Formation Of Bands Research Articles

Investigation of the Shear Mechanism at Sand-Concrete Interface under the Influence of the Concave Groove Angle of the Contact Surface

A “random-type” sand–concrete interface shear test was developed based on the sand cone method, with a focus on the most commonly encountered triangular contact surface morphology. A “regular-type” triangular interface, matched in roughness to the “random-type”, was meticulously designed. This “regular-type” interface features five distinct triangular groove inclinations: 18°, 33°, 50°, 70°, and 90°. A series of sand–concrete interface direct shear tests were conducted under consistent compaction conditions to investigate the impact of varying compaction densities and triangular groove inclinations on the shear strength at the interface. Particle flow simulations were utilized to examine the morphology of the shear band and the characteristics of particle migration influenced by the triangular contact surface. This analysis is aimed at elucidating the influence of the inclination of the triangular groove on the shear failure mechanism at the sand–concrete interface. The findings indicate that: (1) The morphology of the interface significantly impacts the shear strength of the sand–concrete interface, while the shape of the stress-displacement curve experiences minimal alteration. (2) At smaller inclination angles, particle contact forces are arranged in a wave-like configuration around the sawtooth tip, resulting in a non-uniform stress distribution along the sawtooth slope. However, as the inclination angle grows, the stress concentration at the sawtooth tip diminishes, and the stress distribution across the sawtooth slope becomes more consistent. (3) Particle migration is significantly influenced by the sawtooth’s inclination angle. At lower angles, particles climb the structure’s tip through sliding and rolling. As the angle increases, particle motion shifts to shear, accompanied by a transition in friction from surface friction to internal shear friction. This leads to the formation of a wider shear band and an increase in shear strength.

Changes in Metabolism and Content of Chlorophyll in Common Duckweed (Lemna minor L.) Caused by Environmental Contamination with Fluorides.

The impact of fluorine on plants remains poorly understood. We examined duckweed growth in extracts of soil contaminated with fluorine leached from chicken manure. Additionally, fluorine levels were analyzed in fresh manure, outdoor-stored manure, and soil samples at varying distances from the manure pile. Fresh manure contained 37-48 mg F- × kg-1, while soil extracts contained 2.1 to 4.9 mg F- × kg-1. We evaluated the physiological effects of fluorine on duckweed cultured on soil extracts or in 50% Murashige-Skoog (MS) medium supplemented with fluorine concentrations matching those in soil samples (2.1 to 4.9 mg F- × L-1), as well as at 0, 4, and 210 mg × L-1. Duckweed exposed to fluorine displayed similar toxicity symptoms whether in soil extracts or supplemented medium. Fluoride at concentrations of 2.1 to 4.9 mg F- × L-1 reduced the intact chlorophyll content, binding the porphyrin ring at position 32 without affecting Mg2+. This reaction resulted in chlorophyll a absorption peak shifted towards shorter wavelengths and formation of a new band of the F--chlorophyll a complex at λ = 421 nm. Moreover, plants exposed to low concentrations of fluorine exhibited increased activities of aminolevulinic acid dehydratase and chlorophyllase, whereas the activities of both enzymes sharply declined when the fluoride concentration exceeded 4.9 mg × L-1. Consequently, fluorine damages chlorophyll a, disrupts the activity of chlorophyll-metabolizing enzymes, and diminishes the plant growth rate, even when the effects of these disruptions are too subtle to be discerned by the naked human eye.

Channel power management of 400 G transmission system based on C6T + L6 T spectrum and QPSK modulation format

In the 400 Gbit/s transmission system based on C + L band spectrum and QPSK modulation format, the short-wavelength signal power will be shifted to the long-wavelength signal due to the presence of the stimulated Raman scattering (SRS) effect, which will seriously affect the performance of the transmission system as the transmission span accumulates. The solution is to set the gain and gain slopes of the C-band amplifier and L-band amplifier appropriately at each optical amplifier site, and adjust the signal power of each channel through the WSS at the transmitting end and the WSS at the DGE site, so that the flatness of the channel power at the receiving end can be controlled in a reasonable range, thus guaranteeing the transmission performance of the system. However, the system fault will destroy the originally set channel power, which will seriously affect the transmission performance of the system. In this paper, filling channel device combined with output power locking of amplifiers used in a 400 Gbit/s system based on C + L band and QPSK modulation format to provide the protection for the system is proposed and demonstrated for the first time, which gives different solutions for sudden fault at different locations of the system, and provides a reference for the channel power management of multi-band optical transmission systems in the future.

