Storage Ring Beam Research Articles

Stability of C59 Knockout Fragments from Femtoseconds to Infinity

We have studied the stability of C59 anions as a function of time, from their formation on femtosecond timescales to their stabilization on second timescales and beyond, using a combination of theory and experiments. The C59− fragments were produced in collisions between C60 fullerene anions and neutral helium gas at a velocity of 90 km s−1 (corresponding to a collision energy of 166 eV in the center-of-mass frame). The fragments were then stored in a cryogenic ion beam storage ring at the DESIREE facility, where they were followed for up to 1 minute. Classical molecular dynamics simulations were used to determine the reaction cross section and the excitation energy distributions of the products formed in these collisions. We find that about 15% of the C59− ions initially stored in the ring are intact after about 100 ms and that this population then remains intact indefinitely. This means that C60 fullerenes exposed to energetic atoms and ions, such as stellar winds and shock waves, will produce stable, highly reactive products, like C59, that are fed into interstellar chemical reaction networks.

A high-intensity, low-energy heavy ion source for a neutron target proof-of-principle experiment at LANSCE

The capability to directly study neutron capture reactions on radionuclides with half-lives on the of order minutes would allow key cross section measurements in nuclear astrophysics and energy applications. However, such experiments with stationary targets are currently impossible because of signal detection and target sample fielding issues. To overcome these challenges, a neutron target facility is being developed to permit neutron capture experiments on unstable isotopes in inverse kinematics at the Los Alamos Neutron Science Center (LANSCE). This next-generation facility will consist of a heavily moderated, high-intensity spallation neutron target coupled with a radioactive ion beam storage ring. A proof-of-principle experiment is underway to demonstrate this neutron target concept at LANSCE in the near term with stable ions and without a storage ring. Here, mA-level beams of 10-50 keV heavy ions exhibiting large resonant neutron capture cross sections will be generated by a new ion source, transported through a large-volume neutron moderator surrounding an adjacent spallation target driven by the LANSCE accelerator, and collected downstream of the moderator for subsequent decay-counting measurements. The neutron density within the moderator will be obtained from these decay yields and compared with Monte Carlo N-Particle (MCNP) simulation results. The science application, operational requirements, and performance objectives for this heavy ion source will be presented.

Canadian Light Source beam position visualization tool

The Canadian Light Source orbit correction system acquires, collates, and publishes storage ring beam centroid position information from 48 beam position monitors (BPMs) at a rate of 1000 samples per second. We present a ”Beam Position Visualization Tool” that computes and displays dynamic Fast Fourier Transforms (FFTs) and Cumulative Power Spectral Densities (CPSDs) for all BPMs in real-time using full resolution data. The computed FFTs and CPSDs can be plotted in various combinations and in waterfall plots that allow visualization of changes over long periods of time. In addition, correlations between all BPM channel combinations are computed and ranked. Data from any two BPM channels can be selected for plotting in two dimensions wherein correlations are visually apparent. Computed CPSDs are further binned and archived for further analysis. Preliminary results from the Beam Position Visualization Tool have proven useful in identifying storage ring beam position noise at the Canadian Light Source.

The Münster cluster-jet target for the future P̅ANDA experiment

For high precision storage ring experiments as the future P̅ANDA experiment, very sophisticated internal targets have to be used. For this purpose, a state-of-the-art cluster-jet target was developed at the University Münster. Basically, hydrogen is cooled to cryogenic temperatures and pressed through a specially shaped Laval nozzle to form a cluster-jet expanding into vacuum. Due to the stability and large mass of the clusters, a practically undisturbed flight path in vacuum of above 5 m is possible, leading to manifold possible applications, including the interaction with a storage ring beam at a distance of 2.25 m as desired for the P̅ANDA experiment. With a first prototype target, the “proof-of-principle” was delivered, and after first improvements the world record in target thickness in such large distance to the nozzle was measured. Based on this work, the final P̅ANDA cluster-jet target was developed and built up, and is presented in this article.

BEM-Based Magnetic Field Reconstruction by Ensemble Kálmán Filtering

Abstract Magnetic fields generated by normal or superconducting electromagnets are used to guide and focus particle beams in storage rings, synchrotron light sources, mass spectrometers, and beamlines for radiotherapy. The accurate determination of the magnetic field by measurement is critical for the prediction of the particle beam trajectory and hence the design of the accelerator complex. In this context, state-of-the-art numerical field computation makes use of boundary-element methods (BEM) to express the magnetic field. This enables the accurate computation of higher-order partial derivatives and local expansions of magnetic potentials used in efficient numerical codes for particle tracking. In this paper, we present an approach to infer the boundary data of an indirect BEM formulation from magnetic field measurements by ensemble Kálmán filtering. In this way, measurement uncertainties can be propagated to the boundary data, magnetic field and potentials, and to the beam related quantities derived from particle tracking. We provide results obtained from real measurement data of a curved dipole magnet using a Hall probe mapper system.

