Beam Accelerator Research Articles

Direct Acceleration of an Electron Beam with a Radially Polarized Long-Wave Infrared Laser

Direct Acceleration of an Electron Beam with a Radially Polarized Long-Wave Infrared Laser

New operation analysis method for vacuum tube driving a tuned cavity

The rf system of China Spallation Neutron Source (CSNS) Rapid Cycling Synchrotron (RCS) utilizes vacuum tubes to drive the ferrite-loaded cavities. Ensuring stable tube operation in the rf system is crucial for the acceleration of high-intensity beams, as any instability may impede further increases in beam power. Therefore, the operation of the vacuum tube under heavy beam loading has attracted significant attention, particularly in the case of CSNS-II RCS, where the circulating beam current is expected to reach up to 15.25 A, imposing a substantial burden on the vacuum tube for beam loading compensation. Thus, a comprehensive analysis of tube operation is imperative. However, current methods for the tube operation analysis are developed based on wideband rf cavities, which are inadequate when the load of the tube is a narrowband ferrite-loaded cavity equipped with a tuning system. The presence of a tuning system renders the modeling method for wideband rf cavities inapplicable for ferrite-loaded cavities. Therefore, the development of a new method is necessary. This paper introduces a novel method for analyzing operation of vacuum tube driving a tuned cavity. The effectiveness of the method is validated by comparing the analysis results with measurements under beam loading conditions. Furthermore, an estimation of tube operation under 500 kW beam loading for CSNS-II is provided. Published by the American Physical Society 2024

PE/PP fibrous adsorbents with bifunctional groups of tertiary amine and phosphate prepared by electron beam induced co-grafting for heavy metal adsorption of both cationic and anionic forms in acidic conditions.

A novel fabric adsorbent having bifunctional groups of tertiary amine and phosphate was prepared by co-graft polymerization of 2-diethylaminoethyl methacrylate (NMA) and 2-hydroxyethyl methacrylate phosphate (PMA) onto a polyethylene/polypropylene nonwoven fabric (PE/PP NF) under low-energy electron beam acceleration. The process involved pre-irradiating the fabric and immersing it in the comonomer solution for grafting. The kinetics of radiation-induced graft polymerization at a total dose of 100 kGy was investigated. For pre-irradiation at 100 kGy, the optimum condition offering highest degree of grafting was at 12 wt% of NMA, 8 wt% of PMA and 4 h of reaction time. The adsorption of anions using hydrogen chromate (HCrO4−) or Cr(VI) and cations using lead (Pb(II)), cadmium (Cd(II)) and copper (Cu(II)) in aqueous solution was carried out. The results demonstrated that the bifunctional adsorbent was able to adsorb both heavy metal anionic and cationic ions from water. The co-grafted adsorbents with tertiary amine and phosphate were able to adsorb 85% Cr(VI) anion and 29% Pb(II) cations from mixed Cr(VI) and Pb(II) solution at pH 3.0 and 71% Pb(II), 13% Cd(II) and 31 % Cu(II) from mixed Pb(II), Cd(II) and Cu(II) solution at pH 5.0. The unique achievement of this study is its hypothesis that a bifunctional adsorbent can be prepared from radiation-induced graft polymerization of two different monomers onto NF, along with proof that the prepared bifunctional adsorbent can actually absorb both cationic or anionic heavy metals forms. Additionally, the adsorbent's preparation offers a rapid and straightforward one-step grafting technique. Therefore, the new bifunctional adsorbents can remove heavy metal ions in aqueous solution, either in the cation or anion form, thus offering highly promising applications in industrial wastewater treatment.

Proton FLASH Irradiation Using a Synchrotron Accelerator: Differences by Irradiation Positions.

