Biocomposites For Applications Research Articles

Rheology of Cellulosic Microfiber Suspensions Under Oscillatory and Rotational Shear for Biocomposite Applications

This study investigates the rheological behavior of cellulose microfiber suspensions derived from kahili ginger stems (Hedychium gardnerianum), an invasive species, in two adhesive matrices: a commercial water-based adhesive (Coplaseal®) and a casein-based adhesive made from non-food-grade milk, referred to as K and S samples, respectively. Rheological analyses were performed using oscillatory and rotational shear tests conducted at 25 °C, 50 °C, and 75 °C to assess the materials’ viscoelastic properties more comprehensively. Oscillatory tests across a frequency range of 1–100 rad/s assessed the storage modulus (G′) and loss modulus (G″), while rotational shear tests evaluated apparent viscosity and shear stress across shear rates from 0.1 to 1000 s−1. Fiber-free samples consistently showed lower moduli than fiber-containing samples at all frequencies. The incorporation of fibers increased the dynamic moduli in both K and S samples, with a quasi-plateau observed at lower frequencies, suggesting solid-like behavior. This trend was consistent in all tested temperatures. As frequencies increased, the fiber network was disrupted, transitioning the samples to fluid-like behavior, with a marked increase in G′ and G″. This transition was more pronounced in K samples, especially above 10 rad/s at 25 °C and 50 °C, but less evident at 75 °C. This shift from solid-like to fluid-like behavior reflects the transition from percolation effects at low frequencies to matrix-dominated responses at high frequencies. In contrast, S samples displayed a wider frequency range for the quasi-plateau, with less pronounced moduli changes at higher frequencies. At 75 °C, the moduli of fiber-containing and fiber-free S samples nearly converged at higher frequencies, indicating similar effects of the fiber and matrix components. Both fiber-reinforced and non-reinforced suspensions exhibited pseudoplastic (shear-thinning) behavior. Fiber-containing samples exhibited higher initial viscosity, with K samples displaying greater differences between fiber-reinforced and non-reinforced systems compared to S samples, where the gap was narrower. Interestingly, S samples exhibited overall higher viscosity than K samples, implying a reduced influence of fibers on the viscosity in the S matrix. This preliminary study highlights the complex interactions between cellulosic fiber networks, adhesive matrices, and rheological conditions. The findings provide a foundation for optimizing the development of sustainable biocomposites, particularly in applications requiring precise tuning of rheological properties.

Applications of bio-composites in electronics

Abstract Functional biomaterials are being used in many promising industries to improve human quality of life and advance environmental objectives. Consideration has been given to many applications in the domains of medical, electronics, food, and pharmaceuticals. The use of bio-inspired materials enables the creation of more sustainable alternatives that strive to advance environmental preservation while simultaneously ensuring customer satisfaction. It was discovered that biopolymers are used in a number of different industries for the production of a wide range of functional bio-products. These bio-products include organic thin film transistors, organic phototransistors, emitting diodes, photodiodes, photovoltaic solar cells, hybrid dental resins, sustainable medicines, and consumer food packaging. A growth of this magnitude makes it possible to conduct substantial research in order to more inspection of the limitless requests and uses of bio-based composites. In order to fulfill the needs of certain applications, it is necessary to adjust and reassess attributes and parameters– such as hardness, durability, crack toughness, binding, solubility, polarization, plasticity, hydrogen bonding, thermal characteristics, and dielectric behavior. By virtue of their electronic and electrical properties, bio-composites and biopolymers have been put to use in a variety of applications; some includes organic thin-film transistors, electrical applications, electromagnetic insulation, energy harvesting, and thermoelectric processes. Substantial proportions of electronic waste, also referred to as E-waste, are regularly released into the environment due to the continuous growth in the production of electronic devices. Consequently, this leads to substantial environmental and ecological problems caused by the release of non-degradable polymers, hazardous compounds, and toxic heavy metals into the environment. The advancement of biodegradable polymers has significant potential for effectively reducing the environmental burden, since they may be decomposed or absorbed into the surrounding environment without generating any toxic effects. Hence, the purpose of this study is to illustrate the creation of biocompatible composites and their prospective uses in electrical applications.

