Biofilm Mechanical Properties Research Articles

Modified magnesium oxide/silver nanoparticles reinforced poly (butylene succinate-co-terephthalate) composite biofilms for food packaging application

MgO/Ag nanoparticles (NPs) were surface-modified with titanate coupling agent titaniumtriisostearoylisopropoxide (NDZ-130). A new antibacterial biofilm for food packaging was synthesized by combining the modified MgO/Ag NPs with poly (butylene succinate-co-terephthalate) (PBST). The modification improved the compatibility between the MgO/Ag NPs and the PBST matrix. The effects of the modified MgO/Ag NPs on biofilm mechanical, barrier, thermal, antibacterial and food preservation properties were evaluated. Compared with the PBST/MgO/Ag composite film, the modified PBST/MgO/Ag composite film showed an increase in tensile strength (TS) of 8.71% and elongation at break (EB) of 16.66%, additionally decreasing water vapor permeability (WVP) by 42.86%. The composite film also exhibited over 95% inhibition of Staphylococcus aureus and Escherichia coli. The modified PBST/MgO/Ag composite film avoided microbial contamination and preserved cherry tomatoes while maintaining moisture and firmness for six days. All results indicated that the prepared biofilms have a high potential for use as food packaging films.

The impact of potassium peroxymonosulphate and chlorinated cyanurates on biofilms of Stenotrophomonas maltophilia: effects on biofilm control, regrowth, and mechanical properties

The activity of two chlorinated isocyanurates (NaDCC and TCCA) and peroxymonosulphate (OXONE) was evaluated against biofilms of Stenotrophomonas maltophilia, an emerging pathogen isolated from drinking water (DW), and for the prevention of biofilm regrowth. After disinfection of pre-formed 48 h-old biofilms, the culturability was reduced up to 7 log, with OXONE, TCCA, and NaDCC showing more efficiency than free chlorine against biofilms formed on stainless steel. The regrowth of biofilms previously exposed to OXONE was reduced by 5 and 4 log CFU cm−2 in comparison to the unexposed biofilms and biofilms exposed to free chlorine, respectively. Rheometry analysis showed that biofilms presented properties of viscoelastic solid materials, regardless of the treatment. OXONE reduced the cohesiveness of the biofilm, given the significant decrease in the complex shear modulus (G*). AFM analysis revealed that biofilms had a fractured appearance and smaller bacterial aggregates dispersed throughout the surface after OXONE exposure than the control sample. In general, OXONE has been demonstrated to be a promising disinfectant to control DW biofilms, with a higher activity than chlorine. The results also show the impact of the biofilm mechanical properties on the efficacy of the disinfectants in biofilm control.

The effect of intraoperative immersion solutions on acellular dermal matrix: Biofilm formation and mechanical property

Acellular dermal matrix (ADM) is generally used on implant-based breast operations; However, it can increase surgical site infection. Many immersion solutions are applied to ADM, however, the most effective solution is unknown. The purpose of this study is to determine the effect of different solutions on the biofilm formation and mechanical properties of ADM. Aseptic porcine-derived ADMs were immersed in 5 different solutions for 30min; sterile normal saline, 10% povidone-iodine, 0.5% chlorhexidine, antibiotics (cefazolin, gentamicin, and vancomycin), and taurolidine. They are transferred to 10ml suspension of methicillin-sensitive/resistant Staphylococcus aureus (MSSA/MRSA) or Staphylococcus epidermidis and an overnight culture was performed. After rinsing and sonication to obtain the biofilm on ADM, colony forming unit (CFU) was measured. In addition, the maximum load before ADM deformation and the elongation length of ADM at the start of the maximum load was determined. Regardless of strains, povidone-iodine, chlorhexidine, and taurolidine group had lower CFUs than the saline group with statistical significance. Meanwhile, the antibiotics group did not show statistical difference from the saline group. Moreover, only taurolidine group showed higher tensile strength (MRSA, p=0.0003; S. epidermidis, p=0.0023) and elongation length (MSSA, p=0.0015) than the saline group. The antibiotics and chlorhexidine group yielded lower tensile strength and elongation length than the povidone-iodine and taurolidine groups. It was suggested that the 10% povidone-iodine or taurolidine solution is effective. In contrast, the antibiotics solution could be considered as an effective intraoperative solution.