To establish an ultra-high dose rate (UHDR) radiation system using a synchrotron proton beam accelerator and to compare the effects by irradiation positions on cultured cells and chick embryos. Protons for UHDR were obtained by applying high-frequency power at much higher levels than usual to extract all protons within approximately 50 ms. Subsequently, monitoring with a Faraday cup was performed immediately after synchrotron extraction and the waveform was adjusted accordingly. Four cultured tumor lines, two normal cell lines, and chick embryos were used. Ultra-high dose-rate radiation (UHDR-RT) at 6-18 Gy (200-300 Gy/s, single exposure) and conventional dose-rate radiation (Conv-RT) at 6-18 Gy (3 Gy/s) were administered to the 1-cm spread-out Bragg peak (SOBP) and the plateau region preceding SOBP. Following irradiation, disparities in cell growth rates and cell cycle progression were assessed, and cell survival was evaluated via colony assay. Chick embryos were also examined for survival. UHDR-RT was achieved at a range of 40 to 800 Gy/s, encompassing both plateau and peak phases. In vitro studies demonstrated similar cell-killing effects between UHDR-RT and Conv-RT in cancer cells. Significant apoptotic effects and G2 arrest were observed during the cell cycle under peak UHDR-RT conditions. The FLASH effect was not observed in normal single cells under normal atmospheric conditions. Stronger cell-killing effects were noted in V79 spheroids exposed to peak UHDR-RT than peak Conv-RT. Moreover, in chick embryos, an increase in survival rate, indicative of the FLASH effect, was observed. The FLASH effect was also achieved with UHDR-RT using a synchrotron proton beam accelerator in chick embryos. The cell-killing effects in cancer cells were higher with peak UHDR-RT which may be due to the higher linear energy transfer at the SOBP.

High-count-rate particle tracking in proton and carbon radiotherapy with Timepix2 operated in ultra-short acquisition time

This work investigates the operational acquisition time limits of Timepix3 and Timepix2 detectors operated in frame mode for high-count rate of high deposited energy transfer particles. Measurements were performed using alpha particles from a 241Am laboratory source and proton and carbon ion beams from a synchrotron accelerator. The particle count rate upper limit is determined by overlapping per-pixel particle signals, identifiable by the hits per pixel counter > 2, indicating the need to decrease acquisition time. On the other hand, the lower limit is the time required to collect the particle deposited charge while maintaining spectral properties. Different acquisition times were evaluated for an AdvaPIX Timepix3 detector (500 μm Silicon sensor) with standard per-pixelDigital to Analog Converter (DAC)settings and a Minipix Timepix2 detector (300 μm Silicon sensor) with standard and customized settings the pulse shaping parameter and threshold. For AdvaPIX Timepix3, spectra remained accurate down to 100 μs frame acquisition time; at 10 μs, loss of collected charge occurred, suggesting either avoiding this acquisition time or applying a correction. Timepix2 allowed acquisition times down to 100 ns for single particle track measurements even for high energy loss, enabled by a new Timepix2 feature delaying shutter closure until full particle charge collection. This work represents the first measurement utilizing Timepix-chips pixel detectors in an accelerator beam of clinical energy and intensity without the need to decrease the beam current. This is made possible by exploiting the short shutter feature in Timepix2 and a customized per-pixel energy calibration of the Timepix2 detector with a larger discharging signal value which allowed for shorterTime-over-Threshold (ToT)signal. These customized settings extend the operation of the pixel detectors to higher event rates up to 109 particles/cm2/s.

Correction of dynamic magnetic field errors at the rapid cycling synchrotron of China Spallation Neutron Source

At a Rapid Cycling Synchrotron (RCS), dynamic magnetic field errors, such as magnetic field tracking errors and dynamic fringe field effects, can cause time-dependent tune shift during beam acceleration. If the tune shift is significant enough to pass through resonance lines, it can lead to emittance growth and beam losses. Correcting time-dependent tune shift during acceleration is crucial for a RCS. Modulating the exciting current and magnetic field of quadrupole magnets at a RCS, which are powered by resonant circuits, is challenging during the ramping process. Correcting time-dependent tune shift at a RCS poses a significant technical challenge. We have proposed a method for correcting time-dependent tune shift at the rapid cycling synchrotron of China Spallation Neutron Source (CSNS), based on waveform compensation at the quadrupole magnets. This approach involves modulating the magnetic field variation process by injecting time harmonic exciting current into the quadrupole magnets. This method has been validated during the CSNS beam commissioning and has been applied at the RCS of CSNS to correct various dynamic magnetic field errors.