Synthesis and application of chitosan and orange peel biocomposites for cadmium (II) removal from water

Synthesis and application of chitosan and orange peel biocomposites for cadmium (II) removal from water

Unveiling the untapped potential of Hibiscus Rosa-sinensis lignocellulosic fiber: A multifaceted characterization for advancing sustainable biocomposite applications

In the pursuit of sustainable advancements in bio-inspired fiber reinforced polymer composite materials, the exploration of novel natural fibers has become a focal point of research. This experimental study aims to elucidate the unexplored potential of Hibiscus Rosa-sinensis fiber (HRF) as a versatile reinforcement material for high-performance composites. Through an integrated approach, this research offers a meticulous analysis of the HRF's physico-chemical properties, and single fiber tensile strength. The crystalline structure are revealed by X-ray diffraction (XRD), thermal behavior are characterized through thermo-gravimetric analysis (TGA), and surface morphology has been visualized using field emission scanning electron microscopy (FESEM) studies. From the results, it is found that the HRF contains a cellulose content of 79.50 %, positioning it as a prime bast fiber among its counterparts. This composition is complemented by hemicellulose (10.36 %), lignin (4.62 %), wax (0.84 %), and ash (2.96 %). The Fourier-transform infrared spectroscopy (FTIR) spectra unveils the intricate functional groups present in the fibers. XRD analysis highlights a crystallinity index (CI) of 66.93 %, confirming a well-organized and structured crystalline arrangement. The thermal stability established through TGA underscores HRF's resilience up to 284 °C, presenting it is an optimal reinforcement material for bio-inspired green composites operating within 280 °C. The surface morphology of HRF is examined through FESEM and three-dimensional profiling, showcasing its inherent morphological intricacies. The multidimensional characterization provided herein contributes significantly to the evolving landscape of biocomposite research, fostering a platform for future advancements and innovations in HRF-based composite materials.

Ultrafast and one-step coating sporopollenin exine capsules with metal-phenolic networks for bio-composite applications

Sporopollenin exine capsules (SECs), extracted from plant pollen grains, are becoming increasingly popular as natural microcapsules for a broad spectrum of bio-composite applications due to their plentiful supply, resilience to chemicals and physical stress, unique species-specific designs, exceptional consistency in structure, and significant internal volume. However, SECs have a relatively bioinert interface hindering their application in biomaterials. Thus, surface modification is an efficient strategy to convert SECs into biocompatible materials better for biological applications. Previous approaches predominantly depend on labor-intensive, multi-stage procedures that are time-consuming. Herein, we report an ultrafast, one-step, and effective modification strategy to render SECs biocompatibility by coating them with ferric ions and tannic acids, which endow them with a better cell adhesion property. In summary, our results show that this ultrafast and one-step biocompatibility strategy enhances the functional characteristics of SECs and holds wide-ranging implications for bio-composite applications..

Extraction and Characterization of Microcrystalline Cellulose (MCC) from Durian Rind for Biocomposite Application

AbstractThe scientific community has become interested in cellulose extraction from agro-industrial wastes because they contain large quantities of cellulose and are being researched globally due to their application. Cellulose extracted from these wastes offers varying characteristics and structures depending on the specific source. In this study, microcrystalline cellulose (MCC) was extracted from different parts of the durian husk through acid hydrolysis with various concentrations of oxalic acid and cellulose-to-acid ratios. The durian husk underwent a pretreatment method involving bleaching and alkaline treatment. The characteristics of MCC, such as functional group, morphology, and crystallinity, were studied. The findings indicated that lignin was successfully removed through pretreatment. However, traces of hemicellulose were still detected in a few samples. The extracted MCCs demonstrated a diameter range from 6.237 to 25.38 μm and crystallinity within the range of 71.43–78.30%. Polycaprolactone (PCL)-based biocomposites with different MCC weights (0.2, 0.5, and 1.0 wt%) were fabricated, and the performance was evaluated through tensile testing and biodegradability tests. The addition of 1.0 wt% MCC enhanced the tensile strength by 22%. SEM analysis revealed the cross-section fracture surface of the biocomposite, indicating the contribution of the MCC during pull-out. Meanwhile, the biodegradability of the biocomposite increased with the addition of MCC, indicating that the MCC-based biocomposite was fully biodegradable.

Nano-fumed silica coated novel cellulosic okra fabrics with enhanced hydrophobic, mechanical and thermal properties for high performance bio-composite applications

Nano-fumed silica coated novel cellulosic okra fabrics with enhanced hydrophobic, mechanical and thermal properties for high performance bio-composite applications

Cellulose Nanofibrils Dewatered with Poly(Lactic Acid) for Improved Bio-Polymer Nanocomposite Processing.