In Vitro Models of Bacterial Biofilms: Innovative Tools to Improve Understanding and Treatment of Infections

Bacterial infections are a growing concern to the health care systems. Bacteria in the human body are often found embedded in a dense 3D structure, the biofilm, which makes their eradication even more challenging. Indeed, bacteria in biofilm are protected from external hazards and are more prone to develop antibiotic resistance. Moreover, biofilms are highly heterogeneous, with properties dependent on the bacteria species, the anatomic localization, and the nutrient/flow conditions. Therefore, antibiotic screening and testing would strongly benefit from reliable in vitro models of bacterial biofilms. This review article summarizes the main features of biofilms, with particular focus on parameters affecting biofilm composition and mechanical properties. Moreover, a thorough overview of the in vitro biofilm models recently developed is presented, focusing on both traditional and advanced approaches. Static, dynamic, and microcosm models are described, and their main features, advantages, and disadvantages are compared and discussed.

Zein/hydroxypropylcellulose biofilms with hydrophilic and hydrophobic montmorillonite clays

AbstractThis study analyzed the changes in the structural, morphological and mechanical properties of Biofilm A (46.1% zein/30.8% hydroxypropylcellulose/23.1% propylene glycol) and Biofilm B (53.8% zein/23.1% hydroxypropylcellulose/23.1% propylene glycol) when 0.5%, 1% or 2% Cloisite Na+ (NaMt) and 1% Cloisite 30B (C30B) were added to the systems. Infrared spectroscopy showed clay particles interact with the polymeric matrix mainly via hydrogen bonds between silanol and amide/hydroxyl groups from minerals and polymers, respectively. X‐ray diffraction and small angle X‐ray scattering patterns indicated clays were exfoliated in both formulations with 0.5% NaMT and 1% C30B, or presented larger lamellar spacing on biofilms containing 1% or 2% of hydrophilic clay compared to pure clays. Scanning electron micrographs showed clay were incorporated into the polymers at low clay content and presented some aggregates at 2% NaMt. Mechanical tests showed that Biofilms B had better mechanical properties compared to Biofilms A, and Biofilms B with 1% NaMt presented the highest value of tensile strength. Moreover, the addition of organophilic clay in both formulations produced nanocomposites with good mechanical properties. These results showed clays are strategic to obtain nanocomposite films with interesting physical and chemical properties.

Influence of Metal Cations on the Viscoelastic Properties of Escherichia coli Biofilms.

Biofilms frequently cause complications in various areas of human life, e.g., in medicine and in the food industry. More recently, biofilms are discussed as new types of living materials with tunable mechanical properties. In particular, Escherichia coli produces a matrix composed of amyloid-forming curli and phosphoethanolamine-modified cellulose fibers in response to suboptimal environmental conditions. It is currently unknown how the interaction between these fibers contributes to the overall mechanical properties of the formed biofilms and if extrinsic control parameters can be utilized to manipulate these properties. Using shear rheology, we show that biofilms formed by the E. coli K-12 strain AR3110 stiffen by a factor of 2 when exposed to the trivalent metal cations Al(III) and Fe(III), while no such response is observed for the bivalent cations Zn(II) and Ca(II). Strains producing only one matrix component did not show any stiffening response to either cation or even a small softening. No stiffening response was further observed when strains producing only one type of fiber were co-cultured or simply mixed after biofilm growth. These results suggest that the E. coli biofilm matrix is a uniquely structured composite material when both matrix fibers are produced from the same bacterium. While the exact interaction mechanism between curli, phosphoethanolamine-modified cellulose, and trivalent metal cations is currently not known, our results highlight the potential of using extrinsic parameters to understand and control the interplay between biofilm structure and mechanical properties. This will ultimately aid in the development of better strategies for controlling biofilm growth.

Impact of Fe2+ and Shear Stress on the Development and Mesoscopic Structure of Biofilms-A Bacillus subtilis Case Study.

