Biaxial Flexural Strength Research Articles

Effect of the Intaglio Surface Treatment and Thickness of Different Types of Yttria-Stabilized Tetragonal Zirconia Polycrystalline Materials on the Flexural Strength: In-Vitro Study.

Surface treatment of the intaglio surface of zirconia is important for bonding. However, it could affect the strength of the materials. The purpose of this study is to compare the effect of laser, etching, and air abrasion surface treatment methods to a control group on the flexural strength of three zirconia materials with two different thicknesses. (1) Methods: A total of 120 disks were divided into three groups according to the type of zirconia and the ceramic thickness. Then, according to the surface treatment method, the groups were divided into four subdivisions. The change in the microstructure of the ceramic material was investigated through Scanning Electron Microscope (EVO LS10, Carl Zeiss SMT Ltd. Oberkochen, Germany). Phase identification was performed using an X-ray diffraction device (XRD; Ultimate IV X-ray Diffractometer, Rigaku Inc., Tokyo, Japan). The flexural strength was assessed with a biaxial flexural strength test in a universal testing machine. Data were analyzed using SPSS Software (SPSS version 26.0.Armonk, NY: IBM Corp). A three-way ANOVA and a post hoc Dunnett T3 test were employed to evaluate the effect of the yttria concentration, thickness, and surface treatment on the flexural strength of zirconia (α = 0.05). (2) Results: At 0.8 mm thickness, air abrasion significantly increased the flexural strength of 3Y-TZP (1130.6 ± 171.3 MPa) and 4Y-TZP (872 ± 108.6 MPa). However, air abrasion significantly decreased the flexural strength of 5Y-TZP materials (373 ± 46.8 MPa). Laser irradiation significantly decreased the flexural strength of 5Y-TZP (347 ± 50.3 MPa), while etching significantly decreased the flexural strength of both 3Y-TZP (530 ± 48.8) and 4Y-TZP (457.1 ± 57.3). When the thickness increased to 1 mm, air abrasion continued to significantly decrease the flexural strength of 5Y-TZP materials. (3) Conclusions: There was a negative effect of surface treatment on the flexural strength at 0.8 mm thickness rather than at 1 mm thickness. Air abrasion enhances the flexural strength of 3Y-TZP and 4Y-TZP materials but significantly reduces the flexural strength of 5Y-TZP materials. Zircos-E etching and Er:YAG surface treatment methods did not significantly reduce the flexural strength of 5Y-TZP materials at 1 mm thickness and can be recommended as an alternative surface treatment for 5Y-TZP materials.

Impact of speed sintering on the mechanical and optical properties of multilayered zirconia

Speed sintering techniques have been introduced to shorten the sintering time of zirconia ceramics, yet their impact on multilayered zirconia properties remains understudied. The purpose of this in vitro study was to assess the effect of speed sintering on the optical properties and the mechanical flexural strength of multilayered zirconia materials. A total of 360 disks (Ø14 ±2 mm ×1.2 ±0.02 mm) were fabricated by following the International Organization for Standardization (ISO) 6872:2015 standard using 2 types of Vita A2 shade multilayered zirconia materials: IPS e.max ZirCAD Prime (ZP) and IPS e.max ZirCAD Prime Esthetic (ZPE). Each material comprised translucent (Tr), gradient l (Gr), and dentin (De) layers, with 60 disks per layer. Half were sintered using a standard sintering protocol and half using a speed sintering protocol. Biaxial flexural strength was accessed using a universal testing machine equipped with the Blue Hill Universal software program by following the ISO 6872:2015 standard, with 20 disks per subgroup. The spectrophotometric analysis of optical properties (contrast ratio [CR], translucency parameter [TP], and total transmittance [Tt%]) was performed using a dual-beam spectrophotometer (Ultrascan VIS) in accordance with the ISO 7491:2000 standard, with 10 disks per subgroup. The comparison of the optical properties and the mechanical flexural strength between the speed and standard protocol was analyzed using an unpaired t test (α=.05). Speed sintering reduced biaxial flexural strength in all ZP layers (P<.05) and in ZPE-Gr (P<.05). A statistically significant difference in the CR was observed in the ZP-Tr, ZP-Gr, and ZPE-Gr layers (P<.05). The TP of the ZP-Gr, ZP-De, and ZPE-Gr layers was significantly lower when using the speed sintering protocol. Tt% was significantly lower with speed sintering for both materials (P<.05). Speed sintering statistically changed both the optical (CR, TP, Tt%) and mechanical (flexural strength) properties of multilayered zirconia materials, but the differences may not be clinically relevant.