Cellulose nanofibrils (CNFs) have theoretically ideal properties for bio-based composite applications; however, the incorporation of these materials into polymers is made challenging by the strong binding of water to CNFs and the irreversible agglomeration of CNFs during drying. Previous methods used "contact dewatering", wherein the addition of wood flour (WF) to CNFs facilitated the mechanical removal of water from the system via cold pressing, which showed potential in producing dried CNF fibrils attached to wood fibers for biocomposite applications. In this work, the viability of contact dewatering with poly(lactic) acid (PLA) powder for PLA/CNF composites was evaluated. The energy efficiency of dewatering, preservation of nanoscale CNF morphology, and mechanical properties were examined by mixing wet CNFs with pulverized PLA at various loading levels, pressing water out of the system, and compression molding and shear mixing composites for testing. The most impressive results from this dewatering method were the preservation of micron-to-nanoscale fibers with high aspect ratios in PLA-CNF composites; increased strength and modulus of 1.7% and 4.2%, respectively, compared to neat PLA; equivalent or better properties than spray-dried nanocellulose at similar loading levels; and an 11-194x reduction in drying energy compared to spray-drying CNFs.

Integration of recycled denim waste cotton fibre and jute fibre in thermoplastic bio composite applications

High-stiffness and high-strength natural fibres are commonly utilized in thermoplastic matrices to manufacture biobased thermoplastic composites. Low-end applications such as construction and furniture industries do not require a high load-bearing capacity, thus favoring cost-effective, moderately strong, sustainable natural materials and quickly manufacture thermoplastic composites. Recycled biobased cotton fibres collected from the denim industry can effectively penetrate this composite industry due to their cost-effectiveness and desirable physical and mechanical properties. However, retaining structural integrity and enhancing the reinforcing efficiency of recycled yarns in composites pose challenges. Addressing these issues, we propose a new method of extracting recycled cotton from denim waste fabric and transforming it into dry preform with minimal damage to the structural integrity of cotton fibres. Jute fibres have been introduced alongside recycled denim fibers within a polypropylene matrix to optimize the hybrid reinforcing efficacy of the composites. The effect of denim fibre length on composite quasi-static tensile and flexural test results showed that a yarn length of 20 mm yielded the highest tensile strength (⁓27.83 MPa), tensile modulus (⁓ 1.76 GPa), flexural strength (⁓62.35 MPa), and flexural modulus (⁓1.17 GPa). Composites comprising recycled denim yarn and jute fibre improved the tensile modulus to approximately ⁓2.1 GPa and the impact strength to approximately ⁓66.1 kJ/m2, following the hybrid rule of mixture, while jute fiber serves to increase the stiffness and toughness of the composites. This work demonstrates that recycled denim cotton fibre and strong jute fibre can be successfully integrated into thermoplastic composites to achieve tailored mechanical properties.

ALKALINE TREATMENT OF SUGARCANE BAGASSE FIBERS FOR BIOCOMPOSITE APPLICATIONS

This study investigates the mechanical, structural, morphological, and thermal properties of chemically treated and untreated sugarcane bagasse fibers (SCB). Various concentrations of NaOH were used for the treatment over four hours. The main goal was to investigate the impact of alkali treatment on the overall properties of SCB fibers intended for composite applications. The results indicated that the crystallinity index, thermal stability, and mechanical properties were improved with the treatment, and this is due to the removal of impurities initially present on the outer surface of the SCB fiber and the reduction of amorphous components. This improvement may facilitate better adhesion between the SCB fibers and the polymeric matrices in biocomposite applications. However, it is important to determine the optimal concentration of NaOH that improves the properties of the SCB fiber without damaging the fiber’s structure.

Evaluation of mechanical, thermal, and morphological properties of novel cellulosic bio-fiber from Licuala grandis peduncle for lightweight biocomposite applications

Evaluation of mechanical, thermal, and morphological properties of novel cellulosic bio-fiber from Licuala grandis peduncle for lightweight biocomposite applications

Evaluation of the potential of Yushina alpina bamboo fibers from Cameroon for the manufacture of biocomposites