Bivalent cations are known to affect the structural and mechanical properties of biofilms. In order to reveal the impact of Fe2+ ions within the cultivation medium on biofilm development, structure and stability, Bacillus subtilis biofilms were cultivated in mini-fluidic flow cells. Two different Fe2+ inflow concentrations (0.25 and 2.5 mg/L, respectively) and wall shear stress levels (0.05 and 0.27 Pa, respectively) were tested. Mesoscopic biofilm structure was determined daily in situ and non-invasively by means of optical coherence tomography. A set of ten structural parameters was used to quantify biofilm structure, its development and change. The study focused on characterizing biofilm structure and development at the mesoscale (mm-range). Therefore, biofilm replicates (n = 10) were cultivated and analyzed. Three hypotheses were defined in order to estimate the effect of Fe2+ inflow concentration and/or wall shear stress on biofilm development and structure, respectively. It was not the intention to investigate and describe the underlying mechanisms of iron incorporation as this would require a different set of tools applied at microscopic levels as well as the use of, i.e., omic approaches. Fe2+ addition influenced biofilm development (e.g., biofilm accumulation) and structure markedly. Experiments revealed the accumulation of FeO(OH) within the biofilm matrix and a positive correlation of Fe2+ inflow concentration and biofilm accumulation. In more detail, independent of the wall shear stress applied during cultivation, biofilms grew approximately four times thicker at 2.5 mg Fe2+/L (44.8 µmol/L; high inflow concentration) compared to the low Fe2+ inflow concentration of 0.25 mg Fe2+/L (4.48 µmol/L). This finding was statistically verified (Scheirer-Ray-Hare test, ANOVA) and hints at a higher stability of Bacillus subtilis biofilms (e.g., elevated cohesive and adhesive strength) when grown at elevated Fe2+ inflow concentrations.

Elastomeric sandpaper replicas as model systems for investigating elasticity, roughness and associated drag in a marine biofilm flow cell

Biofilm heterogeneity and adaptability complicates efforts to link biofilm structural and mechanical properties to frictional drag. As a result, rigid structures are typically used as the benchmark for studying biofilm-associated drag. Elastomeric sandpaper replicas were generated to be used as model systems for investigating the effect of roughness and elasticity on drag, over the Reynolds number range of approximately 2.0 × 104 to 5.2 × 104 Re using a marine biofilm flow cell. To control for roughness parameters and surface topography the replicas were created for sandpaper grit numbers: P40, P80 and P240 with average measured roughness (Sa) of 108, 49 and 16 μm, respectively. Profilometry confirmed that there was no significant difference between the roughness of the rigid sandpaper sources and the material replicas. The marine biofilm flow cell was fitted with a clear lid, which allowed real-time visualisation of the replicas’ surface topography using Optical Coherence Tomography. Pressure drop measurements, expressed as a friction coefficient, revealed that the elastomeric sandpaper replicas had a significantly higher associated drag, of up to 52%, when compared to the rigid counterparts. From statistical analysis it was confirmed that material mechanical properties, such as elasticity, and surface roughness both significantly affect drag. Elastic model systems can be used to enhance our understanding of biofilm physico-mechanics and their role in marine drag.

Effects of Mucin and DNA Concentrations in Airway Mucus on Pseudomonas aeruginosa Biofilm Recalcitrance.

ABSTRACTThe pathological properties of airway mucus in cystic fibrosis (CF) are dictated by mucus concentration and composition, with mucins and DNA being responsible for mucus viscoelastic properties. As CF pulmonary disease progresses, the concentrations of mucins and DNA increase and are associated with increased mucus viscoelasticity and decreased transport. Similarly, the biophysical properties of bacterial biofilms are heavily influenced by the composition of their extracellular polymeric substances (EPS). While the roles of polymer concentration and composition in mucus and biofilm mechanical properties have been evaluated independently, the relationship between mucus concentration and composition and the biophysical properties of biofilms grown therein remains unknown. Pseudomonas aeruginosa biofilms were grown in airway mucus as a function of overall concentration and DNA concentration to mimic healthy, and CF pathophysiology and biophysical properties were evaluated with macro- and microrheology. Biofilms were also characterized after exposure to DNase or DTT to examine the effects of DNA and mucin degradation, respectively. Identifying critical targets in biofilms for disrupting mechanical stability in highly concentrated mucus may lead to the development of efficacious biofilm therapies and ultimately improve CF patient outcomes. Overall mucus concentration was the predominant contributor to biofilm viscoelasticity and both DNA degradation and mucin reduction resulted in compromised biofilm mechanical strength.IMPORTANCE Pathological mucus in cystic fibrosis (CF) is highly concentrated and insufficiently cleared from the airway, causing chronic inflammation and infection. Pseudomonas aeruginosa establishes chronic infection in the form of biofilms within mucus, and this study determined that biofilms formed in more concentrated mucus were more robust and less susceptible to mechanical and chemical challenges compared to biofilms grown in lower concentrated mucus. Neither DNA degradation nor disulfide bond reduction was sufficient to fully degrade biofilms. Mucus rehydration should remain a priority for treating CF pulmonary disease with concomitant multimechanistic biofilm degradation agents and antibiotics to clear chronic infection.

