately equilibrium. Two glaciers also advanced in our investigation period, and we confirmed one of them surged in 2015.

Accelerated glacier mass loss (2011–2016) over the Puruogangri ice field in the inner Tibetan Plateau revealed by bistatic InSAR measurements

The temporal variation of glacier mass balance during recent years remains poorly known for the mountain glaciers in the inner Tibetan Plateau (ITP), due to the lack of field measurements. In this study, we retrieved the annual glacier mass balance of the Puruogangri ice field, which is the largest modern ice mass in the ITP, by differencing multi-temporal digital elevation models (DEMs) generated with five pairs of TanDEM-X bistatic interferometric synthetic aperture radar (InSAR) images acquired between April 2011 and January 2016. We compared the TanDEM-X DEMs in January and April 2012 to estimate the X-band radar penetration depth difference (0.61 ± 0.06 m), which enabled systematic bias correction in the estimation of annual glacier mass balance. The observed mass balance reveals a glacier mass gain of 0.44 ± 0.10 m w.e. yr−1 in 2011–12, which was followed by accelerated glacier mass loss in 2012–16. Glacier mass balances of −0.13 ± 0.03, −0.34 ± 0.06, and − 0.52 ± 0.10 m w.e. yr−1 were estimated for the periods of 2012–13, 2013–14, and 2014–16, respectively. This accelerating trend of glacier mass loss is likely caused by the continuous decrease in annual precipitation, according to the climate data recorded by adjacent meteorological stations. This study demonstrates that repeated bistatic InSAR measurement is a promising method for monitoring glacier elevation change and mass balance at regular intervals.

Refined Two-Stage Programming Approach of Phase Unwrapping for Multi-Baseline SAR Interferograms Using the Unscented Kalman Filter

Phase unwrapping (PU) represents a key step in the reconstruction of digital elevation models (DEMs) and the monitoring of surface deformation from interferometric synthetic aperture radar (InSAR) data. Compared with single-baseline (SB) PU, multi-baseline (MB) PU can resolve the phase discontinuities caused by noise and phase layover induced by terrain undulations. However, the MB PU performance is limited primarily by its poor robustness to measurement bias and noise. To address this problem, we propose a refined 2-D MB PU method based on the two-stage programming approach (TSPA). The proposed method uses the unscented Kalman filter (UKF) to improve the performance of the second stage of the original TSPA method. Specifically, the proposed method maintains the first stage of the TSPA to estimate the range and azimuth gradients between neighbouring pixels. Then, median filtering is slightly used to reduce the effects of the noise gradients on the estimated phase gradients. Finally, the UKF model is used to unwrap the interferometric phases using an efficient quality-guided strategy based on heap-sort. This paper is the first to integrate the UKF into the TSPA framework. The proposed method is validated using bistatic and monostatic MB InSAR datasets, and the experimental results show that the proposed method is effective for MB PU problems.

Flood Mapping in a Complex Environment Using Bistatic TanDEM-X/TerraSAR-X InSAR Coherence

In this paper, we assess the flood mapping capabilities of the X-band Synthetic Aperture Radar (SAR) imagery acquired by the bistatic pair TanDEM-X/TerraSAR-X (TDX/TSX). The main objective is to investigate the added value of the bistatic TDX/TSX Interferometric Synthetic Aperture Radar (InSAR) coherence in addition to the SAR backscatter in the context of inundation mapping. As a classifier, we consider a Random Forest (RF) classification scheme using TDX/TSX SAR intensities and their bistatic InSAR coherence to extract the flood extent map. To evaluate the classification results and as no “ground truth” was available at the SAR data acquisition time, we set up a LISFLOOD-FP hydraulic model for simulating the temporal evolution of the flood water. The flood map simulated by the model shows good performances with an Overall Accuracy (OA) of 97.92 % and a Critical Success Index (CSI) of 94 . 01 % . The SAR-derived flood map is then compared to the LISFLOOD-FP extent map simulated at the SAR data acquisition time. As a test case, we consider the flooding event of the Richelieu River that occurred in the Montérégie region of Quebec (Canada) from April to June 2011. Experimental results highlight the potential of the bistatic InSAR coherence for more accurate flood mapping in a complex landscape with urban and vegetation areas. The classification results of the SAR-derived flood map with respect to the LISFLOOD-FP flood map reach an OA of 78.65 % and a Precision of 82.08 % when integrating the bistatic InSAR coherence. These classification OA and Precision values are 69.63 % and 64.52 % , respectively, using only the TDX/TSX SAR intensity.