The Cameroon has two bamboo species indigenous to Africa (the alpine bamboo, Yushina alpina and the savannah bamboo, Oxytenanthera abyssinica), and one largely exotic species, Bambusa vulgaris. However, little on their physical characteristics and strength for the composites materials applications is known for these two indigenous bamboos species in Cameroon. Therefore, in this study, emphasis was laid on the alpine bamboo Y. alpina, to evaluate its potential for biocomposites applications. Y. alpina with ages ranging from 1 to 3 years, 4–5 years, and 7 years were characterized. The mechanical and physical properties of these three age ranges were compared. In the first place, the surface texture of the fibers was examined by scanning electron microscopy. Afterwards, chemical treatment was performed on the fibers with 1 % NaOH. In addition, the chemical bonds of the molecules (functional groups) were identified by Fourier transform infrared spectra (FTIR) and the thermal properties of the fibers were examined with a thermogravimetric analyzer. Furthermore, the fibers density was assessed using the Rilem protocol and a tensile testing machine was used to determine the mechanical properties of the treated fibers with 1 % of NaOH. Finally, a dynamic mechanical analysis of 7-year-old Y. alpina fibers was carry out. The results indicate that the Young's modulus of treated fibers with ages ranging from 1 to 3 years, 4–5 years, and 7 years were around 18 GPa, 10 GPa, and 14 GPa, respectively. In summary, this study underlines two primary points: (1) providing a platform for researchers to better understand the influence of age on the physical and mechanical properties of indigenous bamboo Y. alpina; and (2) providing a platform to validate suitable designs of biocomposites materials with Y. alpina.

Effect of treatment conditions on the morphology of date empty fruit bunch lignocellulosic fiber for biocomposite applications

The fiber of the empty date fruit is one of the waste products left after the date fruit is harvested from the date palm. Optimization of the treatment parameters as well as the economics of the treatment process are critical to the successful commercialization of the treatment of natural fibers for the production of biocomposites. Of the natural fiber treatment methods described in previous work, hot water and alkali treatments are the most cost-effective, which justified the choice of these treatment methods in this work. Here, date empty fruit bunch fibers were pulverized to a particle size of 0–500 µm and then treated with boiling water at 100 °C for 3 h or with sodium hydroxide at different concentrations (2, 5, 10%) for 3 h at room temperature with constant stirring at 800 rpm. To confirm the effect of temperature on the fiber treatment, another fiber sample was treated at a 5% concentration of sodium hydroxide solution at an elevated temperature of 80 °C for the same period and stirring condition. The untreated and treated DEFB fibers were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR), nuclear magnetic resonance (NMR), differential scanning calorimetry (DSC), X-ray fluorescence (XRF), and scanning electron microscopy (SEM). Chemical analysis of the fibers showed that DEFB fiber treated with 5% sodium hydroxide solution at room temperature had the highest cellulose content (52.0%), which was also confirmed by the XRD analysis. The DEFB fiber treated with boiling water exhibited higher thermal stability while the sodium hydroxide-treated fiber exhibited higher crystallinity index and cellulose content. Apparently, DEFB fiber treated with sodium hydroxide solution at 5% concentration for 3 h at room temperature for continuous stirring at 800 rpm offered the best properties. The treated fibers are expected to be viable reinforcement in the production of biocomposites with the goal of achieving energy efficiency. The developed materials could be used in industrial applications such as insulating building systems, automotive parts, and home furniture.

Comparative Review of Mechanical Properties of Rice Straw and RiceHusk Fiber Reinforced Polymer Composite

Rice straw and rice husk fibers (RS/RH) reinforced polymer-based composites have theability to conserve wood and petroleum resources. As natural filler, rice straw and rice husk offer asustainable material for the production of polymer-based composites. The application ofbiocomposite limits the burning of straw at the root and may further enhance the socioeconomicstatus of farmers and rural populations. This review mainly focuses on five different weightpercentage of reinforced RS and RH fiber content (5%, 10%, 15%, 20% and 25%) in polymercomposites. Nowadays, Epoxy, polyurethane, polyester, PVA, PLA and polyethylene are beingused as matrix material in polymer composites. This paper holds good with understanding themechanical properties, pretreatment methods and offer important insight into potential uses ofpolymer composites with biodegradable reinforce fiber.