Steady-state solutions of split beams in electron storage rings

Recently, a novel operation method for synchrotron light sources with transversely split beams has been explored to fulfill the rising demand for flexible and high-throughput X-ray sources required in such diverse fields as time-resolved X-ray spectroscopy, molecular chemistry in organic cells, high-resolution medical imaging, quantum materials science or sustainable energy research. Within that novel operation mode, additional stable regions are produced in the horizontal phase space by operating an electron storage ring on a resonance that is driven by the nonlinear sextupole or octupole magnets. In the longitudinal phase space, a similar split can be produced by introducing an oscillation of the synchrotron phase via a modulation of the phase of the radiofrequency resonator. Strong radiation damping in electron storage rings, however, has to be overcome before additional regions in phase space can become populated by particles and form stable islands. This damping mechanism changes the dynamics of the system and causes diffusion between the different islands in phase space, raising the question what kind of equilibrium state exists in the asymptotic temporal limit. In this paper, a finite-differences approximation in rotating action-angle coordinates is used to solve the Vlasov–Fokker–Planck equation and to study the obtained equilibrium states for the longitudinal as well as the transverse case. The number of solution vectors and the magnitude of the corresponding singular values of the matrix of the underlying finite-differences equation are used as abstract indicators to define the required parameter set that provides stable additional beamlets. As a consequence, the beamlets have a stability that is close to that of the main beam in terms of diffusion caused by the radiation damping and quantum excitation.

Novel perturbation method for judging the stability of the equilibrium solution in the presence of passive harmonic cavities

When using the harmonic cavity to stretch the beam in electron storage rings, we expect the beam can be lengthened effectively and also stably. Semianalytical approaches can be used to obtain the equilibrium distribution but generally failed in the prediction of its stability. In this work, a novel perturbation method is proposed to check whether the calculated equilibrium solution can survive from the $l=1$ mode perturbation. For the case of uniform beam filling, we derive a simple formula that can determine the threshold of $l=1$ mode instability under specific parameters, which is well verified with tracking simulation for the Hefei Advanced Light Facility storage ring.

Radiative cooling rates of substituted PAH ions.

The unimolecular dissociation and infrared radiative cooling rates of cationic 1-hydroxypyrene (OHPyr+, C16H10O+) and 1-bromopyrene (BrPyr+, C16H9Br+) are measured using a cryogenic electrostatic ion beam storage ring. A novel numerical approach is developed to analyze the time dependence of the dissociation rate and to determine the absolute scaling of the radiative cooling rate coefficient. The model results show that radiative cooling competes with dissociation below the critical total vibrational energies Ec = 5.39(1)eV for OHPyr+ and 5.90(1) eV for BrPyr+. These critical energies and implications for radiative cooling dynamics are important for astrochemical models concerned with energy dissipation and molecular lifecycles. The methods presented extend the utility of storage ring experiments on astrophysically relevant ions.

Designing linear lattices for round beam in electron storage rings using the solution by linear matrices analysis

For some synchrotron light source beamline applications, a round beam is preferable to a flat one. A conventional method of obtaining round beam in an electron storage ring is to shift its tune close to a linear difference resonance. The linearly coupled beam dynamics is analyzed with perturbation theories, which have certain limitations. In this paper, we adopt the Solution by LInear Matrices (SLIM) analysis to calculate exact beam sizes to design round beam lattices. The SLIM analysis can deal with a generally linearly coupled accelerator lattice. The effects of various coupling sources on beam emittances and sizes can be studied within a self-consistent frame. Both the on- and off-resonance schemes to obtain round beams are explained with examples. The SLIM formalism for two widely used magnet models: combined-function bending magnets, and planar wigglers and undulators, is also derived.