Dynamic Modeling and Analysis of Multi-Span Timoshenko Beams Under Moving Loads

Dynamic response analysis of multi-span beams is one of the important topics in the field of highway and railway engineering, which provides valuable guidance for the design, operation and maintenance of multi-span bridges. It is worth considering how to calculate the dynamic characteristics of multi-span beams quickly and conveniently. In this study, an effective analytical method is developed for the dynamic modeling and investigations of multi-span Timoshenko beams under moving loads by employing the assumed mode method (AMM). Based on Hamilton’s principle, the equation of motion of the Timoshenko multi-span beam subjected to moving loads is formulated and the natural frequencies are calculated. A comprehensive investigation is conducted on the dynamic responses of the multi-span Timoshenko beam considering different factors, including the length-to-thickness ratio, disorder degree, arrangement order, number of spans and related parameters of moving loads. In addition, the influence of the interval and velocity of the moving load series on the dynamic responses, including displacement, velocity and acceleration of the multi-span beam, are analyzed in detail. The theoretical calculation results of multi-span Timoshenko beams under moving loads are compared with numerical results obtained from ANSYS software, and the results are in good agreement. This demonstrates that the developed method, which utilizes the AMM to analyze the dynamic characteristics of multi-span beams subjected to moving loads, significantly simplifies the calculations and is well-suited for practical engineering applications.

Real-time monitoring and protection strategies for dense granular flow spallation target in Accelerator-Driven System

An innovative concept of a high-power, gravity-driven, dense granular spallation target has been integrated into the prototype design of the China initiative Accelerator-Driven System (CiADS), which is envisioned as a promising nuclear demonstration facility aimed at converting long-lived fission products and minor actinides into short-lived isotopes. This spallation target system, bridging the proton beam accelerator and the subcritical reactor, plays a crucial role in ensuring safety control and facilitating dynamic operational strategies. In this study, we have developed a system design for an online detector array, incorporating several neutron fission chambers and thermocouples installed in the gap between the spallation target and the subcritical reactor to monitor operations. Furthermore, we have devised real-time monitoring and protection methods to tackle the challenges of measuring beam position and the blockage condition associated with granular flow, considering the distribution of neutron flux and heat deposition under abnormal irradiation conditions. Monte Carlo simulations have demonstrated the applicability and feasibility of the control system for the dense granular spallation target in the accelerator-driven system. The numerical results confirm that the proposed control system meets the requirements for stable measurement with acceptable accuracy.

Development of a high-yield compact D-D neutron generator

An improved high-yield compact D-D neutron generator has been developed for active neutron non-destructive interrogation at Lanzhou University in China. The generator has been meticulously designed based on the magnetic field distribution of the duoplasmatron ion source, the electric field distribution of the beam extraction acceleration system, beam transport, and target cooling system. The performance characteristics of the generator were measured under different deuterium beam energies and beam intensities. The experimental results indicated that the D-D neutron yield reached 1×109 n/s with the deuterium beam parameter of 210 keV/6.0 mA. The operational stability of the generator was assessed for 150 minutes, and the test results show that the generator has better stability in operation. This generator has potential applications in neutron radiography, active interrogation of special nuclear materials, and neutron activation analysis.

Engineering implementation of permanent magnet uniform spreading system for 3 MeV electron beam accelerator

Electron radiation technology, a significant application of non-power civil nuclear technology, opens up various research opportunities for electron beam accelerators as radiation sources. This paper introduces the engineering implementation of a permanent magnet uniform spreading system for the 3 MeV electron beam accelerator. The system is designed to improve radiation homogeneity, which is a crucial performance parameter in the radiation processing. The paper firstly investigates the collimation of magnets and beam spot in electron beam accelerators and proposes a novel collimation method. In addition, we also address various engineering implementation challenges encountered during the practical application of the uniform spreading system's permanent magnet devices. As a prerequisite for the application of uniform spreading system, a long-term stability experiment is conducted on the permanent magnets in radiation environments. The engineering feasibility of the uniform spreading system is ultimately verified by assessing the radiation homogeneity at the target using radiation dose tablets.

J-PARC linac and RCS – operational status and upgrade plan to 2 MW

The linac and the 3 GeV rapid-cycling synchrotron (RCS) at the Japan Proton Accelerator Research Complex (J-PARC) were designed to provide 1-MW proton beams to the following facilities. Due to the improvement of the accelerator system, we accelerated a 1-MW beam with a small beam loss. The lack of anode current in the radiofrequency (RF) cavity, rather than beam loss, limits the RCS beam power. Recently, we developed a new acceleration cavity that can accelerate a beam with a low anode current. This new cavity enables us to reduce the requirement for the anode power supply and accelerate a beam of more than 1 MW. We considered how to achieve beam acceleration beyond 1 MW. So far, a beam of up to 1.5 MW is expected to be accelerated after replacing the RF cavity. We also studied to achieve an up to 2 MW beam in J-PARC RCS.