Effect of sintering cycle on the strength and translucency of multilayered zirconia.

A newly introduced sintering protocol promises to offer higher translucency while not significantly compromising the flexural strength of the material. However, the effect of the novel sintering protocol has not been thoroughly validated. The purpose of this study was to measure and compare the effect of two sintering protocols on the translucency and flexural strength of two multilayered zirconia materials. Two types of multilayered zirconia materials (ZirCAD Prime and Prime esthetic) were selected. Presintered disk specimens were obtained from Translucent, Gradient, and Dentin layers (n = 20). The disks were allocated to 2 groups: standard sintering protocol (peak temperature 1500°C) and high translucency sintering protocol (peak temperature 1600°C). After the sintering process, 10 specimens from each group were randomly selected. The optical values (L*, a*, b*) were measured and used to assess translucency using the relative translucency parameter (RTP00) and translucency differences (ΔRTP00). Then, all 20 specimens were tested for biaxial flexural strength. The outcomes were analyzed. The analysis of variance is used to analyze any significant effects on translucency and flexural strength. Then, any significant difference in the translucency and flexural strength between all pairs of materials was analyzed using Bonferroni-corrected Student's t-test (α = 0.05). The high translucency sintering protocol significantly decreased biaxial strength in the Prime translucent and dentine layer, Prime esthetic translucent, and gradient layer. RTP00 was significantly reduced in the Prime gradient and Prime esthetic gradient layer when sintered with a high translucency protocol. The lowest ΔRTP00 was observed in the Prime dentine layer, while the highest ΔRTP00 was observed in the Prime esthetic dentin layer. High translucency protocol significantly lowers the biaxial flexural strength of both multilayered materials, but the alteration in translucency is within clinically acceptable thresholds (TAT00 = 2.62).

Fatigue strength of bilayer yttria-stabilized zirconia after low-temperature degradation

This study examined the impact of interfacial interactions on bilayer yttria-stabilized zirconia (YSZ) used in dental restorations. In-house bilayer structures of 3YSZ and 5YSZ composition underwent hydrothermal degradation to compare the properties of control and low-temperature degradation (LTD) treated groups. Biaxial flexural strength via piston-on-three-balls, staircase fatigue strength over 106 cycles at 15 Hz, phase characterization and quantification through XRD and Rietveld refinement, and fractography were conducted. Weibull analysis was employed to determine the Weibull modulus and characteristic strength. Results demonstrated an enhancement in the mechanical performance of 3YSZ composition after LTD treatment, whereas the mechanical properties of 5YSZ remained largely unaffected post-degradation. Fractographic analysis revealed that failure originated at the surface tensile location across all specimen groups. These findings offer insights into the mechanical behavior of bilayer zirconia structures and reinforce the significance of hydrothermal treatment in enhancing their performance, particularly in the case of 3Y compositions.

Densification and network structural changes in binary aluminosilicate glass via cold sintering process

Binary aluminosilicate glasses containing 20–50 wt% Al2O3 were successfully densified through a cold sintering process (CSP) using 1–10 M NaOH solutions. The investigation focused on densification and structural unit changes in the cold-sintered binary aluminosilicate glasses. Specifically, the binary aluminosilicate glass with 40 wt% Al2O3, cold-sintered at 180 °C using 1–10 M NaOH solutions, achieved a relative density of up to 90 % at 10 M NaOH. This was attributed to an enhanced dissolution-precipitation process facilitated by an increased concentration of the NaOH solution. In aluminosilicate glasses with 20–50 wt% Al2O3, the relative densities approached 90 % after CSP at 180 °C using a 10 M NaOH solution. Al(OH)3 formation in the cold-sintered glasses was confirmed, particularly at higher concentrations of NaOH solution (>10 M) and higher contents of Al2O3 (>40 wt%). Changes in Si structural units were observed during CSP, with Al-rich Si units becoming dominant as the concentration of the NaOH solution increased. The higher substitution of Si-O-Si bonds by Si-O-Al bonds led to the precipitation of Al(OH)3, as well as an increased Vickers hardness and biaxial flexural strength of the cold-sintered glasses. These findings demonstrate that the Al2O3 content and NaOH concentration play important roles in the densification and enhancement of the mechanical property in the cold-sintered alumina-rich binary aluminosilicate glasses and offer insights into the optimal conditions for obtaining desirable aluminosilicate materials through CSP.

