Silica Bilayers Research Articles

Ultrathin silica-tiling on living cells for chemobiotic catalysis

Harnessing the power of cell biocatalysis for sustainable chemical synthesis requires rational integration of living cells with the modern synthetic catalysts. Here, we develop silica-tiling strategy that constructs a hierarchical, inorganic, protocellular confined nanospace around the individual living cell to accommodate molecularly accessible abiotic catalytic sites. This empowers the living microorganisms for new-to-nature chemical synthesis without compromising the cellular regenerative process. Yeast cell, a widely used biocatalyst, is upgraded via highly controlled self-assembly of 2D-bilayer silica-based catalytic modules on cell surfaces, opening the avenues for diverse chemobiotic reactions. For example, combining [AuPt]-catalyzed NADH regeneration, light-induced [Pd]-catalyzed C-C cross-coupling or lipase-catalyzed esterification reactions—with the natural ketoreductase activity inside yeast cell. The conformal silica bilayer provides protection while allowing proximity to catalytic sites and preserving natural cell viability and proliferation. These living nanobiohybrids offer to bridge cell’s natural biocatalytic capabilities with customizable heterogeneous metal catalysis, enabling programmable reaction sequences for sustainable chemical synthesis.

Interface Effects in the Stability of 2D Silica, Silicide, and Silicene on Pt(111) and Rh(111).

Ultrathin two-dimensional silica films have been suggested as highly defined conductive models for fundamental studies on silica-supported catalyst particles. Key requirements in this context are closed silica films that isolate the gas phase from the underlying metal substrate and stability under reaction conditions. Here, we present silica bilayer films grown on Pt(111) and Rh(111) and characterize them by scanning tunneling microscopy and X-ray photoelectron spectroscopy. We provide the first report of silica bilayer films on Rh(111) and have further successfully prepared fully closed films on Pt(111). Interestingly, surface and interface silicide phases play a decisive role in both cases: On platinum, closed films can be stabilized only when silicon is deposited in excess, which results in an interfacial silicide or silicate layer. We show that these silica films can also be grown directly from a surface silicide phase. In the case of rhodium, the silica phase is less stable and can be reduced to a silicide in reductive environments. Though similar in appearance to the "silicene" phases that have been controversially discussed on Ag(111), we conclude that an interpretation of the phase as a surface silicide is more consistent with our data. Finally, we show that the silica film on platinum is stable in 0.8 mbar CO but unstable at elevated temperatures. We thus conclude that these systems are only suitable as model catalyst supports to a limited extent.

Tuning the Poisson’s ratio of two-dimensional model network materials with application to 2D-silica bilayer structures

A fundamental understanding of the elastic properties of 2D network structures is highly beneficial for research and applications of 2D materials. In this context, Poisson’s ratio has been studied elaborately for different crystallographic structures of crystalline phases of bilayer silica structures. This paper focuses on the elastic structure–property relationship of crystalline and vitreous polymorphs of plane network materials. We generate defective crystalline network states and seven sets of disordered states, each with a different level of network heterogeneity, using a dual Monte Carlo bond switching algorithm. Firstly, uniaxial tensile deformation is applied to a model material in a two-dimensional framework, concentrating only on the in-plane network topologies. Secondly, uniaxial tensile deformation is applied to bilayer silica structures, considering the out-of-plane morphology of the material. Mechanical testing is performed using the athermal quasistatic deformation protocol, which allows one to study the influence of the network topology exclusively without any thermal disturbances. We show that manipulating the network heterogeneity allows one to directly tune the Poisson’s ratio of the material, creating possibilities for novel mechanical applications.

Catalytic atomic layer deposition of amorphous alumina–silica thin films on carbon microfibers

Deposition of silica-based thin films on carbon microfibers has long been considered a challenge. Indeed, the oxidation-sensitive nature of carbon microfibers over 550 K and their submicron-textured surface does not bode well with the required conformity of deposition best obtained by atomic layer deposition (ALD) and the thermal oxidative conditions associated with common protocols of silica ALD. Nonetheless, the use of a catalytic ALD process allowed for the deposition of amorphous alumina–silica bilayers from 445 K using trimethylaluminium and tris(tert-pentoxy)silanol (TPS). In this study, first undertaken on flat silicon wafers to make use of optical spectroscopies, the interplay between kinetics leading to a dense silica film growth was investigated in relation to the applied operation parameters. A threshold between the film catalyzed growth and the complete outgassing of pentoxy-derived compounds from TPS was found, resulting in a deposition of equivalent growth per cycle of 1.1 nm c−1, at a common ALD rate of 0.3 nm min−1, with a flat thickness gradient. The deposition on carbon microfiber fabrics was found conformal, albeit with a thickness growth capped below 20 nm, imparted by the microfiber surface texture. STEM-EDX showed a sharp interface of the bilayer with limited carbon diffusion. The conformal and dense deposition of alumina–silica thin films on carbon microfibers holds great potential for further use as refractory oxygen barrier layers.