Storage Ring Design and Beam Instabilities Investigation for MEPhI’s Photon Source

Storage Ring Design and Beam Instabilities Investigation for MEPhI’s Photon Source

Application Driven Optimization of Cryogenic Current Comparators (CCC) for Beam Storage Rings

Non-destructive measurements of nA beam currents in particle beam storage rings by detecting the azimuthal magnetic field generated by moving charged particles with a Cryogenic Current Comparator (CCC) are well established. The detection of beam currents with small amplitudes with a CCC in a storage ring demands a high slew rate which is caused by the rapid change of the beam current exceeding the operational limit of the SQUID in flux-locked loop mode. Previous solutions to increase the slew rate used a LCR first-order low-pass filter were a small resistor, unfortunately, dominated the current noise of the CCC. In this work we present a novel take by adding a second resonator into the CCC which in turn allows for higher resistances of the LCR low-pass filter and therefore lower thermal current noise. A second challenge connected with this CCC approach is the residual magnetization of the highly permeable magnetic core and the resulting shielding currents in the superconducting circuits of the CCC. The timing of a storage ring in the range of minutes opens a way to reduce these DC currents using a LR high-pass filter. Using serial sub-micro ohm resistors, time constants in the hour range can be achieved to improve the stability and performance of the CCC system.

Polarization-dependent disappearance of a resonance signal: Indication for optical pumping in a storage ring?

We report on laser spectroscopic measurements on ${\mathrm{Li}}^{+}$ ions in the experimental storage ring ESR at the GSI Helmholtz Centre for Heavy Ion Research. Driving the $2s\text{ }{^{3}S}_{1}(F=3/2)\ensuremath{\leftrightarrow}2p\text{ }{^{3}P}_{2}(F=5/2)\ensuremath{\leftrightarrow}2s\text{ }{^{3}S}_{1}(F=5/2)$ $\mathrm{\ensuremath{\Lambda}}$-transition in $^{7}{\mathrm{Li}}^{+}$ with two superimposed laser beams it was found that the use of circularly polarized light leads to a disappearance of the resonance structure in the fluorescence signal. This can be explained by optical pumping into a dark state of polarized ions. We present a detailed theoretical analysis of this process that supports the interpretation of optical pumping and demonstrates that the polarization induced by the laser light must then be at least partially maintained during the round trip of the ions in the storage ring. Such polarized ion beams in storage rings will provide opportunities for new experiments, especially on parity violation.

Unimolecular fragmentation and radiative cooling of isolated PAH ions: A quantitative study.

Time-resolved spontaneous and laser-induced unimolecular fragmentation of perylene cations (C20H12 +) has been measured on timescales up to 2 s in a cryogenic electrostatic ion beam storage ring. We elaborate a quantitative model, which includes fragmentation in competition with radiative cooling via both vibrational and electronic (recurrent fluorescence) de-excitation. Excellent agreement with experimental results is found when sequential fragmentation of daughter ions co-stored with the parent perylene ions is included in the model. Based on the comparison of the model to experiment, we constrain the oscillator strength of the D1 → D0 emissive electronic transition in perylene (fRF = 0.055 ± 0.011), as well as the absolute absorption cross section of the D5 ← D0 excitation transition (σabs > 670 Mb). The former transition is responsible for the laser-induced and recurrent fluorescence of perylene, and the latter is the most prominent in the absorption spectrum. The vibrational cooling rate is found to be consistent with the simple harmonic cascade approximation. Quantitative experimental benchmarks of unimolecular processes in polycyclic aromatic hydrocarbon ions like perylene are important for refining astrochemical models.

Influence of electron cooling on the polarization lifetime of a horizontally polarized storage ring beam

A previous publication has shown that the in-plane polarization (IPP) component of a polarized 0.97-GeV/c deuteron beam in the COSY storage ring may acquire a polarization half-life in excess of 1000 s through a combination of beam bunching, electron cooling (prior to any spin manipulation), sextupole field adjustment, and a limitation of the beam intensity. This paper documents further tests pointing to additional gains in the IPP lifetime if cooling is active throughout the beam store.

Current Status and Planned Upgrades of the VEPP-5 Injection Complex

The VEPP-5 injection complex, consisting of two linacs and a damping storage ring, delivers electron and positron beams to the VEPP-4M and VEPP-2000 colliders operating at BINP. Over three years of injector operation, its efficiency has significantly increased and the maximum positron-storage rate has reached 1.2 × 1010 s–1. This progress was reached through tuning the constituent machines, upgrading the accelerator technology, and deploying a new 11-MHz station of RF cavities. By the start of the next running season, a new electron gun with a significantly increased maximum current and cathode lifetime will be installed.