Effect of elastic gradients on the fracture resistance of tri-layer restorative systems

ObjectivesTo assess the impact of elastic gradients formed among restorative material, cement, and substrate on the fracture resistance of tri-layer restorative systems. MethodsFour CAD/CAM materials were utilized, two glass-ceramics (IPS e.max CAD, Vita Suprinity) and two resin-ceramic hybrids (Vita Enamic, Lava Ultimate). Their fracture resistance was examined by biaxial flexure (n = 8) and Hertzian indentation (n = 10) tests. Statistical analysis was conducted using ANOVA and Tukey tests (p = 5 %). Finite element analysis (FEA) was employed to simulate the Hertzian indentation test and elucidate the stress-fields formed on the intaglio surface below the loading area. ResultsThe biaxial flexural strength (MPa) of glass-ceramics exceeded the hybrid materials (e.max 417a, Suprinity 230b, Enamic 138c, and Lava Ultimate 183bc). Conversely, the load-bearing capacity (N) of the materials bonded to dentin analog demonstrated the opposite trend, with the hybrid materials achieving superior results (e.max 830 C, Suprinity 660D, Enamic 1822B, and Lava Ultimate 2593 A). The stress-fields observed by FEA were coherent with the experimental results for Hertzian flexural stresses (MPa): e.max 501 A, Suprinity 342 C, Enamic 406B, whereas no tensile stress was observed at the intaglio surface of Lava Ultimate. SignificanceDetailed analysis of the fracture resistance of the tri-layer restorative systems showed that the elastic gradients play a more significant role than the flexural strength of the restorative materials. The coherence of the elastic moduli between the restorative material and supporting structures results in reduced tensile stress concentration at the intaglio surface beneath the loading area and enhances the ability to withstand load.

Effect of Successive At-home Bleaching Sessions on the Surface Properties, Biaxial Flexural Strength, and Reliability of CAD-CAM Monolithic Materials.

Although at-home bleaching can recover the optical properties of stained CAD-CAM monolithic materials, little is known about its impact on their surface and mechanical properties, especially when successive sessions are performed. This study evaluated the effect of successive at-home bleaching sessions on the microhardness, roughness, topography, biaxial flexural strength (BFS), and reliability of CAD-CAM monolithic materials. Disks from Lava Ultimate (LU), Vita Enamic (VE), and IPS Empress CAD (EMP) were fabricated and submitted to up to three bleaching sessions. At-home bleaching was performed with 10% carbamide peroxide, and each session consisted of one application for 10 hours/day for 14 days. The analyses of the aforementioned parameters were assessed before and after the first, second, and third bleaching sessions, except for BFS, which was evaluated at baseline and after the third session. The Weibull modulus was calculated from the BFS data. The microhardness of the three materials as well as the roughness of LU were not affected by the sessions, whereas the roughness of VE and EMP increased from the second session. All materials displayed topographic changes, which became more pronounced with the increase in the number of sessions. Although bleaching decreased the BFS of the materials, it did not adversely affect their reliability. Successive at-home bleaching sessions with the protocol used in the present study cannot be considered a safe procedure for the materials evaluated.

The impact of aging and thickness on flexural strength of various zirconia ceramics