Probing the growth and mechanical properties of Bacillus subtilis biofilms through genetic mutation strategies

Bacterial communities form biofilms on various surfaces by synthesizing a cohesive and protective extracellular matrix, and these biofilms protect microorganisms against harsh environmental conditions. Bacillus subtilis is a widely used experimental species, and its biofilms are used as representative models of beneficial biofilms. Specifically, B. subtilis biofilms are known to be rich in extracellular polymeric substances (EPS) and other biopolymers such as DNA and proteins like the amyloid protein TasA and the hydrophobic protein BslA. These materials, which form an interconnected, cohesive, three-dimensional polymer network, provide the mechanical stability of biofilms and mediate their adherence to surfaces among other functional contributions. Here, we explored how genetically-encoded components specifically contribute to regulate the growth status, mechanical properties, and antibiotic resistance of B. subtilis biofilms, thereby establishing a solid empirical basis for understanding how various genetic engineering efforts are likely to affect the structure and function of biofilms. We noted discrete contributions to biofilm morphology, mechanical properties, and survival from major biofilm components such as EPS, TasA and BslA. For example, EPS plays an important role in maintaining the stability of the mechanical properties and the antibiotic resistance of biofilms, whereas BslA has a significant impact on the resolution that can be obtained for printing applications. This work provides a deeper understanding of the internal interactions of biofilm components through systematic genetic manipulations. It thus not only broadens the application prospects of beneficial biofilms, but also serves as the basis of future strategies for targeting and effectively removing harmful biofilms.

Fabrication and characterization of biopolymers with antibacterial nanoparticles and Calendula officinalis flower extract as an active ingredient for modern hydrogel wound dressings

Hydrogels are three-dimensional networks that can absorb moisture up to several times their weight and have many medical and biological applications. In this paper, the fabrication and characterization of a three-component chitosan (CS) / sodium alginate (SA) / polyvinyl alcohol (PVA) hydrogel with various weight percentages (0, 5, 10, 15, and 20) wt% of Ag2O/SiO2 with Calendula officinalis flower extract as an active ingredient are fabricated as a novel and green wound dressing. After forming bio-nano composites utilizing the cross-linking technique, Fourier transform infrared (FT-IR) spectroscopy is applied to determine and prove the functional groups added to the CS/PVA/SA at the whole step. X-ray diffraction (XRD) analysis is performed to prove the crystalline and amorphous structure of Ag2O/SiO2 NPs. The field emission scanning electron microscope (FE-SEM) analyses and Energy-dispersive X-ray spectroscopy (EDS) are performed to confirm the morphology of the composition and check the elements to increase wound healing. Atomic force microscope (AFM) examination is done to prove and determine surface roughness and pores. The tensile test is performed to determine the tensile strength and mechanical properties of nanocomposites. Also, by immersing nanocomposites in the simulated body fluid (SBF) and phosphate buffer salt (PBS), the swelling ratio is determined, and the release of Calendula officinalis flower extract is measured in PBS. Finally, the synthesized hydrogel's water vapor transmission rate (WVRT) and then antibacterial tests are determined. This research proves that with the increase of Ag2O/SiO2 NPs to 20% wt., the biofilm's tensile strength and mechanical properties and all healing properties have improved significantly. Producing these films is very effective in improving skin infections. Finally, the thermogravimetric analysis (TGA) is applied to estimate the thermal stability of the biopolymer films with various percentages of mesoporous Ag2O/SiO2 nanoparticles.