Experimental Investigation of Parameters Influencing the Formation of Dry Bands and Related Electric Field

This paper presents an experimental investigation conducted to determine the influence of parameters such as the ambient temperature, pollution level, and substrate material on the formation of dry bands on polluted layers. To investigate these parameters, we applied a simplified insulator geometry, developed in our previous work, to experimentally control the complex process of dry band formation on a polluted surface. The simple geometry of the experimental model enabled the use of Plexiglas, RTV, and glass as construction substrate materials. RTV and glass were used to simulate a composite and ceramic insulator surface, respectively. Moreover, an electrooptic (EO) probe enabled the measurement of the axial E-field evolution at the surface of the dry band during dry band formation. The results indicated that the substrate material, ambient temperature, and pollution level substantially influence dry band formation. The effects of the first two parameters are directly associated with heat transfer phenomena in the substrate material and at the ambient air/substrate interface. The effect of the third parameter is associated with absorption and evaporation of the pollution layer. In addition, the appearance of the dry band can be clearly identified by a rapid increase in both the pollution layer resistance and the axial E-field in the dry band area. The value of the axial E-field is influenced primarily by the width of the dry band and by the pollution layer resistance, which is directly dependent on the humidification duration. Finally, because most of the results obtained herein were in accordance with those in the literature, we conclude that the proposed experimental model may provide an effective and inexpensive testing method for developing new materials and solutions for improving the dielectric performance of insulators used in polluted environments. Similarly, the simple geometry of the experimental model and the ability to easily control the experimental parameters may enable this tool to validate the results of various numerical models in studies of the thermoelectrical behavior of polluted insulators.

Comparison of the effect of Everolimus, Prednisolone, and a combination of both on experimentally induced peritoneal adhesions in rats

Postoperative intra-abdominal adhesions represent a significant post-surgical problem. Its complications can cause a considerable clinical and cost burden. Herein, our study aimed to investigate the effect of Everolimus on peritoneal adhesion formation after inducing adhesions in rats. In this experimental study, adhesion bands were induced by intraperitoneal injection of 3 ml of 10% sterile talc solution in 64 male albino rats. The first group served as the control group. The second one received oral Prednisolone (1 mg/kg/day), the third received Everolimus (0.1 mg/kg/day), and group four received both drugs with similar dosages for four consecutive weeks. The formation of adhesion bands was qualitatively graded according to the Nair classification. The rats in the control group had extensive adhesions between the abdominal wall and the organs. Regarding substantial adhesion formation, 50% (8/16) of animals in the control group had substantial adhesions, while this rate in the groups receiving Prednisolone, Everolimus, and combination treatment was 31%, 31%, and 31%, respectively. Also, 68.75% (5/11) of the Prednisolone recipients had insubstantial adhesions, the same as Everolimus recipients, while in the combination group, 66.66% (10/15) rats had insubstantial adhesions. Everolimus demonstrated satisfactory results in reducing the rates of induced peritoneal adhesion in an experimental model, similar to Prednisolone and superior to a combination regime.

Crystal plasticity modeling and analysis for the transition from intergranular to transgranular failure in nickel-based alloy Inconel 740H at elevated temperature

The precipitation-strengthened Nickel-based alloy Inconel® 740H® (IN740H) exhibits increased ductility at higher applied strain rates during quasi-static tensile tests at an elevated temperature of 760 °C. The examination of fracture surfaces in this context reveals a noteworthy transition of underlying fracture mechanisms from transgranular to intergranular fracture as the applied strain rate decreases from 1×10−3/s to 0.83×10−4/s. To thoroughly understand the mechanical response of IN740H under these conditions, this study develops a crystal plasticity finite element (CPFE) model. This model incorporates various deformation mechanisms including dislocation slips, climb, and grain boundary sliding, which are relevant to the test conditions. The model is calibrated using data from both tensile tests at different strain rates and creep tests across a broad stress range at 760 °C, enabling the accurate determination of model parameters for each mechanism. Simulation results well captured the experimental observations of different failure modes. At higher strain rates, the model shows a dominance of dislocation slip leading to heterogeneous plastic deformation and formation of transgranular shear bands causing the failure, while at lower strain rates, an increased activity of grain boundary sliding causes grain boundaries crack leading to intergranular failure.