BackgroundEffects of the aging process on the flexural strength of Y-TZP and different Y-PSZ ceramics of different thicknesses were investigated.Methods300 disc-shaped samples (12 mm diameter, 0.8 and 1.5 mm thicknesses) were made from 5 different zirconia materials 3Y-TZP LA, 4Y-PSZ, 5Y-PSZ, 3 + 5Y-PSZ and 4 + 5Y-PSZ. Experimental groups were artificially aged in an autoclave at 134 °C, 2 bar pressure for 1 and 5 h; control groups were not subjected to any treatment. Microstructural analysis was conducted using Scanning Electron Microscopy, and X-Ray Diffraction analysis determined the crystalline phase content. The impact of aging on flexural strength was investigated with the use of the biaxial flexural strength test. Data were analyzed using three-way ANOVA tests with a significance level of p < 0.05, applying Bonferroni correction for multiple comparisons.ResultsStatistically significant differences in flexural strength were observed among the materials and the material thicknesses (p < 0.05), while there were no significant differences among the aging times (p > 0.05). The highest mean flexural strength values were recorded in the case of the 3 Y-TZP-1.5 mm–5 h group (744.1 ± 61.2 MPa), which was attributed to phase-transformation toughening. The lowest values were observed in the case of the 5 Y-PSZ-1.5 mm–5 h (338.3 ± 34.8 MPa) group.ConclusionsBoth material type and thickness significantly affect the flexural strength of zirconia ceramics, whereas aging time does not; thus, material selection and thickness are crucial considerations for clinicians.

Surface Modification of Feldspathic Ceramic Used for Minimally Invasive Restorations: Effect of Airborne Particle Type on the Surface Properties and Biaxial Flexural Strength.

This study aimed to evaluate the effect of airborne particle abrasion with different particles on the surface free energy, roughness, and biaxial flexural strength of a feldspathic ceramic by comparing it with hydrofluoric acid etching, the standard surface treatment, and polishing. Square-shaped feldspathic ceramic specimens (12 mm × 12 mm × 1.2 mm) were divided into subgroups as airborne particles abraded with alumina (AO3a, AO3b, AO25, AO50a, AO50b, AO90, AO110a, AO110b, AO120a, and AO120b), silica (SO50a, SO50b, SO100, and SO100/200), or nutshell granule (NS100/200), hydrofluoric acid etched, and polished (n = 12). Surface free energy (n = 5), roughness (n = 5), biaxial flexural strength (n = 12), and Weibull moduli (n = 12) were investigated. Data were evaluated with 1-way ANOVA and Tukey HSD tests, and possible correlations were investigated with Pearson's correlation (α = 0.05). SO100/200 mostly had lower surface free energy (p ≤ 0.011), and polishing and etching led to higher surface free energy than AO3a, AO3b, and AO120a (p ≤ 0.031). Polished, SO100, and SO50b specimens mostly had lower roughness and AO125 had the highest roughness (p ≤ 0.029). SO100/200 mostly had lower biaxial flexural strength (p ≤ 0.041), and etched specimens had higher biaxial flexural strength than AO120a, AO120b, and SO50b (p ≤ 0.043). AO3b had the highest (33.56) and AO120b had the lowest (11.8) Weibull modulus. There was a weak positive correlation between the surface free energy and the biaxial flexural strength (r = 0.267, p = 0.011). A larger particle size mostly resulted in higher roughness, which was also affected by the particle shape. Most of the test groups had similar biaxial flexural strength to that of the hydrofluoric acid-etched group. Therefore, for tested feldspathic ceramic, airborne particle abrasion with tested parameters may be a suitable alternative without causing any further damage.

Are we approaching the development of a novel calcium phosphate-based bioceramic dental material?

ObjectivesDevelop a sustainable bovine hydroxyapatite dental ceramic with the addition of titanium dioxide (TiO2) nanoparticles (5 % and 8 % by weight), analyzing the outcome of this addition to the microstructure, as well as its mechanical and chemical properties, in order to evaluate whether they satisfy the International Organization for Standardization (ISO) 6872:2015 for dental ceramics or not. MethodsDisks were obtained through uniaxial followed by isostatic pressing from bovine hydroxyapatite powder and TiO2 nanoparticles and sintered at 1300ºC for 2 h. Three experimental groups were developed (HA, HA+5 %TiO2 and HA+8 %TiO2) and subjected to X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), indentation fracture (IF), biaxial flexural strength (BFS) and chemical solubility test. ResultsXRD revealed, for HA group, the appearance of a peak corresponding to b-tricalcium phosphate (ß-TCP). For HA+ 5 %TiO2 and HA+ 8 %TiO2, the entire composition was converted into ß-TCP and calcium titanate (CaTiO3). The SEM images showed a dense ceramic matrix and a uniform distribution of another phase in groups with TiO2 nanoparticles. HA+ 5 %TiO2 (1.40 ± 0.18 MPa.m1/2) and HA+ 8 %TiO2 (1.32 ± 0.18 MPa.m1/2) showed significantly higher fracture toughness values than HA (0.67 ± 0.09 MPa.m1/2). HA showed significantly higher characteristic stress (295.8 MPa) in comparison to groups with 5 % (235.1 MPa) and 8 % (214.4 MPa) TiO2 nanoparticles. Differences were not observed between the Weibull modulus values. The solubility results indicated that all experimental ceramics were above the 2000 ug/cm2 limit set by the ISO 6872:2015. SignificanceThis study proposed the development and characterization of a new ceramic for dental prosthesis made from HA extracted from bovine bones, with the intention of reusing these solids waste and transforming them into a sustainable and low-cost material. Although the experimental calcium phosphate ceramic with additions of 5 % and 8 % of TiO2 achieved desirable mechanical properties, the chemical solubility values were very high.