Effects of eukaryotic predation on nitrifying MABR biofilms

This research explored the effects of eukaryotic predation on nitrifying membrane-aerated biofilm reactor (MABR) biofilms. Past research on heterotrophic MABR biofilms showed that predation could create internal voids that promoted sloughing. However, the no past research addressed the effects of predation on nitrifying MABRs, even though nitrification is the most common MABR application. Nitrifying biofilms are typically denser, and ammonia oxidizing bacteria (AOB) form large, dense clusters within the biofilm. This could affect their susceptibility to predation. Nitrifying biofilms were grown in flat-sheet MABRs. Images of the biofilm were captured using optical coherence tomography (OCT). For detachment tests, an increased shear flow (Re≅140) was used, and a shear rheometer was used to measure the biofilm mechanical properties. The nitrifying community was analyzed with fluorescence in situ hybridization (FISH) and quantitative PCR (qPCR). Predation increased internal void ratios from 54 ± 5% to 69 ± 6%. Biofilms were weakened by predation, with a storage modulus (G′) and loss modulus (G′′) of 242 ± 135 and 1,649 ± 853 Pa with predation and 3,644 ± 1,857 and 23,334 ± 11,481 Pa for the control with suppressed predation. Predation increased the relative biofilm detachment from 4 ± 5 to 18 ± 12%, decreased the amount of biomass, i.e., the average biofilm thickness, from 502 ± 150 to 266 ± 54 µm, and decreased the nitrification flux from 1.00 to 0.61 g NH4+-N/m2day. Also, predation decreased the abundance of nitrite oxidizing bacteria (NOB) relative to AOB, consistent with the observed nitritation. These results show that predation can significantly impact the structural stability, bacterial community and removal rates of nitrifying MABR biofilms. Lumping the effects of predation into the detachment or decay coefficients of biofilm models may not accurately reflect the behavior of nitrifying MABR biofilms.

Dependency of hydration and growth conditions on the mechanical properties of oral biofilms

Within the oral cavity, dental biofilms experience dynamic environments, in part due to changes in dietary content, frequency of intake and health conditions. This can impact bacterial diversity and morpho-mechanical properties. While phenotypic properties of oral biofilms are closely related to their composition, these can readily change according to dynamic variations in the growth environment and nutrient availability. Understanding the interlink between phenotypic properties, variable growth conditions, and community characterization is an essential requirement to develop structure–property relationships in oral-biofilms. In this study, the impact of two distinct growth media types with increasing richness on the properties of oral biofilms was assessed through a new combination of in-vitro time-lapse biophysical methods with microbiological assays. Oral biofilms grown in the enriched media composition presented a decrease in their pH, an increase in soluble EPS production, and a severe reduction in bacterial diversity. Additionally, enriched media conditions presented an increase in biofilm volumetric changes (upon hydration) as well as a reduction in elastic modulus upon indentation. With hydration time considered a major factor contributing to changes in biofilm mechanical properties, we have shown that it is less associated than media richness. Future investigations can now use this time-lapse approach, with a clearer focus on the extracellular matrix of oral biofilms dictating their morpho-mechanical properties.

The Comparison of Biofilm Formation, Mechanical and Chemical Properties between Glass Ionomer Cement and Giomer

Aims: The aim of this study was to compare compressive strength and its correlation with the surface morphology and chemical elements of GIC and Giomer, as well as to determine the fluoride amount effect on the bacterial biofilm formation of GIC and Giomer. Background: The liability of Glass Ionomer Cement (GIC) mechanical properties is overcome with better antibacterial properties among restorative materials. Another fluoride-releasing restorative material, such as Giomer, has been discovered and is expected to overcome the issues with GIC’s mechanical properties; however, no research has been conducted related to antibacterial properties in Giomer. Objective: To compare compressive strength and its correlation with the surface morphology and chemical elements, then determine the fluoride amount effect on the bacterial biofilm formation of GIC and Giomer. Methods: Sixteen specimens of GIC and Giomer were prepared for a compressive strength measurement with the Universal Testing Machine. Sixteen specimens of GIC and Giomer were incubated for three days with the Streptococcus mutans culture at 37°C. The bacterial colonization was calculated using the Colony Forming Unit (CFU) and bacterial adhesion was calculated using a Scanning Electron Microscope (SEM). The mechanical properties’ compressive strength measurement, surface morphology, and chemical elements analyses were performed using SEM-EDX. Results: The compressive strength of Giomer was higher than GIC (P=0.001). The higher compressive strength of Giomer was reflected by a predominant regular surface, fewer voids, smaller and denser particles, and a higher content of silica and carbon. The bacterial biofilm on the surface of Giomer was higher than GIC, although there was no significant difference. GIC and Giomer have identical chemical elements: C, O, F, Na, Al, Si, P, and Ca. Conclusion: The compressive strength of Giomer is better than GIC; however, the biofilm formation of Giomer is higher than GIC, whereas GIC has a higher fluoride content but inferior in surfaces morphology characteristic

Influence of Rhamnolipids and Ionic Cross-Linking Conditions on the Mechanical Properties of Alginate Hydrogels as a Model Bacterial Biofilm.