Mapping Glacier Elevations and Their Changes in the Western Qilian Mountains, Northern Tibetan Plateau, by Bistatic InSAR

Accurate measurements of glacier surface topography and their changes play an essential role in various glaciological studies related to glacier dynamics and mass balance. The focus of this study is on mapping glacier digital elevation model (DEM) and elevation changes in the western Qilian Mountains, northern Tibetan Plateau, by synergistically using the TanDEM-X (TDX) bistatic Interferometric Synthetic Aperture Radar (InSAR) data in 2013 and Shuttle Radar Topography Mission (SRTM) DEM in 2000. The first high-resolution and high-precision glacier DEM is derived in this region by a TDX InSAR procedure with a nonlocal (NL) filter. Validated against the Ice, Cloud, and land Elevation Satellite (ICESat) height references, the absolute height error of the TanDEM-X DEM derived with the NL filter and the Goldstein filter with the parameters investigated is, respectively, 1.493 ± 0.747 and 1.857 ± 1.709 m. Further, four combinations of differential phase method (DiffPha) and DEM differencing method (DiffDem) with Goldstein filter and NL filter are applied to estimate glacier elevation changes between 2000 and 2013. The synergistic use of the DiffPha method and the NL filter is superior to other three combinations in terms of uncertainty and noise reduction. Generally, a clear surface thinning can be found in most glacier tongue regions, the maximum value of elevation lowering up to approximately −40 m, whereas a slight thickening is detected in accumulation areas, which are in agreement with the height difference results between GPS measurements and SRTM DEM over Laohugou Glacier No.12. This study demonstrates the potential of the TanDEM-X bistatic InSAR in mapping surface topography and elevation changes of valley glaciers in the Tibetan Plateau.

Rapid raw data simulation for fixed-receiver bistatic interferometric synthetic aperture radar

Raw data simulation of synthetic aperture radar (SAR) is useful for system designing, mission planning, and testing of imaging algorithms. According to the two-dimensional (2-D) frequency spectrum of the fixed-receiver bistatic SAR system, a rapid raw data simulation approach is proposed. With the combination of 2-D inverse Stolt transform in the 2-D frequency domain and phase compensation in the range-Doppler frequency domain, our approach can significantly reduce the simulation time. Therefore, simulations of extended scenes can be performed much more easily. Moreover, the proposed algorithm offers high accuracy of phase distribution, therefore, it can be used for single-pass fixed-receiver bistatic interferometric usage. The proposal is verified by extensive simulations of point targets and extended scene, in which the results indicate the feasibility as well as the effectiveness of our approach. In the end, the accuracy of phase distribution of the proposed algorithm is further examined with simulations of synthetic aperture radar interferometry.

Two years of TanDEM-X baseline determination

The TanDEM-X mission is a German dual satellite formation with the task to acquire a global digital elevation model (DEM) by bistatic interferometric synthetic aperture radar (SAR) data takes. In order to reach the intended DEM accuracy, the two satellites are kept in formation with a distance of less than 500 m and the baseline vector between the two spacecraft needs to be determined with an accuracy of 1 mm. The baseline determination uses observations from the onboard GPS receivers. The baseline vector between the satellites is determined by three independent software packages as there is no independent instrument onboard to verify the GPS results. In studies prior to the mission, comparisons between independent software packages showed biases of a few millimetres. In order to ensure the highest accuracy, a baseline calibration and combination process has been installed. The baseline products are validated by dedicated baseline calibration data takes over test sites, where the DEM is well known. Finally, the different solutions are merged in order to further reduce the errors.

TanDEM-X Mission: Overview and Evaluation of intermediate Results

Abstract. The German Aerospace Center (DLR, Deutsches Zentrum für Luft- und Raumfahrt) currently conducts the bistatic interferometric synthetic aperture radar (SAR) Mission TanDEM-X, which shall result in a DEM of global coverage in an unprecedented resolution and accuracy according to DTED level 3 standard. The mission is based on the two SAR satellites TerraSAR-X and TanDEM-X that have been launched in June 2007 and 2010, respectively. After the commissioning phase of TanDEM satellite and the orbital adjustment the bistatic image acquisition in close formation began end of 2010. The data collection for the mission is scheduled to last about three years, i.e., the bigger part of the required data have been already gathered. Based on this data DLR will conduct several processing steps in order to come up finally with a global and seamless DEM of the Earth's landmass which shall meet the envisaged specifications. Since the entire mission is an endeavor in the framework of a private-public-partnership, the private partner, Astrium, will eventually commercialize the DEM product. In this paper, we will provide an overview of the data collection and the deliverables that will come along with TanDEM-X mission. Furthermore, we will analyze a DEM derived from early stage immediate products of the mission.

Three-dimensional surface reconstruction from multistatic SAR images

This paper discusses reconstruction of three-dimensional surfaces from multiple bistatic synthetic aperture radar (SAR) images. Techniques for surface reconstruction from multiple monostatic SAR images already exist, including interferometric processing and stereo SAR. We generalize these methods to obtain algorithms for bistatic interferometric SAR and bistatic stereo SAR. We also propose a framework for predicting the performance of our multistatic stereo SAR algorithm, and, from this framework, we suggest a metric for use in planning strategic deployment of multistatic assets.