Tensile deformation of metallic glass and shape memory alloy nanolaminates

Mechanical deformation of Cu50Zr50 metallic glasses (MGs) with CuZr B2 layers was explored using tensile tests under iso-strain and iso-stress conditions using molecular dynamics simulations. Atomic structure identification was conducted through machine learning techniques, enabling a distinct examination of the deformation exhibited by each phase. Our results revealed early-stage plasticity driven primarily by shear transformation zones at the amorphous/crystalline interface, rather than shear band formation and propagation observed in the monolithic MG, leading to nanolaminates with enhanced strength. Furthermore, under iso-strain deformation, B2 layers underwent martensitic transformation promoted by the nucleation of voids. However, void growth quickly supersedes these effects under both iso-strain and iso-stress conditions, culminating in sample fracture. In summary, this work advances our understanding of amorphous/crystalline nanolaminates, providing valuable insights into their mechanical complexities.

A preliminary investigation on the mechanical behaviour of a stiff Italian clay in the context of hydrogen storage

The large-scale use of renewable energy sources is closely linked to the ability to store excess energy generated during periods of overproduction for use when demand is at a peak. Storing green energy is therefore a key component in the move towards a carbon-neutral economy. Underground hydrogen storage in depleted oil and gas reservoirs may provide an efficient long-term solution. Cyclic injection and production of hydrogen alter the chemo-hydro-mechanical conditions of the reservoir and caprocks, and possible geomechanical consequences of such alterations must be preliminarily assessed for safe storage operations. This study aims at exploring the possible effects of cyclic mechanical loads, such as those that might be induced by hydrogen storage and production, on the mechanical behaviour of a clayey caprock. A series of triaxial tests, both monotonic and cyclic, were carried out on undisturbed samples of a stiff Italian clay cored from a caprock formation overlying a hydrocarbon reservoir. The results show that the material response is characterized by the distinctive stress-strain behaviour of stiff clays, with a rather high fragility, which was found to be highly dependent on the loading strain rate. During laboratory experiments conducted at frequencies larger than in situ ones, cyclic loading under stress control causes a gradual degradation of the material structure leading to the formation of a clear shear band followed by a reduction in shear strength. Eventually, failure occurs as the peak shear strength approaches the applied load. The progressive destructuration also implies a reduction in P- and S-wave propagation velocities and a significant change in the signal shape, which is therefore a promising parameter for monitoring the material degradation process.

Effect of aging state on low cycle fatigue performance of AA 2099 alloy

The evaluation of the fatigue performance is a crucial subject in the research of structural materials utilized in the field of aerospace engineering. In order to examine the influence of aging state on fatigue performance, low cycle fatigue (LCF) experiments were conducted on specimens made from AA2099 alloy in the under-aged (UA), peak-aged (PA), and over-aged (OA) states, with varying strain amplitudes (Δεt/2=0.3 %-0.5 %). In the UA and PA states, the grain boundary precipitates exhibit a small size, thereby prompting the crack to propagate through the grains. Certain grains in this region exhibit a crystallographic feature of crack propagation along the (111) slip plane, which is associated with the formation of the precipitation free bands (T1-PFB) within the grains. In contrast, in the OA state, the size of the grain boundary precipitates increases significantly, accompanied by a minimum precipitation free zones (PFZs) width increase to 75 nm, exacerbating the stress concentration at grain boundaries, with cracks primarily extending along the grain boundaries. Furthermore, the presence of coarse grain boundary precipitates and the widened PFZs promote the initiation and propagation of fatigue cracks, leading to a pronounced reduction in fatigue life.