The literature indicates the existence of a relationship between rhamnolipids and bacterial biofilm, as well as the ability of selected bacteria to produce rhamnolipids and alginate. However, the influence of biosurfactant molecules on the mechanical properties of biofilms are still not fully understood. The aim of this research is to determine the effect of rhamnolipids concentration, CaCl2 concentration, and ionic cross-linking time on the mechanical properties of alginate hydrogels using a Box–Behnken design. The mechanical properties of cross-linked alginate hydrogels were characterized using a universal testing machine. It was assumed that the addition of rhamnolipids mainly affects the compression load, and the value of this parameter is lower for hydrogels produced with biosurfactant concentration below CMC than for hydrogels obtained in pure water. In contrast, the addition of rhamnolipids in an amount exceeding CMC causes an increase in compression load. In bacterial biofilms, the presence of rhamnolipid molecules does not exceed the CMC value, which may confirm the influence of this biosurfactant on the formation of the biofilm structure. Moreover, rhamnolipids interact with the hydrophobic part of the alginate copolymer chains, and then the hydrophilic groups of adsorbed biosurfactant molecules create additional calcium ion trapping sites.

Optimization of The Addition Of Polivinil Alcohol (PVA) as A Plasticizer In Biofilm with Tapioca-Chitosan Flour Material

The addition of a plasticizer, namely polyvinyl alcohol (PVA) as a plasticizer, will increase flexibility and prevent the polymer from cracking. The purpose of this study was to compare the mechanical properties of biofilms from tapioca-chitosan flour with or without the addition of polyvinyl alcohol (PVA) and determine the mass of polyvinyl alcohol (PVA) which can provide optimum mechanical properties of biofilms, test the biodegradability of biofilms and polypropylene plastics and to analyze biofilms using FT-IR. The making of biofilm from 4% tapioca flour and 2% chitosan was carried out by adding variations of polyvinyl alcohol as much as 0, 1, 2, 3, 4 and 5 grams to each tapioca-chitosan flour solution. The effect of adding polyvinyl alcohol (PVA) can be seen from the results of the tensile strength test, the breaking length test, the water resistance test and the biodegradability test. The resulting biofilm functional group analysis was performed by FT-IR. The results showed that the addition of PVA could increase the tensile strength and breaking length, but decreased the water resistance of the biofilm. The optimum mechanical properties of tapioca-chitosan flour biofilm resulted from the addition of 3 grams of PVA with a tensile strength of 2.163 kgf / cm2, the breaking length of 13.64% and 12.46% of absorbed water. Biofilms can be degraded by the fungus Aspergilus niger. The results of biofilm analysis using FTIR indicate the presence of functional groups (CH, NH2, NH, OH, CO and CN) which are the functional groups of the biofilm constituent materials. The optimum mechanical properties of tapioca-chitosan flour biofilm resulted from the addition of 3 grams of PVA with a tensile strength of 2.163 kgf / cm2, the breaking length of 13.64% and 12.46% of absorbed water. Biofilms can be degraded by the fungus Aspergilus niger. The results of biofilm analysis using FT-IR indicate the presence of functional groups (CH, NH2, NH, OH, CO and CN) which are the functional groups of the biofilm constituent materials.

Spatial distribution of mechanical properties in Pseudomonas aeruginosa biofilms, and their potential impacts on biofilm deformation.

The mechanical properties of biofilms can be used to predict biofilm deformation under external forces, for example, under fluid flow. We used magnetic tweezers to spatially map the compliance of Pseudomonas aeruginosa biofilms at the microscale, then applied modeling to assess its effects on biofilm deformation. Biofilms were grown in capillary flow cells with Reynolds numbers (Re) ranging from 0.28 to 13.9, bulk dissolved oxygen (DO) concentrations from 1 mg/L to 8 mg/L, and bulk calcium ion (Ca2+ ) concentrations of 0 and 100 mg CaCl2 /L. Higher Re numbers resulted in more uniform biofilm morphologies. The biofilm was stiffer at the center of the flow cell than near the walls. Lower bulk DO led to more stratified biofilms. Higher Ca2+ concentrations led to increased stiffness and more uniform mechanical properties. Using the experimental mechanical properties, fluid-structure interaction models predicted up to 64% greater deformation for heterogeneous biofilms, compared with a homogeneous biofilms with the same average properties. However, the deviation depended on the biofilm morphology and flow regime. Our results show significant spatial mechanical variability exists at the microscale, and that this variability can potentially affect biofilm deformation. The average biofilm mechanical properties, provided in many studies, should be used with caution when predicting biofilm deformation.