Valorisation of Agricultural Residue Bio-Mass Date Palm Fibre in Dry-Blended Polycaprolactone (PCL) Bio-Composites for Sustainable Packaging Applications

Abstract Purpose This study experimentally developed and characterised dry-blended Polycaprolactone (PCL)/date palm fibre biodegradable composites for sustainable packaging applications. Date palm fibres are collected from date palm trees as by-products or waste materials. They will be valorised in bio-composite application to promote fibre-based sustainable packaging items over their non-biodegradable synthetic polymer based conventional packaging products. In the dry-blending process, fibre and polymer are mixed with a shear mixer, while, in a melt-blending process, an extruder is used to extrude fibre/polymer blends after applying heating and high shear pressure to melt and mix polymer with fibres. Dry-blending process offers many comparative advantages, such as less equipment, steps, cost, process degradation, energy consumption and hence, lower harmful environmental emissions; while, a proper fibre/polymer mixing is a challenge and it needs to be achieved properly in this process. Therefore, it is important to understand the effects of dry-blending process on manufacturing of PCL/date palm fibre bio-composites for packaging applications, before promoting the dry-blending as a suitable alternative to the melt-blending process. Methods Short chopped fibres were grinded as powders and dry-blended at a ratio of (0 − 10%) (w/w) with PCL polymer using hand and a shear mixer for 30 min, following a compression moulding process to produce bio-composite samples. Tensile, water contact angle, SEM, TGA, DSC and DMA tests and analysis were conducted. The dry-blended PCL/date palm fibre composites’ properties were compared with reported melt-blended samples’ results found in literature. Results Dry-blended samples showed an increase in tensile modulus values (up-to 20%) with fibre inclusion and these values were found close to the melt-blended samples in the literature. Tensile strength and strain values were reduced which could be related to the poor fibre/polymer interface. Fibre addition affected the thermal, thermo-mechanical and crystallisation processes in PCL polymer matrix. Conclusion Dry-blending is capable of producing bio-composites with a very comparable properties to melt-blended counterparts, although a more details study is needed to conduct in future. The results of this study, could be used carefully to design dry-blended PCL/date palm fibre bio-composites for possible packaging applications. The irregular fibre distribution in dry-blended samples could be improved in different ways which should be investigated in future. Graphical Abstract

An experimental review on enhancing the low and high-velocity impact resistance of NFCs through nanoparticle reinforcement

Nanoparticles are widely used in biocomposite materials due to their ability to improve the mechanical properties of composites. This comprehensive review analyzes the use of nanoparticles to enhance the experimental low and high-velocity impact resistance of natural fiber composites. Various nanoparticles like carbon nanofibers, carbon nanotubes, boron nitride, zinc oxide, and titanium dioxide were investigated as reinforcements at different loading levels. The addition of nano-ZrO2 alone or with graphene oxide yielded the highest impact resistance and interlaminar shear strength of basalt fiber/epoxy composites. Cloisite 20A clay improved the mechanical properties of an epoxy matrix. Carbon/epoxy laminates showed improved maximum impact force, energy absorption, and displacement with 2wt% carbon nanofibers loading. Nanoparticles were found to enhance moisture and temperature resistance by strengthening the fiber–matrix interface. The literature demonstrated that small amounts of well-dispersed nanoparticles can meaningfully improve natural fiber composites’ impact resistance, strength, stiffness, toughness, and energy absorption through mechanisms like crack arresting and bridging. Hybrid carbon-basalt fibers and calcium carbonate nanoparticles also enhanced composite performance. Balancing the nanoparticle loading is crucial to prevent agglomeration effects. Future studies on their toxicity and environmental impacts would be needed for widespread commercial applications of Biocomposites.

Application of Gaba-Gaba Egg Rack Bio-Composite as Material Wall Meeting Room Acoustics

Bio composite materials are a combination of two or more natural polymer materials or biofiber (natural fibers) which can be degraded as reinforcement and polymer or matrix. Natural fibers generally have the ability to absorb sound well and have basic properties as composite reinforcements. If a wave hits a material, the wave can be straightened, reflected and absorbed. The ability of composite structures to absorb sound can be used to reduce noise levels. This research models a combination of egg rack waste mixed with sago leaf stem (gaba-gaba) waste as a bio-composite material for room acoustic panels. This research uses a material modeling engineering method which is a pure experiment, with the stages of making test samples based on fixed variables and measurable variables and then testing to obtain the material absorption coefficient, then the test results are based on the specified variables, then applying the material to the meeting room. After that tested the acoustic level of the room, especially the meeting room.