IAEA fostering of the development and applications of nuclear analytical techniques for Heritage Science

The IAEA Physics Section is strongly involved in the development and utilization of accelerator-based analytical techniques, which are powerful tools for the characterization of cultural and natural heritage objects and materials. Various activities are carried out with the purpose to build capacity, strengthen capabilities, transfer knowledge and foster networking in the field of heritage science. In addition, access to different X-ray fluorescence spectrometers and other analytical techniques is provided at the Nuclear Science and Instrumentation Laboratory (part of the IAEA Physics Section), and access to ion beam accelerators and synchrotron light is facilitated thanks to collaborations with Ruđer Bošković Institute (RBI) in Croatia and the Elettra Sincrotrone facility in Italy, respectively. Member States are also supported on their Research and Development programmes, as well as through the technical cooperation projects. This paper aims to provide a broad overview about how the IAEA Physics Section is engaged in the field of heritage science, promoting the safe, reliable, and effective use of ion beam, X-ray and neutron-based techniques for the characterization and preservation of cultural and natural heritage through its global networks and partners.

Unforeseen advantage of looser focusing in vacuum laser acceleration

Acceleration of electrons in vacuum directly by intense laser fields holds great promise for the generation of high-charge, ultrashort, relativistic electron bunches. While the energy gain is expected to be higher with tighter focusing, this does not account for the reduced acceleration range, which is limited by diffraction. Here, we present the results of an experimental investigation that exposed nanotips to relativistic few-cycle laser pulses. We demonstrate the vacuum laser acceleration of electron beams with 100s pC charge and 15 MeV energy. Two different focusing geometries, with normalized vector potential a0 of 9.8 and 3.8, produced comparable overall charge and electron spectra, despite a factor of almost ten difference in peak intensity. Our results are in good agreement with 3D particle-in-cell simulations, which indicate the importance of dephasing.

Accelerating cavity fault prediction using deep learning at Jefferson Laboratory

Abstract Accelerating cavities are an integral part of the continuous electron beam accelerator facility (CEBAF) at Jefferson Laboratory. When any of the over 400 cavities in CEBAF experiences a fault, it disrupts beam delivery to experimental user halls. In this study, we propose the use of a deep learning model to predict slowly developing cavity faults. By utilizing pre-fault signals, we train a long short-term memory-convolutional neural network binary classifier to distinguish between radio-frequency (RF) signals during normal operation and RF signals indicative of impending faults. We optimize the model by adjusting the fault confidence threshold and implementing a multiple consecutive window criterion to identify fault events, ensuring a low false positive rate. Results obtained from analysis of a real dataset collected from the accelerating cavities simulating a deployed scenario demonstrate the model’s ability to identify normal signals with 99.99% accuracy and correctly predict 80% of slowly developing faults. Notably, these achievements were achieved in the context of a highly imbalanced dataset, and fault predictions were made several hundred milliseconds before the onset of the fault. Anticipating faults enables preemptive measures to improve operational efficiency by preventing or mitigating their occurrence.

Elevating electron energy gain and betatron x-ray emission in proton-driven wakefield acceleration

The long proton beams present at CERN have the potential to evolve into a train of microbunches through the self-modulation instability process. The resonant wakefield generated by a periodic train of proton microbunches can establish a high acceleration field within the plasma, facilitating electron acceleration. This paper investigates the impact of plasma density on resonant wakefield excitation, thus influencing the acceleration of a witness electron bunch and its corresponding betatron radiation within the wakefield. Various scenarios involving different plasma densities are explored through particle-in-cell simulations. The peak wakefield in each scenario is calculated by considering a long pre-modulated proton driver with a fixed peak current. Subsequently, the study delves into the witness beam acceleration in the peak wakefield and its radiation emission. Elevated plasma density increases both the number of microbunches and the accelerating gradient of each microbunch, consequently resulting in heightened resonant wakefield. Nevertheless, the scaling is disrupted by the saturation of the resonant wakefield due to the nonlinearities. The simulation results reveal that at high plasma densities, an intense and broadband radiation spectrum extending into the domain of the hard x-rays and gamma rays is generated. Furthermore, in such instances, the energy gain of the witness beam is significantly enhanced. The impact of wakefield on the witness energy gain and the corresponding radiation spectrum is clearly evident at elevated densities.