Increase in interplanar distances and formation of amorphous shear bands in deformed diamond

Amorphous transformation-deformation bands have been observed in diamond under cyclic loading (at planetary ball milling) near the graphite-diamond equilibrium line at temperatures below the Debye temperature. The maximum stresses and temperature in the diamond do not exceed 6 GPa and 420 K, respectively. These bands add to the set of plastic deformation mechanisms in diamond. TEM methods and conventional X-rays were used to investigate the mechanisms of plastic deformation of diamond. The observed mechanisms include amorphous deformation bands, bond breaking, twin formation, and phase transitions of diamond-lonsdaleite and diamond-onions. The increased interplanar distances provide evidence of the plastic deformation mechanism due to bond breaking. The distances of 0.222 and 0.255 nm are significantly larger than the initial value of 0.206 nm, which is characteristic of d111 diamond. This increase in distance cannot be attributed to lattice expansion caused by point defects, but rather to the breakage of interatomic bonds.

Strength and Fracture Toughness of Type 304 and 316 Austenitic Stainless Steels at 4.2 K

The tensile properties and fracture toughness of type 304L, 316L and 316LN austenitic stainless steels and their weldments at cryogenic temperatures have been summarized in the literature. Rolled plates showed a trade-off relationship between 0.2% proof stress and planestrain fracture toughness with those at 4.2 K. The 0.2% proof stress increases with increasing C+N content, and the fracture toughness depends on their austenite stability to α’-martensitic transformation at the crack tip. The formation of shear bands at low strains is directly related to fracture toughness. The stacking fault energy represents the shear-band formation as well as slip deformation manner, so alloy design with higher Ni, Mn, and Mo contents in the chemical composition range of 316LN would be desirable to improve fracture toughness due to higher stacking fault energy.

A strong and ductile biocompatible Ti40Zr25Nb25Ta5Mo5 high entropy alloy

A non-equiatomic high entropy alloy (HEA) Ti40Nb25Zr25Ta5Mo5 (at.%) was designed by replacing 5% Ta with 5% Mo in a precursor Ti40Nb25Zr25Ta10 HEA for improved mechanical properties and reduced density. The Ti40Nb25Zr25Ta5Mo5 HEA fabricated by copper mould casting exhibited a nearly equiaxed grain structure (grain size: 96 ± 16 μm), but within each equiaxed grain, dendritic structures are discernible in the backscattered electron imaging mode. These dendrites are enriched in Ta, Nb and Mo, while the inter-dendritic regions contain higher Zr and Ti. The as-cast HEA achieved tensile yield strength (σ0.2) of 976 ± 8 MPa and strain to fracture (εf) of 16.80 ± 1.86%, well above the minimum requirements of σ0.2 and εf for medical-grade titanium alloy Ti–6Al–4V (759 MPa and 10%). The formation of microscale and nanoscale shear bands and the presence of significant dislocations in the shear band boundary region played a key role in allowing this as-cast HEA to achieve the excellent combination of tensile strength and ductility. Furthermore, the HEA exhibited a lower wear rate, lower coefficient of friction and much higher corrosion resistance in Hank's solution (electrochemical assessments) than Ti–6Al–4V, making it a promising alternative biomedical alloy.

Capturing of neurotoxins causing diabetes stress and nervous breakdown in the aqueous medium by naphthazarin esters.

The fear of an increase in blood sugar can be very traumatic. Being diabetic either type I or type II leads to a disorder called diabetes distress having traits of stress, depression, and anxiety. Among risk factors of diabetes mellitus heavy and trace metal toxicity emerges as new risk factors reported in many studies. In this study we target toxic metals, viz., Ni2+, Zn2+, and Cu2+, involved in the pathogenesis of diabetes and diabetic stress with naphthazarin esters. The compounds C1-C3 isolated from the leaves and roots of Arnebia guttata were tested for their metal-binding ability in an aqueous medium in UV-Visible and nuclear magnetic resonance (NMR) studies. These probes are well-known naphthoquinones present in the Arnebia species. In the UV-Visible titrations of compounds C1-C3 with Na2+, K2+, Zn2+, Ca2+, Cu2+, Mg2+, Co2+, and Ni2+ ions, significant binding was observed with Ni2+, Cu2+, and Zn2+ ions in MeOH/H2O. There occurs a beautiful formation of red-shifted bands between the 520 to 620 nm range with a synergistic increase in absorbance. Also, the disappearance of proton peaks in the 1H NMR spectrum on addition of metal ions confirmed binding. Compounds C1-C3 isolated from A. guttata came out as potent Ni2+, Zn2+, and Cu2+ sensors that are reportedly involved in islet function and induction of diabetes.