Biaxial flexural strength of nanoglass and multiwalled carbon nanotubes reinforced 3D-printed denture base resins and their shear bond strength to 3D-printed and acrylic denture teeth

ObjectiveEvaluation of biaxial flexural strength (BFS) of nanoglass (NG) and multiwalled carbon nanotubes (MWCNTs) reinforced 3D-printed denture base resins and their shear bond strength (SBS) to 3D-printed and acrylic denture teeth. MethodsSilanized NG and MWCNTs were added to 3D-printed denture base resin to obtain four groups: Control, 0.25 wt% NG, 0.25 wt% MWCNTs, and a combination group with 0.25 wt% of both fillers. All specimens were tested before and after 600 cycles of thermal aging. BFS (n = 88) was tested using disk-shaped specimens (12 ×2 mm) centralized on an O ring in a universal testing machine. Weibull analysis was conducted to assess predictability of failure. SBS (n = 176) was tested for acrylic and 3D-printed denture teeth attached to bar-shaped specimens in a universal testing machine followed by failure mode analysis using stereomicroscope. Two and three-way ANOVA tests followed by Tukey post hoc test were conducted for BFS and SBS. Kruskal-Wallis test compared percent change among groups with subsequent Dunn post hoc test with Bonferroni correction (α = 0.05). ResultsBFS was affected significantly by filler content (P < 0.001) and thermal cycling (P < 0.001), with thermal cycling displaying the uppermost effect (Ƞp2 =0.551). A significant interaction between filler content, thermal cycling, and teeth type was displayed by SBS results (P < 0.001, F=10.340, Ƞp2 =0.162). The highest BFS values belonged to 0.25 % MWCNTs while the highest SBS to printed teeth was displayed by the combination. SignificanceThe combination group displayed higher BFS and SBS to printed teeth compared to control which allows 3D-printed materials to have a long-term clinical success.

Physicochemical characterization of experimental resin-based materials containing calcium orthophosphates or calcium silicate

ObjectiveTo evaluate experimental dimethacrylate-based materials containing calcium orthophosphates or calcium silicate particles in terms of their optical, mechanical and Ca2+ release behaviour. MethodsDicalcium phosphate dihydrate (DCPD), hydroxyapatite (HAp), beta-tricalcium phosphate (β-TCP) or calcium silicate (CaSi) particles were added to a photocurable BisGMA/TEGDMA resin (1:1 in mols) at a 30 vol% fraction. Materials containing silanized or non-silanized barium glass particles were used as controls. Degree of conversion (DC) at the top and base of 2-mm thick specimens was determined by ATR-FTIR spectroscopy (n = 5). Translucency parameter (TP) and transmittance (%T) were determined using a spectrophotometer (n = 3). Biaxial flexural strength (BFS) and flexural modulus (FM) were determined by biaxial flexural testing after 24 h storage in water (n = 10). Ca2+ release in water was determined during 28 days by inductively coupled plasma optical emission spectrometry (n = 3). Statistical analysis was performed using ANOVA/Tukey test (DC: two-way; TP, %T; BFS and FM: one-way; Ca2+ release: repeated measures two-way, α = 5 %). Results: CaSi and β-TCP particles drastically reduced DC at 2 mm, TP and %T (p < 0.001). Compared to both controls, all Ca2+-releasing materials presented lower BFS (p < 0.001) and only the material with DCPD showed significantly lower FM (p < 0.05). The material containing CaSi presented the highest Ca2+ release, while among materials formulated with calcium orthophosphates the use of DCPD resulted in the highest release (p < 0.001). SignificanceCaSi particles allowed the highest Ca2+ release. Notwithstanding, the use of DCPD resulted in a material with the best compromise between optical behaviour, DC, strength and Ca2+ release.