Low-shrinkage-stress nanocomposite: An insight into shrinkage stress, antibacterial, and ion release properties.

The aims are: (a) To develop the first low-shrinkage-stress nanocomposite with antibacterial and remineralization capabilities through the incorporation of dimethylaminododecyl methacrylate (DMAHDM) and nanoparticles of amorphous calcium phosphate (NACP); (b) to investigate the effects of the new composite on biofilm inhibition, mechanical properties, shrinkage stress, and calcium (Ca) and phosphate (P) ion releases. The low-shrinkage-stress resin consisted of urethane dimethacrylate and triethylene glycol divinylbenzyl ether. Composite was formulated with 3% DMAHDM and 20% NACP. Mechanical properties, shrinkage stress, and degree of conversion were evaluated. Streptococcus mutans biofilm growth on composites was assessed. Ca and P ion releases were measured. The shrinkage stress of the low-shrinkage-stress composite containing 3% DMAHDM and 20% NACP was 36% lower than that of traditional composite control (p < 0.05), with similar degrees of conversion of 73.9%. The new composite decreased the biofilm colony-forming unit by 4 log orders and substantially reduced biofilm lactic acid production compared to control composite (p < 0.05). Incorporating DMAHDM to the low-shrinkage-stress composite did not adversely affect the Ca and P ion release. A novel bioactive nanocomposite was developed with low shrinkage stress, strong antibiofilm activity, and high levels of ion release for remineralization, without undermining the mechanical properties and degree of conversion.

Transient in situ measurement of kombucha biofilm growth and mechanical properties.

Kombucha is a traditional beverage obtained by the fermentation of sugared tea by a symbiotic culture of bacteria and yeast which has recently re-emerged as a popular lifestyle product with potential health benefits. The characteristic feature of kombucha is the formation of a cellulosic biofilm due to the excretion of bacterial cellulose with high purity and crystallinity. Despite the growing industrial and technological interest in kombucha, current characterization techniques rely on the periodic sampling of tea broth or biofilm and ex situ analysis of its biochemical or microbial composition. Here, we use interfacial shear rheology (ISR) for the transient in situ determination of kombucha biofilm growth directly at the interface. ISR revealed that kombucha biofilm formation is a two step process with clearly distinguishable growth phases. The first phase can be attributed to the initial adsorption of bacteria at the air-water interface and shows great variability, probably due to varying bacteria content and composition. The second phase is initiated by bacterial cellulose excretion and shows astonishing reproducibility regarding onset and final mechanical properties. Hence, ISR qualifies as a new in situ characterization technique for kombucha biofilm growth and bacterial cellulose production.

Effect of Nonphosphorus Corrosion Inhibitors on Biofilm Pore Structure and Mechanical Properties.

Understanding the effects of biofilm structural and mechanical properties, which can influence biofilm cohesiveness and detachment under physical stress, is critical for biofilm and biofilm-associated pathogen control. In this study, we used optical coherence tomography (OCT) and nanoindentation to determine the role of silicate and tin (two experimental nonphosphate corrosion inhibitors) on the porous structure and stiffness of three types of multispecies biofilms. These biofilms were grown from groundwater (a drinking water source), and this groundwater was amended with either tin or silicate corrosion inhibitor (0.5 mg/L as Sn and 20 mg/L as SiO2). Based on the elastic moduli of these biofilms, tin biofilms and groundwater biofilms were the stiffest, followed by silicate biofilms. The thickness normalized by the growth time for silicate biofilms was highest at 38 ± 7.1 μm/month, compared to 21 ± 3.2 and 11 ± 2.4 μm/month for tin biofilms and groundwater biofilms, respectively. The silicate biofilms had the greatest overall porosities and were thickest among the three biofilms. Based on the pore network modeling (PNM) of OCT images, larger pores and connections were found in the silicate biofilms compared to those in tin and groundwater biofilms. Our analysis showed that the thicker and more porous biofilms (silicate biofilms) were potentially less resistant to deformation than the thinner and denser biofilms (tin and groundwater biofilms).