Transverse difference of activation slip/twin system in wide AZ31 alloy plate during its rolling

The macroscopic finite element method (FEM) and the crystal plasticity finite element method (CPFEM) were combined to study the transverse difference of activation slip/twin system in wide AZ31 magnesium alloy plates during rolling. The macro-deformation and micro-texture evolution along the transverse direction of the plate during rolling were analyzed experimentally. The microscopic CPFEM was developed on the basis of the thermo-force coupling behavior during plate rolling obtained from macroscopic FEM. The CPFEM parameters were fitted by uniaxial compression experiments. This combination of two scale simulations accurately predicted the texture evolution during the rolling process and had been experimentally validated. Further examination of the deformation mechanism reveals that the transverse spread action of the plate is stronger at the edge region compared to center, and this transverse spread action has a more significant impact on the activation of the {10 1‾ 2} tension twin. The comparison of the activation and extension of pyramidal <a> slip in granular and plate-like grains reveals that plate-like grains are more prone to generate slip bands through the grain, leading to cracking of the grain along the slip activation band and further formation of sub-grains.

Study of energy dissipation mechanisms and hotspot formation patterns during impact process in octogen explosives with circular cavities

Considerable focus has been given to hotspot generation and ignition phenomena in impact-induced explosives. Hotspot formation in explosives is typically attributed to internal dissipation and heat transfer occurring within them. This study refines the momentum and energy equations to illustrate the entire process of particle collision, temperature-rise evolution, and hotspot formation in octogen explosive bed under impact. By octogen, we mean the substance known as cyclotetramethylene tetranitramine, which is also commonly referred to as HMX. Dense particles are considered to have pseudo-fluid properties. During the impact of the explosive, we captured the propagation of the stress wave and compared its similarities and differences with the shock wave. The collision force model incorporates a combination of Hertz–Mindlin elastic and Thornton elastoplastic contact theories. The temperature-governing equation includes sliding friction, rolling resistance, and plastic dissipations as energy sources, taking into account the heat transfer processes between particles. Temperature evolution is a spatiotemporally correlated phenomenon divided into three processes: high-temperature bands formation, cavity collapse, and particle bed dispersion, all of which lead to hotspot formation near the cavity and near the wall. Plastic dissipation is the primary source for particle temperature-rise and hotspot formation. Furthermore, the effect of cavity size, impact velocity, and particle size on temperature evolution and hotspot formation patterns is analyzed. It was found that higher impact velocities and smaller cavity sizes are associated with increased hotspot temperatures near the wall, but the hotspot temperature near the cavity does not consistently vary with impact velocity and cavity size. This is attributed to the relationship between energy dissipation rate and void collapse time.

Study on strain localization of frozen sand based on uniaxial compression test and discrete element simulation

Strain localization has always been an important subject in frozen soil mechanics and engineering. To evaluate the development of local strain and the formation of shear bands in frozen soil, uniaxial compression tests have been conducted on frozen sand at various temperatures and particle grades. The strain localization evolution law of the frozen soil is analyzed utilizing the digital image correlation (DIC) method. The test results reveal that the entire process of shear band generation, development, and formation in frozen soil can be well captured. Within the testing temperature and particle grade range in this study, in comparison to particle grade, temperature exerts a more pronounced influence on the shear band angle which increases as temperature decreases. It is discovered that the width of the shear band increases with the decrease in temperature and the increase in mean particle diameter d50. Subsequently, a discrete element method (DEM) model is developed to examine the microscopic mechanical characteristics of frozen sand in uniaxial compression tests. The reliability of the DEM model is verified through comparative analysis with test results. Besides, the development law of the strain localization of the frozen soil obtained by the numerical simulation is revealed based on the quantitative analysis of the rotational angle, bonding state, and displacement of the soil particle during the shearing process.