Electrochemical Ultrathin Metal‐Atomic Layer Deposition for Silica Microenvironment‐Assisted Cu‐Based Catalysis

AbstractReplacing commonly used precious and rare noble metals by the abundant copper (Cu)‐based catalysts is highly desired for sustainable fine‐chemical synthesis. However, in the lack of model platforms, complex surface chemistry of randomly nanostructured bulk Cu is notoriously challenging to understand and control. By synthesizing ultrathin 2D‐Cu layer sandwiched inside the bilayer silica template, an unusual but critical cooperative role of Lewis basic amino‐silica microenvironment for [Cu]‐catalyzed selective hydrogenation of unsaturated C─C bonds in diverse alkynes, ene‐ynes, and α,β‐unsaturated (alkene) Michael acceptors is discovered. Newly developed nanospace‐confined electrochemical (eChem) atomic layer deposition (NC‐EAD) technique afforded < 2 nm ultrathin Cu(0)‐layer intimately covered inside silica envelope. This model platform aided the detailed mechanistic study deciphering the unexpected finding – originally non‐reactive Cu‐film, just by a simple silica coating step, turning into an efficient catalyst for scalable fine‐chemical synthesis. The concept of reactive metal surface‐microenvironment manipulation, presents a new paradigm for controlling complex molecular interactions in heterogeneous catalysts.

Nature of Interlayer Bonds in Two-Dimensional Materials

The role of interlayer bonds in the two-dimensional (2D) materials "beyond graphene" and so-called van der Waals heterostructures is vital, and understanding the nature of these bonds in terms of strength and type is essential due to a wide range of their prospective technological applications. However, this issue has not yet been properly addressed in the previous investigations devoted to 2D materials. In our work, by using first-principles calculations we perform a systematic study of the interlayer bonds and charge redistribution of several representative 2D materials that are traditionally referred as van der Waals systems. Our results demonstrate that one can distinguish three main types of inter-layer couplings in the considered 2D structures: one atom thick membranes bonded by London dispersion forces (graphene, hBN), systems with leading electrostatic interaction between layers (diselenides, InSe and bilayer silica) and materials with so-called dative or coordination chemical bonds between layers (ditelurides). We also propose a protocol for recognising the leading type of interlayer bonds in a system that includes comparison of interlayer distances, binding energies and redistribution of the charge densities in interlayer space. Such an approach is computationally cheap and can be used to further prediction of chemical and physical properties such as charge density waves (CDW), work function and chemical stability at ambient conditions.

Effects of monolayer and bilayer silica films on Fe-Phthalocyanine adsorption properties

We explore the adsorption properties of Fe-Phthalocyanine (FePc) molecule at various configurations of silica films supported by Ru(0001) and report on the geometric, electronic and magnetic features of the energetically preferred structures to fully understand the influence of the silica films on the adsorption properties of the FePc molecule. The investigation is carried out with the use of density of functional theory calculations and the self-consistent inclusion of van der Waals interaction. In addition, Oxygen atoms are added to govern the atomic structure of the silica overlayers on the surface. Our results show that both FePc/silica thin film systems exhibit both physisorption and chemisorption simultaneously. In addition, the FePc molecule on each substrate undergoes a symmetry reduction driven by mismatch with the substrates' symmetry as well as the breakup of the degenerate orbitals of Fe.

Size and Shape Exclusion in 2D Silicon Dioxide Membranes

2D membranes such as artificially perforated graphene are deemed to bring great advantages for molecular separation. However, there is a lack of structure-property correlations in graphene membranes as neither the atomic configurations nor the number of introduced sub-nanometer defects are known precisely. Recently, bilayer silica has emerged as an inherent 2D membrane with an unprecedentedly high areal density of well-defined pores. Mass transfer experiments with free-standing SiO2 bilayers demonstrated a strong preference for condensable fluids over inert species, and the measured membrane selectivity revealed a key role of intermolecular forces in ångstrom-scale openings. In this study, vapor permeation measurements are combined with quantitative adsorption experiments and density functional theory (DFT) calculations to get insights into the mechanism of surface-mediated transport in vitreous 2D silicon dioxide. The membranes are shown to exhibit molecular sieving performance when exposed to vaporous methanol, ethanol, isopropanol, and tert-butanol. The results are normalized to the coverage of physisorbed molecules and agree well with the calculated energy barriers.