Reevaluation of spin-orbit dynamics of polarized e+e− beams in high energy circular accelerators and storage rings: An approach based on a Bloch equation

We give an overview of our current/future analytical and numerical work on the spin polarization in high-energy electron storage rings. Our goal is to study the possibility of polarization for the CEPC and FCC-ee. Our work is based on the so-called Bloch equation for the polarization density introduced by Derbenev and Kondratenko in 1975. We also give an outline of the standard approach, the latter being based on the Derbenev–Kondratenko formulas.

Computation and consequences of high order amplitude- and parameter-dependent tune shifts in storage rings for high precision measurements

Nonlinear effects of the various electric field and magnetic field components of storage rings to confine the particles and bend their trajectory can cause substantial amplitude-dependent tune shifts within the beam. Furthermore, tune shifts are often sensitive to variations of system parameters, e.g. total particle momentum offsets [Formula: see text]. Such amplitude- and parameter-dependent tune shifts influence the dynamics and stability of a beam in particle storage rings. Thus, it is critical for high precision measurements to analyze and understand these influences. On this basis, we present normal form methods for the calculation of high order amplitude and system parameter dependencies of the horizontal and vertical tunes in storage rings using the differential algebra (DA) framework within COSY INFINITY. A storage ring is simulated using COSY INFINITY to generate a DA Poincaré return map describing the transverse phase space behavior after each revolution in the storage ring. The map is expanded around the parameter-dependent closed orbit of the system before transforming the resulting map into normal form coordinates to extract the high order tune dependencies on the phase space amplitude and variation in the system parameters. As a specific example, a storage ring similar to the Storage Ring of the Muon [Formula: see text]-2 Experiment at Fermilab (E989) is investigated.

Utilizing the high shunt impedance TM020-mode cavity in the double RF systems for the storage ring of the Thailand new light source

The utilization of the TM020-mode cavity for the storage ring based light source was pioneered by SPring-8 with its high quality factor and hence its high shunt impedance. KEK-LS has also studied the possibility of using this type of cavity for their storage ring. The TM020-mode cavity has larger transverse dimension compared to the traditional TM010-mode cavity, but with its higher shunt impedance it can be designed to fit in the new low emittance storage ring regardless. The new storage ring based light source project in Thailand aims to optimum the low emittance beam in nano-meters region with the energy of 3 GeV. The TM020-mode cavity was considered as the main cavity and the harmonic cavity for the storage ring. They have been designed to have their pipe aperture fits the storage ring beam ducts. The main cavity has a high shunt impedance of 8.3 MΩ with the 51,000 unloaded quality factor. The harmonic cavity has a high shunt impedance and an unloaded quality factor of 2.45 MΩ and 36,000, respectively. The damping mechanism of the parasitic modes and the tuning mechanism of the operating mode of these cavities were also studied. There will be four main cavities and six harmonic cavities in the new storage ring. Detailed design and study of these cavities will be presented.

Superconducting undulator coils with period length doubling

Only since few years it has been demonstrated experimentally that NbTi based superconducting undulators (SCUs) have a higher peak field on axis for the same gap and period length in operation with electron beam with respect to permanent magnet undulators (even the ones in vacuum and cooled to cryogenic temperatures). Another advantage of NbTi based SCUs with respect to permanent magnet devices is radiation hardness, widely demonstrated for NbTi magnets, which is and will become an increasingly important issue with the small gaps in the newest machines as round beam storage rings and FELs. Moreover, SCU technology allows switching of the period length by changing the current direction in one of separately powered subset of winding packages of the superconducting coils. This feature further broadens the energy range of the emitted photons, required by the different beamlines. To this end a 0.41 m long superconducting undulator coil with switchable period length between 17 mm and 34 mm has been developed. In this contribution we describe the design and report on the quench tests, as well as on the magnetic field measurementsThe first section in your paper.

The Signal Processing Electronics for the Beam Position Monitors of Russian Fourth Generation Synchrotron Radiation Source

The project of fourth-generation Ultimate Source for Synchrotron Radiation (USSR-4) is under development in Russia by leading of National Research Center “Kurchatov institute”. Some of diagnostic systems required for the new facility have to be developed or redeveloped to satisfy the features of the new facility. Hundreds beam position monitors (BPM) are installed along beam transfer lines, booster and storage rings to control the electron beam position. In booster and storage ring the electronics of BPM has to provide both the normally beam circulation and the first beam turn operation. It has to provide beam position monitoring in the bunch-by-bunch option for all operational modes [1]. In this manuscript we discuss the architecture of the BPM electronics, important aspects of the analog front-end, available components and a resulting performance of designed electronic module.