Preparation and Properties of High Sound-Absorbing Porous Ceramics Reinforced by In Situ Mullite Whisker from Construction Waste.

Porous sound absorption ceramic is one of the most promising materials for effectively eliminating noise pollution. However, its high production cost and low mechanical strength limit its practical applications. In this work, low-cost and in situ mullite whisker-reinforced porous sound-absorbing ceramics were prepared using recyclable construction waste and Al2O3 powder as the main raw materials, and AlF3 and CeO2 as the additives, respectively. The effects of CeO2 content, AlF3 content, and sintering temperature on the microstructure and properties of the porous ceramics were systematically investigated. The results showed that a small amount of CeO2 significantly promoted the growth of elongated mullite crystals in the resultant porous ceramics, decreased the growth temperature of the mullite whiskers, and significantly increased the biaxial flexural strength. When 2 wt.% CeO2 and 12 wt.% AlF3 were added to the system, mullite whiskers were successfully obtained at a sintering temperature of 1300 °C for 1 h, which exhibited excellent properties, including an open porosity of 56.4 ± 0.6%, an average pore size of 1.32-2.54 μm, a biaxial flexural strength of 23.7 ± 0.9 MPa, and a sound absorption coefficient of >0.8 at 800-4000 Hz.

An Approach to Improve Specimen Processing for the Flexural Strength Testing of Zirconia.

Measuring the flexural strength of restorative materials such as zirconia is crucial for providing proper indications for clinical applications and predicting performance. Great variations in specimen preparation for flexural strength measurements exist among laboratories. The aim was to evaluate how the processing method, surface treatment, and test method of the specimens affect the flexural strength of zirconia. Zirconia specimens (VITA YZ HT) (n = 270) were processed using CAD/CAM or were conventionally milled with three different surface treatments (machined, ground, polished) and were measured with three-point bending (non-chamfered/chamfered) or biaxial flexural strength test. Weibull statistics were conducted. The mean flexural strength values ranged from 612 MPa (conventional, machined, three-point bending non-chamfered) to 1143 MPa (CAD/CAM, polished, biaxial flexural strength). The highest reliability is achieved when specimens are prepared using thoroughly controllable processing with CAD/CAM and subsequently polished. Higher strength values are achieved with the biaxial flexural strength test method because the stress concentration in relation to the effective volume is smaller. Polishing reduces surface microcracks and therefore increases the strength values.

Effect of TiO2 and CaO Addition on the Crystallization and Flexural Strength of Novel Leucite Glass-Ceramics.

The aim of this study was to investigate the effects of TiO2/CaO addition on the crystallization and flexural strength of leucite glass-ceramics (GC). Synthesis of translucent and high strength GCs is important for the development of aesthetic and durable dental restorations. To achieve this, experimental aluminosilicate glasses (1-3 mol% TiO2 and CaO (B1, B2, B3)) were melted in a furnace to produce glasses. Glasses were ball milled, screened and heat treated via crystallization heat treatments, and characterized using XRD, differential scanning calorimetry, dilatometry, SEM and biaxial flexural strength (BFS). Increasing nucleation hold time (1-3 h) led to a reduction in crystallite number for B2 and B3 GC, and significant differences in leucite crystal size at differing nucleation holds within and across test groups (p < 0.05). A high area fraction of leucite crystals (55.1-60.8%) was found in the GC, with no matrix microcracking. Changes in the crystal morphology were found with higher TiO2/CaO addition. Mean BFS of the GC were 211.2-234.8 MPa, with significantly higher Weibull modulus (m = 18.9) for B3 GC. Novel glass compositions enriched with TiO2/CaO led to crystallization of leucite GC of high aspect ratio, with high BFS and reliability. The study's findings suggest a potential high performance translucent leucite GC for use in the construction of dental restorations.