Robust silica and carbon bilayers decorating spherical FeCo alloys for high-performance anti-corrosion microwave absorption

The requirements of microwave absorbers are increasing year by year. However, a great challenge is the coupling of high microwave absorption and corrosion-resistant. To solve these problems, herein, a robust FeCo@SiO2 @C gradient composite was designed through the Stöber method and chemical vapor deposition (CVD) technique to achieve efficient microwave absorption and anti-corrosion. These silica/carbon bilayers possess a rich interface structure, reduce the dielectric constant, and optimize impedance matching, which favors to address efficient microwave absorbing performance with a minimum reflection loss of − 43.93 dB at 7.89 GHz in case of the 4 mm matching thickness. After decorating the silica/carbon bilayers on the FeCo surface, the excellent corrosion shielding protection for the inner FeCo alloy was well addressed. And the polarization resistance increased from 1.21 × 105 Ω·cm2 to 4.65 × 105 Ω·cm2. The corrosion current decreased from 8.623 × 10−6 A/cm2 to 1.357 × 10−6 A/cm2. This high curie temperature magnetic/silica/carbon novel hybrid reduces electromagnetic pollution and opens up a new opportunity to construct an advanced microwave absorber with anti-corrosion function.

Plasma Functionalization of Silica Bilayer Polymorphs.

Ultrathin silica films are considered suitable two-dimensional model systems for the study of fundamental chemical and physical properties of all-silica zeolites and their derivatives, as well as novel supports for the stabilization of single atoms. In the present work, we report the creation of a new model catalytic support based on the surface functionalization of different silica bilayer (BL) polymorphs with well-defined atomic structures. The functionalization is carried out by means of in situ H-plasma treatments at room temperature. Low energy electron diffraction and microscopy data indicate that the atomic structure of the films remains unchanged upon treatment. Comparing the experimental results (photoemission and infrared absorption spectra) with density functional theory simulations shows that H2 is added via the heterolytic dissociation of an interlayer Si-O-Si siloxane bond and the subsequent formation of a hydroxyl and a hydride group in the top and bottom layers of the silica film, respectively. Functionalization of the silica films constitutes the first step into the development of a new type of model system of single-atom catalysts where metal atoms with different affinities for the functional groups can be anchored in the SiO2 matrix in well-established positions. In this way, synergistic and confinement effects between the active centers can be studied in a controlled manner.

Carrier trapping centers in a two-dimensional silica bilayer: Strongly localized shallow gap states and resonances induced by oxygen vacancies

Structural and electronic properties of neutral native defects in a two-dimensional ${\mathrm{SiO}}_{2}$ bilayer (2D-${\mathrm{SiO}}_{2}$) are examined using the SIESTA ab initio approach. We identify scissor and rotation modes of oxygen atoms, in the middle of Si-O-Si chains, as low-energy structural excitations responsible for the response of the 2D-${\mathrm{SiO}}_{2}$ lattice to the formation of all native defects in the present study. Furthermore, we find that oxygen native defects (single vacancies and interstitials) should be the most abundant defect species in thermal-equilibrated samples. Regarding native-defect electronic states, single oxygen vacancies and interstitials are found to be amphoteric trapping centers in 2D-${\mathrm{SiO}}_{2}$. Silicon vacancies and interstitials introduce several strongly localized states spanning a large fraction of the gap. Generally, we identify a marked tendency for the appearance of strongly spatially localized defect states, be their energies shallow or deep within the band gap, as well as the emergence of strongly localized resonances in the valence and/or conduction bands. Strong spatial localization of defect states, a hallmark of systems displaying trapping and polaronic effects, is a result of quantum confinement and enhanced Coulombic effects in this 2D system. Carrier trapping and polaron formation are thus expected to be a common feature of defect states and added carriers in 2D-${\mathrm{SiO}}_{2}$.