Enhanced sensitivity for Aflatoxin B1 detection in food through a h-Zn1Cd5S-based photoelectrochemical aptasensor

Designing photoelectrochemical sensors for detecting ultra-trace amounts of Aflatoxin B1 (AFB1) in complex samples poses a significant challenge. In pursuit of this objective, we engineered hollow-structured ZnCdS (denoted as h-Zn1Cd5S) material and applied an electrodeposition method to introduce Au nanoparticles (AuNPs) on the surface. This approach resulted in a significant enhancement of the photocurrent response of the photoelectrode, attributed to the synergistic effects of the hollow structure and surface plasmon resonance, thereby underscoring its potential for advanced applications. Utilizing density functional theory, we computed the transfer route and energy band formation of photogenerated electrons. Subsequently, we developed an AFB1 photoelectrochemical (PEC) aptasensor based on the competition mechanism, coupled with aptamer probe technology. This aptasensor allows for the ultra-trace determination of AFB1, exhibiting a remarkable detection limit as low as 1.32 fg/mL and a linear range from 1.0 × 10−2 to 100.0 pg/mL. The PEC aptasensor for AFB1 demonstrates excellent sensitivity and selectivity. When applied to the detection of AFB1 in Tsaoko, wheat, and corn samples, its performance aligns closely with high-performance liquid chromatography (HPLC) results, validating its applicability for analyzing real-world samples.

Band gap engineering and controlling transport properties of single photons in periodic and disordered Jaynes–Cummings arrays

We theoretically study the single-photon transport properties in periodic and position-disordered Jaynes–Cummings (or JC) arrays of waveguide-coupled microtoroidal ring resonators, each interacting with a single two-level quantum emitter. Employing the real-space formalism of quantum optics, we focus on various parameter regimes of cavity quantum electrodynamics (cQED) to gain better control of single-photon propagation in such a many-body quantum optical setting. As for some of the key findings, we observe that the periodic setting leads to the formation of the band structure in the photon transmission spectra, which is most evident in the strong coupling regime of cQED. However, under resonant conditions with no losses, the application of Bloch’s theorem indicates that the width of forbidden gaps can be altered by tuning the emitter-cavity coupling to small values. Moreover, in the disordered case, we find that the single-photon transmission curves show the disappearance of band formation. However, spectral features originating from cQED interactions observed for the single atom-cavity problem remain robust against weak-disordered conditions. The results of this work may find application in the study of quantum many-body effects in the optical domain as well as in different areas of quantum computation and quantum networking.

Excellent specific strength-ductility synergy in novel complex concentrated alloy after suction casting

Lightweight alloys are known to improve the fuel efficiency of the structural components due to high strength-to-weight ratio, however, they lack formability at room temperature. This major limitation of poor formability is most of the time overcome by post-fabrication processing and treatments thereby increasing their cost exponentially. We present a novel Ti50V16Zr16Nb10Al5Mo3 (all in at. %) complex concentrated alloy (Ti-CCA) designed based on the combination of valence electron concentration theory and the high entropy approach. The optimal selection of constituent elements has led to a density of 5.63 gm/cc for Ti-CCA after suction casting (SC). SC Ti-CCA displayed exceptional room temperature strength (UTS ∼ 1.25 GPa) and ductility (ε ∼ 35 %) with a yield strength (YS) of ∼ 1.1 GPa (Specific YS = 191 MPa/gm/cc) without any post-processing treatments. The exceptional YS in Ti-CCA is attributed to hetero grain size microstructure, whereas enormous strength-ductility synergy is due to the concurrent occurrence of slip and deformation band formation in the early stages of deformation followed by prolonged necking event due to delayed void nucleation and growth. The proposed philosophy of Ti-CCA design overcomes the conventional notion of strength-ductility trade-off in such alloy systems by retaining their inherent characteristics.

Structural, phonon, optical, electronic, and thermodynamic properties of NpX (X = S, Se, Te) chalcogenides: A DFT study

Binary chalcogenides with small Reststrahlen bands in the far infrared and microwave region make them intriguing for IR sensors and radar communication purposes. In this study, we have theoretically investigated the structural, phonon, electronic, optical, IR optical and thermodynamic properties of NpX, where X = S, Se, and Te chalcogenides. The face-centered cubic structure is relaxed to determine the optimized lattice parameters which increased with an increase in the size of involving chalcogen atom. Band structure reveals their metallic nature. The significant contribution of d and f-states of Np and p-states of chalcogens in band formation is evident from the density of state plots. The detailed analysis of optical parameters including real and imaginary parts of dielectric constant and refractive index, optical conductivity, and optical loss exhibit high absorption in the IR region.