Insights into adsorption performance and mechanism of chitosan-bentonite biocomposites for removal of imazethapyr and imazamox

In the present study, chitosan-bentonite biocomposites were synthesised by ultrasonication, characterized using spectral techniques and assessed for their effectiveness in removing imazethapyr and imazamox from aqueous solution. The response surface methodology based box behnken design was utilized to generate optimum conditions viz. pH (1 to 9), adsorbent dose (0.01 to 1.0 g), contact time (0.5 to 48 h) and temperature (15 to 55 °C) for adsorption of herbicides on biocomposites. Based on model predictions, 60.4 to 91.5 % of imazethapyr and 31.7 to 46.4 % of imazamox was efficiently removed under optimal conditions. Adsorption data exhibited a strong fit to pseudo-second-order kinetic (R2 > 0.987) and Freundlich isotherm (R2 > 0.979). The adsorption capacity ranged from 3.88 to 112 μg1−ng−1mLn and order of adsorption was: low molecular weight chitosan-bentonite> medium molecular weight chitosan-bentonite> high molecular weight chitosan-bentonite> bentonite. Thermodynamic experiments suggested a spontaneous, exothermic process, reducing the system randomness during adsorption. Desorption experiments revealed successful desorption ranging from 91.5 to 97.0 % using 0.1 M NaOH. The adsorption mechanism was dominated by synergistic electrostatic interactions and hydrogen bonding. These results collectively indicated the potential environmental remediation application of chitosan-bentonite biocomposites to adsorb imazethapyr and imazamox from wastewaters.

Characterization of Water Absorption, Thickness Swelling and Diffusion Coefficient of Natural Fiber/Epoxy Bio-Composites for Applications in Aquatic Environment

The aim of this work was to study the suitability of wood flour, fluted pumpkin stem and rice husk flour/epoxy bio-composites for application in aquatic environment. The water absorption, thickness swelling and diffusion coefficient of wood flour, fluted pumpkin stem flour, rice husk flour/epoxy bio-composites were investigated. Composites were prepared by the hand layup method at varying weight percentages of filler reinforcement (10, 20 & 30%). The increase in the addition of the fillers enhanced the water absorption, thickness swelling and diffusion coefficient of the composites. However, after 14 days of immersion, all the composites attained an equilibrium state. It was observed that with 30wt% filler loading, the fluted pumpkin stem flour epoxy composites showed the highest water absorption of 40.5%, diffusion coefficient of 10.80x10-8m2/s, followed by the wood flour epoxy composite with water absorption of 35.3%, diffusion coefficient of 8.17x10-8m2/s, while rice husk flour epoxy composites had the lowest water absorption of 16.5%, diffusion coefficient of 6.12x10-8m2/s. The same trend was observed for the composites with 20 and 10 wt% filler loading. In terms of thickness swelling, the wood flour composite showed 1.62%, followed by fluted pumpkin stem flour composite 1.40% and rice husk flour composite 0.35% with 30wt% filler loading. A similar trend was observed for the composites with 20 and 10wt% filler loading. This study can be useful to comprehend the effect of water absorption on the performance of natural fiber composites and help in creating designer compositions for use in building, construction and automotive.

Study of wound-healing properties of humic substance – zinc complexes in the aseptic wound model in vivo

The aim was to investigate wound-healing properties of zinc-containing biocomposites based on humic ligands (humic substance (HS) – Zn) in the in vivo experiment on the aseptic wound model and to evaluate their resorptive properties.Materials and methods. The objects of the study were 5 samples of HS-Zn in the form of complex salts comprising fine black powders synthesized in the Laboratory for Natural Humic Systems of the Faculty of Chemistry at Moscow State University. The wound-healing effect of the substances was studied on 70 male Wistar rats using a traumatic model of an excisional aseptic skin wound. The degree of affected skin healing was evaluated during 21 days by the planimetric method. The resorptive properties of the HS-Zn samples were studied by inductively coupled plasma mass spectrometry (ICP-MS) in the biomaterial (blood serum, fur, skin from the wound surface).Results. It was found that course application of zinc-containing HS-Zn biocomposites to the wound surface led to a decrease in the wound area in comparison with ZnSO4 with the equivalent concentration of elemental Zn (1.67 mg/ ml). Two samples FA-Zn and Peat1-Zn showed the most pronounced regenerating effect. We noted an increase in Zn level in the tested skin samples from the wound area, in fur, and in the blood serum, which indicates the resorptive effect of zinc-containing HS-Zn biocomposites during course application; however, the parameters did not exceed limiting permissible concentrations. The correlation between the tested samples was not equal, which indicates a significant impact of the initial HS matrix on the Zn bioavailability.Conclusion. The observed reparative effect of zinc and HS complexes in the context of their low toxicity is of interest for further study to develop effective wound-healing preparations.