Bipolar silica nanochannel array confined electrochemiluminescence for ultrasensitive detection of SARS-CoV-2 antibody

Ultrasensitive, specific, and early identification of Coronavirus Disease (2019) (COVID-19) infection is critical to control virus spread and remains a global public health problem. Herein, we present a novel solid-state electrochemiluminescence (ECL) platform targeting severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) antibody with rapidity and ultrahigh sensitivity, in which a bipolar silica nanochannel array (bp-SNA) is fabricated on indium tin oxide (ITO) electrode for the first time to stably confine the ECL probe of tris(2,2′-bipyridyl) ruthenium (Ru(bpy)32+) under dual electrostatic force. The bp-SNA consists of tightly packed bilayer silica nanochannel array (SNA) with asymmetric surface charges, namely an inner negatively charged SNA (n-SNA) and an outer positively charged SNA (p-SNA), serving as an “electrostatic lock” to enrich and stabilize the cationic Ru(bpy)32+ probe without leakage from the electrode surface. The detection of SARS-CoV-2 IgG antibody could be realized via immobilization of SARS-CoV-2 spike protein on the utmost of Ru(bpy)32+-confined solid-state ECL platform (Ru@bp-SNA). Upon the capture of target SARS-CoV-2 IgG by immune recognition, the formed immunocomplex will block the nanochannel, leading to the hindered diffusion of the co-reactant (tri-n-propylamine, TPrA) and further producing a decreased ECL signal. The developed solid-stated ECL immunosensor is able to determine SARS-CoV-2 IgG with a wide linear range (5 pg mL−1 to 1 μg mL−1), a low limit-of-detection (2.9 pg mL−1), and a short incubation time (30 min). Furthermore, accurate analysis of SARS-CoV-2 IgG in real serum samples is also obtained by the sensor.

Two-Dimensional Ultrathin Silica Films.

Two-dimensional (2D) ultrathin silica films have the potential to reach technological importance in electronics and catalysis. Several well-defined 2D-silica structures have been synthesized so far. The silica bilayer represents a 2D material with SiO2 stoichiometry. It consists of precisely two layers of tetrahedral [SiO4] building blocks, corner connected via oxygen bridges, thus forming a self-saturated silicon dioxide sheet with a thickness of ∼0.5 nm. Inspired by recent successful preparations and characterizations of these 2D-silica model systems, scientists now can forge novel concepts for realistic systems, particularly by atomic-scale studies with the most powerful and advanced surface science techniques and density functional theory calculations. This Review provides a solid introduction to these recent developments, breakthroughs, and implications on ultrathin 2D-silica films, including their atomic/electronic structures, chemical modifications, atom/molecule adsorptions, and catalytic reactivity properties, which can help to stimulate further investigations and understandings of these fundamentally important 2D materials.

Electron-Stimulated Hydroxylation of Silica Bilayer Films Grown on Ru(0001): A Combined HREELS and EPR Study

Electron-Stimulated Hydroxylation of Silica Bilayer Films Grown on Ru(0001): A Combined HREELS and EPR Study

Mesoscopic Structures and Coexisting Phases in Silica Films

Silica films represent a unique two-dimensional film system, exhibiting both crystalline and vitreous forms. While much scientific work has focused on the atomic-scale features of this film system, mesoscale structures can play an important role for understanding confined space reactions and other applications of silica films. Here, we report on mesoscale structures in silica films grown under ultrahigh vacuum and examined with scanning tunneling microscopy (STM). Silica films can exhibit coexisting phases of monolayer, zigzag, and bilayer structures. Both holes in the film structure and atomic-scale substrate steps are observed to influence these coexisting phases. In particular, film regions bordering holes in silica bilayer films exhibit vitreous character, even in regions where the majority film structure is crystalline. At high coverages mixed zigzag and bilayer phases are observed at step edges, while at lower coverages silica phases with lower silicon densities are observed more prevalently near step edges. The STM images reveal that silica films exhibit rich structural diversity at the mesoscale.

Scalable production of single 2D van der Waals layers through atomic layer deposition: bilayer silica on metal foils and films

The self-limiting nature of atomic layer deposition (ALD) makes it an appealing option for growing single layers of two-dimensional van der Waals (2D-VDW) materials. In this paper it is demonstrated that a single layer of a 2D-VDW form of SiO2 can be grown by ALD on Au and Pd polycrystalline foils and epitaxial films. The silica was deposited by two cycles of bis(diethylamino) silane and oxygen plasma exposure at 525 K. Initial deposition produced a three-dimensionally disordered silica layer; however, subsequent annealing above 950 K drove a structural rearrangement resulting in 2D-VDW. The annealing could be performed at ambient pressure. Surface spectra recorded after annealing indicated that the two ALD cycles yielded close to the silica coverage obtained for 2D-VDW silica prepared by precision SiO deposition in ultra-high vacuum (UHV). Analysis of ALD-grown 2D-VDW silica on a Pd(111) film revealed the co-existence of amorphous and incommensurate crystalline 2D phases. In contrast, ALD growth on Au(111) films produced predominantly the amorphous phase while SiO deposition in UHV led to only the crystalline phase, suggesting that the choice of Si source can enable phase control.