Characterization of a hydrothermally aged experimental alumina-toughened zirconia composite

ObjectivesTo assess the effects of different aging protocols on chemical, physical, and mechanical properties of an experimental ATZ composite compared to a zirconia. MethodsDisc-shaped specimens were obtained through uniaxial pressing of commercial powders (Tosoh), ATZ comprised of 80%ZrO2/20%Al2O3 (TZ-3YS20AB) and 3Y-TZP (3Y-SBE). The specimens of each material were divided into different groups according to the aging protocol: immediate, autoclave aging and hydrothermal reactor aging. The aging protocols were performed at 134 ºC for 20 h at 2.2 bar. Crystalline evaluations were performed using X-Ray Diffraction. The nanoindentation tests measured the elastic modulus (Em) and hardness (H). Biaxial flexural strength was performed, and Weibull statistics were used to determine the characteristic strength and Weibull modulus. The probability of survival was also determined. The Em and H data were analyzed by one-way ANOVA and Tukey test. ResultsDiffractograms revealed the presence of monoclinic phase in both materials after aging. The hydrothermal reactor decreased the Em for ATZ compared to its immediate condition; and the H for both ATZ and 3Y-TZP regarding their immediate and autoclave aging conditions, respectively. The aging protocols significantly increased the characteristic strength for ATZ, while decreased for 3Y-TZP. No difference regarding Weibull modulus was observed, except for 3Y-TZP aged in reactor. For missions of up to 500 MPa, both materials presented a high probability of survival (>99 %) irrespective of aging condition. SignificanceThe synthesized ATZ composite exhibited greater physical and microstructural stability compared to 3Y-TZP, supporting potential application of the experimental material for long-span reconstructive applications.

Effect of Grinding and Polishing Protocols on Surface Roughness, Flexural Strength, and Phase Transformation of High-Translucent 5 mol% Yttria-Partially Stabilized Zirconia

Abstract Objectives This study evaluated surface roughness, biaxial flexural strength, and phase transformation of 5Y-PSZ after grinding and polishing with different protocols. Material and Methods Two commercial 5Y-PSZ, Lava Esthetic (L) and Cercon xt (C), were used and divided into 3 groups: LC and CC represented unpolished control groups; LE and CE were polished with protocol I (EVE DIASYNT® PLUS HP following with EVE DIACERA RA); and LJ and CJ were polished with protocol II (Superfine diamond bur following with Jota ZIR Gloss polishing kit). Surface roughness was evaluated after polishing step-by-step with a contact-type profilometer. After high-gross polishing, the specimens were subjected to biaxial flexural strength test, crystallographic microstructure analysis using an X-ray diffractometer (XRD), and surface micro-topography using scanning electron microscopy (SEM). Statistical Analysis Surface roughness differences after each step and biaxial flexural strength between groups were evaluated with one-way ANOVA, followed by Bonferroni post-hoc analysis. Changes in surface roughness across four different time points within groups were assessed using one-way repeated measures ANOVA, followed by Bonferroni post-hoc analysis. Results After high-gross polishing, both polishing protocols showed significantly lower surface roughness than the grinding group (p &lt; 0.05). The LE and CE groups exhibited the highest surface roughness values, which were significant differences from the LJ and CJ groups (p &lt; 0.05). The LE group showed significantly lower biaxial flexural strength compared to the LC group (p &lt; 0.05). However, there was no statistically significant difference in the CE and CJ groups compared to the control group (p &gt; 0.05). Furthermore, all polishing protocols did not change the phase transformation of zirconia. Conclusion Polishing protocol II provided a smoother surface than the protocol I after high-gross polishing, while the biaxial flexural strength of materials remained unaffected.

Investigation on the Biaxial Flexural Strength of Universal Shade Resin-Based Composites.

The biaxial flexural strength of universal shade and conventional dental resin-based composites before and after alkaline degradation was investigated. Disk samples were prepared from these resin-based composites, and some of the specimens were immersed in 0.1 M NaOH solution to create deteriorated samples. The biaxial flexural strength of the samples before and after the alkaline degradation test was measured and statistically tested. The fracture surfaces after the biaxial flexural test were observed using a scanning electron microscope. The results showed that the biaxial flexural strength of the paste-type universal shade resin-based composite before alkaline degradation was significantly (19%) higher than that of the conventional type, but no difference was observed between the materials after alkaline degradation. On the other hand, the biaxial flexural strength of the flowable universal shade resin-based composites was significantly (around 35%) lower than that of the conventional composite, with or without degradation. Although, for paste-type materials, the biaxial flexural strength of universal shade resin-based composites was higher than that of conventional resin-based composites before alkaline degradation, after degradation the two materials showed similar values. For flowable materials, the biaxial flexural strength of universal shade resin-based composites was lower than that of conventional resin-based composites regardless of the presence or absence of degradation processes. These results suggest that some caution should be used when deciding whether to use flowable universal shade resin-based composite to fill a cavity.