Erratum: Acceleration of uranium beam to record power of 10.4 kW and observation of new isotopes at Facility for Rare Isotope Beams [Phys. Rev. Accel. beams 27 , 060101 (2024)

Erratum: Acceleration of uranium beam to record power of 10.4 kW and observation of new isotopes at Facility for Rare Isotope Beams [Phys. Rev. Accel. beams <b>27</b> , 060101 (2024)

Analysis of plasma wakefield generation by a Laguerre-Gaussian laser beam in laser-plasma accelerators with external injection

This study presents a comprehensive modeling of wakefield generation through external injection utilizing a Laguerre–Gaussian (LG) laser beam in a bubble/blowout regime. The wakefield dynamics are simulated in two dimensions using the particle-in-cell (2D-PIC) method via Wake-T tool, aiming to investigate the underlying mechanisms and characteristics of this process. The simulation results provide insights into the behavior of electrons within the wakefield, their acceleration, phase spaces of the electron beam, velocity distribution, and longitudinal and transversal profiles of the laser electric field in the plasma. The presented model serves as a valuable tool for further investigations into wakefield generation with external injection using LG laser beams, facilitating advancements in this field of study.

Conditional guided generative diffusion for particle accelerator beam diagnostics

Advanced accelerator-based light sources such as free electron lasers (FEL) accelerate highly relativistic electron beams to generate incredibly short (10s of femtoseconds) coherent flashes of light for dynamic imaging, whose brightness exceeds that of traditional synchrotron-based light sources by orders of magnitude. FEL operation requires precise control of the shape and energy of the extremely short electron bunches whose characteristics directly translate into the properties of the produced light. Control of short intense beams is difficult due to beam characteristics drifting with time and complex collective effects such as space charge and coherent synchrotron radiation. Detailed diagnostics of beam properties are therefore essential for precise beam control. Such measurements typically rely on a destructive approach based on a combination of a transverse deflecting resonant cavity followed by a dipole magnet in order to measure a beam’s 2D time vs energy longitudinal phase-space distribution. In this paper, we develop a non-invasive virtual diagnostic of an electron beam’s longitudinal phase space at megapixel resolution (1024 × 1024) based on a generative conditional diffusion model. We demonstrate the model’s generative ability on experimental data from the European X-ray FEL.

The Continuous Electron Beam Accelerator Facility at 12 GeV

This review paper describes the energy-upgraded Continuous Electron Beam Accelerator Facility (CEBAF) accelerator. This superconducting linac has achieved 12 GeV beam energy by adding 11 new high-performance cryomodules containing 88 superconducting cavities that have operated cw at an average accelerating gradient of 20 MV/m. After reviewing the attributes and performance of the previous 6 GeV CEBAF accelerator, we discuss the upgraded CEBAF accelerator system in detail with particular attention paid to the new beam acceleration systems. In addition to doubling the acceleration in each linac, the upgrade included improving the beam recirculation magnets, adding more helium cooling capacity to allow the newly installed modules to run cold, adding a new experimental hall, and improving numerous other accelerator components. We review several of the techniques deployed to operate and analyze the accelerator performance and document system operating experience and performance. In the final portion of the document, we present much of the current planning regarding projects to improve accelerator performance and enhance operating margins, and our plans for ensuring CEBAF operates reliably into the future. For the benefit of potential users of CEBAF, the performance and quality measures for the beam delivered to each of the experimental halls are summarized in the Appendix. Published by the American Physical Society 2024

Bayesian optimization algorithms for accelerator physics

Accelerator physics relies on numerical algorithms to solve optimization problems in online accelerator control and tasks such as experimental design and model calibration in simulations. The effectiveness of optimization algorithms in discovering ideal solutions for complex challenges with limited resources often determines the problem complexity these methods can address. The accelerator physics community has recognized the advantages of Bayesian optimization algorithms, which leverage statistical surrogate models of objective functions to effectively address complex optimization challenges, especially in the presence of noise during accelerator operation and in resource-intensive physics simulations. In this review article, we offer a conceptual overview of applying Bayesian optimization techniques toward solving optimization problems in accelerator physics. We begin by providing a straightforward explanation of the essential components that make up Bayesian optimization techniques. We then give an overview of current and previous work applying and modifying these techniques to solve accelerator physics challenges. Finally, we explore practical implementation strategies for Bayesian optimization algorithms to maximize their performance, enabling users to effectively address complex optimization challenges in real-time beam control and accelerator design. Published by the American Physical Society 2024