Molecular Permeation in Freestanding Bilayer Silica.

Graphene and other single-layer structures are pursued as high-flux separation membranes, although imparting porosity endangers their crystalline integrity. In contrast, bilayer silica composed of corner-sharing (SiO4) units is foreseen to be permeable for small molecules due to its intrinsic lattice openings. This study sheds light on the mass transport properties of freestanding 2D SiO2 upon using atomic layer deposition (ALD) to grow large-area films on Au/mica substrates followed by transfer onto Si3N4 windows. Permeation experiments with gaseous and vaporous substances reveal the suspended material to be porous, but the membrane selectivity appears to diverge from the size exclusion principle. Whereas the passage of inert gas molecules is hindered with a permeance below 10-7 mol·s-1·m-2·Pa-1, condensable species like water are found to cross vitreous bilayer silica a thousand times faster in accordance with their superficial affinity. This work paves the way for bilayer oxides to be addressed as inherent 2D membranes.

Water Formation Reaction under Interfacial Confinement: Al0.25Si0.75O2 on O-Ru(0001).

Confined nanosized spaces at the interface between a metal and a seemingly inert material, such as a silicate, have recently been shown to influence the chemistry at the metal surface. In prior work, we observed that a bilayer (BL) silica on Ru(0001) can change the reaction pathway of the water formation reaction (WFR) near room temperature when compared to the bare metal. In this work, we looked at the effect of doping the silicate with Al, resulting in a stoichiometry of Al0.25Si0.75O2. We investigated the kinetics of WFR at elevated H2 pressures and various temperatures under interfacial confinement using ambient pressure X-ray photoelectron spectroscopy. The apparent activation energy was lower than that on bare Ru(0001) but higher than that on the BL-silica/Ru(0001). The apparent reaction order with respect to H2 was also determined. The increased residence time of water at the surface, resulting from the presence of the BL-aluminosilicate (and its subsequent electrostatic stabilization), favors the so-called disproportionation reaction pathway (*H2O + *O ↔ 2 *OH), but with a higher energy barrier than for pure BL-silica.

Exfoliating silica bilayers via intercalation at the silica/transition metal interface

The growth of the silica (SiO2) bilayer (BL) films on transition metal (TM) surfaces creates a new class of two-dimensional (2D) crystalline, self-contained materials that interact weakly with the TM substrate. The BL-silica/TM heterojunction has shown unique physical and chemical properties that can lead to new chemical reaction mechanisms under the sub-nm confinement and broad potential applications ranging from surface protection, nano transistors, molecular sieves to nuclear waste removal. Novel applications of BL-silica can be further explored as a constituent of van der Waals assembly of 2D materials. Key to these applications is an unmet technical challenge to exfoliate and transfer BL-silica films in a large area from one substrate to another without material damage. In this study, we propose a new exfoliation mechanism based on gas molecule intercalation from density functional theory studies of the BL-silica/TM heterojunction. We found that the intercalation of O atoms and CO molecules at the BL-silica/TM interface weakens the BL-silica—TM hybridization, which results in an exponential decrease of the exfoliation energy against the interface distance as the coverage of interfacial species increases. This new intercalation mechanism opens up the opportunity for non-damaging exfoliation and transfer of large area silica bilayers.

Structure and registry of the silica bilayer film on Ru(0001) as viewed by LEED and DFT.

Silica bilayers are stable on various metal substrates, including Ru(0001) that is used for the present study. In a systematic attempt to elucidate the detailed structure of the silica bilayer film and its registry to the metal substrate, we performed a low energy electron diffraction (I/V-LEED) study. The experimental work is accompanied by detailed calculations on the stability, orientation and dynamic properties of the bilayer at room temperature. It was determined, that the film shows a certain structural diversity within the unit cell of the metal substrate, which depends on the oxygen content at the metal-bilayer interface. In connection with the experimental I/V-LEED study, it became apparent, that a high-quality structure determination is only possible if several structural motifs are taken into account by superimposing bilayer structures with varying registry to the oxygen covered substrate. This result is conceptually in line with the recently observed statistical registry in layered 2D-compound materials.