Brittle-Ductile Threshold in Lithium Disilicate under Sharp Sliding Contact.

Computer-aided design (CAD)/computer-aided manufacturing (CAM) milling and handpiece grinding are critical procedures in the fabrication and adjustment of ceramic dental restorations. However, due to the formation of microfractures, these procedures are detrimental to the strength of ceramics. This study analyzes the damage associated with current brittle-regime grinding and presents a potential remedy in the application of a safer yet still efficient grinding regime known as "ductile-regime grinding." Disc-shaped specimens of a lithium disilicate glass-ceramic material (IPS e.max CAD) were obtained by cutting and crystallizing the lithium metasilicate CAD/CAM blanks (the so-called blue blocks) following the manufacturer's instructions. The discs were then polished to a 1 µm diamond suspension finish. Single-particle micro-scratch tests (n = 10) with a conical diamond indenter were conducted to reproduce basic modes of deformation and fracture. Key parameters such as coefficient of friction and penetration depth were recorded as a function of scratch load. Further, biaxial flexure strength tests (n = 6) were performed after applying various scratch loads to analyze their effects on ceramic strength. Scanning electron microscopy (SEM) and focused ion beam (FIB) were used to characterize surface and subsurface damage. Statistical analysis was performed using one-way analysis of variance and Tukey tests. While the SEM surface analysis of scratch tracks revealed the occurrence of both ductile and brittle removal modes, it failed to accurately determine the threshold load for the brittle-ductile transition. The threshold load for brittle-ductile transition was determined to be 70 mN based on FIB subsurface damage analyses in conjunction with strength degradation studies. Below 70 mN, the specimens exhibited neither strength degradation nor the formation of subsurface cracks. Determination of the brittle-ductile thresholds is significant because it sets a foundation for future research on the feasibility of implementing ductile-regime milling/grinding protocols for fabricating damage-free ceramic dental restorations.

Effect of multiple firings on optical and mechanical properties of Virgilite-containing lithium disilicate glass-ceramic of varying thickness

ObjectivesTo investigate the effect of multiple firings on color, translucency, and biaxial flexure strength of Virgilite-containing (Li0.5Al0.5Si2.5O6) lithium disilicate glass ceramics of varying thickness.Materials and methodsSixty discs were prepared from Virgilite-containing lithium disilicate blocks. Discs were divided according to thickness (n = 30) into T0.5 (0.5 mm) and T1.0 (1.0 mm). Each thickness was divided according to the number of firing cycles (n = 10); F1 (Control group): 1 firing cycle; F3: 3 firing cycles, and F5: 5 firing cycles. The discs were tested for color change (ΔE00) and translucency (TP00) using a spectrophotometer. Then, all samples were subjected to biaxial flexure strength testing using a universal testing machine. Data were collected and statistically analyzed (α = 0.5). For chemical analysis, six additional T0.5 discs (2 for each firing cycle) were prepared; for each firing cycle one disc was subjected to X-ray diffraction analysis (XRD) and another disc was subjected to Energy dispersive X-ray spectroscopy (EDX) and Scanning electron microscope (SEM).ResultsRepeated firing significantly reduced the translucency of F3 and F5 compared to F1 in T0.5 (p < 0.001), while for T1.0 only F5 showed a significant decrease in TP00 (p < 0.001). For ΔE00, a significant increase was recorded with repeated firings (p < 0.05) while a significant decrease resulted in the biaxial flexure strength regardless of thickness.ConclusionsRepeated firings had a negative effect on both the optical and mechanical properties of the Virgilite-containing lithium disilicate glass ceramics.Clinical relevanceRepeated firings should be avoided with Virgilite-containing lithium disilicate ceramics to decrease fracture liability and preserve restoration esthetics.